x86: remove legacy script/makefile code for rdc devices

Signed-off-by: Felix Fietkau <[email protected]>

target/linux/x86/image/Makefile

@@ -181,30 +181,6 @@ define Image/BuildKernel
   endif
 endef
 
-define Image/Build/Profile/ar525w
-	cp $(KDIR)/bzImage $(KDIR)/bzImage.tmp
-	$(SCRIPT_DIR)/pad_image $(1) $(KDIR)/bzImage.tmp $(KDIR)/root.$(1) 32
-	$(STAGING_DIR_HOST)/bin/airlink -b 1 $(KDIR)/bzImage.tmp $(KDIR)/root.$(1) \
-		$(BIN_DIR)/$(IMG_PREFIX)-$(1)-ar525w.img
-	$(STAGING_DIR_HOST)/bin/airlink -e -b 1 $(KDIR)/bzImage.tmp $(KDIR)/root.$(1) \
-		$(BIN_DIR)/$(IMG_PREFIX)-$(1)-ar525w-web.img
-endef
-
-define Image/Build/Profile/sitecom
-	cp $(KDIR)/bzImage $(KDIR)/bzImage.tmp
-	#32k config data + 20 bytes header + 2 bytes checksum after kernel image
-	$(SCRIPT_DIR)/pad_image $(1) $(KDIR)/bzImage.tmp $(KDIR)/root.$(1) 32790
-	$(TOPDIR)/target/linux/rdc/image/mkimg_sitecom.pl $(KDIR)/bzImage.tmp > $(KDIR)/tmp.img
-	cat $(KDIR)/root.$(1) >> $(KDIR)/tmp.img
-	cp $(KDIR)/tmp.img $(BIN_DIR)/$(IMG_PREFIX)-$(1)-sitecom.img
-	rm $(KDIR)/tmp.img $(KDIR)/bzImage.tmp
-endef
-
-define Image/Build/Profile/bifferboard
-	$(TOPDIR)/target/linux/rdc/image/mkimg_bifferboard.py $(KDIR)/bzImage $(KDIR)/root.$(1) \
-		$(BIN_DIR)/$(IMG_PREFIX)-$(1)-bifferboard.img
-endef
-
 define Image/Prepare
 	$(call Image/Prepare/grub2)
 endef

target/linux/x86/image/mkimg_bifferboard.py

@@ -1,50 +0,0 @@
-#!/usr/bin/env python
-
-"""
-   Create firmware for 4/8MB Bifferboards, suitable for uploading using
-   either bb_upload8.py or bb_eth_upload8.py
-"""
-
-import struct, sys
-
-# Increase the kmax value if the script gives errors about the kernel being 
-# too large.  You need to set the Biffboot kmax value to the same value you
-# use here.
-kmax = 0x10
-
-# No need to change this for 4MB devices, it's only used to tell you if 
-# the firmware is too large!
-flash_size = 0x800000
-
-# This is always the same, for 1MB, 4MB and 8MB devices
-config_extent = 0x6000
-
-kernel_extent = kmax * 0x10000
-
-if __name__ == "__main__":
-
-  if len(sys.argv) != 4:
-    print  "usage: mkimg_bifferboard.py <kernel> <rootfs> <output file>"
-    sys.exit(-1)
-    
-  bzimage = sys.argv[1]
-  rootfs = sys.argv[2]
-  target = sys.argv[3]
-
-  # Kernel first
-  fw = file(bzimage).read()
-  if len(fw) > (kernel_extent - config_extent):
-    raise IOError("Kernel too large")
-
-  # Pad up to end of kernel partition
-  while len(fw) < (kernel_extent - config_extent):
-    fw += "\xff"
-
-  fw += file(rootfs).read()
-
-  # Check length of total
-  if len(fw) > (flash_size - 0x10000 - config_extent):
-    raise IOError("Rootfs too large")
-
-  file(target,"wb").write(fw)
-  print "Firmware written to '%s'" % target

target/linux/x86/image/mkimg_sitecom.pl

@@ -1,11 +0,0 @@
-#!/usr/bin/perl
-
-open (bzimg, @ARGV[0]);
-while (<bzimg>) { $i .= $_; }
-$i .= pack "v", -(unpack "%v*", $i); 
-print "CSYS";
-print pack("V", length($i));
-print pack("V", 0);
-print "WRRM";
-print pack("V", length($i));
-print $i;