ipq40xx: add support for AVM FRITZ!Repeater 3000

Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH:   Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED:    - Connect green/blue/red
        - Power green
BTN:   WPS/Connect
UART:  115200n8 3.3V
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ3000.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz3000.bin uboot0
   > mtd write /path/to/uboot-fritz3000.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <[email protected]>

package/boot/uboot-fritz4040/Makefile

@@ -25,6 +25,11 @@ define U-Boot/Default
   UBOOT_IMAGE:=uboot-$(1).bin
 endef
 
+define U-Boot/fritz3000
+  NAME:=FritzRepeater 3000
+  BUILD_DEVICES:=avm_fritzrepeater-3000
+endef
+
 define U-Boot/fritz4040
   NAME:=FritzBox 4040
   BUILD_DEVICES:=avm_fritzbox-4040
@@ -61,6 +66,6 @@ define Package/u-boot/install
 	$(INSTALL_BIN) $(PKG_BUILD_DIR)/upload-to-f4040.sh $(1)/
 endef
 
-UBOOT_TARGETS := fritz4040 fritz7530
+UBOOT_TARGETS := fritz3000 fritz4040 fritz7530
 
 $(eval $(call BuildPackage/U-Boot))

package/firmware/ipq-wifi/Makefile

@@ -18,7 +18,7 @@ endef
 # Please send a mail with your device-specific board files upstream.
 # You can find instructions and examples on the linux-wireless wiki:
 # <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
-ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 avm_fritzbox-7530 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
+ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 avm_fritzbox-7530 avm_fritzrepeater-3000 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
 
 define Package/ipq-wifi-default
@@ -57,6 +57,7 @@ $(eval $(call generate-ipq-wifi-package,alfa-network_ap120c-ac,board-alfa-networ
 $(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200))
 $(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300))
 $(eval $(call generate-ipq-wifi-package,avm_fritzbox-7530,board-avm_fritzbox-7530.bin,AVM FRITZ!Box 7530))
+$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-3000,board-avm_fritzrepeater-3000.bin,AVM FRITZ!Repeater 3000))
 $(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3))
 $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,board-qxwlan-e2600ac.bin,Qxwlan E2600AC))
 

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -37,6 +37,7 @@ ipq40xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
 		;;
+	avm,fritzrepeater-3000|\
 	compex,wpj428)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;

target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -111,6 +111,10 @@ case "$FIRMWARE" in
 		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
 			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
 		;;
+	avm,fritzrepeater-3000)
+		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+		/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+		;;
 	openmesh,a62)
 		ath10kcal_extract "0:ART" 36864 12064
 		;;
@@ -135,7 +139,8 @@ case "$FIRMWARE" in
 	avm,fritzbox-4040)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
 		;;
-	avm,fritzbox-7530)
+	avm,fritzbox-7530 |\
+	avm,fritzrepeater-3000)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
@@ -183,7 +188,8 @@ case "$FIRMWARE" in
 	avm,fritzbox-4040)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
 		;;
-	avm,fritzbox-7530)
+	avm,fritzbox-7530 |\
+	avm,fritzrepeater-3000)
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -49,6 +49,7 @@ platform_do_upgrade() {
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	avm,fritzbox-7530 |\
+	avm,fritzrepeater-3000|\
 	qxwlan,e2600ac-c2)
 		nand_do_upgrade "$ARGV"
 		;;

target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts

@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "AVM FRITZ!Repeater 3000";
+	compatible = "avm,fritzrepeater-3000";
+
+	aliases {
+		led-boot = &power_led;
+		led-failsafe = &power_led;
+		led-running = &power_led;
+		led-upgrade = &power_led;
+	};
+
+	soc {
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+
+			switch_lan_bmp = <0x10>;
+			switch_wan_bmp = <0x20>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	key {
+		compatible = "gpio-keys";
+
+		connect {
+			label = "Connect";
+			gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		connect_red {
+			label = "fritzwlan-3000:red:connect";
+			gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+		};
+
+		connect_green {
+			label = "fritzwlan-3000:green:connect";
+			gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+		};
+
+		connect_blue {
+			label = "fritzwlan-3000:blue:connect";
+			gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+		};
+
+		power_led: power {
+			label = "fritzwlan-3000:green:power";
+			gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&tlmm {
+	serial_0_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	nand_pins: nand_pins {
+		pullups {
+			pins = "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56",
+				"gpio57", "gpio60", "gpio61",
+				"gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67",
+				"gpio68", "gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x000000 0x80000>;
+				read-only;
+			};
+
+			partition@80000 {
+				label = "MIBIB";
+				reg = <0x080000 0x80000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "QSEE";
+				reg = <0x100000 0x80000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "CDT";
+				reg = <0x180000 0x40000>;
+				read-only;
+			};
+
+			partition@1c0000 {
+				label = "QSEE_B";
+				reg = <0x1c0000 0x80000>;
+				read-only;
+			};
+
+			partition@240000 {
+				label = "urlader0";
+				reg = <0x240000 0x40000>;
+				read-only;
+			};
+
+			partition@280000 {
+				label = "urlader1";
+				reg = <0x280000 0x40000>;
+				read-only;
+			};
+
+			partition@2c0000 {
+				label = "nand-tffs";
+				reg = <0x2c0000 0x840000>;
+				read-only;
+			};
+
+			partition@b00000 {
+				/* 'kernel1' in AVM firmware */
+				label = "uboot0";
+				reg = <0xb00000 0x400000>;
+			};
+
+			partition@f00000 {
+				/* 'kernel2' in AVM firmware */
+				label = "uboot1";
+				reg = <0xf00000 0x400000>;
+			};
+
+			partition@1300000 {
+				label = "ubi";
+				reg = <0x1300000 0x6d00000>;
+			};
+		};
+	};
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+	qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
+};
+
+&wifi1 {
+	status = "okay";
+	ieee80211-freq-limit = <5170000 5350000>;
+	/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+	qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
+};
+
+&pcie0 {
+	status = "okay";
+
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@1,0 {
+			/* QCA9984 */
+			compatible = "qcom,ath10k";
+			status = "okay";
+			reg = <0x00010000 0 0 0 0>;
+			ieee80211-freq-limit = <5470000 5875000>;
+			/* Uses the reference BDF */
+		};
+	};
+};

target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzrepeater-3000.dts

@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "AVM FRITZ!Repeater 3000";
+	compatible = "avm,fritzrepeater-3000";
+
+	aliases {
+		led-boot = &power_led;
+		led-failsafe = &power_led;
+		led-running = &power_led;
+		led-upgrade = &power_led;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+
+			switch_lan_bmp = <0x10>;
+			switch_wan_bmp = <0x20>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	key {
+		compatible = "gpio-keys";
+
+		connect {
+			label = "Connect";
+			gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		connect_red {
+			label = "fritzwlan-3000:red:connect";
+			gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+		};
+
+		connect_green {
+			label = "fritzwlan-3000:green:connect";
+			gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+		};
+
+		connect_blue {
+			label = "fritzwlan-3000:blue:connect";
+			gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+		};
+
+		power_led: power {
+			label = "fritzwlan-3000:green:power";
+			gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&tlmm {
+	serial_0_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	nand_pins: nand_pins {
+		pullups {
+			pins = "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56",
+				"gpio57", "gpio60", "gpio61",
+				"gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67",
+				"gpio68", "gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x000000 0x80000>;
+				read-only;
+			};
+
+			partition@80000 {
+				label = "MIBIB";
+				reg = <0x080000 0x80000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "QSEE";
+				reg = <0x100000 0x80000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "CDT";
+				reg = <0x180000 0x40000>;
+				read-only;
+			};
+
+			partition@1c0000 {
+				label = "QSEE_B";
+				reg = <0x1c0000 0x80000>;
+				read-only;
+			};
+
+			partition@240000 {
+				label = "urlader0";
+				reg = <0x240000 0x40000>;
+				read-only;
+			};
+
+			partition@280000 {
+				label = "urlader1";
+				reg = <0x280000 0x40000>;
+				read-only;
+			};
+
+			partition@2c0000 {
+				label = "nand-tffs";
+				reg = <0x2c0000 0x840000>;
+				read-only;
+			};
+
+			partition@b00000 {
+				/* 'kernel1' in AVM firmware */
+				label = "uboot0";
+				reg = <0xb00000 0x400000>;
+			};
+
+			partition@f00000 {
+				/* 'kernel2' in AVM firmware */
+				label = "uboot1";
+				reg = <0xf00000 0x400000>;
+			};
+
+			partition@1300000 {
+				label = "ubi";
+				reg = <0x1300000 0x6d00000>;
+			};
+		};
+	};
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+	qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
+};
+
+&wifi1 {
+	status = "okay";
+	ieee80211-freq-limit = <5170000 5350000>;
+	/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+	qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
+};
+
+&pcie0 {
+	status = "okay";
+
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi@1,0 {
+			/* QCA9984 */
+			compatible = "qcom,ath10k";
+			status = "okay";
+			reg = <0x00010000 0 0 0 0>;
+			ieee80211-freq-limit = <5470000 5875000>;
+			/* Uses the reference BDF */
+		};
+	};
+};

target/linux/ipq40xx/image/Makefile

@@ -130,6 +130,15 @@ define Device/avm_fritzbox-7530
 endef
 TARGET_DEVICES += avm_fritzbox-7530
 
+define Device/avm_fritzrepeater-3000
+	$(call Device/FitImageLzma)
+	DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
+	DEVICE_TITLE := AVM Fritz!Repeater 3000
+	DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-3000
+	IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzrepeater-3000
+
 define Device/compex_wpj428
 	$(call Device/FitImage)
 	DEVICE_DTS := qcom-ipq4028-wpj428

target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <[email protected]>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,28 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -29,6 +29,7 @@ Signed-off-by: John Crispin <[email protected]>
 +	qcom-ipq4019-a62.dtb \
 +	qcom-ipq4019-ap.dk04.1-c1.dtb \
 +	qcom-ipq4019-fritzbox-7530.dtb \
++	qcom-ipq4019-fritzrepeater-3000.dtb \
 +	qcom-ipq4019-map-ac2200.dtb \
 +	qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
 +	qcom-ipq4019-qxwlan-e2600ac-c2.dtb \

target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <[email protected]>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,31 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -32,6 +32,7 @@ Signed-off-by: John Crispin <[email protected]>
  	qcom-ipq4019-ap.dk07.1-c2.dtb \
 +	qcom-ipq4019-a62.dtb \
 +	qcom-ipq4019-fritzbox-7530.dtb \
++	qcom-ipq4019-fritzrepeater-3000.dtb \
 +	qcom-ipq4019-map-ac2200.dtb \
 +	qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
 +	qcom-ipq4019-qxwlan-e2600ac-c2.dtb \