ipq40xx: Use SoC DTSI for Teltonika RUTX

Teltonika RUTX currently is the only device pulling in DK01 DTSI and thus
preventing removal of DK01 and DK04 support.

So, lets add the missing nodes from DK01 DTSI and use the SoC DTSI instead.

Signed-off-by: Robert Marko <[email protected]>

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-rutx.dtsi

@@ -1,9 +1,10 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
-#include "qcom-ipq4019-ap.dk01.1.dtsi"
+#include "qcom-ipq4019.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
 
 / {
 	memory {
@@ -11,28 +12,39 @@
 		reg = <0x80000000 0x10000000>;
 	};
 
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	soc {
-		pinctrl@1000000 {
-			mdio_pins: mdio_pinmux {
-				mux_1 {
-					pins = "gpio53";
-					function = "mdio";
-					bias-pull-up;
-				};
-				mux_2 {
-					pins = "gpio52";
-					function = "mdc";
-					bias-pull-up;
-				};
-			};
-
-			i2c_0_pins: i2c_0_pinmux {
-				mux {
-					pins = "gpio58", "gpio59";
-					function = "blsp_i2c0";
-					bias-disable;
-				};
-			};
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			status = "okay";
+
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
 		};
 
 		keys {
@@ -47,9 +59,91 @@
 	};
 };
 
+&prng {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+		};
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio54";
+		};
+		pinconf {
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		pinconf_cs {
+			pins = "gpio54";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio53";
+			function = "mdio";
+			bias-pull-up;
+		};
+		mux_2 {
+			pins = "gpio52";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	i2c_0_pins: i2c_0_pinmux {
+		mux {
+			pins = "gpio58", "gpio59";
+			function = "blsp_i2c0";
+			bias-disable;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
 &blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
 	cs-gpios = <&tlmm 54 0>, <&tlmm 63 0>;
 	num-cs = <2>;
+	status = "okay";
 
 	xt25f128b@0 {
 		/*
@@ -208,3 +302,23 @@
 	pinctrl-names = "default";
 	phy-reset-gpio = <&tlmm 62 0>;
 };
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};