ramips: convert TP-Link MT7620 boards to tpt trigger

This converts all MediaTek MT7620 boards from TP-Link to use the now
supported WiFi throughput LED trigger. This way, the LED state now
covers all VAPs regardless of their name.

Also align all single-WiFi LEDs to represent the state of the 2.4GHz
radio. This was not always the case previously, as later-added support
for the MT7610 altered the phy probing order.

Signed-off-by: David Bauer <[email protected]>

target/linux/ramips/dts/mt7620a_tplink_archer-c2-v1.dts

@@ -48,6 +48,7 @@
 		wlan {
 			label = "archer-c2-v1:green:wlan";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
 		};
 	};
 

target/linux/ramips/dts/mt7620a_tplink_archer-c20-v1.dts

@@ -47,11 +47,13 @@
 		wlan5g {
 			label = "archer-c20-v1:blue:wlan5g";
 			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
 		};
 
 		wlan2g {
 			label = "archer-c20-v1:blue:wlan2g";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
 		};
 
 		wps {

target/linux/ramips/dts/mt7620a_tplink_archer-c20i.dts

@@ -38,6 +38,7 @@
 		wlan {
 			label = "archer-c20i:blue:wlan";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
 		};
 	};
 };

target/linux/ramips/dts/mt7620a_tplink_archer-c50-v1.dts

@@ -47,11 +47,13 @@
 		wlan5g {
 			label = "archer-c50-v1:green:wlan5g";
 			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
 		};
 
 		wlan2g {
 			label = "archer-c50-v1:green:wlan2g";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
 		};
 
 		wps {

target/linux/ramips/dts/mt7620a_tplink_archer-mr200.dts

@@ -71,6 +71,7 @@
 		wlan {
 			label = "archer-mr200:white:wlan";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
 		};
 	};
 

target/linux/ramips/dts/mt7620a_tplink_re200-v1.dts

@@ -53,7 +53,7 @@
 		wlan2g_green {
 			label = "re200-v1:green:wlan2g";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "phy1radio";
+			linux,default-trigger = "phy1tpt";
 		};
 	};
 

target/linux/ramips/mt7620/base-files/etc/board.d/01_leds

@@ -168,28 +168,22 @@ zbtlink,zbt-we826-e)
 tplink,archer-c2-v1)
 	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch1" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch1" "0x01"
-	set_wifi_led "$boardname:green:wlan"
 	;;
 tplink,archer-c20-v1)
 	ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01"
-	ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:blue:wlan2g" "wlan0"
 	;;
 tplink,archer-c20i)
 	ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01"
-	ucidef_set_led_wlan "wlan" "wlan" "$boardname:blue:wlan" "phy0radio"
 	;;
 tplink,archer-c50-v1)
 	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
-	ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan2g" wlan1
-	set_wifi_led "$boardname:green:wlan5g"
 	;;
 tplink,archer-mr200)
 	ucidef_set_led_netdev "lan" "lan" "$boardname:white:lan" "eth0.1"
 	ucidef_set_led_netdev "wan" "wan" "$boardname:white:wan" "usb0"
-	set_wifi_led "$boardname:white:wlan"
 	;;
 tplink,re200-v1)
 	ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" "eth0"