mediatek: add support for Zbtlink ZBT-Z8103AX

Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.

Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi

Buttons:
Reset-Mesh

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Signed-off-by: Ian Oderon <[email protected]>

package/boot/uboot-envtools/files/mediatek_filogic

@@ -56,7 +56,8 @@ cmcc,rax3000m)
 	;;
 cetron,ct3003|\
 netgear,wax220|\
-zbtlink,zbt-z8102ax)
+zbtlink,zbt-z8102ax|\
+zbtlink,zbt-z8103ax)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
 	;;
 h3c,magic-nx30-pro|\

target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts

@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT 
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+	model = "Zbtlink ZBT-Z8103AX";
+	compatible = "zbtlink,zbt-z8103ax", "mediatek,mt7981";
+
+	aliases {
+		serial0 = &uart0;
+		led-boot = &led_status_green;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_green;
+		led-upgrade = &led_status_green;
+		label-mac-device = &gmac0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 loglevel=8";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x10000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-mesh {
+			label = "mesh";
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+			gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wan {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led-status-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_status_green: led-status-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led_status_red: led-status-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wlan2g {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WLAN;
+			gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+			function-enumerator = <0>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		led-wlan5g {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WLAN;
+			gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+			function-enumerator = <1>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		/* LAN */
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		nvmem-cell-names = "mac-address";
+		nvmem-cells = <&macaddr_factory_4 2>;
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		/* WAN */
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "gmii";
+		phy-handle = <&int_gbe_phy>;
+
+		nvmem-cell-names = "mac-address";
+		nvmem-cells = <&macaddr_factory_4 3>;
+	};
+};
+
+&mdio_bus {
+	switch: switch@1f {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_flash_pins>;
+	status = "okay";
+
+	spi_nand@0 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+
+		spi-max-frequency = <52000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bl2";
+				reg = <0x0000000 0x0100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "u-boot-env";
+				reg = <0x100000 0x80000>;
+			};
+
+			partition@180000 {
+				label = "Factory";
+				reg = <0x180000 0x200000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					eeprom_factory: eeprom@0 {
+						reg = <0x0 0x1000>;
+					};
+
+					macaddr_factory_4: macaddr@4 {
+						compatible = "mac-base";
+						reg = <0x4 0x6>;
+						#nvmem-cell-cells = <1>;
+					};
+				};
+			};
+
+			partition@380000 {
+				label = "FIP";
+				reg = <0x380000 0x200000>;
+				read-only;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x580000 0x4000000>;
+			};
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	spi0_flash_pins: spi0-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+		};
+
+		conf-pd {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	nvmem-cells = <&eeprom_factory>;
+	nvmem-cell-names = "eeprom";
+};

target/linux/mediatek/filogic/base-files/etc/board.d/01_leds

@@ -35,6 +35,9 @@ xiaomi,redmi-router-ax6000-stock|\
 xiaomi,redmi-router-ax6000-ubootmod)
 	ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan"
 	;;
+zbtlink,zbt-z8103ax)
+	ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
+	;;
 zyxel_ex5601-t0-stock|\
 zyxel,ex5601-t0-ubootmod)
 	ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link tx rx"

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -33,7 +33,8 @@ mediatek_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
 		;;
 	cmcc,rax3000m|\
-	h3c,magic-nx30-pro)
+	h3c,magic-nx30-pro|\
+	zbtlink,zbt-z8103ax)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1
 		;;
 	glinet,gl-mt2500|\

target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac

@@ -105,6 +105,7 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
 		;;
 	zbtlink,zbt-z8102ax|\
+	zbtlink,zbt-z8103ax|\
 	zyxel,ex5601-t0|\
 	zyxel,ex5601-t0-ubootmod)
 		addr=$(mtd_get_mac_binary "Factory" 0x4)

target/linux/mediatek/image/filogic.mk

@@ -831,6 +831,23 @@ define Device/zbtlink_zbt-z8102ax
 endef
 TARGET_DEVICES += zbtlink_zbt-z8102ax
 
+define Device/zbtlink_zbt-z8103ax
+  DEVICE_VENDOR := Zbtlink
+  DEVICE_MODEL := ZBT-Z8103AX
+  DEVICE_DTS := mt7981b-zbtlink-zbt-z8103ax
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+  KERNEL_IN_UBI := 1
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 65536k
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += zbtlink_zbt-z8103ax
+
 define Device/zyxel_ex5601-t0-stock
   DEVICE_VENDOR := Zyxel
   DEVICE_MODEL := EX5601-T0