ramips: add support for TP-Link RE200 v3

TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button

Unverified:
- UART header on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.

Signed-off-by: Richard Fröhning <[email protected]>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <[email protected]>

target/linux/ramips/dts/mt7628an_tplink_re200-v3.dts

@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7628an_tplink_re200.dtsi"
+
+/ {
+	compatible = "tplink,re200-v3", "mediatek,mt7628an-soc";
+	model = "TP-Link RE200 v3";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wps {
+			label = "re200-v3:green:wps";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi {
+			label = "re200-v3:green:wifi";
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "re200-v3:green:lan";
+			gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+		};
+
+		led_power: power {
+			label = "re200-v3:green:power";
+			gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi2g_green {
+			label = "re200-v3:green:wifi2g";
+			gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wifi5g_green {
+			label = "re200-v3:green:wifi5g";
+			gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wifi2g_red {
+			label = "re200-v3:red:wifi2g";
+			gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi5g_red {
+			label = "re200-v3:red:wifi5g";
+			gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "p4led_an", "p3led_an", "p2led_an", "p1led_an",
+				"p0led_an", "wled_an", "i2c", "wdt", "refclk";
+		function = "gpio";
+	};
+};

target/linux/ramips/image/mt76x8.mk

@@ -404,6 +404,16 @@ define Device/tplink_re200-v2
 endef
 TARGET_DEVICES += tplink_re200-v2
 
+define Device/tplink_re200-v3
+  $(Device/tplink-safeloader)
+  IMAGE_SIZE := 7808k
+  DEVICE_MODEL := RE200
+  DEVICE_VARIANT := v3
+  DEVICE_PACKAGES := kmod-mt76x0e
+  TPLINK_BOARD_ID := RE200-V3
+endef
+TARGET_DEVICES += tplink_re200-v3
+
 define Device/tplink_re220-v2
   $(Device/tplink-safeloader)
   IMAGE_SIZE := 7808k

target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds

@@ -69,6 +69,7 @@ tplink,archer-c50-v4)
 	ucidef_set_led_wlan "wlan5g" "wlan5g" "$boardname:green:wlan5g" "phy1tpt"
 	;;
 tplink,re200-v2|\
+tplink,re200-v3|\
 tplink,re220-v2|\
 tplink,tl-mr3020-v3|\
 tplink,tl-wa801nd-v5)

target/linux/ramips/mt76x8/base-files/etc/board.d/02_network

@@ -19,6 +19,7 @@ ramips_setup_interfaces()
 	ravpower,rp-wd009|\
 	tama,w06|\
 	tplink,re200-v2|\
+	tplink,re200-v3|\
 	tplink,re220-v2|\
 	tplink,re305-v1|\
 	tplink,tl-mr3020-v3|\

tools/firmware-utils/src/tplink-safeloader.c

@@ -1562,6 +1562,50 @@ static struct device_info boards[] = {
 		.last_sysupgrade_partition = "file-system"
 	},
 
+  /** Firmware layout for the RE200 v3 */
+	{
+		.id     = "RE200-V3",
+		.vendor = "",
+		.support_list =
+			"SupportList:\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:00000000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:41520000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:41550000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:42520000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:43410000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:45470000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:45530000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:45550000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:49440000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:4A500000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:4B520000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:52550000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:54570000}\n"
+			"{product_name:RE200,product_ver:3.0.0,special_id:55530000}\n",
+		.support_trail = '\x00',
+		.soft_ver = NULL,
+
+		.partitions = {
+			{"fs-uboot", 0x00000, 0x20000},
+			{"firmware", 0x20000, 0x7a0000},
+			{"partition-table", 0x7c0000, 0x02000},
+			{"default-mac", 0x7c2000, 0x00020},
+			{"pin", 0x7c2100, 0x00020},
+			{"product-info", 0x7c3100, 0x01000},
+			{"soft-version", 0x7c4200, 0x01000},
+			{"support-list", 0x7c5200, 0x01000},
+			{"profile", 0x7c6200, 0x08000},
+			{"config-info", 0x7ce200, 0x00400},
+			{"user-config", 0x7d0000, 0x10000},
+			{"default-config", 0x7e0000, 0x10000},
+			{"radio", 0x7f0000, 0x10000},
+			{NULL, 0, 0}
+		},
+
+		.first_sysupgrade_partition = "os-image",
+		.last_sysupgrade_partition = "file-system"
+	},
+
 	/** Firmware layout for the RE220 v2 */
 	{
 		.id     = "RE220-V2",