OpenWrt_x86-r2s-r4s-r5s-N1/devices/mediatek_filogic/patches/17-lc-hx3001.patch

From 5eacf09258839ccda9172962287727ab8825f90b Mon Sep 17 00:00:00 2001
From: Chen Minqiang <[email protected]>
Date: Sat, 16 Dec 2023 07:39:20 +0800
Subject: [PATCH] mediatek: add IMOU LC-HX3001 (uboot layout)

---
 .../mt7981b-imou-lc-hx3001.dts    | 239 ++++++++++++++++++
 .../filogic/base-files/etc/board.d/01_leds    |   5 +
 .../filogic/base-files/etc/board.d/02_network |   7 +
 .../etc/hotplug.d/ieee80211/11_fix_wifi_mac   |   6 +
 target/linux/mediatek/image/filogic.mk        |  23 ++
 5 files changed, 280 insertions(+)
 create mode 100644 target/linux/mediatek/dts/mt7981b-imou-lc-hx3001.dts

diff --git a/target/linux/mediatek/dts/mt7981b-imou-lc-hx3001.dts b/target/linux/mediatek/dts/mt7981b-imou-lc-hx3001.dts
new file mode 100644
index 0000000000000..857f2a534e112
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-imou-lc-hx3001.dts
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7981.dtsi"
+
+/ {
+	model = "IMOU LC-HX3001 (uboot layout)";
+	compatible = "imou,lc-hx3001", "mediatek,mt7981";
+
+	aliases {
+		led-boot = &power_led;
+		led-failsafe = &power_led;
+		led-running = &power_led;
+		led-upgrade = &power_led;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x10000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		button-mesh {
+			label = "mesh";
+			linux,code = <BTN_9>;
+			linux,input-type = <EV_SW>;
+			gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power_led: led-0 {
+			label = "green:power";
+			gpios = <&pio 4 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			label = "green:wlan";
+			gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			label = "red:wan";
+			gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			label = "green:wan";
+			gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			label = "green:lan";
+			gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins>;
+
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "gmii";
+		phy-handle = <&int_gbe_phy>;
+	};
+};
+
+&mdio_bus {
+	switch: switch@1f {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_flash_pins>;
+	status = "okay";
+
+	spi_nand: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+
+		spi-cal-enable;
+		spi-cal-mode = "read-data";
+		spi-cal-datalen = <7>;
+		spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
+		spi-cal-addrlen = <5>;
+		spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		mediatek,nmbm;
+		mediatek,bmt-max-ratio = <1>;
+		mediatek,bmt-max-reserved-blocks = <64>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "BL2";
+				reg = <0x00000 0x100000>;
+			};
+
+			partition@100000 {
+				label = "u-boot-env";
+				reg = <0x100000 0x80000>;
+			};
+
+			factory: partition@180000 {
+				label = "Factory";
+				reg = <0x180000 0x200000>;
+			};
+
+			partition@380000 {
+				label = "FIP";
+				reg = <0x380000 0x200000>;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x580000 0x7280000>;
+			};
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	spi0_flash_pins: spi0-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+			drive-strength = <8>;
+			bias-pull-up = <103>;
+		};
+
+		conf-pd {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+			drive-strength = <8>;
+			bias-pull-down = <103>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+
+	mediatek,mtd-eeprom = <&factory 0x0>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 0a1f642c70924..fda3d4b98d875 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -20,6 +20,14 @@ confiabits,mt7981)
 cudy,wr3000-v1)
 	ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan"
 	;;
+imou,lc-hx3001)
+	ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1" "link"
+	ucidef_set_led_netdev "lan" "LAN" "green:lan" "br-lan" "link"
+	ucidef_set_led_netdev "wlan" "WLAN" "green:wlan" "phy1-ap0" "link"
+	;;
+konka,komi-a31)
+         ucidef_set_led_netdev "eth1" "eth1" "blue:status" "eth1" "link"
+	;;
 mercusys,mr90x-v1)
 	ucidef_set_led_netdev "lan-0" "lan-0" "green:lan-0" "lan0" "link tx rx"
 	ucidef_set_led_netdev "lan-1" "lan-1" "green:lan-1" "lan1" "link tx rx"
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 61637e09c7f0e..4048eddadb45a 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -130,6 +130,12 @@
 		wan_mac=$label_mac
 		lan_mac=$(macaddr_add "$label_mac" 2)
 		;;
+	imou,lc-hx3001)
+		lan_mac=$(mtd_get_mac_ascii u-boot-env mac)
+		[ -n "$lan_mac" ] || lan_mac=$(macaddr_add $(mtd_get_mac_binary Factory 0x4) -1)
+		wan_mac=$(macaddr_add $lan_mac 2)
+		label_mac="$lan_mac"
+		;;
 	h3c,magic-nx30-pro)
 		wan_mac=$(mtd_get_mac_ascii pdt_data_1 ethaddr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 83428f0d981e7..6d2e9d713be02 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -589,6 +589,50 @@ endif
 endef
 TARGET_DEVICES += h3c_magic-nx30-pro-nmbm
 
+define Device/imou_lc-hx3001
+  DEVICE_VENDOR := IMOU
+  DEVICE_MODEL := LC-HX3001
+  DEVICE_DTS := mt7981b-imou-lc-hx3001
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+  SUPPORTED_DEVICES += imou,lc-hx3001
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 113152k
+  KERNEL_IN_UBI := 1
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  KERNEL = kernel-bin | lzma | \
+	fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  KERNEL_INITRAMFS = kernel-bin | lzma | \
+	fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
+endef
+TARGET_DEVICES += imou_lc-hx3001
+
+define Device/konka_komi-a31
+  DEVICE_VENDOR := KONKA
+  DEVICE_MODEL := KOMI A31
+  DEVICE_DTS := mt7981b-konka-komi-a31
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+  SUPPORTED_DEVICES := konka,komi-a31
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 114688k
+  KERNEL_IN_UBI := 1
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  KERNEL = kernel-bin | lzma | \
+       fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  KERNEL_INITRAMFS = kernel-bin | lzma | \
+       fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
+endef
+TARGET_DEVICES += konka_komi-a31
+
 define Device/jcg_q30-pro
   DEVICE_VENDOR := JCG
   DEVICE_MODEL := Q30 PRO