layerscape: add Traverse LS1043-S support

The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.

Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.

This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.

Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.

Signed-off-by: Mathew McBride <[email protected]>

target/linux/layerscape/base-files/etc/board.d/01_led

@@ -0,0 +1,25 @@
+#!/bin/sh
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+traverse,ls1043v)
+	ucidef_set_led_netdev "wan" "WAN LED" "ls1043v:yellow:wan" "eth4"
+	;;
+traverse,ls1043s)
+	ucidef_set_led_netdev "wan" "WAN LED" "ls1043s:yellow:wan" "eth4"
+	ucidef_set_led_netdev "xgact" "10G Activity" "ls1043s:yellow:10gact" "eth6"
+	ucidef_set_led_netdev "xglink" "10G Link" "ls1043s:green:10glink" "eth6"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/layerscape/base-files/etc/board.d/02_network

@@ -0,0 +1,21 @@
+#!/bin/sh
+
+. /lib/functions/system.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+	traverse,ls1043v)
+		ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
+		ucidef_set_interface_wan "eth4"
+		;;
+	traverse,ls1043s)
+		ucidef_set_interface_lan "eth0 eth1 eth2 eth3 eth6"
+		ucidef_set_interface_wan "eth4"
+		;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/layerscape/base-files/etc/board.d/03_gpio_switches

@@ -0,0 +1,28 @@
+#!/bin/sh
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+traverse,ls1043v)
+	ucidef_add_gpio_switch "lte_reset" "LTE Reset" "377"
+	ucidef_add_gpio_switch "lte_disable" "LTE Airplane mode" "378"
+	;;
+traverse,ls1043s)
+	ucidef_add_gpio_switch "tensfp_txdisable" "SFP+ TX Disable" "378"
+	ucidef_add_gpio_switch "gigsfp_txdisable" "SFP TX Disable" "381"
+	ucidef_add_gpio_switch "lte_reset" "LTE Reset" "502"
+	ucidef_add_gpio_switch "lte_disable" "LTE Airplane Mode" "394"
+	ucidef_add_gpio_switch "lte_power" "LTE Power" "395"
+	;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/layerscape/base-files/lib/preinit/05_layerscape_reorder_eth

@@ -0,0 +1,28 @@
+#!/bin/sh
+
+reorder_layerscape_interfaces() {
+	if [ ! -f /tmp/sysinfo/board_name ]; then
+		echo "No board name found, not doing reorder_layerscape_interfaces"
+		return 0
+	fi
+
+	board=$(cat /tmp/sysinfo/board_name)
+	case "$board" in
+	"traverse,ls1043v" | \
+	"traverse,ls1043s")
+
+		# Reorder ethernet interfaces to match the physical order
+		ip link set eth2 name fm1-mac3
+		ip link set eth4 name eth2
+		ip link set eth3 name fm1-mac4
+		ip link set eth5 name eth3
+		ip link set fm1-mac3 name eth4
+		ip link set fm1-mac4 name eth5
+		;;
+	default)
+		echo "Unknown board $board"
+		;;
+	esac
+}
+
+boot_hook_add preinit_main reorder_layerscape_interfaces

target/linux/layerscape/base-files/lib/upgrade/platform.sh

@@ -0,0 +1,94 @@
+#!/bin/sh
+#
+# Copyright 2015-2018 Traverse Technologies
+#
+platform_do_upgrade_traverse_nandubi() {
+	bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}')
+	newbootsys=2
+	if [ "$bootsys" -eq "2" ]; then
+		newbootsys=1
+	fi
+	mkdir -p /tmp/image
+	cd /tmp/image
+	get_image "$1" > image.tar
+	ls -la image.tar
+	files=$(tar -tf image.tar)
+	echo "Files in image:"
+	echo $files
+	for f in $files
+	do
+		part_name=$(echo $f | awk -F '/' '{{print $2}}')
+		if [ -z "$part_name" ] || [ "$part_name" = "CONTROL" ]; then
+			continue
+		fi
+
+		[ "$part_name" = "root" ] && part_name="rootfs"
+
+		volume=$part_name
+		if [ "$part_name" = "kernel" ] || [ "$part_name" = "rootfs" ]; then
+			volume="${part_name}${newbootsys}"
+		fi
+		volume_id=$(ubinfo -d 0 --name $volume | awk '/Volume ID/ {print $3}')
+		file_size=$(tar -tvf image.tar $f | awk '{{print $3}}')
+		echo "$f size $file_size"
+		tar -xOf image.tar $f | ubiupdatevol -s $file_size /dev/ubi0_$volume_id -
+		
+		echo "$volume upgraded"
+	done
+	fw_setenv bootsys $newbootsys
+	echo "Upgrade complete"
+}
+platform_copy_config() {
+	bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}')
+	rootvol=rootfs$bootsys
+	volume_id=$(ubinfo -d 0 --name $rootvol | awk '/Volume ID/ {print $3}')
+	mkdir -p /mnt/oldsys
+	mount -t ubifs -o rw,noatime /dev/ubi0_$volume_id /mnt/oldsys
+	cp -af "$CONF_TAR" /mnt/oldsys
+	umount /mnt/oldsys
+}
+platform_check_image() {
+	local board=$(board_name)
+
+	case "$board" in
+	traverse,ls1043v | \
+	traverse,ls1043s | \
+	traverse,five64)
+		local tar_file="$1"
+		local kernel_length=$( (tar xf $tar_file sysupgrade-traverse-five64/kernel -O | wc -c) 2> /dev/null)
+		local rootfs_length=$( (tar xf $tar_file sysupgrade-traverse-five64/root -O | wc -c) 2> /dev/null)
+		[ "$kernel_length" -eq 0 -o "$rootfs_length" -eq 0 ] && {
+			echo "The upgrade image is corrupt."
+			return 1
+		}
+		return 0
+		;;
+	*)
+		echo "Sysupgrade is not currently supported on $board"
+		;;
+	esac
+
+	return 1
+}
+platform_do_upgrade() {
+	local board=$(board_name)
+
+	case "$board" in
+	traverse,ls1043v | \
+	traverse,ls1043s | \
+	traverse,five64)
+		platform_do_upgrade_traverse_nandubi "$ARGV"
+		;;
+	*)
+		echo "Sysupgrade is not currently supported on $board"
+		;;
+	esac
+}
+platform_pre_upgrade() {
+	# Force the creation of fw_printenv.lock
+	mkdir -p /var/lock
+	touch /var/lock/fw_printenv.lock
+	
+	export RAMFS_COPY_BIN="/usr/sbin/fw_printenv /usr/sbin/fw_setenv /usr/sbin/ubinfo /bin/echo ${RAMFS_COPY_BIN}"
+	export RAMFS_COPY_DATA="/etc/fw_env.config /var/lock/fw_printenv.lock ${RAMFS_COPY_DATA}"
+}

target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts

@@ -0,0 +1,332 @@
+/*
+ * Device Tree Include file for Traverse LS1043S board.
+ *
+ * Copyright 2014-2015, Freescale Semiconductor
+ * Copyright 2017-2018, Traverse Technologies
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "fsl-ls1043a.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Traverse LS1043S";
+	compatible = "traverse,ls1043s";
+
+	aliases {
+		crypto = &crypto;
+		ethernet0 = &EMAC0;
+		ethernet1 = &EMAC1;
+		ethernet2 = &EMAC2;
+		ethernet3 = &EMAC3;
+		ethernet4 = &EMAC4;
+		ethernet5 = &EMAC5;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		gpio0 {
+			label = "ls1043s:green:user0";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+		};
+		gpio1 {
+			label = "ls1043s:green:user1";
+			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+		};
+		/* LED D17 */
+		gpio2 {
+			label = "ls1043s:green:wan";
+			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+		};
+		gpio3 {
+			label = "ls1043s:yellow:wan";
+			gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+		};
+		/* LED D18 */
+		gpio4 {
+			label = "ls1043s:green:mgmt";
+			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+		};
+		gpio5 {
+			label = "ls1043s:yellow:mgmt";
+			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+		};
+		/* LED D6 */
+		gpio6 {
+			label = "ls1043s:green:user2";
+			gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		/* SFP+ LEDs - these are for chassis
+		 * with lightpipes only
+		 */
+		teng_act {
+			label = "ls1043s:yellow:10gact";
+			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+		};
+
+		teng_link {
+			label = "ls1043s:green:10glink";
+			gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+	
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <1000>;
+		/* This button may not be loaded on all boards */
+		button@0 {
+			label = "Front button";
+			linux,code = <KEY_SETUP>;
+			gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		};
+		/* This is wired to header S3 */
+		button@1 {
+			label = "Rear button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&esdhc {
+	mmc-hs200-1_8v;
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
+};
+
+&i2c0 {
+	status = "okay";
+	rtc@6f {
+		compatible = "intersil,isl1208";
+		reg = <0x6f>;
+	};
+
+	sfp_pca9534: pca9534@24 {
+		compatible = "ti,tca9534", "nxp,pca9534";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x24>;
+		gpio-base = <100>;
+	};
+
+	controller@50 {
+		compatible = "traverse,controller";
+		reg = <0x50>;
+	};
+
+	ds125df111@18 {
+		compatible = "ti,ds125df111";
+		reg = <0x18>;
+	};
+
+	emc1704@4c {
+		compatible = "microchip,emc1704";
+		reg = <0x4c>;
+	};
+
+	pac1934@16 {
+		compatible = "microchip,pac1934";
+		reg = <0x16>;
+		/* Monitoring 3.3V, 5V, Vin/12V (voltage only), Vbat/RTC (voltage only) */
+		shunt-resistors = <4000 12000 0 0>;
+	};
+
+	pmic@8 {
+		compatible = "freescale,mc34vr500";
+		reg = <0x08>;
+	};
+};
+
+/* I2C Bus for SFP EEPROM and control
+ * These are multiplexed so
+ * they don't collide when loaded
+ */
+&i2c3 {
+	status = "okay";
+	i2c-switch@70 {
+		compatible = "nxp,pca9540";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		gigsfp_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		tensfp_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&ifc {
+	status = "okay";
+	#address-cells = <2>;
+	#size-cells = <1>;
+	/* Only NAND flash is used on this board */
+	ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>;
+
+	nand@1,0 {
+		compatible = "fsl,ifc-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x10000>;
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
+
+#include "fsl-ls1043-post.dtsi"
+
+&fman0 {
+	EMAC0: ethernet@e0000 {
+		phy-handle = <&qsgmii_phy1>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 01];
+	};
+
+	EMAC1: ethernet@e2000 {
+		phy-handle = <&qsgmii_phy2>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 02];
+	};
+
+	EMAC2: ethernet@e8000 {
+		phy-handle = <&qsgmii_phy3>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 03];
+	};
+
+	EMAC3: ethernet@ea000 {
+		phy-handle = <&qsgmii_phy4>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 04];
+	};
+
+	/* SFP via AR8031
+	 * We treat this as a fixed-link as the
+	 * AR8031 is hard-configured into
+	 * 1000BASE-X mode
+	 * Should MII control be desired, remove
+	 * fixed-link and add
+	 * phy-handle = <&rgmii_phy1>;
+	 */
+	EMAC4: ethernet@e4000 {
+		phy-connection-type = "rgmii";
+		local-mac-address = [0A 00 00 00 00 05];
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+
+	/* Connection to Expansion (M.2) slot
+	 * Future WAN (i.e xDSL) plugin
+	 */
+	EMAC5: ethernet@e6000 {
+		phy-connection-type = "rgmii-id";
+		local-mac-address = [00 00 00 00 00 06];
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+
+	/* 10G SFP+ interface
+	 * This can also run at 1.25 and 2.5G with
+	 * the appropriate SerDes protocol setting in RCW
+	 */
+	TENSFP: ethernet@f0000 {
+		status = "okay";
+		phy-connection-type = "xgmii";
+		fixed-link {
+			speed = <10000>;
+			full-duplex;
+		};
+	};
+
+	mdio@fc000 {
+		rgmii_phy1: ethernet-phy@2 {
+			reg = <0x2>;
+		};
+		qsgmii_phy1: ethernet-phy@4 {
+			reg = <0x4>;
+		};
+		qsgmii_phy2: ethernet-phy@5 {
+			reg = <0x5>;
+		};
+		qsgmii_phy3: ethernet-phy@6 {
+			reg = <0x6>;
+		};
+		qsgmii_phy4: ethernet-phy@7 {
+			reg = <0x7>;
+		};
+	};
+};
+
+/* No QUICC engine functions on this board -
+ * pins are used for other functions (GPIO, I2C etc.)
+ */
+&uqe {
+	status = "disabled";
+};
+
+/* LS1043S does not use the QorIQ AHCI
+ * controller.
+ */
+&sata {
+	status = "disabled";
+};

target/linux/layerscape/files/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts

@@ -0,0 +1,253 @@
+/*
+ * Device Tree Include file for Traverse LS1043V board.
+ *
+ * Copyright 2014-2015, Freescale Semiconductor
+ * Copyright 2017, Traverse Technologies
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "fsl-ls1043a.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Traverse LS1043V";
+	compatible = "traverse,ls1043v";
+
+	aliases {
+		crypto = &crypto;
+		ethernet0 = &EMAC0;
+		ethernet1 = &EMAC1;
+		ethernet2 = &EMAC2;
+		ethernet3 = &EMAC3;
+		ethernet4 = &EMAC4;
+		ethernet5 = &EMAC5;
+		pca9555 = &pca9555;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		gpio0 {
+			label = "ls1043v:green:user0";
+			gpios = <&pca9555 0 GPIO_ACTIVE_LOW>;
+		};
+		gpio1 {
+			label = "ls1043v:yellow:user0";
+			gpios = <&pca9555 1 GPIO_ACTIVE_LOW>;
+		};
+		gpio2 {
+			label = "ls1043v:green:user1";
+			gpios = <&pca9555 2 GPIO_ACTIVE_LOW>;
+		};
+		gpio3 {
+			label = "ls1043v:yellow:user1";
+			gpios = <&pca9555 3 GPIO_ACTIVE_LOW>;
+		};
+		gpio4 {
+			label = "ls1043v:green:user2";
+			gpios = <&pca9555 4 GPIO_ACTIVE_HIGH>;
+		};
+		gpio5 {
+			label = "ls1043v:yellow:wlan";
+			gpios = <&pca9555 5 GPIO_ACTIVE_HIGH>;
+		};
+		gpio6 {
+			label = "ls1043v:yellow:wan";
+			gpios = <&pca9555 6 GPIO_ACTIVE_HIGH>;
+		};
+	};
+	
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <1000>;
+		button@0 {
+			label = "Front button";
+			linux,code = <KEY_SETUP>;
+			gpios = <&pca9555 14 GPIO_ACTIVE_LOW>;
+		};
+		button@1 {
+			label = "Rear button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pca9555 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	rtc@6f {
+		compatible = "intersil,isl1208";
+		reg = <0x6f>;
+	};
+
+	pca9555: pca9555@20 {
+		compatible = "nxp,pca9555";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x20>;
+		gpio-base = <0>;
+	};
+
+	/* CPU core temp sensor and VDD (1.0V) sensor */
+	ltc2990@4c {
+		compatible = "lltc,ltc2990";
+		reg = <0x4C>;
+		lltc,meas-mode = <4 3>;
+	};
+
+	/* 3.3V and 5V monitor (may not be loaded on some SKUs) */
+	ltc2990@4f {
+		compatible = "lltc,ltc2990";
+		reg = <0x4F>;
+		lltc,meas-mode = <6 3>;
+	};
+};
+
+&ifc {
+	status = "okay";
+	#address-cells = <2>;
+	#size-cells = <1>;
+	/* Only NAND flash is used on this board */
+	ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>;
+
+	nand@1,0 {
+		compatible = "fsl,ifc-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x10000>;
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
+
+#include "fsl-ls1043-post.dtsi"
+
+&fman0 {
+	EMAC0: ethernet@e0000 {
+		phy-handle = <&qsgmii_phy1>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 01];
+	};
+
+	EMAC1: ethernet@e2000 {
+		phy-handle = <&qsgmii_phy2>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 02];
+	};
+
+	EMAC2: ethernet@e8000 {
+		phy-handle = <&qsgmii_phy3>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 03];
+	};
+
+	EMAC3: ethernet@ea000 {
+		phy-handle = <&qsgmii_phy4>;
+		phy-connection-type = "qsgmii";
+		local-mac-address = [0A 00 00 00 00 04];
+	};
+	EMAC4: ethernet@e4000 {
+		phy-handle = <&rgmii_phy1>;
+		phy-connection-type = "rgmii";
+		local-mac-address = [0A 00 00 00 00 05];
+	};
+
+	/* Connection to VDSL SoC */
+	EMAC5: ethernet@e6000 {
+		phy-connection-type = "rgmii-id";
+		local-mac-address = [00 00 00 00 00 06];
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+
+	/* 10G XFI interface - not in use on this platform */
+	TENSFP: ethernet@f0000 {
+		status = "disabled";
+
+		phy-connection-type = "sgmii";
+		fixed-link {
+			/* NB: speed = 1000 and sgmii allows forward compatibility
+			*  with both 1G and 10G, the same is not true
+			*  in the reverse.
+			*/
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+
+	mdio@fc000 {
+		rgmii_phy1: ethernet-phy@3 {
+			reg = <0x3>;
+		};
+		qsgmii_phy1: ethernet-phy@4 {
+			reg = <0x4>;
+		};
+		qsgmii_phy2: ethernet-phy@5 {
+			reg = <0x5>;
+		};
+		qsgmii_phy3: ethernet-phy@6 {
+			reg = <0x6>;
+		};
+		qsgmii_phy4: ethernet-phy@7 {
+			reg = <0x7>;
+		};
+	};
+};
+
+/* No QUICC engine functions on this board */
+&uqe {
+	status = "disabled";
+};
+
+/* No SATA/AHCI on this board */
+&sata {
+       status = "disabled";
+};

target/linux/layerscape/image/Makefile

@@ -7,6 +7,8 @@
 include $(TOPDIR)/rules.mk
 include $(INCLUDE_DIR)/image.mk
 
+ITB_BOARDS = traverse-five64
+
 define Build/append-ls-rcw
 	rm -f $@
 	dd if=$(STAGING_DIR_IMAGE)/$(1)-rcw.bin >> $@
@@ -45,6 +47,16 @@ define Build/append-ls-dtb
 	dd if=$(DTS_DIR)/$(1).dtb >> $@
 endef
 
+define Build/traverse-fit
+	./mkits-multiple-config.sh -o [email protected] -A $(LINUX_KARCH) -v $(LINUX_VERSION) \
+		-k $@ -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
+		-C gzip -c 1 -c 2 \
+		-d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043s.dtb -D "Traverse_LS1043S" -n "ls1043s" -a $(FDT_LOADADDR) -c 1 \
+		-d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043v.dtb -D "Traverse_LS1043V" -n "ls1043v" -a $(FDT_LOADADDR) -c 2
+	PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f [email protected] [email protected]
+	@mv -f [email protected] $@
+endef
+
 define Device/Default
   PROFILES = Default
   FILESYSTEMS := squashfs
@@ -62,6 +74,7 @@ ifeq ($(SUBTARGET),armv8_32b)
   KERNEL_LOADADDR = 0x80008000
   KERNEL_ENTRY_POINT = 0x80008000
 endif
+  FDT_LOADADDR = 0x90000000
 endef
 
 define Device/ls1043ardb
@@ -182,4 +195,28 @@ endef
 TARGET_DEVICES += ls2088ardb
 endif
 
+define Device/traverse-five64
+  KERNEL_NAME := Image
+  KERNEL_SUFFIX := -kernel.itb
+  KERNEL_INSTALL := 1
+  FILESYSTEMS := ubifs
+  DEVICE_TITLE := Traverse LS1043 Boards (Five64, LS1043S)
+  DEVICE_PACKAGES += fman-layerscape-ls1043ardb kmod-i2c-core kmod-rtc-isl1208 uboot-envtools \
+	uboot-traverse-ls1043v uboot-traverse-ls1043v-sdcard \
+	kmod-hwmon-core kmod-hwmon-ltc2990 kmod-gpio-pca953x kmod-input-gpio-keys-polled \
+	kmod-i2c-mux-pca954x kmod-hwmon-pac1934 kmod-hwmon-emc17xx
+  DEVICE_DESCRIPTION = Build images for Traverse LS1043 boards. This generates a single image \
+  	capable of booting on any of the boards in this family.
+  DEVICE_DTS = freescale/traverse-ls1043s
+  DEVICE_DTS_DIR = $(LINUX_DIR)/arch/arm64/boot/dts
+  DEVICE_DTS_CONFIG = ls1043s
+  KERNEL := kernel-bin | gzip | traverse-fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FDT_LOADADDR)
+  KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FDT_LOADADDR)
+  IMAGES = root sysupgrade.tar
+  IMAGE/root = append-rootfs
+  IMAGE/sysupgrade.tar = sysupgrade-tar
+  UBIFS_OPTS := -m 2048 -e 124KiB -c 4096
+endef
+TARGET_DEVICES += traverse-five64
+
 $(eval $(call BuildImage))

target/linux/layerscape/patches-4.9/304-dts-layerscape-add-traverse-ls1043.patch

@@ -0,0 +1,89 @@
+From c0612164b379ebc8964da6bc6f6ced9736dce488 Mon Sep 17 00:00:00 2001
+From: Mathew McBride <[email protected]>
+Date: Tue, 17 Apr 2018 10:01:03 +1000
+Subject: [PATCH] add DTS for Traverse LS1043 Boards
+
+Signed-off-by: Mathew McBride <[email protected]>
+---
+ arch/arm64/boot/dts/freescale/Makefile |    5 ++++-
+ 1 file changed, 4 insertions(+), 1 deletion(-)
+ create mode 100644 arch/arm64/boot/dts/freescale/traverse-ls1043v.dts
+
+--- a/arch/arm64/boot/dts/freescale/Makefile
++++ b/arch/arm64/boot/dts/freescale/Makefile
+@@ -20,7 +20,10 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2
+ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
+ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
+ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+- 
++
++dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043v.dtb
++dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043s.dtb
++
+ always		:= $(dtb-y)
+ subdir-y	:= $(dts-dirs)
+ clean-files	:= *.dtb
+--- a/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts
++++ b/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts
+@@ -337,3 +337,29 @@
+ &sata {
+ 	status = "disabled";
+ };
++
++/* Additions for Layerscape SDK (4.4/4.9) Kernel only
++ * These kernels need additional setup for FMan/QMan DMA shared memory
++ */
++
++&bman_fbpr {
++	compatible = "fsl,bman-fbpr";
++	alloc-ranges = <0 0 0x10000 0>;
++};
++&qman_fqd {
++	compatible = "fsl,qman-fqd";
++	alloc-ranges = <0 0 0x10000 0>;
++};
++&qman_pfdr {
++	compatible = "fsl,qman-pfdr";
++	alloc-ranges = <0 0 0x10000 0>;
++};
++
++&soc {
++#include "qoriq-dpaa-eth.dtsi"
++#include "qoriq-fman3-0-6oh.dtsi"
++};
++
++&fman0 {
++	compatible = "fsl,fman", "simple-bus";
++};
+--- a/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts
++++ b/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts
+@@ -313,3 +313,29 @@
+ &sata {
+        status = "disabled";
+ };
++
++/* Additions for Layerscape SDK (4.4/4.9) Kernel only
++ * These kernels need additional setup for FMan/QMan DMA shared memory
++ */
++
++&bman_fbpr {
++	compatible = "fsl,bman-fbpr";
++	alloc-ranges = <0 0 0x10000 0>;
++};
++&qman_fqd {
++	compatible = "fsl,qman-fqd";
++	alloc-ranges = <0 0 0x10000 0>;
++};
++&qman_pfdr {
++	compatible = "fsl,qman-pfdr";
++	alloc-ranges = <0 0 0x10000 0>;
++};
++
++&soc {
++#include "qoriq-dpaa-eth.dtsi"
++#include "qoriq-fman3-0-6oh.dtsi"
++};
++
++&fman0 {
++	compatible = "fsl,fman", "simple-bus";
++};

target/linux/layerscape/patches-4.9/820-rgmii-fixed-link.patch

@@ -5,8 +5,8 @@ Subject: [PATCH] Recognize when an RGMII Link is set as fixed (in the device
  tree) and set up the MAC accordingly
 
 ---
- drivers/net/ethernet/freescale/sdk_dpaa/mac.c               |  1 +
- .../ethernet/freescale/sdk_fman/Peripherals/FM/MAC/memac.c  | 13 +++++++++++++
+ drivers/net/ethernet/freescale/sdk_dpaa/mac.c                      |    1 
+ drivers/net/ethernet/freescale/sdk_fman/Peripherals/FM/MAC/memac.c |   13 ++++++++++
  2 files changed, 14 insertions(+)
 
 --- a/drivers/net/ethernet/freescale/sdk_dpaa/mac.c
@@ -43,19 +43,19 @@ Subject: [PATCH] Recognize when an RGMII Link is set as fixed (in the device
  {
      t_Memac     *p_Memac = (t_Memac *)h_Memac;
  
-+	struct mac_device *mac_dev = (struct mac_device *)p_Memac->h_App;
++    struct mac_device *mac_dev = (struct mac_device *)p_Memac->h_App;
 +
      SANITY_CHECK_RETURN_ERROR(p_Memac, E_INVALID_HANDLE);
      SANITY_CHECK_RETURN_ERROR(!p_Memac->p_MemacDriverParam, E_INVALID_STATE);
  
      fman_memac_enable(p_Memac->p_MemMap, (mode & e_COMM_MODE_RX), (mode & e_COMM_MODE_TX));
  
-+	if (ENET_INTERFACE_FROM_MODE(p_Memac->enetMode) == e_ENET_IF_RGMII) {
-+		if (mac_dev->fixed_link) {
-+			printk("This is a fixed-link, forcing speed %d duplex %d\n",mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
-+			MemacAdjustLink(h_Memac,mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
-+		}
++    if (ENET_INTERFACE_FROM_MODE(p_Memac->enetMode) == e_ENET_IF_RGMII) {
++	if (mac_dev->fixed_link) {
++		printk(KERN_INFO "This is a fixed-link, forcing speed %d duplex %d\n",mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
++		MemacAdjustLink(h_Memac,mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
 +	}
++    }
 +
      return E_OK;
  }

target/linux/layerscape/patches-4.9/821-add-esdhc-vsel-to-ls1043.patch

@@ -0,0 +1,10 @@
+--- a/drivers/mmc/host/sdhci-of-esdhc.c
++++ b/drivers/mmc/host/sdhci-of-esdhc.c
+@@ -619,6 +619,7 @@ static void esdhc_reset(struct sdhci_hos
+ static const struct of_device_id scfg_device_ids[] = {
+ 	{ .compatible = "fsl,t1040-scfg", },
+ 	{ .compatible = "fsl,ls1012a-scfg", },
++	{ .compatible = "fsl,ls1043a-scfg", },
+ 	{ .compatible = "fsl,ls1046a-scfg", },
+ 	{}
+ };