ipq40xx: add Edgecore OAP-100 support

flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
  - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
  - ubiattach -p /dev/mtd0
  - ubirmvol /dev/ubi0 -n0
  - ubirmvol /dev/ubi0 -n1
  - ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
  - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin

Signed-off-by: John Crispin <[email protected]>

package/firmware/ipq-wifi/Makefile

@@ -33,6 +33,7 @@ ALLWIFIBOARDS:= \
 	dlink_dap2610 \
 	edgecore_ecw5211 \
 	edgecore_ecw5410 \
+	edgecore_oap100 \
 	engenius_eap2200 \
 	engenius_emd1 \
 	engenius_emr3500 \
@@ -109,6 +110,7 @@ $(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
 $(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
 $(eval $(call generate-ipq-wifi-package,edgecore_ecw5211,Edgecore ECW5211))
 $(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
+$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
 $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
 $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
 $(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))

target/linux/ipq40xx/base-files/etc/board.d/01_leds

@@ -27,6 +27,10 @@ avm,fritzbox-7530 |\
 glinet,gl-b1300)
 	ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
 	;;
+edgecore,oap100)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:blue:wlan5g" "phy1tpt"
+	;;
 engenius,eap1300)
 	ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -39,6 +39,7 @@ ipq40xx_setup_interfaces()
 	asus,map-ac2200|\
 	cilab,meshpoint-one|\
 	edgecore,ecw5211|\
+	edgecore,oap100|\
 	openmesh,a42|\
 	openmesh,a62)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"

target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -94,6 +94,7 @@ case "$FIRMWARE" in
 	compex,wpj419 |\
 	compex,wpj428 |\
 	edgecore,ecw5211 |\
+	edgecore,oap100 |\
 	engenius,eap1300 |\
 	engenius,eap2200 |\
 	openmesh,a42 |\
@@ -188,6 +189,7 @@ case "$FIRMWARE" in
 	compex,wpj419 |\
 	compex,wpj428 |\
 	edgecore,ecw5211 |\
+	edgecore,oap100 |\
 	engenius,eap1300 |\
 	engenius,eap2200 |\
 	openmesh,a42 |\

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -67,6 +67,7 @@ platform_do_upgrade() {
 	buffalo,wtr-m2133hp |\
 	cilab,meshpoint-one |\
 	edgecore,ecw5211 |\
+	edgecore,oap100 |\
 	engenius,eap2200 |\
 	mobipromo,cm520-79f |\
 	qxwlan,e2600ac-c2)

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-oap100.dts

@@ -0,0 +1,339 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "EdgeCore OAP-100";
+	compatible = "edgecore,oap100";
+
+	aliases {
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	chosen {
+		bootargs-append = " root=/dev/ubiblock0_1";
+	};
+
+	soc {
+		mdio@90000 {
+			status = "okay";
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		tcsr@194b000 {
+			/* select hostmode */
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+			status = "okay";
+		};
+
+		usb2@60f8800 {
+			status = "okay";
+
+			dwc3@6000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				usb2_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+			};
+		};
+
+		usb3@8af8800 {
+			status = "okay";
+
+			dwc3@8a00000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				usb3_port1: port@1 {
+					reg = <1>;
+					#trigger-source-cells = <0>;
+				};
+
+				usb3_port2: port@2 {
+					reg = <2>;
+					#trigger-source-cells = <0>;
+				};
+			};
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+			switch_mac_mode = <0x0>; /* mac mode for RGMII RMII */
+			switch_initvlas = <0x0007c 0x54>; /* port0 status */
+			switch_lan_bmp = <0x10>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	key {
+		compatible = "gpio-keys";
+
+		button@1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_system: led_system {
+			label = "oap100:green:system";
+			gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_2g {
+			label = "oap100:blue:wlan2g";
+			gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_5g {
+			label = "oap100:blue:wlan5g";
+			gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		usb {
+			gpio-export,name = "usb-power";
+			gpio-export,output = <1>;
+			gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+		};
+
+		poe {
+			gpio-export,name = "poe-power";
+			gpio-export,output = <0>;
+			gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&tlmm {
+	serial_0_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	nand_pins: nand_pins {
+		pullups {
+			pins = "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56",
+				"gpio57", "gpio60", "gpio61",
+				"gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67",
+				"gpio68", "gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio6";
+			function = "mdio";
+			bias-pull-up;
+		};
+		mux_2 {
+			pins = "gpio7";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		linux,modalias = "m25p80", "gd25q256";
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition0@0 {
+				label = "0:SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition1@40000 {
+				label = "0:MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+			partition2@60000 {
+				label = "0:QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+			partition3@c0000 {
+				label = "0:CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+			partition4@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+			partition5@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+			partition6@f0000 {
+				label = "0:APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+			partition7@170000 {
+				label = "0:ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "rootfs";
+				reg = <0x00000000 0x4000000>;
+			};
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "Edgecore OAP100";
+};
+
+&wifi1 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "Edgecore OAP100";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};

target/linux/ipq40xx/image/Makefile

@@ -356,6 +356,19 @@ define Device/edgecore_ecw5211
 endef
 TARGET_DEVICES += edgecore_ecw5211
 
+define Device/edgecore_oap100
+	$(call Device/FitImage)
+	$(call Device/UbiFit)
+	DEVICE_TITLE := Edgecore OAP100
+	BLOCKSIZE := 128k
+	PAGESIZE := 2048
+	IMAGES := nand-sysupgrade.bin
+	DEVICE_DTS_CONFIG := [email protected]
+	DEVICE_DTS := qcom-ipq4019-oap100
+	DEVICE_PACKAGES := ipq-wifi-edgecore_oap100 kmod-usb-acm kmod-usb-net kmod-usb-net-cdc-qmi uqmi
+endef
+TARGET_DEVICES += edgecore_oap100
+
 define Device/engenius_eap1300
 	$(call Device/FitImage)
 	DEVICE_VENDOR := EnGenius

target/linux/ipq40xx/patches-5.4/100-GPIO-add-named-gpio-exports.patch

@@ -0,0 +1,165 @@
+From 4267880319bc1a2270d352e0ded6d6386242a7ef Mon Sep 17 00:00:00 2001
+From: John Crispin <[email protected]>
+Date: Tue, 12 Aug 2014 20:49:27 +0200
+Subject: [PATCH 24/53] GPIO: add named gpio exports
+
+Signed-off-by: John Crispin <[email protected]>
+---
+ drivers/gpio/gpiolib-of.c     |   68 +++++++++++++++++++++++++++++++++++++++++
+ drivers/gpio/gpiolib-sysfs.c  |   10 +++++-
+ include/asm-generic/gpio.h    |    6 ++++
+ include/linux/gpio/consumer.h |    8 +++++
+ 4 files changed, 91 insertions(+), 1 deletion(-)
+
+--- a/drivers/gpio/gpiolib-of.c
++++ b/drivers/gpio/gpiolib-of.c
+@@ -23,6 +23,8 @@
+ #include <linux/pinctrl/pinctrl.h>
+ #include <linux/slab.h>
+ #include <linux/gpio/machine.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
+ 
+ #include "gpiolib.h"
+ 
+@@ -513,3 +515,68 @@ void of_gpiochip_remove(struct gpio_chip
+ 	gpiochip_remove_pin_ranges(chip);
+ 	of_node_put(chip->of_node);
+ }
++
++static struct of_device_id gpio_export_ids[] = {
++	{ .compatible = "gpio-export" },
++	{ /* sentinel */ }
++};
++
++static int of_gpio_export_probe(struct platform_device *pdev)
++{
++	struct device_node *np = pdev->dev.of_node;
++	struct device_node *cnp;
++	u32 val;
++	int nb = 0;
++
++	for_each_child_of_node(np, cnp) {
++		const char *name = NULL;
++		int gpio;
++		bool dmc;
++		int max_gpio = 1;
++		int i;
++
++		of_property_read_string(cnp, "gpio-export,name", &name);
++
++		if (!name)
++			max_gpio = of_gpio_count(cnp);
++
++		for (i = 0; i < max_gpio; i++) {
++			unsigned flags = 0;
++			enum of_gpio_flags of_flags;
++
++			gpio = of_get_gpio_flags(cnp, i, &of_flags);
++			if (!gpio_is_valid(gpio))
++				return gpio;
++
++			if (of_flags == OF_GPIO_ACTIVE_LOW)
++				flags |= GPIOF_ACTIVE_LOW;
++
++			if (!of_property_read_u32(cnp, "gpio-export,output", &val))
++				flags |= val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
++			else
++				flags |= GPIOF_IN;
++
++			if (devm_gpio_request_one(&pdev->dev, gpio, flags, name ? name : of_node_full_name(np)))
++				continue;
++
++			dmc = of_property_read_bool(cnp, "gpio-export,direction_may_change");
++			gpio_export_with_name(gpio, dmc, name);
++			nb++;
++		}
++	}
++
++	dev_info(&pdev->dev, "%d gpio(s) exported\n", nb);
++
++	return 0;
++}
++
++static struct platform_driver gpio_export_driver = {
++	.driver		= {
++		.name		= "gpio-export",
++		.owner	= THIS_MODULE,
++		.of_match_table	= of_match_ptr(gpio_export_ids),
++	},
++	.probe		= of_gpio_export_probe,
++};
++
++module_platform_driver(gpio_export_driver);
+--- a/drivers/gpio/gpiolib-sysfs.c
++++ b/drivers/gpio/gpiolib-sysfs.c
+@@ -553,7 +553,7 @@ static struct class gpio_class = {
+  *
+  * Returns zero on success, else an error.
+  */
+-int gpiod_export(struct gpio_desc *desc, bool direction_may_change)
++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name)
+ {
+ 	struct gpio_chip	*chip;
+ 	struct gpio_device	*gdev;
+@@ -615,6 +615,8 @@ int gpiod_export(struct gpio_desc *desc,
+ 	offset = gpio_chip_hwgpio(desc);
+ 	if (chip->names && chip->names[offset])
+ 		ioname = chip->names[offset];
++	if (name)
++		ioname = name;
+ 
+ 	dev = device_create_with_groups(&gpio_class, &gdev->dev,
+ 					MKDEV(0, 0), data, gpio_groups,
+@@ -636,6 +638,12 @@ err_unlock:
+ 	gpiod_dbg(desc, "%s: status %d\n", __func__, status);
+ 	return status;
+ }
++EXPORT_SYMBOL_GPL(__gpiod_export);
++
++int gpiod_export(struct gpio_desc *desc, bool direction_may_change)
++{
++	return __gpiod_export(desc, direction_may_change, NULL);
++}
+ EXPORT_SYMBOL_GPL(gpiod_export);
+ 
+ static int match_export(struct device *dev, const void *desc)
+--- a/include/asm-generic/gpio.h
++++ b/include/asm-generic/gpio.h
+@@ -127,6 +127,12 @@ static inline int gpio_export(unsigned g
+ 	return gpiod_export(gpio_to_desc(gpio), direction_may_change);
+ }
+ 
++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name);
++static inline int gpio_export_with_name(unsigned gpio, bool direction_may_change, const char *name)
++{
++	return __gpiod_export(gpio_to_desc(gpio), direction_may_change, name);
++}
++
+ static inline int gpio_export_link(struct device *dev, const char *name,
+ 				   unsigned gpio)
+ {
+--- a/include/linux/gpio/consumer.h
++++ b/include/linux/gpio/consumer.h
+@@ -451,6 +451,7 @@ struct gpio_desc *devm_fwnode_get_gpiod_
+ 
+ #if IS_ENABLED(CONFIG_GPIOLIB) && IS_ENABLED(CONFIG_GPIO_SYSFS)
+ 
++int _gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name);
+ int gpiod_export(struct gpio_desc *desc, bool direction_may_change);
+ int gpiod_export_link(struct device *dev, const char *name,
+ 		      struct gpio_desc *desc);
+@@ -458,6 +459,13 @@ void gpiod_unexport(struct gpio_desc *de
+ 
+ #else  /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */
+ 
++static inline int _gpiod_export(struct gpio_desc *desc,
++			       bool direction_may_change,
++			       const char *name)
++{
++	return -ENOSYS;
++}
++
+ static inline int gpiod_export(struct gpio_desc *desc,
+ 			       bool direction_may_change)
+ {

target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch

@@ -12,7 +12,7 @@ Index: linux-5.4.63/arch/arm/boot/dts/Makefile
 ===================================================================
 --- linux-5.4.63.orig/arch/arm/boot/dts/Makefile
 +++ linux-5.4.63/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,51 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,52 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -32,6 +32,7 @@ Index: linux-5.4.63/arch/arm/boot/dts/Makefile
 +	qcom-ipq4018-jalapeno.dtb \
 +	qcom-ipq4018-meshpoint-one.dtb \
 +	qcom-ipq4018-nbg6617.dtb \
++	qcom-ipq4019-oap100.dtb \
 +	qcom-ipq4018-rt-ac58u.dtb \
 +	qcom-ipq4018-wre6606.dtb \
  	qcom-ipq4019-ap.dk01.1-c1.dtb \