remove custom phy layer patches from older kernels where they are not needed

SVN-Revision: 14978

target/linux/generic-2.6/patches-2.6.23/610-phy_detect.patch

@@ -1,26 +0,0 @@
---- a/drivers/net/phy/mdio_bus.c
-+++ b/drivers/net/phy/mdio_bus.c
-@@ -131,6 +131,9 @@ static int mdio_bus_match(struct device 
- 	struct phy_device *phydev = to_phy_device(dev);
- 	struct phy_driver *phydrv = to_phy_driver(drv);
- 
-+	if (phydrv->detect)
-+		return (phydrv->detect(phydev->bus, phydev->addr));
-+
- 	return ((phydrv->phy_id & phydrv->phy_id_mask) ==
- 		(phydev->phy_id & phydrv->phy_id_mask));
- }
---- a/include/linux/phy.h
-+++ b/include/linux/phy.h
-@@ -319,6 +319,11 @@ struct phy_driver {
- 	u32 features;
- 	u32 flags;
- 
-+	/* Called during discovery to test if the
-+	 * device can attach to the bus, even if
-+	 * phy id and mask do not match */
-+	bool (*detect)(struct mii_bus *bus, int addr);
-+
- 	/* Called to initialize the PHY,
- 	 * including after a reset */
- 	int (*config_init)(struct phy_device *phydev);

target/linux/generic-2.6/patches-2.6.23/620-phy_adm6996.patch

@@ -1,22 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -60,6 +60,11 @@ config ICPLUS_PHY
- 	---help---
- 	  Currently supports the IP175C PHY.
- 
-+config ADM6996_PHY
-+	tristate "Driver for ADM6996 switches"
-+	---help---
-+	  Currently supports the ADM6996F switch
-+
- config FIXED_PHY
- 	tristate "Drivers for PHY emulation on fixed speed/link"
- 	---help---
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -12,4 +12,5 @@ obj-$(CONFIG_SMSC_PHY)		+= smsc.o
- obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
- obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
- obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
-+obj-$(CONFIG_ADM6996_PHY)	+= adm6996.o
- obj-$(CONFIG_FIXED_PHY)		+= fixed.o

target/linux/generic-2.6/patches-2.6.23/630-phy_packets.patch

@@ -1,60 +0,0 @@
---- a/drivers/net/phy/phy_device.c
-+++ b/drivers/net/phy/phy_device.c
-@@ -44,6 +44,18 @@ static struct phy_driver genphy_driver;
- extern int mdio_bus_init(void);
- extern void mdio_bus_exit(void);
- 
-+static int generic_receive_skb(struct sk_buff *skb)
-+{
-+	skb->protocol = eth_type_trans(skb, skb->dev);
-+	return netif_receive_skb(skb);
-+}
-+
-+static int generic_rx(struct sk_buff *skb)
-+{
-+	skb->protocol = eth_type_trans(skb, skb->dev);
-+	return netif_rx(skb);
-+}
-+
- struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id)
- {
- 	struct phy_device *dev;
-@@ -67,6 +79,8 @@ struct phy_device* phy_device_create(str
- 	dev->bus = bus;
- 
- 	dev->state = PHY_DOWN;
-+	dev->netif_receive_skb = &generic_receive_skb;
-+	dev->netif_rx = &generic_rx;
- 
- 	spin_lock_init(&dev->lock);
- 
---- a/include/linux/phy.h
-+++ b/include/linux/phy.h
-@@ -289,6 +289,17 @@ struct phy_device {
- 	void (*adjust_link)(struct net_device *dev);
- 
- 	void (*adjust_state)(struct net_device *dev);
-+
-+	/*
-+	 * By default these point to the original functions
-+	 * with the same name. adding them to the phy_device
-+	 * allows the phy driver to override them for packet
-+	 * mangling if the ethernet driver supports it
-+	 * This is required to support some really horrible
-+	 * switches such as the Marvell 88E6060
-+	 */
-+	int (*netif_receive_skb)(struct sk_buff *skb);
-+	int (*netif_rx)(struct sk_buff *skb);
- };
- #define to_phy_device(d) container_of(d, struct phy_device, dev)
- 
---- a/include/linux/netdevice.h
-+++ b/include/linux/netdevice.h
-@@ -426,6 +426,7 @@ struct net_device
- 	void			*ax25_ptr;	/* AX.25 specific data */
- 	struct wireless_dev	*ieee80211_ptr;	/* IEEE 802.11 specific data,
- 						   assign before registering */
-+	void			*phy_ptr; /* PHY device specific data */
- 
- /*
-  * Cache line mostly used on receive path (including eth_type_trans())

target/linux/generic-2.6/patches-2.6.23/640-mvswitch.patch

@@ -1,46 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -65,6 +65,12 @@ config ADM6996_PHY
- 	---help---
- 	  Currently supports the ADM6996F switch
- 
-+config MVSWITCH_PHY
-+	tristate "Driver for Marvell switches"
-+	select VLAN_8021Q
-+	---help---
-+	  Currently supports the Marvell 88E6060 switch.
-+
- config FIXED_PHY
- 	tristate "Drivers for PHY emulation on fixed speed/link"
- 	---help---
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -13,4 +13,5 @@ obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
- obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
- obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
- obj-$(CONFIG_ADM6996_PHY)	+= adm6996.o
-+obj-$(CONFIG_MVSWITCH_PHY)	+= mvswitch.o
- obj-$(CONFIG_FIXED_PHY)		+= fixed.o
---- a/drivers/net/phy/mdio_bus.c
-+++ b/drivers/net/phy/mdio_bus.c
-@@ -35,6 +35,12 @@
- #include <asm/irq.h>
- #include <asm/uaccess.h>
- 
-+static void mdio_dev_release(struct device *dev)
-+{
-+	/* nothing to do */
-+}
-+
-+
- /**
-  * mdiobus_register - bring up all the PHYs on a given bus and attach them to bus
-  * @bus: target mii_bus
-@@ -85,6 +91,7 @@ int mdiobus_register(struct mii_bus *bus
- 
- 			phydev->dev.parent = bus->dev;
- 			phydev->dev.bus = &mdio_bus_type;
-+			phydev->dev.release = mdio_dev_release;
- 			snprintf(phydev->dev.bus_id, BUS_ID_SIZE, PHY_ID_FMT, bus->id, i);
- 
- 			phydev->bus = bus;

target/linux/generic-2.6/patches-2.6.25/610-phy_detect.patch

@@ -1,26 +0,0 @@
---- a/drivers/net/phy/mdio_bus.c
-+++ b/drivers/net/phy/mdio_bus.c
-@@ -132,6 +132,9 @@ static int mdio_bus_match(struct device 
- 	struct phy_device *phydev = to_phy_device(dev);
- 	struct phy_driver *phydrv = to_phy_driver(drv);
- 
-+	if (phydrv->detect)
-+		return (phydrv->detect(phydev->bus, phydev->addr));
-+
- 	return ((phydrv->phy_id & phydrv->phy_id_mask) ==
- 		(phydev->phy_id & phydrv->phy_id_mask));
- }
---- a/include/linux/phy.h
-+++ b/include/linux/phy.h
-@@ -325,6 +325,11 @@ struct phy_driver {
- 	u32 features;
- 	u32 flags;
- 
-+	/* Called during discovery to test if the
-+	 * device can attach to the bus, even if
-+	 * phy id and mask do not match */
-+	bool (*detect)(struct mii_bus *bus, int addr);
-+
- 	/* Called to initialize the PHY,
- 	 * including after a reset */
- 	int (*config_init)(struct phy_device *phydev);

target/linux/generic-2.6/patches-2.6.25/620-phy_adm6996.patch

@@ -1,24 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -65,6 +65,11 @@ config REALTEK_PHY
- 	---help---
- 	  Supports the Realtek 821x PHY.
- 
-+config ADM6996_PHY
-+	tristate "Driver for ADM6996 switches"
-+	---help---
-+	  Currently supports the ADM6996F switch
-+
- config FIXED_PHY
- 	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
- 	depends on PHYLIB=y
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -12,6 +12,7 @@ obj-$(CONFIG_SMSC_PHY)		+= smsc.o
- obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
- obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
- obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
-+obj-$(CONFIG_ADM6996_PHY)	+= adm6996.o
- obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
- obj-$(CONFIG_FIXED_PHY)		+= fixed.o
- obj-$(CONFIG_MDIO_BITBANG)	+= mdio-bitbang.o

target/linux/generic-2.6/patches-2.6.25/630-phy_packets.patch

@@ -1,60 +0,0 @@
---- a/drivers/net/phy/phy_device.c
-+++ b/drivers/net/phy/phy_device.c
-@@ -53,6 +53,18 @@ static void phy_device_release(struct de
- 	phy_device_free(to_phy_device(dev));
- }
- 
-+static int generic_receive_skb(struct sk_buff *skb)
-+{
-+	skb->protocol = eth_type_trans(skb, skb->dev);
-+	return netif_receive_skb(skb);
-+}
-+
-+static int generic_rx(struct sk_buff *skb)
-+{
-+	skb->protocol = eth_type_trans(skb, skb->dev);
-+	return netif_rx(skb);
-+}
-+
- struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id)
- {
- 	struct phy_device *dev;
-@@ -78,6 +90,8 @@ struct phy_device* phy_device_create(str
- 	dev->bus = bus;
- 
- 	dev->state = PHY_DOWN;
-+	dev->netif_receive_skb = &generic_receive_skb;
-+	dev->netif_rx = &generic_rx;
- 
- 	mutex_init(&dev->lock);
- 
---- a/include/linux/phy.h
-+++ b/include/linux/phy.h
-@@ -295,6 +295,17 @@ struct phy_device {
- 	void (*adjust_link)(struct net_device *dev);
- 
- 	void (*adjust_state)(struct net_device *dev);
-+
-+	/*
-+	 * By default these point to the original functions
-+	 * with the same name. adding them to the phy_device
-+	 * allows the phy driver to override them for packet
-+	 * mangling if the ethernet driver supports it
-+	 * This is required to support some really horrible
-+	 * switches such as the Marvell 88E6060
-+	 */
-+	int (*netif_receive_skb)(struct sk_buff *skb);
-+	int (*netif_rx)(struct sk_buff *skb);
- };
- #define to_phy_device(d) container_of(d, struct phy_device, dev)
- 
---- a/include/linux/netdevice.h
-+++ b/include/linux/netdevice.h
-@@ -595,6 +595,7 @@ struct net_device
- 	void			*ax25_ptr;	/* AX.25 specific data */
- 	struct wireless_dev	*ieee80211_ptr;	/* IEEE 802.11 specific data,
- 						   assign before registering */
-+	void			*phy_ptr; /* PHY device specific data */
- 
- /*
-  * Cache line mostly used on receive path (including eth_type_trans())

target/linux/generic-2.6/patches-2.6.25/640-mvswitch.patch

@@ -1,48 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -70,6 +70,12 @@ config ADM6996_PHY
- 	---help---
- 	  Currently supports the ADM6996F switch
- 
-+config MVSWITCH_PHY
-+	tristate "Driver for Marvell switches"
-+	select VLAN_8021Q
-+	---help---
-+	  Currently supports the Marvell 88E6060 switch.
-+
- config FIXED_PHY
- 	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
- 	depends on PHYLIB=y
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -13,6 +13,7 @@ obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
- obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
- obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
- obj-$(CONFIG_ADM6996_PHY)	+= adm6996.o
-+obj-$(CONFIG_MVSWITCH_PHY)	+= mvswitch.o
- obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
- obj-$(CONFIG_FIXED_PHY)		+= fixed.o
- obj-$(CONFIG_MDIO_BITBANG)	+= mdio-bitbang.o
---- a/drivers/net/phy/mdio_bus.c
-+++ b/drivers/net/phy/mdio_bus.c
-@@ -35,6 +35,12 @@
- #include <asm/irq.h>
- #include <asm/uaccess.h>
- 
-+static void mdio_dev_release(struct device *dev)
-+{
-+	/* nothing to do */
-+}
-+
-+
- /**
-  * mdiobus_register - bring up all the PHYs on a given bus and attach them to bus
-  * @bus: target mii_bus
-@@ -85,6 +91,7 @@ int mdiobus_register(struct mii_bus *bus
- 
- 			phydev->dev.parent = bus->dev;
- 			phydev->dev.bus = &mdio_bus_type;
-+			phydev->dev.release = mdio_dev_release;
- 			snprintf(phydev->dev.bus_id, BUS_ID_SIZE, PHY_ID_FMT, bus->id, i);
- 
- 			phydev->bus = bus;