|
|
@@ -0,0 +1,171 @@
|
|
|
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
+
|
|
|
+#include "rtl838x.dtsi"
|
|
|
+#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi"
|
|
|
+
|
|
|
+#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
+
|
|
|
+/ {
|
|
|
+ compatible = "panasonic,m16eg-pn28160k", "realtek,rtl8382-soc";
|
|
|
+ model = "Panasonic Switch-M16eG PN28160K";
|
|
|
+
|
|
|
+ aliases {
|
|
|
+ led-boot = &led_status_eco_green;
|
|
|
+ led-failsafe = &led_status_eco_amber;
|
|
|
+ led-running = &led_status_eco_green;
|
|
|
+ led-upgrade = &led_status_eco_green;
|
|
|
+ };
|
|
|
+
|
|
|
+ /*
|
|
|
+ * sfp0/1 are "combo" port with each TP port (23/24), and they are
|
|
|
+ * connected to the RTL8218FB. Currently, there is no support for
|
|
|
+ * the chip and only TP ports work by the RTL8218D support.
|
|
|
+ */
|
|
|
+ sfp0: sfp-p23 {
|
|
|
+ compatible = "sff,sfp";
|
|
|
+ i2c-bus = <&i2c0>;
|
|
|
+ tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
|
|
|
+ tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
|
|
|
+ mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
|
|
|
+ los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+
|
|
|
+ sfp1: sfp-p24 {
|
|
|
+ compatible = "sff,sfp";
|
|
|
+ i2c-bus = <&i2c1>;
|
|
|
+ tx-fault-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
|
|
|
+ tx-disable-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
|
|
|
+ mod-def0-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
|
|
+ los-gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&leds {
|
|
|
+ led_status_eco_amber: led-5 {
|
|
|
+ label = "amber:status_eco";
|
|
|
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
|
|
+ color = <LED_COLOR_ID_AMBER>;
|
|
|
+ function = LED_FUNCTION_STATUS;
|
|
|
+ function-enumerator = <1>;
|
|
|
+ };
|
|
|
+
|
|
|
+ led_status_eco_green: led-6 {
|
|
|
+ label = "green:status_eco";
|
|
|
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
|
|
|
+ color = <LED_COLOR_ID_GREEN>;
|
|
|
+ function = LED_FUNCTION_STATUS;
|
|
|
+ function-enumerator = <2>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&i2c_gpio_0 {
|
|
|
+ scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
+ sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
+};
|
|
|
+
|
|
|
+&i2c_gpio_1 {
|
|
|
+ scl-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
+ sda-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
+};
|
|
|
+
|
|
|
+&gpio2 {
|
|
|
+ interrupt-controller;
|
|
|
+ #interrupt-cells = <2>;
|
|
|
+ interrupt-parent = <&gpio0>;
|
|
|
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
|
|
|
+
|
|
|
+ /*
|
|
|
+ * GPIO12 (IO1_4): RTL8218FB
|
|
|
+ *
|
|
|
+ * This GPIO pin should be specified as "reset-gpio" in mdio node, but
|
|
|
+ * RTL8218FB phy won't be configured on RTL8218D support in the current
|
|
|
+ * phy driver. So, ethernet ports on the phy will be broken after hard-
|
|
|
+ * resetting.
|
|
|
+ * (RTL8218FB phy will be detected as RTL8218D by the phy driver)
|
|
|
+ * At the moment, configure this GPIO pin as gpio-hog to avoid breaking
|
|
|
+ * by resetting.
|
|
|
+ */
|
|
|
+ ext_switch_reset {
|
|
|
+ gpio-hog;
|
|
|
+ gpios = <12 GPIO_ACTIVE_HIGH>;
|
|
|
+ output-high;
|
|
|
+ line-name = "ext-switch-reset";
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&i2c_switch {
|
|
|
+ i2c0: i2c@0 {
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+ reg = <0>;
|
|
|
+ };
|
|
|
+
|
|
|
+ i2c1: i2c@1 {
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+ reg = <1>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+ðernet0 {
|
|
|
+ mdio-bus {
|
|
|
+ compatible = "realtek,rtl838x-mdio";
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+
|
|
|
+ INTERNAL_PHY(8)
|
|
|
+ INTERNAL_PHY(9)
|
|
|
+ INTERNAL_PHY(10)
|
|
|
+ INTERNAL_PHY(11)
|
|
|
+ INTERNAL_PHY(12)
|
|
|
+ INTERNAL_PHY(13)
|
|
|
+ INTERNAL_PHY(14)
|
|
|
+ INTERNAL_PHY(15)
|
|
|
+
|
|
|
+ /* RTL8218FB */
|
|
|
+ EXTERNAL_PHY(16)
|
|
|
+ EXTERNAL_PHY(17)
|
|
|
+ EXTERNAL_PHY(18)
|
|
|
+ EXTERNAL_PHY(19)
|
|
|
+ EXTERNAL_PHY(20)
|
|
|
+ EXTERNAL_PHY(21)
|
|
|
+ EXTERNAL_PHY(22)
|
|
|
+ EXTERNAL_PHY(23)
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&switch0 {
|
|
|
+ ports {
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+
|
|
|
+ SWITCH_PORT(8, 1, internal)
|
|
|
+ SWITCH_PORT(9, 2, internal)
|
|
|
+ SWITCH_PORT(10, 3, internal)
|
|
|
+ SWITCH_PORT(11, 4, internal)
|
|
|
+ SWITCH_PORT(12, 5, internal)
|
|
|
+ SWITCH_PORT(13, 6, internal)
|
|
|
+ SWITCH_PORT(14, 7, internal)
|
|
|
+ SWITCH_PORT(15, 8, internal)
|
|
|
+
|
|
|
+ SWITCH_PORT(16, 9, qsgmii)
|
|
|
+ SWITCH_PORT(17, 10, qsgmii)
|
|
|
+ SWITCH_PORT(18, 11, qsgmii)
|
|
|
+ SWITCH_PORT(19, 12, qsgmii)
|
|
|
+ SWITCH_PORT(20, 13, qsgmii)
|
|
|
+ SWITCH_PORT(21, 14, qsgmii)
|
|
|
+ SWITCH_PORT(22, 15, qsgmii)
|
|
|
+ SWITCH_PORT(23, 16, qsgmii)
|
|
|
+
|
|
|
+ port@28 {
|
|
|
+ ethernet = <ðernet0>;
|
|
|
+ reg = <28>;
|
|
|
+ phy-mode = "internal";
|
|
|
+
|
|
|
+ fixed-link {
|
|
|
+ speed = <1000>;
|
|
|
+ full-duplex;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+};
|
INAGAKI Hiroshi