ar71xx: add support for the devolo dLAN pro 1200+ WiFi ac

Signed-off-by: Günther Kelleter <[email protected]>

SVN-Revision: 46342

target/linux/ar71xx/base-files/etc/diag.sh

@@ -78,6 +78,9 @@ get_status_led() {
 	dlan-pro-500-wp)
 		status_led="devolo:green:wlan-2g"
 		;;
+	dlan-pro-1200-ac)
+		status_led="devolo:status:wlan"
+		;;
 	dragino2)
 		status_led="dragino2:red:system"
 		;;

target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -47,6 +47,9 @@ board=$(ar71xx_board_name)
 case "$FIRMWARE" in
 "ath10k/cal-pci-0000:00:00.0.bin")
 	case $board in
+	dlan-pro-1200-ac)
+		ath10kcal_extract "art" 20480 2116
+		;;
 	mc-mac1200r)
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)

target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

@@ -180,6 +180,12 @@ dlan-pro-500-wp)
 	ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "devolo:blue:wlan-5g" "none"
 	;;
 
+dlan-pro-1200-ac)
+	ucidef_set_led_wlan "wlan" "WLAN" "devolo:status:wlan" "phy0radio"
+	ucidef_set_led_trigger_gpio "plcw" "dLAN" "devolo:status:dlan" "17" "0"
+	ucidef_set_led_trigger_gpio "plcr" "dLAN" "devolo:error:dlan" "16" "0"
+	;;
+
 gl-inet)
 	ucidef_set_led_netdev "lan" "LAN" "gl-connect:green:lan" "eth1"
 	ucidef_set_led_wlan "wlan" "WLAN" "gl-connect:red:wlan" "phy0tpt"

target/linux/ar71xx/base-files/etc/uci-defaults/02_network

@@ -305,6 +305,12 @@ dlan-pro-500-wp)
 	ucidef_set_interface_lan "eth0 eth1"
 	;;
 
+dlan-pro-1200-ac)
+	ucidef_set_interface_lan "eth0"
+	ucidef_add_switch "switch0" "1" "0"
+	ucidef_add_switch_vlan "switch0" "0" "0 2 3 4"
+	;;
+
 all0305 |\
 aw-nr580 |\
 bullet-m |\

target/linux/ar71xx/base-files/lib/ar71xx.sh

@@ -426,6 +426,9 @@ ar71xx_board_detect() {
 	*"dLAN pro 500 Wireless+")
 		name="dlan-pro-500-wp"
 		;;
+	*"dLAN pro 1200+ WiFi ac")
+		name="dlan-pro-1200-ac"
+		;;
 	*"Dragino v2")
 		name="dragino2"
 		;;

target/linux/ar71xx/base-files/lib/upgrade/platform.sh

@@ -209,6 +209,7 @@ platform_check_image() {
 	dir-825-c1 | \
 	dir-835-a1 | \
 	dlan-pro-500-wp | \
+	dlan-pro-1200-ac | \
 	dragino2 | \
 	epg5000 | \
 	esr1750 | \

target/linux/ar71xx/config-3.18

@@ -56,6 +56,7 @@ CONFIG_ATH79_MACH_DIR_615_C1=y
 CONFIG_ATH79_MACH_DIR_615_I1=y
 CONFIG_ATH79_MACH_DIR_825_B1=y
 CONFIG_ATH79_MACH_DIR_825_C1=y
+CONFIG_ATH79_MACH_DLAN_PRO_1200_AC=y
 CONFIG_ATH79_MACH_DLAN_PRO_500_WP=y
 CONFIG_ATH79_MACH_DRAGINO2=y
 CONFIG_ATH79_MACH_EAP300V2=y

target/linux/ar71xx/files/arch/mips/ath79/mach-dlan-pro-1200-ac.c

@@ -0,0 +1,189 @@
+/*
+ * devolo dLAN pro 500 Wireless+ support
+ *
+ * Copyright (c) 2013-2015 devolo AG
+ * Copyright (c) 2011-2012 Gabor Juhos <[email protected]>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-nfc.h"
+#include "dev-spi.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define DLAN_PRO_1200_AC_GPIO_DLAN_POWER_ENABLE		13
+#define DLAN_PRO_1200_AC_GPIO_WLAN_POWER_ENABLE		21
+#define DLAN_PRO_1200_AC_GPIO_LED_WLAN		12
+#define DLAN_PRO_1200_AC_GPIO_LED_DLAN			14
+#define DLAN_PRO_1200_AC_GPIO_LED_DLAN_ERR			15
+
+#define DLAN_PRO_1200_AC_GPIO_BTN_WLAN			20
+#define DLAN_PRO_1200_AC_GPIO_BTN_DLAN			22
+#define DLAN_PRO_1200_AC_GPIO_BTN_RESET			4
+#define DLAN_PRO_1200_AC_GPIO_DLAN_IND          17
+#define DLAN_PRO_1200_AC_GPIO_DLAN_ERR_IND      16
+
+#define DLAN_PRO_1200_AC_KEYS_POLL_INTERVAL		20	/* msecs */
+#define DLAN_PRO_1200_AC_KEYS_DEBOUNCE_INTERVAL		(3 * DLAN_PRO_1200_AC_KEYS_POLL_INTERVAL)
+
+#define DLAN_PRO_1200_AC_ART_ADDRESS			0x1fff0000
+#define DLAN_PRO_1200_AC_CALDATA_OFFSET			0x1000
+#define DLAN_PRO_1200_AC_WIFIMAC_OFFSET			0x1002
+#define DLAN_PRO_1200_AC_PCIE_CALDATA_OFFSET	0x5000
+
+static struct gpio_led dlan_pro_1200_ac_leds_gpio[] __initdata = {
+	{
+		.name		        = "devolo:status:wlan",
+		.gpio		        = DLAN_PRO_1200_AC_GPIO_LED_WLAN,
+		.active_low	        = 1,
+	},
+	{
+		.name		        = "devolo:status:dlan",
+		.gpio		        = DLAN_PRO_1200_AC_GPIO_LED_DLAN,
+		.active_low	        = 1,
+	},
+	{
+		.name		        = "devolo:error:dlan",
+		.gpio		        = DLAN_PRO_1200_AC_GPIO_LED_DLAN_ERR,
+		.active_low	        = 0,
+	}
+};
+
+static struct gpio_keys_button dlan_pro_1200_ac_gpio_keys[] __initdata = {
+	{
+		.desc		= "dLAN button",
+		.type		= EV_KEY,
+		.code		= BTN_0,
+		.debounce_interval = DLAN_PRO_1200_AC_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= DLAN_PRO_1200_AC_GPIO_BTN_DLAN,
+		.active_low	= 1,
+	},
+	{
+		.desc		= "WLAN button",
+		.type		= EV_KEY,
+		.code		= KEY_WPS_BUTTON,
+		.debounce_interval = DLAN_PRO_1200_AC_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= DLAN_PRO_1200_AC_GPIO_BTN_WLAN,
+		.active_low	= 0,
+	},
+	{
+		.desc		= "Reset button",
+		.type		= EV_KEY,
+		.code		= KEY_RESTART,
+		.debounce_interval = DLAN_PRO_1200_AC_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= DLAN_PRO_1200_AC_GPIO_BTN_RESET,
+		.active_low	= 1,
+	}
+};
+
+static struct ar8327_pad_cfg dlan_pro_1200_ac_ar8327_pad0_cfg = {
+	.mode = AR8327_PAD_MAC_RGMII,
+	.txclk_delay_en = true,
+	.rxclk_delay_en = false,
+	.txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
+	.rxclk_delay_sel = AR8327_CLK_DELAY_SEL0,
+};
+
+static struct ar8327_pad_cfg dlan_pro_1200_ac_ar8327_pad5_cfg = {
+	.mode = 0,
+	.txclk_delay_en = 0,
+	.rxclk_delay_en = 0,
+	.txclk_delay_sel = 0,
+	.rxclk_delay_sel = 0,
+};
+
+static struct ar8327_platform_data dlan_pro_1200_ac_ar8327_data = {
+	.pad0_cfg = &dlan_pro_1200_ac_ar8327_pad0_cfg,
+	.pad5_cfg = &dlan_pro_1200_ac_ar8327_pad5_cfg,
+	.port0_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+};
+
+static struct mdio_board_info dlan_pro_1200_ac_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 0,
+		.platform_data = &dlan_pro_1200_ac_ar8327_data,
+	},
+};
+
+static void __init dlan_pro_1200_ac_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(DLAN_PRO_1200_AC_ART_ADDRESS);
+	u8 *cal = art + DLAN_PRO_1200_AC_CALDATA_OFFSET;
+	u8 *wifi_mac = art + DLAN_PRO_1200_AC_WIFIMAC_OFFSET;
+
+	ath79_register_m25p80(NULL);
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(dlan_pro_1200_ac_leds_gpio),
+				 dlan_pro_1200_ac_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, DLAN_PRO_1200_AC_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(dlan_pro_1200_ac_gpio_keys),
+					dlan_pro_1200_ac_gpio_keys);
+
+	/* dLAN power must be enabled from user-space as soon as the boot-from-host daemon is running */
+	gpio_request_one(DLAN_PRO_1200_AC_GPIO_DLAN_POWER_ENABLE,
+			 GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
+			 "dLAN power");
+
+	/* WLAN power is turned on initially to allow the PCI bus scan to succeed */
+	gpio_request_one(DLAN_PRO_1200_AC_GPIO_WLAN_POWER_ENABLE,
+			 GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
+			 "WLAN power");
+
+	ath79_register_wmac(cal, wifi_mac);
+	ap91_pci_init(art + DLAN_PRO_1200_AC_PCIE_CALDATA_OFFSET, NULL);
+
+	ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE);
+
+	ath79_register_mdio(1, 0x0);
+	ath79_register_mdio(0, 0x0);
+
+	ath79_init_mac(ath79_eth0_data.mac_addr, wifi_mac, 2);
+
+	mdiobus_register_board_info(dlan_pro_1200_ac_mdio0_info,
+				    ARRAY_SIZE(dlan_pro_1200_ac_mdio0_info));
+
+	/* GMAC0 is connected to an AR8337 */
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+	ath79_eth0_pll_data.pll_1000 = 0x02000000;
+	ath79_register_eth(0);
+}
+
+MIPS_MACHINE(ATH79_MACH_DLAN_PRO_1200_AC, "dLAN-pro-1200-ac", "devolo dLAN pro 1200+ WiFi ac",
+	     dlan_pro_1200_ac_setup);

target/linux/ar71xx/generic/profiles/devolo-dlan.mk

@@ -17,3 +17,17 @@ define Profile/dLAN_pro_500_wp/Description
 	Package set optimized for the devolo dLAN pro 500 Wireless+.
 endef
 $(eval $(call Profile,dLAN_pro_500_wp))
+
+define Profile/dLAN_pro_1200_ac
+	NAME:=devolo dLAN pro 1200+ WiFi ac
+	PACKAGES:=open-plc-utils open-plc-utils-chkpib open-plc-utils-getpib open-plc-utils-modpib \
+		open-plc-utils-setpib open-plc-utils-hpavkey open-plc-utils-plchost \
+		open-plc-utils-plctool open-plc-utils-pibdump open-plc-utils-plcstat \
+		ebtables hostapd-utils wifitoggle wpad ip-full kmod-ath10k kmod-leds-gpio \
+		kmod-ledtrig-gpio
+endef
+
+define Profile/dLAN_pro_1200_ac/Description
+	Package set optimized for the devolo dLAN pro 1200+ WiFi ac.
+endef
+$(eval $(call Profile,dLAN_pro_1200_ac))

target/linux/ar71xx/image/Makefile

@@ -1186,6 +1186,7 @@ eap300v2_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),320k(custom),1
 db120_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1408k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware)
 dgl_5500_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(nvram)ro,15296k(firmware),192k(lang)ro,512k(my-dlink)ro,64k(mac)ro,64k(art)ro
 dlan_pro_500_wp_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(Config1)ro,64k(Config2)ro,1152k@0x70000(kernel),6528k(rootfs),7680k@0x70000(firmware),64k(art)ro
+dlan_pro_1200_ac_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(Config1)ro,64k(Config2)ro,1152k@0x70000(kernel),14720k(rootfs),15872k@0x70000(firmware),64k(art)ro
 cameo_ap94_mtdlayout=mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,6208k(firmware),64k(caldata)ro,1600k(unknown)ro,64k@0x7f0000(caldata_copy)
 cameo_ap94_mtdlayout_fat=mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,7808k(firmware),64k(caldata)ro,64k@0x660000(caldata_orig),6208k@0x50000(firmware_orig)
 esr900_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),13248k(rootfs),1024k(manufacture)ro,64k(backup)ro,320k(storage)ro,64k(caldata)ro,14656k@0x40000(firmware)
@@ -2081,6 +2082,7 @@ $(eval $(call SingleProfile,CameoAP94,64kraw,TEW673GRU,tew-673gru,TEW-673GRU,tty
 $(eval $(call SingleProfile,CameoAP94,64kraw,DLRTDEV01,dlrtdev01,DIR-825-B1,ttyS0,115200,$$(dlrtdev_mtdlayout),$$(dlrtdev_mtdlayout_fat),01AP94-AR7161-RT-080619-00,00AP94-AR7161-RT-080619-00))
 
 $(eval $(call SingleProfile,dLANLzma,64k,dLAN_pro_500_wp,dlan-pro-500-wp,dLAN-pro-500-wp,ttyS0,115200,$$(dlan_pro_500_wp_mtdlayout) root=31:5 mem=128M,KRuImage))
+$(eval $(call SingleProfile,dLANLzma,64k,dLAN_pro_1200_ac,dlan-pro-1200-ac,dLAN-pro-1200-ac,ttyS0,115200,$$(dlan_pro_1200_ac_mtdlayout) root=31:5 mem=128M,KRuImage))
 
 $(eval $(call SingleProfile,EnGenius,64k,ESR900,esr900,ESR900,ttyS0,115200,$$(esr900_mtdlayout),KRuImage,,0x4e))
 $(eval $(call SingleProfile,EnGenius,64k,ESR1750,esr1750,ESR1750,ttyS0,115200,$$(esr1750_mtdlayout),KRuImage,,0x61))

target/linux/ar71xx/patches-3.18/610-MIPS-ath79-openwrt-machines.patch

@@ -1,6 +1,6 @@
 --- a/arch/mips/ath79/machtypes.h
 +++ b/arch/mips/ath79/machtypes.h
-@@ -16,22 +16,194 @@
+@@ -16,22 +16,195 @@
  
  enum ath79_mach_type {
  	ATH79_MACH_GENERIC = 0,
@@ -40,6 +40,7 @@
 +	ATH79_MACH_DIR_825_C1,		/* D-Link DIR-825 rev. C1 */
 +	ATH79_MACH_DIR_835_A1,		/* D-Link DIR-835 rev. A1 */
 +	ATH79_MACH_DLAN_PRO_500_WP,	/* devolo dLAN pro 500 Wireless+ */
++	ATH79_MACH_DLAN_PRO_1200_AC,	/* devolo dLAN pro 1200+ WiFi ac*/
 +	ATH79_MACH_DRAGINO2,		/* Dragino Version 2 */
 +	ATH79_MACH_ESR900,		/* EnGenius ESR900 */
 +	ATH79_MACH_EW_DORIN,		/* embedded wireless Dorin Platform */
@@ -268,7 +269,7 @@
  config ATH79_MACH_AP121
  	bool "Atheros AP121 reference board"
  	select SOC_AR933X
-@@ -11,62 +75,1018 @@ config ATH79_MACH_AP121
+@@ -11,62 +75,1031 @@ config ATH79_MACH_AP121
  	select ATH79_DEV_M25P80
  	select ATH79_DEV_USB
  	select ATH79_DEV_WMAC
@@ -627,6 +628,19 @@
 +	select ATH79_DEV_WMAC
 +	select ATH79_DEV_USB
 +
++config ATH79_MACH_DLAN_PRO_1200_AC
++	bool "devolo dLAN pro 1200+ WiFi ac support"
++	select SOC_AR934X
++	select ATH79_DEV_AP9X_PCI if PCI
++	select ATH79_DEV_ETH
++	select ATH79_DEV_GPIO_BUTTONS
++	select ATH79_DEV_LEDS_GPIO
++	select ATH79_DEV_SPI
++	select ATH79_DEV_M25P80
++	select ATH79_DEV_WMAC
++	select ATH79_DEV_NFC
++	select ATH79_DEV_USB
++
 +config ATH79_MACH_DRAGINO2
 +	bool "DRAGINO V2 support"
 +	select SOC_AR933X
@@ -1315,7 +1329,7 @@
  
  config ATH79_MACH_UBNT_XM
  	bool "Ubiquiti Networks XM/UniFi boards"
-@@ -83,6 +1103,97 @@ config ATH79_MACH_UBNT_XM
+@@ -83,6 +1116,97 @@ config ATH79_MACH_UBNT_XM
  	  Say 'Y' here if you want your kernel to support the
  	  Ubiquiti Networks XM (rev 1.0) board.
  
@@ -1413,7 +1427,7 @@
  endmenu
  
  config SOC_AR71XX
-@@ -124,7 +1235,10 @@ config ATH79_DEV_DSA
+@@ -124,7 +1248,10 @@ config ATH79_DEV_DSA
  config ATH79_DEV_ETH
  	def_bool n
  
@@ -1425,7 +1439,7 @@
  	def_bool n
  
  config ATH79_DEV_GPIO_BUTTONS
-@@ -154,6 +1268,11 @@ config ATH79_PCI_ATH9K_FIXUP
+@@ -154,6 +1281,11 @@ config ATH79_PCI_ATH9K_FIXUP
  	def_bool n
  
  config ATH79_ROUTERBOOT
@@ -1439,7 +1453,7 @@
  endif
 --- a/arch/mips/ath79/Makefile
 +++ b/arch/mips/ath79/Makefile
-@@ -38,9 +38,123 @@ obj-$(CONFIG_ATH79_ROUTERBOOT)		+= route
+@@ -38,9 +38,124 @@ obj-$(CONFIG_ATH79_ROUTERBOOT)		+= route
  #
  # Machines
  #
@@ -1461,6 +1475,7 @@
 +obj-$(CONFIG_ATH79_MACH_CPE510)		+= mach-cpe510.o
  obj-$(CONFIG_ATH79_MACH_DB120)		+= mach-db120.o
 +obj-$(CONFIG_ATH79_MACH_DLAN_PRO_500_WP)	+= mach-dlan-pro-500-wp.o
++obj-$(CONFIG_ATH79_MACH_DLAN_PRO_1200_AC)	+= mach-dlan-pro-1200-ac.o
 +obj-$(CONFIG_ATH79_MACH_DGL_5500_A1)	+= mach-dgl-5500-a1.o
 +obj-$(CONFIG_ATH79_MACH_DHP_1565_A1)	+= mach-dhp-1565-a1.o
 +obj-$(CONFIG_ATH79_MACH_DIR_505_A1)	+= mach-dir-505-a1.o