mediatek: use NVMEM framework on all Adtran devices

Use NVMEM framework to assign MAC addresses and WiFi EEPROM data on
all Adtran SmartRG devices.

Signed-off-by: Daniel Golle <[email protected]>

target/linux/mediatek/dts/mt7986a-smartrg-bonanza-peak.dtsi

@@ -14,8 +14,7 @@
 / {
 	aliases {
 		serial0 = &uart0;
-		ethernet0 = &gmac0;
-		ethernet1 = &gmac1;
+		label-mac-device = &gmac1;
 		led-boot = &led_status_green;
 		led-failsafe = &led_status_red;
 		led-running = &led_status_white;
@@ -188,16 +187,17 @@
 	gmac0: mac@0 {
 		compatible = "mediatek,eth-mac";
 		reg = <0>;
-
+		nvmem-cells = <&macaddr 1>;
+		nvmem-cell-names = "mac-address";
 		phy-mode = "2500base-x";
 	};
 
 	gmac1: mac@1 {
-		label = "wan";
-
 		compatible = "mediatek,eth-mac";
 		reg = <1>;
-
+		label = "wan";
+		nvmem-cells = <&macaddr 0>;
+		nvmem-cell-names = "mac-address";
 		phy-mode = "2500base-x";
 	};
 
@@ -254,6 +254,47 @@
 	no-sd;
 	no-sdio;
 	status = "okay";
+
+	card@0 {
+		compatible = "mmc-card";
+		reg = <0>;
+
+		block {
+			compatible = "block-device";
+
+			partitions {
+				block-partition-factory {
+					partname = "factory";
+
+					nvmem-layout {
+						compatible = "fixed-layout";
+						#address-cells = <1>;
+						#size-cells = <1>;
+
+						eeprom_factory_0: eeprom@0 {
+							reg = <0x0 0x1000>;
+						};
+
+						eeprom_factory_a0000: eeprom@a0000 {
+							reg = <0xa0000 0x1000>;
+						};
+					};
+				};
+
+				block-partition-mfginfo {
+					partname = "mfginfo";
+
+					nvmem-layout {
+						compatible = "adtran,mfginfo";
+
+						macaddr: mfg-mac {
+							#nvmem-cell-cells = <1>;
+						};
+					};
+				};
+			};
+		};
+	};
 };
 
 &pcie {
@@ -266,6 +307,9 @@
 
 		radio0: mt7915@0,0 {
 			reg = <0x0000 0 0 0 0>;
+
+			nvmem-cells = <&eeprom_factory_a0000>, <&macaddr 4>;
+			nvmem-cell-names = "eeprom", "mac-address";
 		};
 	};
 };
@@ -275,9 +319,28 @@
 };
 
 &wifi {
-	status = "okay";
+	nvmem-cells = <&eeprom_factory_0>;
+	nvmem-cell-names = "eeprom";
 	pinctrl-names = "default";
 	pinctrl-0 = <&wf_2g_5g_pins>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	band@0 {
+		/* 2.4 GHz */
+		reg = <0>;
+		nvmem-cells = <&macaddr 2>;
+		nvmem-cell-names = "mac-address";
+	};
+
+	band@1 {
+		/* lower 5 GHz */
+		reg = <1>;
+		nvmem-cells = <&macaddr 3>;
+		nvmem-cell-names = "mac-address";
+	};
 };
 
 &pio {

target/linux/mediatek/dts/mt7988a-smartrg-mt-stuart.dtsi

@@ -15,8 +15,7 @@
 / {
 	aliases {
 		serial0 = &uart0;
-		ethernet0 = &gmac0;
-		ethernet1 = &gmac1;
+		label-mac-device = &gmac1;
 		led-boot = &led_sys_green;
 		led-failsafe = &led_sys_blue;
 		led-running = &led_sys_white;
@@ -250,21 +249,30 @@
 };
 
 &gmac0 {
+	nvmem-cells = <&macaddr 1>;
+	nvmem-cell-names = "mac-address";
+
 	status = "okay";
 };
 
 &gmac1 {
+	nvmem-cells = <&macaddr 0>;
+	nvmem-cell-names = "mac-address";
 	label = "wan";
-	status = "okay";
 	phy-mode = "usxgmii";
+
+	status = "okay";
 };
 
 &gmac2 {
+	nvmem-cells = <&macaddr 1>;
+	nvmem-cell-names = "mac-address";
 	label = "lan1";
-	status = "okay";
 	phy-mode = "usxgmii";
 	phy-connection-type = "usxgmii";
 	phy = <&phy8>;
+
+	status = "okay";
 };
 
 &gsw_phy0 {
@@ -513,6 +521,18 @@
 						};
 					};
 				};
+
+				block-partition-mfginfo {
+					partname = "mfginfo";
+
+					nvmem-layout {
+						compatible = "adtran,mfginfo";
+
+						macaddr: mfg-mac {
+							#nvmem-cell-cells = <1>;
+						};
+					};
+				};
 			};
 		};
 	};
@@ -532,6 +552,27 @@
 			nvmem-cells = <&eeprom_factory_0>;
 			nvmem-cell-names = "eeprom";
 			ieee80211-freq-limit = <2400000 2500000>, <5170000 5835000>, <5945000 7125000>;
+
+			band@0 {
+				/* 2.4 GHz */
+				reg = <0>;
+				nvmem-cells = <&macaddr 4>;
+				nvmem-cell-names = "mac-address";
+			};
+
+			band@1 {
+				/* 5 GHz */
+				reg = <1>;
+				nvmem-cells = <&macaddr 10>;
+				nvmem-cell-names = "mac-address";
+			};
+
+			band@2 {
+				/* 6 GHz */
+				reg = <2>;
+				nvmem-cells = <&macaddr 6>;
+				nvmem-cell-names = "mac-address";
+			};
 		};
 	};
 };

target/linux/mediatek/dts/mt7988d-smartrg-SDG-8733A.dts

@@ -62,6 +62,8 @@
 
 &gmac1 {
 	label = "lan";
+	nvmem-cells = <&macaddr 1>;
+	nvmem-cell-names = "mac-address";
 	phy-mode = "internal";
 	phy-connection-type = "internal";
 	phy = <&int_2p5g_phy>;
@@ -69,6 +71,8 @@
 
 &gmac2 {
 	label = "wan";
+	nvmem-cells = <&macaddr 0>;
+	nvmem-cell-names = "mac-address";
 	phy-mode = "usxgmii";
 	phy-connection-type = "usxgmii";
 	phy = <&phy8>;

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -162,16 +162,6 @@ mediatek_setup_macs()
 		wan_mac=$label_mac
 		lan_mac=$(macaddr_add "$label_mac" 1)
 		;;
-	smartrg,sdg-8612|\
-	smartrg,sdg-8614|\
-	smartrg,sdg-8622|\
-	smartrg,sdg-8632|\
-	smartrg,sdg-8733|\
-	smartrg,sdg-8734)
-		label_mac=$(mmc_get_mac_ascii mfginfo MFG_MAC)
-		wan_mac=$label_mac
-		lan_mac=$(macaddr_add "$label_mac" 1)
-		;;
 	xiaomi,mi-router-ax3000t|\
 	xiaomi,mi-router-ax3000t-ubootmod|\
 	xiaomi,mi-router-wr30u-stock|\

target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata

@@ -7,21 +7,6 @@
 board=$(board_name)
 
 case "$FIRMWARE" in
-"mediatek/mt7915_eeprom.bin")
-	case "$board" in
-	smartrg,sdg-8622)
-		caldata_extract_mmc "factory" 0xa0000 0x1000
-		;;
-	esac
-	;;
-"mediatek/mt7916_eeprom.bin")
-	case "$board" in
-	acer,predator-w6|\
-	smartrg,sdg-8632)
-		caldata_extract_mmc "factory" 0xa0000 0x1000
-		;;
-	esac
-	;;
 "mediatek/mt7981_eeprom_mt7976_dbdc.bin")
 	case "$board" in
 	ubnt,unifi-6-plus)
@@ -36,12 +21,6 @@ case "$FIRMWARE" in
 		ln -sf /tmp/tp_data/MT7986_EEPROM.bin \
 			/lib/firmware/$FIRMWARE
 		;;
-	smartrg,sdg-8612|\
-	smartrg,sdg-8614|\
-	smartrg,sdg-8622|\
-	smartrg,sdg-8632)
-		caldata_extract_mmc "factory" 0x0 0x1000
-		;;
 	esac
 	;;
 "mediatek/mt7986_eeprom_mt7976.bin")

target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac

@@ -139,23 +139,6 @@ case "$board" in
 		[ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
 		[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
 		;;
-	smartrg,sdg-8612|\
-	smartrg,sdg-8614|\
-	smartrg,sdg-8622|\
-	smartrg,sdg-8632)
-		addr=$(mmc_get_mac_ascii mfginfo MFG_MAC)
-		[ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
-		[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
-		[ "$PHYNBR" = "2" ] && macaddr_add $addr 4 > /sys${DEVPATH}/macaddress
-		;;
-	smartrg,sdg-8733|\
-	smartrg,sdg-8733a|\
-	smartrg,sdg-8734)
-		addr=$(mmc_get_mac_ascii mfginfo MFG_MAC)
-		[ "$PHYNBR" = "0" ] && macaddr_add $addr 4 > /sys${DEVPATH}/macaddress
-		[ "$PHYNBR" = "1" ] && macaddr_add $addr a > /sys${DEVPATH}/macaddress
-		[ "$PHYNBR" = "2" ] && macaddr_add $addr 6 > /sys${DEVPATH}/macaddress
-		;;
 	tplink,tl-xdr4288|\
 	tplink,tl-xdr6086|\
 	tplink,tl-xdr6088)

target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh

@@ -22,26 +22,6 @@ preinit_set_mac_address() {
 		addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
 		ip link set dev eth1 address "$(macaddr_add $addr 1)"
 		;;
-	smartrg,sdg-8612|\
-	smartrg,sdg-8614|\
-	smartrg,sdg-8733|\
-	smartrg,sdg-8734)
-		addr=$(mmc_get_mac_ascii mfginfo MFG_MAC)
-		lan_addr=$(macaddr_add $addr 1)
-		ip link set dev wan address "$addr"
-		ip link set dev eth0 address "$lan_addr"
-		ip link set dev lan1 address "$lan_addr"
-		ip link set dev lan2 address "$lan_addr"
-		ip link set dev lan3 address "$lan_addr"
-		ip link set dev lan4 address "$lan_addr"
-		;;
-	smartrg,sdg-8622|\
-	smartrg,sdg-8632|\
-	smartrg,sdg-8733a)
-		addr=$(mmc_get_mac_ascii mfginfo MFG_MAC)
-		ip link set dev wan address "$addr"
-		ip link set dev lan address "$(macaddr_add $addr 1)"
-		;;
 	*)
 		;;
 	esac