ath79: Move TPLink WPA8630Pv2 to ath79-tiny target

These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.

Note for users sysupgrading from the previous ath79-generic snapshot
images:

The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.

To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".

If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:

* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot

Signed-off-by: Joe Mullally <[email protected]>
Tested-by: Robert Högberg <[email protected]>

target/linux/ath79/generic/base-files/etc/board.d/01_leds

@@ -401,10 +401,7 @@ tplink,tl-mr6400-v1)
 	ucidef_set_led_netdev "wan" "WAN" "white:wan" "eth1"
 	ucidef_set_led_netdev "4g" "4G" "white:4g" "usb0"
 	;;
-tplink,tl-wpa8630-v1|\
-tplink,tl-wpa8630p-v2-int|\
-tplink,tl-wpa8630p-v2.0-eu|\
-tplink,tl-wpa8630p-v2.1-eu)
+tplink,tl-wpa8630-v1)
 	ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3c"
 	;;
 tplink,tl-wr841hp-v2|\

target/linux/ath79/generic/base-files/etc/board.d/02_network

@@ -440,10 +440,7 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "1:lan:1" "2:lan:3" "3:lan:2"
 		;;
-	tplink,tl-wpa8630-v1|\
-	tplink,tl-wpa8630p-v2-int|\
-	tplink,tl-wpa8630p-v2.0-eu|\
-	tplink,tl-wpa8630p-v2.1-eu)
+	tplink,tl-wpa8630-v1)
 		# port 5 (internal) is the power-line port
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4"

target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -249,10 +249,7 @@ case "$FIRMWARE" in
 		;;
 	tplink,eap225-outdoor-v1|\
 	tplink,eap225-v3|\
-	tplink,eap225-wall-v2|\
-	tplink,tl-wpa8630p-v2-int|\
-	tplink,tl-wpa8630p-v2.0-eu|\
-	tplink,tl-wpa8630p-v2.1-eu)
+	tplink,eap225-wall-v2)
 		caldata_extract "art" 0x5000 0x2f20
 		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) 1)
 		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \

target/linux/ath79/image/generic-tp-link.mk

@@ -640,36 +640,6 @@ define Device/tplink_tl-wpa8630-v1
 endef
 TARGET_DEVICES += tplink_tl-wpa8630-v1
 
-define Device/tplink_tl-wpa8630p-v2
-  $(Device/tplink-safeloader)
-  SOC := qca9563
-  DEVICE_MODEL := TL-WPA8630P
-  IMAGE_SIZE := 6016k
-  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
-endef
-
-define Device/tplink_tl-wpa8630p-v2-int
-  $(Device/tplink_tl-wpa8630p-v2)
-  DEVICE_VARIANT := v2 (Int.)
-  TPLINK_BOARD_ID := TL-WPA8630P-V2-INT
-endef
-TARGET_DEVICES += tplink_tl-wpa8630p-v2-int
-
-define Device/tplink_tl-wpa8630p-v2.0-eu
-  $(Device/tplink_tl-wpa8630p-v2)
-  DEVICE_VARIANT := v2.0 (EU)
-  TPLINK_BOARD_ID := TL-WPA8630P-V2.0-EU
-  SUPPORTED_DEVICES += tplink,tl-wpa8630p-v2-eu
-endef
-TARGET_DEVICES += tplink_tl-wpa8630p-v2.0-eu
-
-define Device/tplink_tl-wpa8630p-v2.1-eu
-  $(Device/tplink_tl-wpa8630p-v2)
-  DEVICE_VARIANT := v2.1 (EU)
-  TPLINK_BOARD_ID := TL-WPA8630P-V2.1-EU
-endef
-TARGET_DEVICES += tplink_tl-wpa8630p-v2.1-eu
-
 define Device/tplink_tl-wr1043nd-v1
   $(Device/tplink-8m)
   SOC := ar9132

target/linux/ath79/image/tiny-tp-link.mk

@@ -223,6 +223,41 @@ define Device/tplink_tl-wa901nd-v5
 endef
 TARGET_DEVICES += tplink_tl-wa901nd-v5
 
+define Device/tplink_tl-wpa8630p-v2
+  $(Device/tplink-safeloader)
+  SOC := qca9563
+  DEVICE_MODEL := TL-WPA8630P
+  IMAGE_SIZE := 6016k
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+  DEVICE_COMPAT_VERSION := 2.0
+  DEVICE_COMPAT_MESSAGE := The flash erase blocksize has changed to 4k from the 64k in previous versions, \
+    so the JFFS2 settings partition MUST be reformatted to avoid data corruption. \
+    Backup your settings before upgrading, then during sysupgrade, \
+    de-select "Keep settings" and select "Force" to continue (equivilant to "sysupgrade -n -F").
+endef
+
+define Device/tplink_tl-wpa8630p-v2-int
+  $(Device/tplink_tl-wpa8630p-v2)
+  DEVICE_VARIANT := v2 (Int.)
+  TPLINK_BOARD_ID := TL-WPA8630P-V2-INT
+endef
+TARGET_DEVICES += tplink_tl-wpa8630p-v2-int
+
+define Device/tplink_tl-wpa8630p-v2.0-eu
+  $(Device/tplink_tl-wpa8630p-v2)
+  DEVICE_VARIANT := v2.0 (EU)
+  TPLINK_BOARD_ID := TL-WPA8630P-V2.0-EU
+  SUPPORTED_DEVICES += tplink,tl-wpa8630p-v2-eu
+endef
+TARGET_DEVICES += tplink_tl-wpa8630p-v2.0-eu
+
+define Device/tplink_tl-wpa8630p-v2.1-eu
+  $(Device/tplink_tl-wpa8630p-v2)
+  DEVICE_VARIANT := v2.1 (EU)
+  TPLINK_BOARD_ID := TL-WPA8630P-V2.1-EU
+endef
+TARGET_DEVICES += tplink_tl-wpa8630p-v2.1-eu
+
 define Device/tplink_tl-wr703n
   $(Device/tplink-4mlzma)
   SOC := ar9331

target/linux/ath79/tiny/base-files/etc/board.d/01_leds

@@ -93,6 +93,11 @@ tplink,tl-wa850re-v2)
 	ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "blue:signal4" "wlan0" "60" "100"
 	ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "blue:signal5" "wlan0" "80" "100"
 	;;
+tplink,tl-wpa8630p-v2-int|\
+tplink,tl-wpa8630p-v2.0-eu|\
+tplink,tl-wpa8630p-v2.1-eu)
+	ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3c"
+	;;
 tplink,tl-wr940n-v3|\
 tplink,tl-wr940n-v4|\
 tplink,tl-wr941nd-v6)

target/linux/ath79/tiny/base-files/etc/board.d/02_network

@@ -82,6 +82,13 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
 		;;
+	tplink,tl-wpa8630p-v2-int|\
+	tplink,tl-wpa8630p-v2.0-eu|\
+	tplink,tl-wpa8630p-v2.1-eu)
+		# port 5 (internal) is the power-line port
+		ucidef_add_switch "switch0" \
+			"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "5:lan:4"
+		;;
 	tplink,tl-wr941-v2)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
 		;;

target/linux/ath79/tiny/base-files/etc/board.d/05_compat-version

@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2020 OpenWrt.org
+#
+
+. /lib/functions.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+	tplink,tl-wpa8630p-v2-int|\
+	tplink,tl-wpa8630p-v2.0-eu|\
+	tplink,tl-wpa8630p-v2.1-eu)
+		ucidef_set_compat_version "2.0"
+		;;
+esac
+
+board_config_flush
+
+exit 0

target/linux/ath79/tiny/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -0,0 +1,25 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions/caldata.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath10k/pre-cal-pci-0000:00:00.0.bin")
+	case $board in
+	tplink,tl-wpa8630p-v2-int|\
+	tplink,tl-wpa8630p-v2.0-eu|\
+	tplink,tl-wpa8630p-v2.1-eu)
+		caldata_extract "art" 0x5000 0x2f20
+		ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) 1)
+		ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+			/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+		;;
+	esac
+	;;
+*)
+	exit 1
+	;;
+esac