ath79: add support for TP-Link CPE510 v1

TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with
two Ethernet ports based on Atheros AR9334

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 2T2R 5 GHz
 - 13 dBi built-in antenna
 - Power, LAN0, LAN1 green LEDs
 - 4x green RSSI LEDs

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Based on the work of Paul Wassi <[email protected]>

Signed-off-by: Adrian Schmutzler <[email protected]>

target/linux/ath79/base-files/etc/board.d/01_leds

@@ -158,7 +158,8 @@ tplink,archer-d50-v1)
 	ucidef_set_led_switch "wan_data" "WAN Data" "tp-link:white:internet" "switch0" "0x02" "" "tx rx"
 	ucidef_set_led_switch "wan_link" "WAN Link" "tp-link:white:wan" "switch0" "0x02" "" "link"
 	;;
-tplink,cpe210-v1)
+tplink,cpe210-v1|\
+tplink,cpe510-v1)
 	ucidef_set_led_netdev "lan0" "LAN0" "tp-link:green:lan0" "eth1"
 	ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
 	ucidef_set_rssimon "wlan0" "200000" "1"

target/linux/ath79/base-files/etc/board.d/02_network

@@ -103,6 +103,7 @@ ath79_setup_interfaces()
 	comfast,cf-e110n-v2|\
 	comfast,cf-e120a-v3|\
 	tplink,cpe210-v1|\
+	tplink,cpe510-v1|\
 	ubnt,nanostation-m|\
 	ubnt,routerstation)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"

target/linux/ath79/base-files/etc/board.d/03_gpio_switches

@@ -42,7 +42,8 @@ tplink,archer-c25-v1)
 	ucidef_add_gpio_switch "led_control" "LED control" "21" "0"
 	ucidef_add_gpio_switch "led_reset" "LED reset" "19" "1"
 	;;
-tplink,cpe210-v1)
+tplink,cpe210-v1|\
+tplink,cpe510-v1)
 	ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "20"
 	;;
 ubnt,nanostation-ac)

target/linux/ath79/dts/ar9344_tplink_cpe510-v1.dts

@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar9344_tplink_cpexxx-v1.dtsi"
+
+/ {
+	compatible = "tplink,cpe510-v1", "qca,ar9344";
+	model = "TP-Link CPE510 v1";
+};

target/linux/ath79/image/generic-tp-link.mk

@@ -195,6 +195,18 @@ define Device/tplink_cpe210-v3
 endef
 TARGET_DEVICES += tplink_cpe210-v3
 
+define Device/tplink_cpe510-v1
+  $(Device/tplink-loader-okli)
+  ATH_SOC := ar9344
+  IMAGE_SIZE := 7680k
+  DEVICE_MODEL := CPE510
+  DEVICE_VARIANT := v1
+  DEVICE_PACKAGES := rssileds
+  TPLINK_BOARD_ID := CPE510
+  SUPPORTED_DEVICES += cpe510
+endef
+TARGET_DEVICES += tplink_cpe510-v1
+
 define Device/tplink_cpe510-v2
   $(Device/tplink-loader-okli)
   ATH_SOC := ar9344