|
|
@@ -1,63 +0,0 @@
|
|
|
-diff -urN linux-2.6.16.7/arch/mips/au1000/mtx-1/board_setup.c linux-2.6.16.7.new/arch/mips/au1000/mtx-1/board_setup.c
|
|
|
---- linux-2.6.16.7/arch/mips/au1000/mtx-1/board_setup.c 2006-04-23 14:39:21.000000000 +0200
|
|
|
-+++ linux-2.6.16.7.new/arch/mips/au1000/mtx-1/board_setup.c 2006-04-23 14:39:03.000000000 +0200
|
|
|
-@@ -44,6 +44,9 @@
|
|
|
- #include <asm/pgtable.h>
|
|
|
- #include <asm/mach-au1x00/au1000.h>
|
|
|
-
|
|
|
-+extern int (*board_pci_idsel)(unsigned int devsel, int assert);
|
|
|
-+int mtx1_pci_idsel(unsigned int devsel, int assert);
|
|
|
-+
|
|
|
- void board_reset (void)
|
|
|
- {
|
|
|
- /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
|
|
|
-@@ -77,11 +80,37 @@
|
|
|
- au_writel( 0xFFFFFFFF, SYS_TRIOUTCLR );
|
|
|
- au_writel( 0x00000001, SYS_OUTPUTCLR ); // set M66EN (PCI 66MHz) to OFF
|
|
|
- au_writel( 0x00000008, SYS_OUTPUTSET ); // set PCI CLKRUN# to OFF
|
|
|
-+ au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
|
|
|
- au_writel( 0x00000020, SYS_OUTPUTCLR ); // set eth PHY TX_ER to OFF
|
|
|
-
|
|
|
- // enable LED and set it to green
|
|
|
- au_writel( au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR );
|
|
|
- au_writel( 0x18000800, GPIO2_OUTPUT );
|
|
|
-
|
|
|
-+ board_pci_idsel = mtx1_pci_idsel;
|
|
|
-+
|
|
|
- printk("4G Systems MTX-1 Board\n");
|
|
|
- }
|
|
|
-+
|
|
|
-+int
|
|
|
-+mtx1_pci_idsel(unsigned int devsel, int assert)
|
|
|
-+{
|
|
|
-+#define MTX_IDSEL_ONLY_0_AND_3 0
|
|
|
-+#if MTX_IDSEL_ONLY_0_AND_3
|
|
|
-+ if (devsel != 0 && devsel != 3) {
|
|
|
-+ printk("*** not 0 or 3\n");
|
|
|
-+ return 0;
|
|
|
-+ }
|
|
|
-+#endif
|
|
|
-+
|
|
|
-+ if (assert && devsel != 0) {
|
|
|
-+ // supress signal to cardbus
|
|
|
-+ au_writel( 0x00000002, SYS_OUTPUTCLR ); // set EXT_IO3 OFF
|
|
|
-+ }
|
|
|
-+ else {
|
|
|
-+ au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
|
|
|
-+ }
|
|
|
-+ au_sync_udelay(1);
|
|
|
-+ return 1;
|
|
|
-+}
|
|
|
-+
|
|
|
-diff -urN linux-2.6.16.7/arch/mips/au1000/mtx-1/irqmap.c linux-2.6.16.7.new/arch/mips/au1000/mtx-1/irqmap.c
|
|
|
---- linux-2.6.16.7/arch/mips/au1000/mtx-1/irqmap.c 2006-04-23 14:40:54.000000000 +0200
|
|
|
-+++ linux-2.6.16.7.new/arch/mips/au1000/mtx-1/irqmap.c 2006-04-23 14:40:12.000000000 +0200
|
|
|
-@@ -48,7 +48,7 @@
|
|
|
- #include <asm/mach-au1x00/au1000.h>
|
|
|
-
|
|
|
- char irq_tab_alchemy[][5] __initdata = {
|
|
|
-- [0] = { -1, INTA, INTB, INTX, INTX}, /* IDSEL 00 - AdapterA-Slot0 (top) */
|
|
|
-+ [0] = { -1, INTA, INTA, INTX, INTX}, /* IDSEL 00 - AdapterA-Slot0 (top) */
|
|
|
- [1] = { -1, INTB, INTA, INTX, INTX}, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
|
|
|
- [2] = { -1, INTC, INTD, INTX, INTX}, /* IDSEL 02 - AdapterB-Slot0 (top) */
|
|
|
- [3] = { -1, INTD, INTC, INTX, INTX}, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
|
Florian Fainelli