mediatek: add support for TP-Link TL-XDR4288/608x

Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: ESMT M15T4G16256A 512MB
  Ethernet (Max Speed):
    XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
    XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
    XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
  WiFi:
    XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
    XDR6086/XDR6088:
      WiFi1: MT7976GN 2.4GHz 4T4R
      WiFi2: MT7976AN 5GHz 4T4R
  Button: Reset, WPS, Turbo
  USB: 1 x USB 3.0
  Power: DC 12V 4A

Flash instructions:
  1. Execute the following operation to open nc shell:
     https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
  2. Replace the stock bootloader to OpenWrt's:
     dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
     dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
  3. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  4. Download the initramfs image, and restart the router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Signed-off-by: Chukun Pan <[email protected]>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <[email protected]>

target/linux/mediatek/dts/mt7986a-tplink-tl-xdr-common.dtsi

@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	aliases {
+		serial0 = &uart0;
+		label-mac-device = &gmac0;
+		led-boot = &led_status_green;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_green;
+		led-upgrade = &led_status_red;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x20000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+
+		turbo {
+			label = "turbo";
+			linux,code = <BTN_1>;
+			gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: status_red {
+			label = "red:status";
+			gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_status_green: status_green {
+			label = "green:status";
+			gpios = <&pio 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		turbo {
+			label = "green:turbo";
+			gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		nvmem-cells = <&macaddr_config_1c>;
+		nvmem-cell-names = "mac-address";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-handle = <&phy7>;
+		phy-mode = "2500base-x";
+
+		nvmem-cells = <&macaddr_config_1c>;
+		nvmem-cell-names = "mac-address";
+		mac-address-increment = <1>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	phy5: ethernet-phy@5 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <5>;
+		reset-assert-us = <100000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+		realtek,aldps-enable;
+	};
+
+	phy7: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <7>;
+		reset-assert-us = <100000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&pio 17 GPIO_ACTIVE_LOW>;
+		realtek,aldps-enable;
+	};
+
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+
+		spi-max-frequency = <20000000>;
+		spi-tx-buswidth = <4>;
+		spi-rx-buswidth = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bl2";
+				reg = <0x000000 0x0100000>;
+				read-only;
+			};
+
+			config: partition@100000 {
+				label = "config";
+				reg = <0x100000 0x0060000>;
+				read-only;
+			};
+
+			factory: partition@160000 {
+				label = "factory";
+				reg = <0x160000 0x0060000>;
+				read-only;
+			};
+
+			partition@1c0000 {
+				label = "reserved";
+				reg = <0x1c0000 0x01c0000>;
+				read-only;
+			};
+
+			partition@380000 {
+				label = "fip";
+				reg = <0x380000 0x0200000>;
+				read-only;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x580000 0x7800000>;
+			};
+		};
+	};
+};
+
+&pio {
+	spi_flash_pins: spi-flash-pins-33-to-38 {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <8>;
+			mediatek,pull-down-adv = <0>; /* bias-disable */
+		};
+	};
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&wmac {
+	mediatek,mtd-eeprom = <&factory 0x0>;
+	nvmem-cells = <&macaddr_config_1c>;
+	nvmem-cell-names = "mac-address";
+	mac-address-increment = <2>;
+	status = "okay";
+};
+
+&config {
+	compatible = "nvmem-cells";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	macaddr_config_1c: macaddr@1c {
+		reg = <0x1c 0x6>;
+	};
+};

target/linux/mediatek/dts/mt7986a-tplink-tl-xdr4288.dts

@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include "mt7986a-tplink-tl-xdr-common.dtsi"
+
+/ {
+	model = "TP-Link TL-XDR4288";
+	compatible = "tplink,tl-xdr4288", "mediatek,mt7986a";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "lan5";
+			phy-handle = <&phy5>;
+			phy-mode = "2500base-x";
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
+
+&wmac {
+	pinctrl-names = "dbdc";
+	pinctrl-0 = <&wf_dbdc_pins>;
+};

target/linux/mediatek/dts/mt7986a-tplink-tl-xdr6086.dts

@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include "mt7986a-tplink-tl-xdr-common.dtsi"
+
+/ {
+	model = "TP-Link TL-XDR6086";
+	compatible = "tplink,tl-xdr6086", "mediatek,mt7986a";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "lan2";
+			phy-handle = <&phy5>;
+			phy-mode = "2500base-x";
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
+
+&wmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+};

target/linux/mediatek/dts/mt7986a-tplink-tl-xdr6088.dts

@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include "mt7986a-tplink-tl-xdr-common.dtsi"
+
+/ {
+	model = "TP-Link TL-XDR6088";
+	compatible = "tplink,tl-xdr6088", "mediatek,mt7986a";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "lan5";
+			phy-handle = <&phy5>;
+			phy-mode = "2500base-x";
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
+
+&wmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+};

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -20,6 +20,13 @@ mediatek_setup_interfaces()
 	mediatek,mt7986b-rfb)
 		ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" eth1
 		;;
+	tplink,tl-xdr4288|\
+	tplink,tl-xdr6088)
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" eth1
+		;;
+	tplink,tl-xdr6086)
+		ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
+		;;
 	xiaomi,redmi-router-ax6000-stock|\
 	xiaomi,redmi-router-ax6000-ubootmod)
 		ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan

target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac

@@ -24,4 +24,9 @@ case "$board" in
 		[ "$PHYNBR" = "0" ] && macaddr_unsetbit $addr 6 > /sys${DEVPATH}/macaddress
 		[ "$PHYNBR" = "1" ] && macaddr_setbit $addr 6 > /sys${DEVPATH}/macaddress
 		;;
+	tplink,tl-xdr4288|\
+	tplink,tl-xdr6086|\
+	tplink,tl-xdr6088)
+		[ "$PHYNBR" = "0" ] && get_mac_label > /sys${DEVPATH}/macaddress
+		;;
 esac

target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh

@@ -67,15 +67,18 @@ platform_do_upgrade() {
 			;;
 		esac
 		;;
+	tplink,tl-xdr4288|\
+	tplink,tl-xdr6086|\
+	tplink,tl-xdr6088|\
+	xiaomi,redmi-router-ax6000-ubootmod)
+		CI_KERNPART="fit"
+		nand_do_upgrade "$1"
+		;;
 	xiaomi,redmi-router-ax6000-stock)
 		CI_KERN_UBIPART=ubi_kernel
 		CI_ROOT_UBIPART=ubi
 		nand_do_upgrade "$1"
 		;;
-	xiaomi,redmi-router-ax6000-ubootmod)
-		CI_KERNPART="fit"
-		nand_do_upgrade "$1"
-		;;
 	*)
 		nand_do_upgrade "$1"
 		;;

target/linux/mediatek/image/filogic.mk

@@ -141,6 +141,50 @@ define Device/mediatek_mt7986b-rfb
 endef
 TARGET_DEVICES += mediatek_mt7986b-rfb
 
+define Device/tplink_tl-xdr-common
+  DEVICE_VENDOR := TP-Link
+  DEVICE_DTS_DIR := ../dts
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  KERNEL_IN_UBI := 1
+  UBOOTENV_IN_UBI := 1
+  IMAGES := sysupgrade.itb
+  KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+  KERNEL := kernel-bin | gzip
+  KERNEL_INITRAMFS := kernel-bin | lzma | \
+        fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+  IMAGE/sysupgrade.itb := append-kernel | \
+        fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
+  DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
+  ARTIFACTS := preloader.bin bl31-uboot.fip
+  ARTIFACT/preloader.bin := bl2 spim-nand-ddr3
+endef
+
+define Device/tplink_tl-xdr4288
+  DEVICE_MODEL := TL-XDR4288
+  DEVICE_DTS := mt7986a-tplink-tl-xdr4288
+  ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr4288
+  $(call Device/tplink_tl-xdr-common)
+endef
+TARGET_DEVICES += tplink_tl-xdr4288
+
+define Device/tplink_tl-xdr6086
+  DEVICE_MODEL := TL-XDR6086
+  DEVICE_DTS := mt7986a-tplink-tl-xdr6086
+  ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr6086
+  $(call Device/tplink_tl-xdr-common)
+endef
+TARGET_DEVICES += tplink_tl-xdr6086
+
+define Device/tplink_tl-xdr6088
+  DEVICE_MODEL := TL-XDR6088
+  DEVICE_DTS := mt7986a-tplink-tl-xdr6088
+  ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr6088
+  $(call Device/tplink_tl-xdr-common)
+endef
+TARGET_DEVICES += tplink_tl-xdr6088
+
 define Device/xiaomi_redmi-router-ax6000-stock
   DEVICE_VENDOR := Xiaomi
   DEVICE_MODEL := Redmi Router AX6000 (stock layout)