target: replace remaining occurrences of ifconfig with ip

ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.

Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.

Signed-off-by: Adrian Schmutzler <[email protected]>

target/linux/apm821xx/base-files/lib/preinit/05_set_iface_mac_apm821xx

@@ -5,7 +5,7 @@ preinit_set_mac_address() {
 		meraki,mr24|\
 		meraki,mx60)
 			mac_lan=$(mtd_get_mac_binary_ubi board-config 0x66)
-			[ -n "$mac_lan" ] && ifconfig eth0 hw ether "$mac_lan"
+			[ -n "$mac_lan" ] && ip link set eth0 address "$mac_lan"
 			;;
 	esac
 }

target/linux/ath25/base-files/lib/preinit/15_preinit_iface_atheros

@@ -5,7 +5,7 @@ preinit_ip() {
 			if [ -e "/sys/bus/mdio_bus/drivers/Infineon ADM6996/0:00" -o \
 			     -e "/sys/bus/mdio_bus/drivers/Marvell 88E6060/0:10" ]; then
 				vconfig set_name_type DEV_PLUS_VID_NO_PAD
-				ifconfig eth0 up
+				ip link set eth0 up
 				vconfig add eth0 1
 				ifname=eth0.1
 			else
@@ -15,7 +15,8 @@ preinit_ip() {
 		}
 	fi
 	[ -n "$pi_ifname" ] && grep -q "$pi_ifname" /proc/net/dev && {
-		ifconfig $pi_ifname $pi_ip netmask $pi_netmask broadcast $pi_broadcast up
+		ip addr add $pi_ip/$pi_netmask broadcast $pi_broadcast dev $pi_ifname
+		ip link set $pi_ifname up
 	}
 }
 
@@ -26,8 +27,8 @@ preinit_ip_deconfig() {
 	if [ -e "/sys/bus/mdio_bus/drivers/Infineon ADM6996/0:00" -o \
 	     -e "/sys/bus/mdio_bus/drivers/Marvell 88E6060/0:10" ]; then
 		vconfig rem eth0.1 2>/dev/null
-		ifconfig $pi_ifname down
+		ip link set $pi_ifname down
 	elif [ -n "$pi_ifname" ]; then
-		ifconfig $pi_ifname 0.0.0.0
+		ip -4 addr flush dev $pi_ifname
 	fi
 }

target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface

@@ -1,5 +1,5 @@
 set_preinit_iface() {
-	ifconfig eth0 up
+	ip link set eth0 up
 	ifname=lan1
 }
 

target/linux/ramips/mt7621/base-files/lib/preinit/07_mt7621_bringup_dsa_master

@@ -14,7 +14,7 @@ mt7621_bringup_dsa_master() {
         ;;
     esac
 
-    ifconfig $masterif up
+    ip link set $masterif up
 }
 
 boot_hook_add preinit_main mt7621_bringup_dsa_master

target/linux/sunxi/base-files/lib/preinit/03_b53_hack.sh

@@ -4,7 +4,7 @@ do_b53_hack() {
 	# hack: enable switch on Lamobo R1 and reset counters
 	case $(board_name) in
 	lamobo,lamobo-r1)
-		ifconfig eth0 up
+		ip link set eth0 up
 		sleep 1
 		swconfig dev switch0 set reset 1
 		swconfig dev switch0 set reset_mib 1