brcm47xx: add initial support for kernel 3.14

Signed-off-by: Hauke Mehrtens <[email protected]>

SVN-Revision: 39905

package/kernel/broadcom-diag/Makefile

@@ -15,7 +15,7 @@ include $(INCLUDE_DIR)/package.mk
 
 define KernelPackage/diag
   SUBMENU:=Other modules
-  DEPENDS:=@TARGET_brcm47xx
+  DEPENDS:=@TARGET_brcm47xx @!LINUX_3_14
   TITLE:=Driver for router LEDs and Buttons
   FILES:=$(PKG_BUILD_DIR)/diag.ko
   AUTOLOAD:=$(call AutoLoad,05,diag,1)

target/linux/brcm47xx/config-3.14

@@ -0,0 +1,172 @@
+CONFIG_ADM6996_PHY=y
+CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
+CONFIG_ARCH_DISCARD_MEMBLOCK=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_B53=y
+# CONFIG_B53_MMAP_DRIVER is not set
+CONFIG_B53_PHY_DRIVER=y
+CONFIG_B53_PHY_FIXUP=y
+# CONFIG_B53_SRAB_DRIVER is not set
+CONFIG_BCM47XX=y
+CONFIG_BCM47XX_BCMA=y
+CONFIG_BCM47XX_SSB=y
+CONFIG_BCM47XX_WDT=y
+CONFIG_BCMA=y
+CONFIG_BCMA_BLOCKIO=y
+CONFIG_BCMA_DEBUG=y
+CONFIG_BCMA_DRIVER_GMAC_CMN=y
+CONFIG_BCMA_DRIVER_GPIO=y
+CONFIG_BCMA_DRIVER_MIPS=y
+CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
+CONFIG_BCMA_HOST_PCI=y
+CONFIG_BCMA_HOST_PCI_POSSIBLE=y
+CONFIG_BCMA_HOST_SOC=y
+CONFIG_BCMA_NFLASH=y
+CONFIG_BCMA_SFLASH=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_CMDLINE="noinitrd console=ttyS0,115200"
+CONFIG_CMDLINE_BOOL=y
+# CONFIG_CMDLINE_OVERRIDE is not set
+# CONFIG_CPU_BMIPS is not set
+CONFIG_CPU_GENERIC_DUMP_TLB=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+CONFIG_CPU_MIPSR1=y
+CONFIG_CPU_MIPSR2_IRQ_VI=y
+CONFIG_CPU_R4K_CACHE_TLB=y
+CONFIG_CPU_R4K_FPU=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_CSRC_R4K=y
+CONFIG_DMA_NONCOHERENT=y
+# CONFIG_EARLY_PRINTK is not set
+CONFIG_FIXED_PHY=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_NET_UTILS=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_DEVRES=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_WDT=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ_PERIODIC=y
+CONFIG_IMAGE_CMDLINE_HACK=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IRQ_CPU=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_LEDS_GPIO_REGISTER=y
+CONFIG_MDIO_BOARDINFO=y
+CONFIG_MIPS=y
+# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MACHINE is not set
+CONFIG_MIPS_MT_DISABLED=y
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+# CONFIG_MLX5_CORE is not set
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_BCM47XXSFLASH=y
+CONFIG_MTD_BCM47XX_PARTS=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_BCM47XXNFLASH=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_SM_COMMON is not set
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NET_RX_BUSY_POLL=y
+CONFIG_NO_EXCEPT_FILL=y
+CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PCI=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PHYLIB=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_STALL_COMMON is not set
+# CONFIG_SCSI_DMA is not set
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SSB=y
+CONFIG_SSB_B43_PCI_BRIDGE=y
+CONFIG_SSB_BLOCKIO=y
+CONFIG_SSB_DEBUG=y
+CONFIG_SSB_DRIVER_EXTIF=y
+CONFIG_SSB_DRIVER_GIGE=y
+CONFIG_SSB_DRIVER_GPIO=y
+CONFIG_SSB_DRIVER_MIPS=y
+CONFIG_SSB_DRIVER_PCICORE=y
+CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
+CONFIG_SSB_EMBEDDED=y
+CONFIG_SSB_PCICORE_HOSTMODE=y
+CONFIG_SSB_PCIHOST=y
+CONFIG_SSB_PCIHOST_POSSIBLE=y
+CONFIG_SSB_SERIAL=y
+CONFIG_SSB_SFLASH=y
+CONFIG_SSB_SPROM=y
+CONFIG_SWCONFIG=y
+CONFIG_SYS_HAS_CPU_BMIPS=y
+CONFIG_SYS_HAS_CPU_BMIPS32_3300=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_CPU_MIPS32_R2=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_USB_SUPPORT=y
+CONFIG_WATCHDOG_CORE=y
+# CONFIG_ZBUD is not set
+CONFIG_ZONE_DMA_FLAG=0

target/linux/brcm47xx/patches-3.14/027-mtd-bcm47xxpart-get-nvram.patch

@@ -0,0 +1,34 @@
+--- a/drivers/mtd/bcm47xxpart.c
++++ b/drivers/mtd/bcm47xxpart.c
+@@ -68,6 +68,7 @@ static int bcm47xxpart_parse(struct mtd_
+ 	int trx_part = -1;
+ 	int last_trx_part = -1;
+ 	int possible_nvram_sizes[] = { 0x8000, 0xF000, 0x10000, };
++	bool found_nvram = false;
+ 
+ 	if (blocksize <= 0x10000)
+ 		blocksize = 0x10000;
+@@ -229,12 +230,23 @@ static int bcm47xxpart_parse(struct mtd_
+ 		if (buf[0] == NVRAM_HEADER) {
+ 			bcm47xxpart_add_part(&parts[curr_part++], "nvram",
+ 					     master->size - blocksize, 0);
++			found_nvram = true;
+ 			break;
+ 		}
+ 	}
+ 
+ 	kfree(buf);
+ 
++	if (!found_nvram) {
++		pr_err("can not find a nvram partition reserve last block\n");
++		bcm47xxpart_add_part(&parts[curr_part++], "nvram_guess",
++				     master->size - blocksize * 2, MTD_WRITEABLE);
++		for (i = 0; i < curr_part; i++) {
++			if (parts[i].size + parts[i].offset == master->size)
++				parts[i].offset -= blocksize * 2;
++		}
++	}
++
+ 	/*
+ 	 * Assume that partitions end at the beginning of the one they are
+ 	 * followed by.

target/linux/brcm47xx/patches-3.14/128-MIPS-BCM47XX-Add-new-file-for-device-specific-workar.patch

@@ -0,0 +1,72 @@
+From 1f3e1c682a0b5273e3ee8799b54319971f426e6a Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <[email protected]>
+Date: Wed, 29 Jan 2014 18:06:52 +0100
+Subject: [RFC V2][PATCH] MIPS: BCM47XX: Add new file for device specific workarounds
+
+---
+V2: Drop pr_debug for devices we don't need workarounds for. It was too
+    load and not useful at all.
+---
+ arch/mips/bcm47xx/Makefile          |  2 +-
+ arch/mips/bcm47xx/bcm47xx_private.h |  3 +++
+ arch/mips/bcm47xx/setup.c           |  1 +
+ arch/mips/bcm47xx/workarounds.c     | 25 +++++++++++++++++++++++++
+ 4 files changed, 30 insertions(+), 1 deletion(-)
+ create mode 100644 arch/mips/bcm47xx/workarounds.c
+
+--- a/arch/mips/bcm47xx/Makefile
++++ b/arch/mips/bcm47xx/Makefile
+@@ -4,4 +4,4 @@
+ #
+ 
+ obj-y				+= irq.o nvram.o prom.o serial.o setup.o time.o sprom.o
+-obj-y				+= board.o buttons.o leds.o
++obj-y				+= board.o buttons.o leds.o workarounds.o
+--- a/arch/mips/bcm47xx/bcm47xx_private.h
++++ b/arch/mips/bcm47xx/bcm47xx_private.h
+@@ -9,4 +9,7 @@ int __init bcm47xx_buttons_register(void
+ /* leds.c */
+ void __init bcm47xx_leds_register(void);
+ 
++/* workarounds.c */
++void __init bcm47xx_workarounds(void);
++
+ #endif
+--- a/arch/mips/bcm47xx/setup.c
++++ b/arch/mips/bcm47xx/setup.c
+@@ -282,6 +282,7 @@ static int __init bcm47xx_register_bus_c
+ 	}
+ 	bcm47xx_buttons_register();
+ 	bcm47xx_leds_register();
++	bcm47xx_workarounds();
+ 
+ 	fixed_phy_add(PHY_POLL, 0, &bcm47xx_fixed_phy_status);
+ 	return 0;
+--- /dev/null
++++ b/arch/mips/bcm47xx/workarounds.c
+@@ -0,0 +1,25 @@
++#include "bcm47xx_private.h"
++
++#include <linux/gpio.h>
++#include <bcm47xx_board.h>
++#include <bcm47xx.h>
++
++static void __init bcm47xx_workarounds_netgear_wnr3500l(void)
++{
++	/* Set GPIO 12 to 1 to pass power to the USB port */
++	gpio_set_value(12, 1);
++}
++
++void __init bcm47xx_workarounds(void)
++{
++	enum bcm47xx_board board = bcm47xx_board_get();
++
++	switch (board) {
++	case BCM47XX_BOARD_NETGEAR_WNR3500L:
++		bcm47xx_workarounds_netgear_wnr3500l();
++		break;
++	default:
++		/* No workaround(s) needed */
++		break;
++	}
++}

target/linux/brcm47xx/patches-3.14/139-MIPS-BCM47XX-detect-more-linksys-devices.patch

@@ -0,0 +1,39 @@
+From b09189336f6d974c554aed03b4651e9f68ce0abd Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <[email protected]>
+Date: Sun, 23 Feb 2014 16:38:29 +0100
+Subject: [PATCH 3/6] MIPS: BCM47XX: detect some more Linksys devices
+
+The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
+the same gpio configuration. The boardtype numbers are changing with
+the hardware versions, but these hardware numbers are different or each
+model.
+Detect them all as one device, this also worked in OpenWrt.
+---
+ arch/mips/bcm47xx/board.c                          |    4 +++-
+ arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h |    2 +-
+ 2 files changed, 4 insertions(+), 2 deletions(-)
+
+--- a/arch/mips/bcm47xx/board.c
++++ b/arch/mips/bcm47xx/board.c
+@@ -175,7 +175,9 @@ struct bcm47xx_board_type_list3 bcm47xx_
+ 	{{BCM47XX_BOARD_PHICOMM_M1, "Phicomm M1"}, "0x0590", "80", "0x1104"},
+ 	{{BCM47XX_BOARD_ZTE_H218N, "ZTE H218N"}, "0x053d", "1234", "0x1305"},
+ 	{{BCM47XX_BOARD_NETGEAR_WNR3500L, "Netgear WNR3500L"}, "0x04CF", "3500", "02"},
+-	{{BCM47XX_BOARD_LINKSYS_WRT54GSV1, "Linksys WRT54GS V1"}, "0x0101", "42", "0x10"},
++	{{BCM47XX_BOARD_LINKSYS_WRT54G, "Linksys WRT54G/GS/GL"}, "0x0101", "42", "0x10"},
++	{{BCM47XX_BOARD_LINKSYS_WRT54G, "Linksys WRT54G/GS/GL"}, "0x0467", "42", "0x10"},
++	{{BCM47XX_BOARD_LINKSYS_WRT54G, "Linksys WRT54G/GS/GL"}, "0x0708", "42", "0x10"},
+ 	{ {0}, NULL},
+ };
+ 
+--- a/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
++++ b/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
+@@ -66,7 +66,7 @@ enum bcm47xx_board {
+ 	BCM47XX_BOARD_LINKSYS_WRT310NV1,
+ 	BCM47XX_BOARD_LINKSYS_WRT310NV2,
+ 	BCM47XX_BOARD_LINKSYS_WRT54G3GV2,
+-	BCM47XX_BOARD_LINKSYS_WRT54GSV1,
++	BCM47XX_BOARD_LINKSYS_WRT54G,
+ 	BCM47XX_BOARD_LINKSYS_WRT610NV1,
+ 	BCM47XX_BOARD_LINKSYS_WRT610NV2,
+ 	BCM47XX_BOARD_LINKSYS_WRTSL54GS,

target/linux/brcm47xx/patches-3.14/140-MIPS-BCM47XX-add-button-and-led-configuration-for-so.patch

@@ -0,0 +1,133 @@
+From e3d15471f1be2bd2fd4db82907ad4b2d74ec2636 Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <[email protected]>
+Date: Fri, 10 Jan 2014 23:55:28 +0100
+Subject: [PATCH 4/6] MIPS: BCM47XX: add button and led configuration for some
+ Linksys devices
+
+This adds led and button GPIO configuration for Linksys wrt54g3gv2,
+wrt54gsv1 and wrtsl54gs. This is based on OpenWrt broadcom-diag code.
+
+Signed-off-by: Hauke Mehrtens <[email protected]>
+---
+ arch/mips/bcm47xx/buttons.c |   27 +++++++++++++++++++++++++++
+ arch/mips/bcm47xx/leds.c    |   33 +++++++++++++++++++++++++++++++++
+ 2 files changed, 60 insertions(+)
+
+--- a/arch/mips/bcm47xx/buttons.c
++++ b/arch/mips/bcm47xx/buttons.c
+@@ -259,6 +259,18 @@ bcm47xx_buttons_linksys_wrt310nv1[] __in
+ };
+ 
+ static const struct gpio_keys_button
++bcm47xx_buttons_linksys_wrt54g3gv2[] __initconst = {
++	BCM47XX_GPIO_KEY(5, KEY_WIMAX),
++	BCM47XX_GPIO_KEY(6, KEY_RESTART),
++};
++
++static const struct gpio_keys_button
++bcm47xx_buttons_linksys_wrt54gsv1[] __initconst = {
++	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
++	BCM47XX_GPIO_KEY(6, KEY_RESTART),
++};
++
++static const struct gpio_keys_button
+ bcm47xx_buttons_linksys_wrt610nv1[] __initconst = {
+ 	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+ 	BCM47XX_GPIO_KEY(8, KEY_WPS_BUTTON),
+@@ -270,6 +282,12 @@ bcm47xx_buttons_linksys_wrt610nv2[] __in
+ 	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+ };
+ 
++static const struct gpio_keys_button
++bcm47xx_buttons_linksys_wrtsl54gs[] __initconst = {
++	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
++	BCM47XX_GPIO_KEY(6, KEY_RESTART),
++};
++
+ /* Motorola */
+ 
+ static const struct gpio_keys_button
+@@ -479,12 +497,21 @@ int __init bcm47xx_buttons_register(void
+ 	case BCM47XX_BOARD_LINKSYS_WRT310NV1:
+ 		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt310nv1);
+ 		break;
++	case BCM47XX_BOARD_LINKSYS_WRT54G:
++		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt54gsv1);
++		break;
++	case BCM47XX_BOARD_LINKSYS_WRT54G3GV2:
++		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt54g3gv2);
++		break;
+ 	case BCM47XX_BOARD_LINKSYS_WRT610NV1:
+ 		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt610nv1);
+ 		break;
+ 	case BCM47XX_BOARD_LINKSYS_WRT610NV2:
+ 		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt610nv2);
+ 		break;
++	case BCM47XX_BOARD_LINKSYS_WRTSL54GS:
++		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrtsl54gs);
++		break;
+ 
+ 	case BCM47XX_BOARD_MOTOROLA_WE800G:
+ 		err = bcm47xx_copy_bdata(bcm47xx_buttons_motorola_we800g);
+--- a/arch/mips/bcm47xx/leds.c
++++ b/arch/mips/bcm47xx/leds.c
+@@ -292,6 +292,21 @@ bcm47xx_leds_linksys_wrt310nv1[] __initc
+ };
+ 
+ static const struct gpio_led
++bcm47xx_leds_linksys_wrt54gsv1[] __initconst = {
++	BCM47XX_GPIO_LED(0, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
++	BCM47XX_GPIO_LED(5, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(7, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
++};
++
++static const struct gpio_led
++bcm47xx_leds_linksys_wrt54g3gv2[] __initconst = {
++	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
++	BCM47XX_GPIO_LED(2, "green", "3g", 0, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(3, "blue", "3g", 0, LEDS_GPIO_DEFSTATE_OFF),
++};
++
++static const struct gpio_led
+ bcm47xx_leds_linksys_wrt610nv1[] __initconst = {
+ 	BCM47XX_GPIO_LED(0, "unk", "usb",  1, LEDS_GPIO_DEFSTATE_OFF),
+ 	BCM47XX_GPIO_LED(1, "unk", "power",  0, LEDS_GPIO_DEFSTATE_OFF),
+@@ -308,6 +323,15 @@ bcm47xx_leds_linksys_wrt610nv2[] __initc
+ 	BCM47XX_GPIO_LED(7, "unk", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+ };
+ 
++static const struct gpio_led
++bcm47xx_leds_linksys_wrtsl54gs[] __initconst = {
++	BCM47XX_GPIO_LED(0, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
++	BCM47XX_GPIO_LED(2, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(3, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(7, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
++};
++
+ /* Motorola */
+ 
+ static const struct gpio_led
+@@ -502,12 +526,21 @@ void __init bcm47xx_leds_register(void)
+ 	case BCM47XX_BOARD_LINKSYS_WRT310NV1:
+ 		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt310nv1);
+ 		break;
++	case BCM47XX_BOARD_LINKSYS_WRT54G:
++		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt54gsv1);
++		break;
++	case BCM47XX_BOARD_LINKSYS_WRT54G3GV2:
++		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt54g3gv2);
++		break;
+ 	case BCM47XX_BOARD_LINKSYS_WRT610NV1:
+ 		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt610nv1);
+ 		break;
+ 	case BCM47XX_BOARD_LINKSYS_WRT610NV2:
+ 		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt610nv2);
+ 		break;
++	case BCM47XX_BOARD_LINKSYS_WRTSL54GS:
++		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrtsl54gs);
++		break;
+ 
+ 	case BCM47XX_BOARD_MOTOROLA_WE800G:
+ 		bcm47xx_set_pdata(bcm47xx_leds_motorola_we800g);

target/linux/brcm47xx/patches-3.14/141-MIPS-BCM47XX-add-detection-and-GPIO-config-for-Sieme.patch

@@ -0,0 +1,89 @@
+From c546fa49901252cbc1e4046d7188858b2f9e130f Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <[email protected]>
+Date: Fri, 10 Jan 2014 23:55:43 +0100
+Subject: [PATCH 2/2] MIPS: BCM47XX: add detection and GPIO config for Siemens
+ SE505v2
+
+This adds board detection for the Siemens SE505v2 and the led gpio
+configuration. This board does not have any buttons.
+This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
+
+Signed-off-by: Hauke Mehrtens <[email protected]>
+---
+ arch/mips/bcm47xx/board.c                          |   17 +++++++++++++++++
+ arch/mips/bcm47xx/leds.c                           |   12 ++++++++++++
+ arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h |    2 ++
+ 3 files changed, 31 insertions(+)
+
+--- a/arch/mips/bcm47xx/board.c
++++ b/arch/mips/bcm47xx/board.c
+@@ -181,6 +181,13 @@ struct bcm47xx_board_type_list3 bcm47xx_
+ 	{ {0}, NULL},
+ };
+ 
++/* boardtype, boardrev */
++static const
++struct bcm47xx_board_type_list2 bcm47xx_board_list_board_type_rev[] __initconst = {
++	{{BCM47XX_BOARD_SIEMENS_SE505V2, "Siemens SE505 V2"}, "0x0101", "0x10"},
++	{ {0}, NULL},
++};
++
+ static const
+ struct bcm47xx_board_type bcm47xx_board_unknown[] __initconst = {
+ 	{BCM47XX_BOARD_UNKNOWN, "Unknown Board"},
+@@ -274,6 +281,16 @@ static __init const struct bcm47xx_board
+ 				return &e3->board;
+ 		}
+ 	}
++
++	if (bcm47xx_nvram_getenv("boardtype", buf1, sizeof(buf1)) >= 0 &&
++	    bcm47xx_nvram_getenv("boardrev", buf2, sizeof(buf2)) >= 0 &&
++    	    bcm47xx_nvram_getenv("boardnum", buf3, sizeof(buf3)) ==  -ENOENT) {
++		for (e2 = bcm47xx_board_list_board_type_rev; e2->value1; e2++) {
++			if (!strcmp(buf1, e2->value1) &&
++			    !strcmp(buf2, e2->value2))
++				return &e2->board;
++		}
++	}
+ 	return bcm47xx_board_unknown;
+ }
+ 
+--- a/arch/mips/bcm47xx/leds.c
++++ b/arch/mips/bcm47xx/leds.c
+@@ -383,6 +383,14 @@ bcm47xx_leds_netgear_wnr834bv2[] __initc
+ 	BCM47XX_GPIO_LED(7, "unk", "connected", 0, LEDS_GPIO_DEFSTATE_OFF),
+ };
+ 
++/* Siemens */
++static const struct gpio_led
++bcm47xx_leds_siemens_se505v2[] __initconst = {
++	BCM47XX_GPIO_LED(0, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(3, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
++	BCM47XX_GPIO_LED(5, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
++};
++
+ /* SimpleTech */
+ 
+ static const struct gpio_led
+@@ -562,6 +570,10 @@ void __init bcm47xx_leds_register(void)
+ 		bcm47xx_set_pdata(bcm47xx_leds_netgear_wnr834bv2);
+ 		break;
+ 
++	case BCM47XX_BOARD_SIEMENS_SE505V2:
++		bcm47xx_set_pdata(bcm47xx_leds_siemens_se505v2);
++		break;
++
+ 	case BCM47XX_BOARD_SIMPLETECH_SIMPLESHARE:
+ 		bcm47xx_set_pdata(bcm47xx_leds_simpletech_simpleshare);
+ 		break;
+--- a/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
++++ b/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
+@@ -94,6 +94,8 @@ enum bcm47xx_board {
+ 
+ 	BCM47XX_BOARD_PHICOMM_M1,
+ 
++	BCM47XX_BOARD_SIEMENS_SE505V2,
++
+ 	BCM47XX_BOARD_SIMPLETECH_SIMPLESHARE,
+ 
+ 	BCM47XX_BOARD_ZTE_H218N,

target/linux/brcm47xx/patches-3.14/142-MIPS-BCM47XX-add-Belkin-F7Dxxxx-board-detection.patch

@@ -0,0 +1,77 @@
+From 44927df87162ae9beb6e7b934b0e75818b88e350 Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <[email protected]>
+Date: Thu, 2 Jan 2014 19:10:05 +0100
+Subject: [PATCH] MIPS: BCM47XX: add Belkin F7Dxxxx board detection
+
+From: Cody P Schafer <[email protected]>
+
+Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
+documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
+F7D4302 are reasonable guesses which are unlikely to cause
+mis-detection.
+
+Signed-off-by: Cody P Schafer <[email protected]>
+Signed-off-by: Hauke Mehrtens <[email protected]>
+---
+ arch/mips/bcm47xx/board.c                          |    4 ++++
+ arch/mips/bcm47xx/buttons.c                        |    4 ++++
+ arch/mips/bcm47xx/leds.c                           |    4 ++++
+ arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h |    4 ++++
+ 4 files changed, 16 insertions(+)
+
+--- a/arch/mips/bcm47xx/board.c
++++ b/arch/mips/bcm47xx/board.c
+@@ -71,7 +71,11 @@ struct bcm47xx_board_type_list1 bcm47xx_
+ 	{{BCM47XX_BOARD_ASUS_WL500W, "Asus WL500W"}, "WL500gW-"},
+ 	{{BCM47XX_BOARD_ASUS_WL520GC, "Asus WL520GC"}, "WL520GC-"},
+ 	{{BCM47XX_BOARD_ASUS_WL520GU, "Asus WL520GU"}, "WL520GU-"},
++	{{BCM47XX_BOARD_BELKIN_F7D3301, "Belkin F7D3301"}, "F7D3301"},
++	{{BCM47XX_BOARD_BELKIN_F7D3302, "Belkin F7D3302"}, "F7D3302"},
+ 	{{BCM47XX_BOARD_BELKIN_F7D4301, "Belkin F7D4301"}, "F7D4301"},
++	{{BCM47XX_BOARD_BELKIN_F7D4302, "Belkin F7D4302"}, "F7D4302"},
++	{{BCM47XX_BOARD_BELKIN_F7D4401, "Belkin F7D4401"}, "F7D4401"},
+ 	{ {0}, NULL},
+ };
+ 
+--- a/arch/mips/bcm47xx/buttons.c
++++ b/arch/mips/bcm47xx/buttons.c
+@@ -420,7 +420,11 @@ int __init bcm47xx_buttons_register(void
+ 		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wlhdd);
+ 		break;
+ 
++	case BCM47XX_BOARD_BELKIN_F7D3301:
++	case BCM47XX_BOARD_BELKIN_F7D3302:
+ 	case BCM47XX_BOARD_BELKIN_F7D4301:
++	case BCM47XX_BOARD_BELKIN_F7D4302:
++	case BCM47XX_BOARD_BELKIN_F7D4401:
+ 		err = bcm47xx_copy_bdata(bcm47xx_buttons_belkin_f7d4301);
+ 		break;
+ 
+--- a/arch/mips/bcm47xx/leds.c
++++ b/arch/mips/bcm47xx/leds.c
+@@ -457,7 +457,11 @@ void __init bcm47xx_leds_register(void)
+ 		bcm47xx_set_pdata(bcm47xx_leds_asus_wlhdd);
+ 		break;
+ 
++	case BCM47XX_BOARD_BELKIN_F7D3301:
++	case BCM47XX_BOARD_BELKIN_F7D3302:
+ 	case BCM47XX_BOARD_BELKIN_F7D4301:
++	case BCM47XX_BOARD_BELKIN_F7D4302:
++	case BCM47XX_BOARD_BELKIN_F7D4401:
+ 		bcm47xx_set_pdata(bcm47xx_leds_belkin_f7d4301);
+ 		break;
+ 
+--- a/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
++++ b/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
+@@ -27,7 +27,11 @@ enum bcm47xx_board {
+ 	BCM47XX_BOARD_ASUS_WL700GE,
+ 	BCM47XX_BOARD_ASUS_WLHDD,
+ 
++	BCM47XX_BOARD_BELKIN_F7D3301,
++	BCM47XX_BOARD_BELKIN_F7D3302,
+ 	BCM47XX_BOARD_BELKIN_F7D4301,
++	BCM47XX_BOARD_BELKIN_F7D4302,
++	BCM47XX_BOARD_BELKIN_F7D4401,
+ 
+ 	BCM47XX_BOARD_BUFFALO_WBR2_G54,
+ 	BCM47XX_BOARD_BUFFALO_WHR2_A54G54,

target/linux/brcm47xx/patches-3.14/150-cpu_fixes.patch

@@ -0,0 +1,373 @@
+--- a/arch/mips/include/asm/r4kcache.h
++++ b/arch/mips/include/asm/r4kcache.h
+@@ -18,6 +18,20 @@
+ #include <asm/cpu-type.h>
+ #include <asm/mipsmtregs.h>
+ 
++#ifdef CONFIG_BCM47XX
++#include <asm/paccess.h>
++#include <linux/ssb/ssb.h>
++#define BCM4710_DUMMY_RREG() ((void) *((u8 *) KSEG1ADDR(SSB_ENUM_BASE)))
++
++#define BCM4710_FILL_TLB(addr) (*(volatile unsigned long *)(addr))
++#define BCM4710_PROTECTED_FILL_TLB(addr) ({ unsigned long x; get_dbe(x, (volatile unsigned long *)(addr)); })
++#else
++#define BCM4710_DUMMY_RREG()
++
++#define BCM4710_FILL_TLB(addr)
++#define BCM4710_PROTECTED_FILL_TLB(addr)
++#endif
++
+ /*
+  * This macro return a properly sign-extended address suitable as base address
+  * for indexed cache operations.  Two issues here:
+@@ -151,6 +165,7 @@ static inline void flush_icache_line_ind
+ static inline void flush_dcache_line_indexed(unsigned long addr)
+ {
+ 	__dflush_prologue
++	BCM4710_DUMMY_RREG();
+ 	cache_op(Index_Writeback_Inv_D, addr);
+ 	__dflush_epilogue
+ }
+@@ -178,6 +193,7 @@ static inline void flush_icache_line(uns
+ static inline void flush_dcache_line(unsigned long addr)
+ {
+ 	__dflush_prologue
++	BCM4710_DUMMY_RREG();
+ 	cache_op(Hit_Writeback_Inv_D, addr);
+ 	__dflush_epilogue
+ }
+@@ -185,6 +201,7 @@ static inline void flush_dcache_line(uns
+ static inline void invalidate_dcache_line(unsigned long addr)
+ {
+ 	__dflush_prologue
++	BCM4710_DUMMY_RREG();
+ 	cache_op(Hit_Invalidate_D, addr);
+ 	__dflush_epilogue
+ }
+@@ -223,6 +240,7 @@ static inline void protected_flush_icach
+ 		break;
+ 
+ 	default:
++		BCM4710_DUMMY_RREG();
+ 		protected_cache_op(Hit_Invalidate_I, addr);
+ 		break;
+ 	}
+@@ -236,6 +254,7 @@ static inline void protected_flush_icach
+  */
+ static inline void protected_writeback_dcache_line(unsigned long addr)
+ {
++	BCM4710_DUMMY_RREG();
+ 	protected_cache_op(Hit_Writeback_Inv_D, addr);
+ }
+ 
+@@ -356,8 +375,51 @@ static inline void invalidate_tcache_pag
+ 		: "r" (base),						\
+ 		  "i" (op));
+ 
++static inline void blast_dcache(void)
++{
++	unsigned long start = KSEG0;
++	unsigned long dcache_size = current_cpu_data.dcache.waysize * current_cpu_data.dcache.ways;
++	unsigned long end = (start + dcache_size);
++
++	do {
++		BCM4710_DUMMY_RREG();
++		cache_op(Index_Writeback_Inv_D, start);
++		start += current_cpu_data.dcache.linesz;
++	} while(start < end);
++}
++
++static inline void blast_dcache_page(unsigned long page)
++{
++	unsigned long start = page;
++	unsigned long end = start + PAGE_SIZE;
++
++	BCM4710_FILL_TLB(start);
++	do {
++		BCM4710_DUMMY_RREG();
++		cache_op(Hit_Writeback_Inv_D, start);
++		start += current_cpu_data.dcache.linesz;
++	} while(start < end);
++}
++
++static inline void blast_dcache_page_indexed(unsigned long page)
++{
++	unsigned long start = page;
++	unsigned long end = start + PAGE_SIZE;
++	unsigned long ws_inc = 1UL << current_cpu_data.dcache.waybit;
++	unsigned long ws_end = current_cpu_data.dcache.ways <<
++	                       current_cpu_data.dcache.waybit;
++	unsigned long ws, addr;
++	for (ws = 0; ws < ws_end; ws += ws_inc) {
++		start = page + ws;
++		for (addr = start; addr < end; addr += current_cpu_data.dcache.linesz) {
++			BCM4710_DUMMY_RREG();
++			cache_op(Index_Writeback_Inv_D, addr);
++		}
++	}
++}
++
+ /* build blast_xxx, blast_xxx_page, blast_xxx_page_indexed */
+-#define __BUILD_BLAST_CACHE(pfx, desc, indexop, hitop, lsize, extra)	\
++#define __BUILD_BLAST_CACHE(pfx, desc, indexop, hitop, lsize, extra, war) \
+ static inline void extra##blast_##pfx##cache##lsize(void)		\
+ {									\
+ 	unsigned long start = INDEX_BASE;				\
+@@ -369,6 +431,7 @@ static inline void extra##blast_##pfx##c
+ 									\
+ 	__##pfx##flush_prologue						\
+ 									\
++	war								\
+ 	for (ws = 0; ws < ws_end; ws += ws_inc)				\
+ 		for (addr = start; addr < end; addr += lsize * 32)	\
+ 			cache##lsize##_unroll32(addr|ws, indexop);	\
+@@ -383,6 +446,7 @@ static inline void extra##blast_##pfx##c
+ 									\
+ 	__##pfx##flush_prologue						\
+ 									\
++	war								\
+ 	do {								\
+ 		cache##lsize##_unroll32(start, hitop);			\
+ 		start += lsize * 32;					\
+@@ -401,6 +465,8 @@ static inline void extra##blast_##pfx##c
+ 			       current_cpu_data.desc.waybit;		\
+ 	unsigned long ws, addr;						\
+ 									\
++	war								\
++									\
+ 	__##pfx##flush_prologue						\
+ 									\
+ 	for (ws = 0; ws < ws_end; ws += ws_inc)				\
+@@ -410,37 +476,40 @@ static inline void extra##blast_##pfx##c
+ 	__##pfx##flush_epilogue						\
+ }
+ 
+-__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 16, )
+-__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 16, )
+-__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16, )
+-__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 32, )
+-__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 32, )
+-__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I_Loongson2, 32, loongson2_)
+-__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32, )
+-__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 64, )
+-__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 64, )
+-__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64, )
+-__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128, )
+-
+-__BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 16, )
+-__BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 32, )
+-__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 16, )
+-__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 32, )
+-__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 64, )
+-__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 128, )
++__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 16, , )
++__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 16, , BCM4710_FILL_TLB(start);)
++__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16, , )
++__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 32, , )
++__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 32, , BCM4710_FILL_TLB(start);)
++__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I_Loongson2, 32, loongson2_, BCM4710_FILL_TLB(start);)
++__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32, , )
++__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 64, , )
++__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 64, , BCM4710_FILL_TLB(start);)
++__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64, , )
++__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128, , )
++
++__BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 16, , )
++__BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 32, , )
++__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 16, , )
++__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 32, , )
++__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 64, , )
++__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 128, , )
++
+ 
+ /* build blast_xxx_range, protected_blast_xxx_range */
+-#define __BUILD_BLAST_CACHE_RANGE(pfx, desc, hitop, prot, extra)	\
++#define __BUILD_BLAST_CACHE_RANGE(pfx, desc, hitop, prot, extra, war, war2)	\
+ static inline void prot##extra##blast_##pfx##cache##_range(unsigned long start, \
+ 						    unsigned long end)	\
+ {									\
+ 	unsigned long lsize = cpu_##desc##_line_size();			\
+ 	unsigned long addr = start & ~(lsize - 1);			\
+ 	unsigned long aend = (end - 1) & ~(lsize - 1);			\
++	war								\
+ 									\
+ 	__##pfx##flush_prologue						\
+ 									\
+ 	while (1) {							\
++		war2						\
+ 		prot##cache_op(hitop, addr);				\
+ 		if (addr == aend)					\
+ 			break;						\
+@@ -450,15 +519,15 @@ static inline void prot##extra##blast_##
+ 	__##pfx##flush_epilogue						\
+ }
+ 
+-__BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, protected_, )
+-__BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, protected_, )
+-__BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I, protected_, )
++__BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, protected_, , BCM4710_PROTECTED_FILL_TLB(addr); BCM4710_PROTECTED_FILL_TLB(aend);, BCM4710_DUMMY_RREG();)
++__BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, protected_, , , )
++__BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I, protected_, , , )
+ __BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I_Loongson2, \
+-	protected_, loongson2_)
+-__BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, , )
+-__BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, , )
++	protected_, loongson2_, , )
++__BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, , , BCM4710_FILL_TLB(addr); BCM4710_FILL_TLB(aend);, BCM4710_DUMMY_RREG();)
++__BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, , , , )
+ /* blast_inv_dcache_range */
+-__BUILD_BLAST_CACHE_RANGE(inv_d, dcache, Hit_Invalidate_D, , )
+-__BUILD_BLAST_CACHE_RANGE(inv_s, scache, Hit_Invalidate_SD, , )
++__BUILD_BLAST_CACHE_RANGE(inv_d, dcache, Hit_Invalidate_D, , , , BCM4710_DUMMY_RREG();)
++__BUILD_BLAST_CACHE_RANGE(inv_s, scache, Hit_Invalidate_SD, , , , )
+ 
+ #endif /* _ASM_R4KCACHE_H */
+--- a/arch/mips/include/asm/stackframe.h
++++ b/arch/mips/include/asm/stackframe.h
+@@ -436,6 +436,10 @@
+ 		.macro	RESTORE_SP_AND_RET
+ 		LONG_L	sp, PT_R29(sp)
+ 		.set	mips3
++#ifdef CONFIG_BCM47XX
++		nop
++		nop
++#endif
+ 		eret
+ 		.set	mips0
+ 		.endm
+--- a/arch/mips/kernel/genex.S
++++ b/arch/mips/kernel/genex.S
+@@ -46,6 +46,10 @@
+ NESTED(except_vec3_generic, 0, sp)
+ 	.set	push
+ 	.set	noat
++#ifdef CONFIG_BCM47XX
++	nop
++	nop
++#endif
+ #if R5432_CP0_INTERRUPT_WAR
+ 	mfc0	k0, CP0_INDEX
+ #endif
+--- a/arch/mips/mm/c-r4k.c
++++ b/arch/mips/mm/c-r4k.c
+@@ -37,6 +37,9 @@
+ #include <asm/traps.h>
+ #include <asm/dma-coherence.h>
+ 
++/* For enabling BCM4710 cache workarounds */
++int bcm4710 = 0;
++
+ /*
+  * Special Variant of smp_call_function for use by cache functions:
+  *
+@@ -113,6 +116,9 @@ static void r4k_blast_dcache_page_setup(
+ {
+ 	unsigned long  dc_lsize = cpu_dcache_line_size();
+ 
++	if (bcm4710)
++		r4k_blast_dcache_page = blast_dcache_page;
++	else
+ 	if (dc_lsize == 0)
+ 		r4k_blast_dcache_page = (void *)cache_noop;
+ 	else if (dc_lsize == 16)
+@@ -129,6 +135,9 @@ static void r4k_blast_dcache_page_indexe
+ {
+ 	unsigned long dc_lsize = cpu_dcache_line_size();
+ 
++	if (bcm4710)
++		r4k_blast_dcache_page_indexed = blast_dcache_page_indexed;
++	else
+ 	if (dc_lsize == 0)
+ 		r4k_blast_dcache_page_indexed = (void *)cache_noop;
+ 	else if (dc_lsize == 16)
+@@ -146,6 +155,9 @@ static void r4k_blast_dcache_setup(void)
+ {
+ 	unsigned long dc_lsize = cpu_dcache_line_size();
+ 
++	if (bcm4710)
++		r4k_blast_dcache = blast_dcache;
++	else
+ 	if (dc_lsize == 0)
+ 		r4k_blast_dcache = (void *)cache_noop;
+ 	else if (dc_lsize == 16)
+@@ -703,6 +715,8 @@ static void local_r4k_flush_cache_sigtra
+ 	unsigned long addr = (unsigned long) arg;
+ 
+ 	R4600_HIT_CACHEOP_WAR_IMPL;
++	BCM4710_PROTECTED_FILL_TLB(addr);
++	BCM4710_PROTECTED_FILL_TLB(addr + 4);
+ 	if (dc_lsize)
+ 		protected_writeback_dcache_line(addr & ~(dc_lsize - 1));
+ 	if (!cpu_icache_snoops_remote_store && scache_size)
+@@ -1403,6 +1417,17 @@ static void coherency_setup(void)
+ 	 * silly idea of putting something else there ...
+ 	 */
+ 	switch (current_cpu_type()) {
++	case CPU_BMIPS3300:
++		{
++			u32 cm;
++			cm = read_c0_diag();
++			/* Enable icache */
++			cm |= (1 << 31);
++			/* Enable dcache */
++			cm |= (1 << 30);
++			write_c0_diag(cm);
++		}
++		break;
+ 	case CPU_R4000PC:
+ 	case CPU_R4000SC:
+ 	case CPU_R4000MC:
+@@ -1449,6 +1474,15 @@ void r4k_cache_init(void)
+ 	extern void build_copy_page(void);
+ 	struct cpuinfo_mips *c = &current_cpu_data;
+ 
++	/* Check if special workarounds are required */
++#ifdef CONFIG_BCM47XX
++	if (current_cpu_data.cputype == CPU_BMIPS32 && (current_cpu_data.processor_id & 0xff) == 0) {
++		printk("Enabling BCM4710A0 cache workarounds.\n");
++		bcm4710 = 1;
++	} else
++#endif
++		bcm4710 = 0;
++
+ 	probe_pcache();
+ 	setup_scache();
+ 
+@@ -1514,6 +1548,14 @@ void r4k_cache_init(void)
+ 	 */
+ 	local_r4k___flush_cache_all(NULL);
+ 
++#ifdef CONFIG_BCM47XX
++	{
++		static void (*_coherency_setup)(void);
++		_coherency_setup = (void (*)(void)) KSEG1ADDR(coherency_setup);
++		_coherency_setup();
++	}
++#else
+ 	coherency_setup();
++#endif
+ 	board_cache_error_setup = r4k_cache_error_setup;
+ }
+--- a/arch/mips/mm/tlbex.c
++++ b/arch/mips/mm/tlbex.c
+@@ -1277,6 +1277,9 @@ static void build_r4000_tlb_refill_handl
+ 			/* No need for uasm_i_nop */
+ 		}
+ 
++#ifdef CONFIG_BCM47XX
++		uasm_i_nop(&p);
++#endif
+ #ifdef CONFIG_64BIT
+ 		build_get_pmde64(&p, &l, &r, K0, K1); /* get pmd in K1 */
+ #else
+@@ -1835,6 +1838,9 @@ build_r4000_tlbchange_handler_head(u32 *
+ {
+ 	struct work_registers wr = build_get_work_registers(p);
+ 
++#ifdef CONFIG_BCM47XX
++	uasm_i_nop(p);
++#endif
+ #ifdef CONFIG_64BIT
+ 	build_get_pmde64(p, l, r, wr.r1, wr.r2); /* get pmd in ptr */
+ #else

target/linux/brcm47xx/patches-3.14/160-kmap_coherent.patch

@@ -0,0 +1,70 @@
+--- a/arch/mips/include/asm/cpu-features.h
++++ b/arch/mips/include/asm/cpu-features.h
+@@ -133,6 +133,9 @@
+ #ifndef cpu_has_local_ebase
+ #define cpu_has_local_ebase	1
+ #endif
++#ifndef cpu_use_kmap_coherent
++#define cpu_use_kmap_coherent 1
++#endif
+ 
+ /*
+  * I-Cache snoops remote store.	 This only matters on SMP.  Some multiprocessors
+--- a/arch/mips/include/asm/mach-bcm47xx/cpu-feature-overrides.h
++++ b/arch/mips/include/asm/mach-bcm47xx/cpu-feature-overrides.h
+@@ -79,4 +79,6 @@
+ #define cpu_scache_line_size()		0
+ #define cpu_has_vz			0
+ 
++#define cpu_use_kmap_coherent		0
++
+ #endif /* __ASM_MACH_BCM47XX_CPU_FEATURE_OVERRIDES_H */
+--- a/arch/mips/mm/c-r4k.c
++++ b/arch/mips/mm/c-r4k.c
+@@ -523,7 +523,7 @@ static inline void local_r4k_flush_cache
+ 		 */
+ 		map_coherent = (cpu_has_dc_aliases &&
+ 				page_mapped(page) && !Page_dcache_dirty(page));
+-		if (map_coherent)
++		if (map_coherent && cpu_use_kmap_coherent)
+ 			vaddr = kmap_coherent(page, addr);
+ 		else
+ 			vaddr = kmap_atomic(page);
+@@ -546,7 +546,7 @@ static inline void local_r4k_flush_cache
+ 	}
+ 
+ 	if (vaddr) {
+-		if (map_coherent)
++		if (map_coherent && cpu_use_kmap_coherent)
+ 			kunmap_coherent();
+ 		else
+ 			kunmap_atomic(vaddr);
+--- a/arch/mips/mm/init.c
++++ b/arch/mips/mm/init.c
+@@ -200,7 +200,7 @@ void copy_user_highpage(struct page *to,
+ 	void *vfrom, *vto;
+ 
+ 	vto = kmap_atomic(to);
+-	if (cpu_has_dc_aliases &&
++	if (cpu_has_dc_aliases && cpu_use_kmap_coherent &&
+ 	    page_mapped(from) && !Page_dcache_dirty(from)) {
+ 		vfrom = kmap_coherent(from, vaddr);
+ 		copy_page(vto, vfrom);
+@@ -222,7 +222,7 @@ void copy_to_user_page(struct vm_area_st
+ 	struct page *page, unsigned long vaddr, void *dst, const void *src,
+ 	unsigned long len)
+ {
+-	if (cpu_has_dc_aliases &&
++	if (cpu_has_dc_aliases && cpu_use_kmap_coherent &&
+ 	    page_mapped(page) && !Page_dcache_dirty(page)) {
+ 		void *vto = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
+ 		memcpy(vto, src, len);
+@@ -240,7 +240,7 @@ void copy_from_user_page(struct vm_area_
+ 	struct page *page, unsigned long vaddr, void *dst, const void *src,
+ 	unsigned long len)
+ {
+-	if (cpu_has_dc_aliases &&
++	if (cpu_has_dc_aliases && cpu_use_kmap_coherent &&
+ 	    page_mapped(page) && !Page_dcache_dirty(page)) {
+ 		void *vfrom = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
+ 		memcpy(dst, vfrom, len);

target/linux/brcm47xx/patches-3.14/209-b44-register-adm-switch.patch

@@ -0,0 +1,102 @@
+From b36f694256f41bc71571f467646d015dda128d14 Mon Sep 17 00:00:00 2001
+From: Hauke Mehrtens <[email protected]>
+Date: Sat, 9 Nov 2013 17:03:59 +0100
+Subject: [PATCH 210/210] b44: register adm switch
+
+---
+ drivers/net/ethernet/broadcom/b44.c |   57 +++++++++++++++++++++++++++++++++++
+ drivers/net/ethernet/broadcom/b44.h |    3 ++
+ 2 files changed, 60 insertions(+)
+
+--- a/drivers/net/ethernet/broadcom/b44.c
++++ b/drivers/net/ethernet/broadcom/b44.c
+@@ -31,6 +31,8 @@
+ #include <linux/ssb/ssb.h>
+ #include <linux/slab.h>
+ #include <linux/phy.h>
++#include <linux/platform_device.h>
++#include <linux/platform_data/adm6996-gpio.h>
+ 
+ #include <asm/uaccess.h>
+ #include <asm/io.h>
+@@ -2239,6 +2241,58 @@ static void b44_adjust_link(struct net_d
+ 	}
+ }
+ 
++#ifdef CONFIG_BCM47XX
++static struct adm6996_gpio_platform_data b44_adm_data = {
++	.eecs	= 2,
++	.eesk	= 3,
++	.eedi	= 4,
++	.eerc	= 5,
++	.model	= ADM6996L,
++};
++
++static struct platform_device b44_adm_dev = {
++	.name		= "adm6996_gpio",
++	.id		= -1,
++	.dev		= {
++		.platform_data = &b44_adm_data,
++	},
++};
++
++static int b44_register_adm_switch(struct b44 *bp)
++{
++	int gpio;
++	int err;
++
++	gpio = bcm47xx_nvram_gpio_pin("adm_eecs");
++	if (gpio >= 0)
++		b44_adm_data.eecs = gpio;
++
++	gpio = bcm47xx_nvram_gpio_pin("adm_eesk");
++	if (gpio >= 0)
++		b44_adm_data.eesk = gpio;
++
++	gpio = bcm47xx_nvram_gpio_pin("adm_eedi");
++	if (gpio >= 0)
++		b44_adm_data.eedi = gpio;
++
++	gpio = bcm47xx_nvram_gpio_pin("adm_rc");
++	if (gpio >= 0)
++		b44_adm_data.eerc = gpio;
++
++	if (!bp->adm_switch) {
++		err = platform_device_register(&b44_adm_dev);
++		if (!err)
++			bp->adm_switch = &b44_adm_dev;
++	}
++	return err;
++}
++#else
++static int b44_register_adm_switch(struct b44 *bp)
++{
++	return 0;
++}
++#endif /* CONFIG_BCM47XX */
++
+ static int b44_register_phy_one(struct b44 *bp)
+ {
+ 	struct mii_bus *mii_bus;
+@@ -2282,6 +2336,9 @@ static int b44_register_phy_one(struct b
+ 	if (!bp->mii_bus->phy_map[bp->phy_addr] &&
+ 	    (sprom->boardflags_lo & (B44_BOARDFLAG_ROBO | B44_BOARDFLAG_ADM))) {
+ 
++		if (sprom->boardflags_lo & B44_BOARDFLAG_ADM)
++			b44_register_adm_switch(bp);
++
+ 		dev_info(sdev->dev,
+ 			 "could not find PHY at %i, use fixed one\n",
+ 			 bp->phy_addr);
+--- a/drivers/net/ethernet/broadcom/b44.h
++++ b/drivers/net/ethernet/broadcom/b44.h
+@@ -404,6 +404,9 @@ struct b44 {
+ 	struct mii_bus		*mii_bus;
+ 	int			old_link;
+ 	struct mii_if_info	mii_if;
++
++	/* platform device for associated switch */
++	struct platform_device *adm_switch;
+ };
+ 
+ #endif /* _B44_H */

target/linux/brcm47xx/patches-3.14/210-b44_phy_fix.patch

@@ -0,0 +1,54 @@
+--- a/drivers/net/ethernet/broadcom/b44.c
++++ b/drivers/net/ethernet/broadcom/b44.c
+@@ -431,10 +431,34 @@ static void b44_wap54g10_workaround(stru
+ error:
+ 	pr_warning("PHY: cannot reset MII transceiver isolate bit\n");
+ }
++
++static void b44_bcm47xx_workarounds(struct b44 *bp)
++{
++	char buf[20];
++	struct ssb_device *sdev = bp->sdev;
++
++	/* Toshiba WRC-1000, Siemens SE505 v1, Askey RT-210W, RT-220W */
++	if (sdev->bus->sprom.board_num == 100) {
++		bp->phy_addr = B44_PHY_ADDR_NO_LOCAL_PHY;
++	} else {
++		/* WL-HDD */
++		if (bcm47xx_nvram_getenv("hardware_version", buf, sizeof(buf)) >= 0 &&
++		    !strncmp(buf, "WL300-", strlen("WL300-"))) {
++			if (sdev->bus->sprom.et0phyaddr == 0 &&
++			    sdev->bus->sprom.et1phyaddr == 1)
++				bp->phy_addr = B44_PHY_ADDR_NO_LOCAL_PHY;
++		}
++	}
++	return;
++}
+ #else
+ static inline void b44_wap54g10_workaround(struct b44 *bp)
+ {
+ }
++
++static inline void b44_bcm47xx_workarounds(struct b44 *bp)
++{
++}
+ #endif
+ 
+ static int b44_setup_phy(struct b44 *bp)
+@@ -443,6 +467,7 @@ static int b44_setup_phy(struct b44 *bp)
+ 	int err;
+ 
+ 	b44_wap54g10_workaround(bp);
++	b44_bcm47xx_workarounds(bp);
+ 
+ 	if (bp->flags & B44_FLAG_EXTERNAL_PHY)
+ 		return 0;
+@@ -2169,6 +2194,8 @@ static int b44_get_invariants(struct b44
+ 	 * valid PHY address. */
+ 	bp->phy_addr &= 0x1F;
+ 
++	b44_bcm47xx_workarounds(bp);
++
+ 	memcpy(bp->dev->dev_addr, addr, ETH_ALEN);
+ 
+ 	if (!is_valid_ether_addr(&bp->dev->dev_addr[0])){

target/linux/brcm47xx/patches-3.14/280-activate_ssb_support_in_usb.patch

@@ -0,0 +1,25 @@
+This prevents the options from being delete with make kernel_oldconfig.
+---
+ drivers/ssb/Kconfig |    2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/bcma/Kconfig
++++ b/drivers/bcma/Kconfig
+@@ -38,6 +38,7 @@ config BCMA_DRIVER_PCI_HOSTMODE
+ config BCMA_HOST_SOC
+ 	bool "Support for BCMA in a SoC"
+ 	depends on BCMA
++	select USB_HCD_BCMA if USB_EHCI_HCD || USB_OHCI_HCD
+ 	help
+ 	  Host interface for a Broadcom AIX bus directly mapped into
+ 	  the memory. This only works with the Broadcom SoCs from the
+--- a/drivers/ssb/Kconfig
++++ b/drivers/ssb/Kconfig
+@@ -146,6 +146,7 @@ config SSB_SFLASH
+ config SSB_EMBEDDED
+ 	bool
+ 	depends on SSB_DRIVER_MIPS && SSB_PCICORE_HOSTMODE
++	select USB_HCD_SSB if USB_EHCI_HCD || USB_OHCI_HCD
+ 	default y
+ 
+ config SSB_DRIVER_EXTIF

target/linux/brcm47xx/patches-3.14/300-fork_cacheflush.patch

@@ -0,0 +1,11 @@
+--- a/arch/mips/include/asm/cacheflush.h
++++ b/arch/mips/include/asm/cacheflush.h
+@@ -32,7 +32,7 @@
+ extern void (*flush_cache_all)(void);
+ extern void (*__flush_cache_all)(void);
+ extern void (*flush_cache_mm)(struct mm_struct *mm);
+-#define flush_cache_dup_mm(mm)	do { (void) (mm); } while (0)
++#define flush_cache_dup_mm(mm) flush_cache_mm(mm)
+ extern void (*flush_cache_range)(struct vm_area_struct *vma,
+ 	unsigned long start, unsigned long end);
+ extern void (*flush_cache_page)(struct vm_area_struct *vma, unsigned long page, unsigned long pfn);

target/linux/brcm47xx/patches-3.14/310-no_highpage.patch

@@ -0,0 +1,66 @@
+--- a/arch/mips/include/asm/page.h
++++ b/arch/mips/include/asm/page.h
+@@ -71,6 +71,7 @@ static inline unsigned int page_size_ftl
+ #endif /* CONFIG_MIPS_HUGE_TLB_SUPPORT */
+ 
+ #include <linux/pfn.h>
++#include <asm/cpu-features.h>
+ 
+ extern void build_clear_page(void);
+ extern void build_copy_page(void);
+@@ -105,13 +106,16 @@ static inline void clear_user_page(void
+ 		flush_data_cache_page((unsigned long)addr);
+ }
+ 
+-extern void copy_user_page(void *vto, void *vfrom, unsigned long vaddr,
+-	struct page *to);
+-struct vm_area_struct;
+-extern void copy_user_highpage(struct page *to, struct page *from,
+-	unsigned long vaddr, struct vm_area_struct *vma);
++static inline void copy_user_page(void *vto, void *vfrom, unsigned long vaddr,
++	struct page *to)
++{
++	extern void (*flush_data_cache_page)(unsigned long addr);
+ 
+-#define __HAVE_ARCH_COPY_USER_HIGHPAGE
++	copy_page(vto, vfrom);
++	if (!cpu_has_ic_fills_f_dc ||
++	    pages_do_alias((unsigned long)vto, vaddr & PAGE_MASK))
++		flush_data_cache_page((unsigned long)vto);
++}
+ 
+ /*
+  * These are used to make use of C type-checking..
+--- a/arch/mips/mm/init.c
++++ b/arch/mips/mm/init.c
+@@ -194,30 +194,6 @@ void kunmap_coherent(void)
+ 	pagefault_enable();
+ }
+ 
+-void copy_user_highpage(struct page *to, struct page *from,
+-	unsigned long vaddr, struct vm_area_struct *vma)
+-{
+-	void *vfrom, *vto;
+-
+-	vto = kmap_atomic(to);
+-	if (cpu_has_dc_aliases && cpu_use_kmap_coherent &&
+-	    page_mapped(from) && !Page_dcache_dirty(from)) {
+-		vfrom = kmap_coherent(from, vaddr);
+-		copy_page(vto, vfrom);
+-		kunmap_coherent();
+-	} else {
+-		vfrom = kmap_atomic(from);
+-		copy_page(vto, vfrom);
+-		kunmap_atomic(vfrom);
+-	}
+-	if ((!cpu_has_ic_fills_f_dc) ||
+-	    pages_do_alias((unsigned long)vto, vaddr & PAGE_MASK))
+-		flush_data_cache_page((unsigned long)vto);
+-	kunmap_atomic(vto);
+-	/* Make sure this page is cleared on other CPU's too before using it */
+-	smp_wmb();
+-}
+-
+ void copy_to_user_page(struct vm_area_struct *vma,
+ 	struct page *page, unsigned long vaddr, void *dst, const void *src,
+ 	unsigned long len)

target/linux/brcm47xx/patches-3.14/610-pci_ide_fix.patch

@@ -0,0 +1,14 @@
+--- a/include/linux/ide.h
++++ b/include/linux/ide.h
+@@ -191,7 +191,11 @@ static inline void ide_std_init_ports(st
+ 	hw->io_ports.ctl_addr = ctl_addr;
+ }
+ 
++#if defined CONFIG_BCM47XX
++# define MAX_HWIFS	2
++#else
+ #define MAX_HWIFS	10
++#endif
+ 
+ /*
+  * Now for the data we need to maintain per-drive:  ide_drive_t

target/linux/brcm47xx/patches-3.14/820-wgt634u-nvram-fix.patch

@@ -0,0 +1,296 @@
+The Netgear wgt634u uses a different format for storing the 
+configuration. This patch is needed to read out the correct 
+configuration. The cfe_env.c file uses a different method way to read 
+out the configuration than the in kernel cfe config reader.
+
+--- a/arch/mips/bcm47xx/Makefile
++++ b/arch/mips/bcm47xx/Makefile
+@@ -5,3 +5,4 @@
+ 
+ obj-y				+= irq.o nvram.o prom.o serial.o setup.o time.o sprom.o
+ obj-y				+= board.o buttons.o leds.o workarounds.o
++obj-y				+= cfe_env.o
+--- /dev/null
++++ b/arch/mips/bcm47xx/cfe_env.c
+@@ -0,0 +1,229 @@
++/*
++ * CFE environment variable access
++ *
++ * Copyright 2001-2003, Broadcom Corporation
++ * Copyright 2006, Felix Fietkau <[email protected]>
++ * 
++ * This program is free software; you can redistribute  it and/or modify it
++ * under  the terms of  the GNU General  Public License as published by the
++ * Free Software Foundation;  either version 2 of the  License, or (at your
++ * option) any later version.
++ */
++
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/kernel.h>
++#include <linux/string.h>
++#include <asm/io.h>
++#include <asm/uaccess.h>
++
++#define NVRAM_SIZE       (0x1ff0)
++static char _nvdata[NVRAM_SIZE];
++static char _valuestr[256];
++
++/*
++ * TLV types.  These codes are used in the "type-length-value"
++ * encoding of the items stored in the NVRAM device (flash or EEPROM)
++ *
++ * The layout of the flash/nvram is as follows:
++ *
++ * <type> <length> <data ...> <type> <length> <data ...> <type_end>
++ *
++ * The type code of "ENV_TLV_TYPE_END" marks the end of the list.
++ * The "length" field marks the length of the data section, not
++ * including the type and length fields.
++ *
++ * Environment variables are stored as follows:
++ *
++ * <type_env> <length> <flags> <name> = <value>
++ *
++ * If bit 0 (low bit) is set, the length is an 8-bit value.
++ * If bit 0 (low bit) is clear, the length is a 16-bit value
++ * 
++ * Bit 7 set indicates "user" TLVs.  In this case, bit 0 still
++ * indicates the size of the length field.  
++ *
++ * Flags are from the constants below:
++ *
++ */
++#define ENV_LENGTH_16BITS	0x00	/* for low bit */
++#define ENV_LENGTH_8BITS	0x01
++
++#define ENV_TYPE_USER		0x80
++
++#define ENV_CODE_SYS(n,l) (((n)<<1)|(l))
++#define ENV_CODE_USER(n,l) ((((n)<<1)|(l)) | ENV_TYPE_USER)
++
++/*
++ * The actual TLV types we support
++ */
++
++#define ENV_TLV_TYPE_END	0x00	
++#define ENV_TLV_TYPE_ENV	ENV_CODE_SYS(0,ENV_LENGTH_8BITS)
++
++/*
++ * Environment variable flags 
++ */
++
++#define ENV_FLG_NORMAL		0x00	/* normal read/write */
++#define ENV_FLG_BUILTIN		0x01	/* builtin - not stored in flash */
++#define ENV_FLG_READONLY	0x02	/* read-only - cannot be changed */
++
++#define ENV_FLG_MASK		0xFF	/* mask of attributes we keep */
++#define ENV_FLG_ADMIN		0x100	/* lets us internally override permissions */
++
++
++/*  *********************************************************************
++    *  _nvram_read(buffer,offset,length)
++    *  
++    *  Read data from the NVRAM device
++    *  
++    *  Input parameters: 
++    *  	   buffer - destination buffer
++    *  	   offset - offset of data to read
++    *  	   length - number of bytes to read
++    *  	   
++    *  Return value:
++    *  	   number of bytes read, or <0 if error occured
++    ********************************************************************* */
++static int
++_nvram_read(unsigned char *nv_buf, unsigned char *buffer, int offset, int length)
++{
++    int i;
++    if (offset > NVRAM_SIZE)
++	return -1; 
++
++    for ( i = 0; i < length; i++) {
++	buffer[i] = ((volatile unsigned char*)nv_buf)[offset + i];
++    }
++    return length;
++}
++
++
++static char*
++_strnchr(const char *dest,int c,size_t cnt)
++{
++	while (*dest && (cnt > 0)) {
++	if (*dest == c) return (char *) dest;
++	dest++;
++	cnt--;
++	}
++	return NULL;
++}
++
++
++
++/*
++ * Core support API: Externally visible.
++ */
++
++/*
++ * Get the value of an NVRAM variable
++ * @param	name	name of variable to get
++ * @return	value of variable or NULL if undefined
++ */
++
++char* 
++cfe_env_get(unsigned char *nv_buf, char* name)
++{
++    int size;
++    unsigned char *buffer;
++    unsigned char *ptr;
++    unsigned char *envval;
++    unsigned int reclen;
++    unsigned int rectype;
++    int offset;
++    int flg;
++    
++	if (!strcmp(name, "nvram_type"))
++		return "cfe";
++	
++    size = NVRAM_SIZE;
++    buffer = &_nvdata[0];
++
++    ptr = buffer;
++    offset = 0;
++
++    /* Read the record type and length */
++    if (_nvram_read(nv_buf, ptr,offset,1) != 1) {
++	goto error;
++    }
++    
++    while ((*ptr != ENV_TLV_TYPE_END)  && (size > 1)) {
++
++	/* Adjust pointer for TLV type */
++	rectype = *(ptr);
++	offset++;
++	size--;
++
++	/* 
++	 * Read the length.  It can be either 1 or 2 bytes
++	 * depending on the code 
++	 */
++	if (rectype & ENV_LENGTH_8BITS) {
++	    /* Read the record type and length - 8 bits */
++	    if (_nvram_read(nv_buf, ptr,offset,1) != 1) {
++		goto error;
++	    }
++	    reclen = *(ptr);
++	    size--;
++	    offset++;
++	}
++	else {
++	    /* Read the record type and length - 16 bits, MSB first */
++	    if (_nvram_read(nv_buf, ptr,offset,2) != 2) {
++		goto error;
++	    }
++	    reclen = (((unsigned int) *(ptr)) << 8) + (unsigned int) *(ptr+1);
++	    size -= 2;
++	    offset += 2;
++	}
++
++	if (reclen > size)
++	    break;	/* should not happen, bad NVRAM */
++
++	switch (rectype) {
++	    case ENV_TLV_TYPE_ENV:
++		/* Read the TLV data */
++		if (_nvram_read(nv_buf, ptr,offset,reclen) != reclen)
++		    goto error;
++		flg = *ptr++;
++		envval = (unsigned char *) _strnchr(ptr,'=',(reclen-1));
++		if (envval) {
++		    *envval++ = '\0';
++		    memcpy(_valuestr,envval,(reclen-1)-(envval-ptr));
++		    _valuestr[(reclen-1)-(envval-ptr)] = '\0';
++#if 0			
++		    printk(KERN_INFO "NVRAM:%s=%s\n", ptr, _valuestr);
++#endif
++		    if(!strcmp(ptr, name)){
++			return _valuestr;
++		    }
++		    if((strlen(ptr) > 1) && !strcmp(&ptr[1], name))
++			return _valuestr;
++		}
++		break;
++		
++	    default: 
++		/* Unknown TLV type, skip it. */
++		break;
++	    }
++
++	/*
++	 * Advance to next TLV 
++	 */
++		
++	size -= (int)reclen;
++	offset += reclen;
++
++	/* Read the next record type */
++	ptr = buffer;
++	if (_nvram_read(nv_buf, ptr,offset,1) != 1)
++	    goto error;
++	}
++
++error:
++    return NULL;
++
++}
++
+--- a/arch/mips/bcm47xx/nvram.c
++++ b/arch/mips/bcm47xx/nvram.c
+@@ -22,6 +22,8 @@
+ 
+ static char nvram_buf[NVRAM_SPACE];
+ static const u32 nvram_sizes[] = {0x8000, 0xF000, 0x10000};
++static int cfe_env;
++extern char *cfe_env_get(char *nv_buf, const char *name);
+ 
+ static u32 find_nvram_size(u32 end)
+ {
+@@ -46,6 +48,26 @@ static int nvram_find_and_copy(u32 base,
+ 	u32 *src, *dst;
+ 	u32 size;
+ 
++	cfe_env = 0;
++
++	/* XXX: hack for supporting the CFE environment stuff on WGT634U */
++	if (lim >= 8 * 1024 * 1024) {
++		src = (u32 *) KSEG1ADDR(base + 8 * 1024 * 1024 - 0x2000);
++		dst = (u32 *) nvram_buf;
++
++		if ((*src & 0xff00ff) == 0x000001) {
++			printk("early_nvram_init: WGT634U NVRAM found.\n");
++
++			for (i = 0; i < 0x1ff0; i++) {
++				if (*src == 0xFFFFFFFF)
++					break;
++				*dst++ = *src++;
++			}
++			cfe_env = 1;
++			return 0;
++		}
++	}
++
+ 	/* TODO: when nvram is on nand flash check for bad blocks first. */
+ 	off = FLASH_MIN;
+ 	while (off <= lim) {
+@@ -172,6 +194,13 @@ int bcm47xx_nvram_getenv(char *name, cha
+ 			return err;
+ 	}
+ 
++	if (cfe_env) {
++		value = cfe_env_get(nvram_buf, name);
++		if (!value)
++			return -ENOENT;
++		return snprintf(val, val_len, "%s", value);
++	}
++
+ 	/* Look for name=value and return value */
+ 	var = &nvram_buf[sizeof(struct nvram_header)];
+ 	end = nvram_buf + sizeof(nvram_buf) - 2;

target/linux/brcm47xx/patches-3.14/830-huawei_e970_support.patch

@@ -0,0 +1,101 @@
+--- a/arch/mips/bcm47xx/setup.c
++++ b/arch/mips/bcm47xx/setup.c
+@@ -36,6 +36,7 @@
+ #include <linux/ssb/ssb.h>
+ #include <linux/ssb/ssb_embedded.h>
+ #include <linux/bcma/bcma_soc.h>
++#include <linux/old_gpio_wdt.h>
+ #include <asm/bootinfo.h>
+ #include <asm/idle.h>
+ #include <asm/prom.h>
+@@ -266,6 +267,33 @@ static struct fixed_phy_status bcm47xx_f
+ 	.duplex	= DUPLEX_FULL,
+ };
+ 
++static struct gpio_wdt_platform_data gpio_wdt_data;
++
++static struct platform_device gpio_wdt_device = {
++	.name			= "gpio-wdt",
++	.id			= 0,
++	.dev			= {
++		.platform_data	= &gpio_wdt_data,
++	},
++};
++
++static int __init bcm47xx_register_gpio_watchdog(void)
++{
++	enum bcm47xx_board board = bcm47xx_board_get();
++
++	switch (board) {
++	case BCM47XX_BOARD_HUAWEI_E970:
++		pr_info("bcm47xx: detected Huawei E970 or similar, starting early gpio_wdt timer\n");
++		gpio_wdt_data.gpio = 7;
++		gpio_wdt_data.interval = HZ;
++		gpio_wdt_data.first_interval = HZ / 5;
++		return platform_device_register(&gpio_wdt_device);
++	default:
++		/* Nothing to do */
++		return 0;
++	}
++}
++
+ static int __init bcm47xx_register_bus_complete(void)
+ {
+ 	switch (bcm47xx_bus_type) {
+@@ -285,6 +313,7 @@ static int __init bcm47xx_register_bus_c
+ 	bcm47xx_workarounds();
+ 
+ 	fixed_phy_add(PHY_POLL, 0, &bcm47xx_fixed_phy_status);
++	bcm47xx_register_gpio_watchdog();
+ 	return 0;
+ }
+ device_initcall(bcm47xx_register_bus_complete);
+--- a/arch/mips/configs/bcm47xx_defconfig
++++ b/arch/mips/configs/bcm47xx_defconfig
+@@ -67,6 +67,7 @@ CONFIG_HW_RANDOM=y
+ CONFIG_GPIO_SYSFS=y
+ CONFIG_WATCHDOG=y
+ CONFIG_BCM47XX_WDT=y
++CONFIG_GPIO_WDT=y
+ CONFIG_SSB_DEBUG=y
+ CONFIG_SSB_DRIVER_GIGE=y
+ CONFIG_BCMA_DRIVER_GMAC_CMN=y
+--- a/drivers/ssb/embedded.c
++++ b/drivers/ssb/embedded.c
+@@ -34,11 +34,36 @@ int ssb_watchdog_timer_set(struct ssb_bu
+ }
+ EXPORT_SYMBOL(ssb_watchdog_timer_set);
+ 
++#ifdef CONFIG_BCM47XX
++#include <bcm47xx_board.h>
++
++static bool ssb_watchdog_supported(void)
++{
++	enum bcm47xx_board board = bcm47xx_board_get();
++
++	/* The Huawei E970 has a hardware watchdog using a GPIO */
++	switch (board) {
++	case BCM47XX_BOARD_HUAWEI_E970:
++		return false;
++	default:
++		return true;
++	}
++}
++#else
++static bool ssb_watchdog_supported(void)
++{
++	return true;
++}
++#endif
++
+ int ssb_watchdog_register(struct ssb_bus *bus)
+ {
+ 	struct bcm47xx_wdt wdt = {};
+ 	struct platform_device *pdev;
+ 
++	if (!ssb_watchdog_supported())
++		return 0;
++
+ 	if (ssb_chipco_available(&bus->chipco)) {
+ 		wdt.driver_data = &bus->chipco;
+ 		wdt.timer_set = ssb_chipco_watchdog_timer_set_wdt;

target/linux/brcm47xx/patches-3.14/920-cache-wround.patch

@@ -0,0 +1,138 @@
+--- a/arch/mips/include/asm/r4kcache.h
++++ b/arch/mips/include/asm/r4kcache.h
+@@ -21,10 +21,28 @@
+ #ifdef CONFIG_BCM47XX
+ #include <asm/paccess.h>
+ #include <linux/ssb/ssb.h>
+-#define BCM4710_DUMMY_RREG() ((void) *((u8 *) KSEG1ADDR(SSB_ENUM_BASE)))
++#define BCM4710_DUMMY_RREG() bcm4710_dummy_rreg()
++
++static inline unsigned long bcm4710_dummy_rreg(void)
++{
++      return *(volatile unsigned long *)(KSEG1ADDR(SSB_ENUM_BASE));
++}
++
++#define BCM4710_FILL_TLB(addr) bcm4710_fill_tlb((void *)(addr))
++
++static inline unsigned long bcm4710_fill_tlb(void *addr)
++{
++      return *(unsigned long *)addr;
++}
++
++#define BCM4710_PROTECTED_FILL_TLB(addr) bcm4710_protected_fill_tlb((void *)(addr))
++
++static inline void bcm4710_protected_fill_tlb(void *addr)
++{
++      unsigned long x;
++      get_dbe(x, (unsigned long *)addr);;
++}
+ 
+-#define BCM4710_FILL_TLB(addr) (*(volatile unsigned long *)(addr))
+-#define BCM4710_PROTECTED_FILL_TLB(addr) ({ unsigned long x; get_dbe(x, (volatile unsigned long *)(addr)); })
+ #else
+ #define BCM4710_DUMMY_RREG()
+ 
+--- a/arch/mips/mm/tlbex.c
++++ b/arch/mips/mm/tlbex.c
+@@ -935,6 +935,9 @@ build_get_pgde32(u32 **p, unsigned int t
+ 		uasm_i_srl(p, ptr, ptr, SMP_CPUID_PTRSHIFT);
+ 		uasm_i_addu(p, ptr, tmp, ptr);
+ #else
++#ifdef CONFIG_BCM47XX
++		uasm_i_nop(p);
++#endif
+ 		UASM_i_LA_mostly(p, ptr, pgdc);
+ #endif
+ 		uasm_i_mfc0(p, tmp, C0_BADVADDR); /* get faulting address */
+@@ -1277,12 +1280,12 @@ static void build_r4000_tlb_refill_handl
+ 			/* No need for uasm_i_nop */
+ 		}
+ 
+-#ifdef CONFIG_BCM47XX
+-		uasm_i_nop(&p);
+-#endif
+ #ifdef CONFIG_64BIT
+ 		build_get_pmde64(&p, &l, &r, K0, K1); /* get pmd in K1 */
+ #else
++# ifdef CONFIG_BCM47XX
++		uasm_i_nop(&p);
++# endif
+ 		build_get_pgde32(&p, K0, K1); /* get pgd in K1 */
+ #endif
+ 
+@@ -1294,6 +1297,9 @@ static void build_r4000_tlb_refill_handl
+ 		build_update_entries(&p, K0, K1);
+ 		build_tlb_write_entry(&p, &l, &r, tlb_random);
+ 		uasm_l_leave(&l, p);
++#ifdef CONFIG_BCM47XX
++		uasm_i_nop(&p);
++#endif
+ 		uasm_i_eret(&p); /* return from trap */
+ 	}
+ #ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+@@ -1838,12 +1844,12 @@ build_r4000_tlbchange_handler_head(u32 *
+ {
+ 	struct work_registers wr = build_get_work_registers(p);
+ 
+-#ifdef CONFIG_BCM47XX
+-	uasm_i_nop(p);
+-#endif
+ #ifdef CONFIG_64BIT
+ 	build_get_pmde64(p, l, r, wr.r1, wr.r2); /* get pmd in ptr */
+ #else
++# ifdef CONFIG_BCM47XX
++	uasm_i_nop(p);
++# endif
+ 	build_get_pgde32(p, wr.r1, wr.r2); /* get pgd in ptr */
+ #endif
+ 
+@@ -1882,6 +1888,9 @@ build_r4000_tlbchange_handler_tail(u32 *
+ 	build_tlb_write_entry(p, l, r, tlb_indexed);
+ 	uasm_l_leave(l, *p);
+ 	build_restore_work_registers(p);
++#ifdef CONFIG_BCM47XX
++	uasm_i_nop(p);
++#endif
+ 	uasm_i_eret(p); /* return from trap */
+ 
+ #ifdef CONFIG_64BIT
+--- a/arch/mips/kernel/genex.S
++++ b/arch/mips/kernel/genex.S
+@@ -21,6 +21,19 @@
+ #include <asm/war.h>
+ #include <asm/thread_info.h>
+ 
++#ifdef CONFIG_BCM47XX
++# ifdef eret
++#  undef eret
++# endif
++# define eret 					\
++	.set push;				\
++	.set noreorder;				\
++	 nop; 					\
++	 nop;					\
++	 eret;					\
++	.set pop;
++#endif
++
+ #ifdef CONFIG_MIPS_MT_SMTC
+ #define PANIC_PIC(msg)					\
+ 		.set	push;				\
+@@ -48,7 +61,6 @@ NESTED(except_vec3_generic, 0, sp)
+ 	.set	noat
+ #ifdef CONFIG_BCM47XX
+ 	nop
+-	nop
+ #endif
+ #if R5432_CP0_INTERRUPT_WAR
+ 	mfc0	k0, CP0_INDEX
+@@ -73,6 +85,9 @@ NESTED(except_vec3_r4000, 0, sp)
+ 	.set	push
+ 	.set	mips3
+ 	.set	noat
++#ifdef CONFIG_BCM47XX
++	nop
++#endif
+ 	mfc0	k1, CP0_CAUSE
+ 	li	k0, 31<<2
+ 	andi	k1, k1, 0x7c

target/linux/brcm47xx/patches-3.14/940-bcm47xx-yenta.patch

@@ -0,0 +1,46 @@
+--- a/drivers/pcmcia/yenta_socket.c
++++ b/drivers/pcmcia/yenta_socket.c
+@@ -920,6 +920,8 @@ static unsigned int yenta_probe_irq(stru
+ 	 * Probe for usable interrupts using the force
+ 	 * register to generate bogus card status events.
+ 	 */
++#ifndef CONFIG_BCM47XX
++	/* WRT54G3G does not like this */
+ 	cb_writel(socket, CB_SOCKET_EVENT, -1);
+ 	cb_writel(socket, CB_SOCKET_MASK, CB_CSTSMASK);
+ 	reg = exca_readb(socket, I365_CSCINT);
+@@ -935,6 +937,7 @@ static unsigned int yenta_probe_irq(stru
+ 	}
+ 	cb_writel(socket, CB_SOCKET_MASK, 0);
+ 	exca_writeb(socket, I365_CSCINT, reg);
++#endif
+ 
+ 	mask = probe_irq_mask(val) & 0xffff;
+ 
+@@ -1019,6 +1022,10 @@ static void yenta_get_socket_capabilitie
+ 	else
+ 		socket->socket.irq_mask = 0;
+ 
++	/* irq mask probing is broken for the WRT54G3G */
++	if (socket->socket.irq_mask == 0)
++		socket->socket.irq_mask = 0x6f8;
++
+ 	dev_printk(KERN_INFO, &socket->dev->dev,
+ 		   "ISA IRQ mask 0x%04x, PCI irq %d\n",
+ 		   socket->socket.irq_mask, socket->cb_irq);
+@@ -1257,6 +1264,15 @@ static int yenta_probe(struct pci_dev *d
+ 	dev_printk(KERN_INFO, &dev->dev,
+ 		   "Socket status: %08x\n", cb_readl(socket, CB_SOCKET_STATE));
+ 
++	/* Generate an interrupt on card insert/remove */
++	config_writew(socket, CB_SOCKET_MASK, CB_CSTSMASK | CB_CDMASK);
++
++	/* Set up Multifunction Routing Status Register */
++	config_writew(socket, 0x8C, 0x1000 /* MFUNC3 to GPIO3 */ | 0x2 /* MFUNC0 to INTA */);
++
++	/* Switch interrupts to parallelized */
++	config_writeb(socket, 0x92, 0x64);
++
+ 	yenta_fixup_parent_bridge(dev->subordinate);
+ 
+ 	/* Register it with the pcmcia layer.. */

target/linux/brcm47xx/patches-3.14/976-ssb_increase_pci_delay.patch

@@ -0,0 +1,11 @@
+--- a/drivers/ssb/driver_pcicore.c
++++ b/drivers/ssb/driver_pcicore.c
+@@ -375,7 +375,7 @@ static void ssb_pcicore_init_hostmode(st
+ 	set_io_port_base(ssb_pcicore_controller.io_map_base);
+ 	/* Give some time to the PCI controller to configure itself with the new
+ 	 * values. Not waiting at this point causes crashes of the machine. */
+-	mdelay(10);
++	mdelay(300);
+ 	register_pci_controller(&ssb_pcicore_controller);
+ }
+ 

target/linux/brcm47xx/patches-3.14/980-wnr834b_no_cardbus_invariant.patch

@@ -0,0 +1,13 @@
+--- a/arch/mips/bcm47xx/setup.c
++++ b/arch/mips/bcm47xx/setup.c
+@@ -127,6 +127,10 @@ static int bcm47xx_get_invariants(struct
+ 	if (bcm47xx_nvram_getenv("cardbus", buf, sizeof(buf)) >= 0)
+ 		iv->has_cardbus_slot = !!simple_strtoul(buf, NULL, 10);
+ 
++	/* Do not indicate cardbus for Netgear WNR834B V1 and V2 */
++	if (iv->boardinfo.type == 0x0472 && iv->has_cardbus_slot)
++		iv->has_cardbus_slot = 0;
++
+ 	return 0;
+ }
+ 

target/linux/brcm47xx/patches-3.14/999-wl_exports.patch

@@ -0,0 +1,22 @@
+--- a/arch/mips/bcm47xx/nvram.c
++++ b/arch/mips/bcm47xx/nvram.c
+@@ -20,7 +20,8 @@
+ #include <bcm47xx_nvram.h>
+ #include <asm/mach-bcm47xx/bcm47xx.h>
+ 
+-static char nvram_buf[NVRAM_SPACE];
++char nvram_buf[NVRAM_SPACE];
++EXPORT_SYMBOL(nvram_buf);
+ static const u32 nvram_sizes[] = {0x8000, 0xF000, 0x10000};
+ static int cfe_env;
+ extern char *cfe_env_get(char *nv_buf, const char *name);
+--- a/arch/mips/mm/cache.c
++++ b/arch/mips/mm/cache.c
+@@ -58,6 +58,7 @@ void (*_dma_cache_wback)(unsigned long s
+ void (*_dma_cache_inv)(unsigned long start, unsigned long size);
+ 
+ EXPORT_SYMBOL(_dma_cache_wback_inv);
++EXPORT_SYMBOL(_dma_cache_inv);
+ 
+ #endif /* CONFIG_DMA_NONCOHERENT */
+