lantiq: add support for VGV7519 KPN Experia box v8

Signed-off-by: Maikel Bloemendal <[email protected]>
Signed-off-by: John Crispin <[email protected]>

SVN-Revision: 38266

target/linux/lantiq/dts/VGV7519.dtsi

@@ -0,0 +1,307 @@
+/include/ "vr9.dtsi"
+
+/ {
+	chosen {
+		bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+	};
+
+	memory@0 {
+		reg = <0x0 0x4000000>;
+	};
+	
+	fpi@10000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,fpi", "simple-bus";
+		ranges = <0x0 0x10000000 0xEEFFFFF>;
+		reg = <0x10000000 0xEF00000>;
+
+		localbus@0 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			compatible = "lantiq,localbus", "simple-bus";
+		};
+
+		gpio: pinmux@E100B10 {
+			compatible = "lantiq,pinctrl-xr9";
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+			
+			interrupt-parent = <&icu0>;
+			interrupts = <166 135 66 40 41 42 38>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+			reg = <0xE100B10 0xA0>;
+
+			state_default: pinmux {
+				exin3 {
+					lantiq,groups = "exin3";
+					lantiq,function = "exin";
+				};
+				stp {
+					lantiq,groups = "stp";
+					lantiq,function = "stp";
+				};
+				spi {
+					lantiq,groups = "spi", "spi_cs4";
+					lantiq,function = "spi";
+				};
+				mdio {
+					lantiq,groups = "mdio";
+					lantiq,function = "mdio";
+				};
+				pci {
+					lantiq,groups = "gnt1", "req1";
+					lantiq,function = "pci";
+				};
+				conf_out {
+					lantiq,pins = "io4", "io5", "io6", /* stp */
+							"io21",
+							"io33",
+							"io7", "io44"; /* Internal ethernet phy leds */
+					lantiq,open-drain;
+					lantiq,pull = <0>;
+					lantiq,output = <1>;
+				};
+				pcie-rst {
+					lantiq,pins = "io38";
+					lantiq,pull = <0>;
+					lantiq,output = <1>;
+				};
+				conf_in {
+					lantiq,pins = "io39"; /* exin3 */
+					lantiq,pull = <2>;
+				};
+			};
+		};
+
+		eth@E108000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "lantiq,xrx200-net";
+			reg = <	0xE108000 0x3000 /* switch */
+				0xE10B100 0x70 /* mdio */
+				0xE10B1D8 0x30 /* mii */
+				0xE10B308 0x30 /* pmac */
+			>;
+			interrupt-parent = <&icu0>;
+			interrupts = <73 72>;
+
+			lan: interface@0 {
+				compatible = "lantiq,xrx200-pdi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				mac-address = [ 00 11 22 33 44 55 ];
+
+				ethernet@0 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <0>;
+					phy-mode = "rgmii";
+					phy-handle = <&phy0>;
+				};
+				ethernet@1 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <1>;
+					phy-mode = "rgmii";
+					phy-handle = <&phy1>;
+				};
+				ethernet@2 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <2>;
+					phy-mode = "gmii";
+					phy-handle = <&phy11>;
+				};
+				ethernet@4 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <4>;
+					phy-mode = "gmii";
+					phy-handle = <&phy13>;
+				};
+			};
+
+			wan: interface@1 {
+				compatible = "lantiq,xrx200-pdi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+				mac-address = [ 00 11 22 33 44 56 ];
+				lantiq,wan;
+				ethernet@5 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <5>;
+					phy-mode = "rgmii";
+					phy-handle = <&phy5>;
+				};
+			};
+
+			mdio@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "lantiq,xrx200-mdio";
+				phy0: ethernet-phy@0 {
+					reg = <0x0>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+					lantiq,c45-reg-init = <1 0 0 0>; 
+				};
+				phy1: ethernet-phy@1 {
+					reg = <0x1>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+					lantiq,c45-reg-init = <1 0 0 0>; 
+				};
+				phy5: ethernet-phy@5 {
+					reg = <0x5>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+					lantiq,c45-reg-init = <1 0 0 0>; 
+				};
+				phy11: ethernet-phy@11 {
+					reg = <0x11>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+					lantiq,c45-reg-init = <1 0 0 0>; 
+				};
+				phy13: ethernet-phy@13 {
+					reg = <0x13>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+					lantiq,c45-reg-init = <1 0 0 0>; 
+				};
+			};
+		};
+
+		stp: stp@E100BB0 {
+			compatible = "lantiq,gpio-stp-xway";
+			reg = <0xE100BB0 0x40>;
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			lantiq,shadow = <0xffff>;
+			lantiq,groups = <0x3>;
+			lantiq,dsl = <0x0>;
+			lantiq,phy1 = <0x0>;
+			lantiq,phy2 = <0x0>;
+			/* lantiq,rising; */
+		};
+
+		ifxhcd@E101000 {
+			status = "okay";
+			gpios = <&gpio 33 0>;
+			lantiq,portmask = <0x3>;
+		};
+
+		pci@E105400 {
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			compatible = "lantiq,pci-xway1";
+			bus-range = <0x0 0x0>;
+			ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000   /* pci memory */
+				0x1000000 0 0x00000000 0xAE00000 0 0x200000>; /* io space */
+			reg = <0x7000000 0x8000         /* config space */
+				0xE105400 0x400>;       /* pci bridge */
+			lantiq,bus-clock = <33333333>;
+			/*lantiq,external-clock;*/
+			lantiq,delay-hi = <0>; /* 0ns delay */
+			lantiq,delay-lo = <0>; /* 0.0ns delay */
+			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+			interrupt-map = <
+				0x7000 0 0 1 &icu0 29 1 // slot 14, irq 29
+				>;
+			gpios-reset = <&gpio 21 0>;
+			req-mask = <0x1>;	/* GNT1 */
+		};
+	};
+
+	gphy-xrx200 {
+		compatible = "lantiq,phy-xrx200";
+		firmware = "lantiq/vr9_phy11g_a1x.bin";
+		phys = [ 00 01 ];
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+		reset {
+			label = "reset";
+			gpios = <&gpio 9 1>;
+			linux,code = <0x198>;
+		};
+		eco {
+			label = "eco";
+			gpios = <&gpio 41 1>;
+			linux,code = <247>;
+		};
+		rfkill {
+			label = "rfkill";
+			gpios = <&gpio 45 1>;
+			linux,code = <0xf7>;
+		};
+		wps {
+			gpios = <&gpio 10 1>;
+			linux,code = <0x211>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		eco {					/* blue */
+			label = "eco";
+			gpios = <&stp 2 1>;
+		};
+		wps_red {				/* red */
+			label = "wps_red";
+			gpios = <&stp 3 1>;
+		};
+		wps_yellow {				/* yellow */
+			label = "wps_yellow";
+			gpios = <&stp 4 1>;
+		};
+		upgrade {				/* blue */
+			label = "upgrade";
+			gpios = <&stp 5 1>;
+		};
+		tv {					/* yellow */
+			label = "tv";
+			gpios = <&stp 6 1>;
+		};
+		internet_yellow {			/* yellow */
+			label = "internet_yellow";
+			gpios = <&stp 7 1>;
+		};
+		internet_red {				/* red */
+			label = "internet_red";
+			gpios = <&stp 8 1>;
+		};
+		broadband_red {				/* red */
+			label = "broadband_red";
+			gpios = <&stp 9 1>;
+		};
+		broadband_yellow {			/* yellow */
+			label = "broadband_yellow";
+			gpios = <&stp 10 1>;
+		};
+		voice {					/* yellow */
+			label = "voice";
+			gpios = <&stp 11 1>;
+		};
+		wireless_red {				/* red */
+			label = "wireless_red";
+			gpios = <&stp 12 1>;
+		};
+		wireless_yellow {			/* yellow */
+			label = "wireless_yellow";
+			gpios = <&stp 13 1>;
+		};
+		power2 {				/* yellow */
+			label = "power2";
+			gpios = <&stp 14 1>;
+		};
+		power {					/* red */
+			label = "power";
+			gpios = <&stp 15 1>;
+			default-state = "on";
+		};
+	};
+};

target/linux/lantiq/dts/VGV7519BRN.dts

@@ -0,0 +1,28 @@
+/dts-v1/;
+
+
+/include/ "VGV7519.dtsi"
+
+/ {
+	fpi@10000000 {
+		localbus@0 {
+			nor-flash@0 {
+				compatible = "lantiq,nor", "cfi-flash";
+				bank-width = <2>;
+				reg = <0 0x0 0x800000>, <1 0x800000 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x780000>;
+					read-only;
+				};
+				partition@880000 {
+					label = "rootfs_data";
+					reg = <0x880000 0x780000>;
+				};
+			};
+		};
+	};
+};

target/linux/lantiq/dts/VGV7519NOR.dts

@@ -0,0 +1,36 @@
+/dts-v1/;
+
+
+/include/ "VGV7519.dtsi"
+
+/ {
+	fpi@10000000 {
+		localbus@0 {
+			nor-boot@0 {
+				compatible = "lantiq,nor";
+				bank-width = <2>;
+				reg = <0 0x0 0x800000>, <1 0x800000 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "uboot";
+					reg = <0x00000 0x40000>;
+				};
+
+				partition@60000 {
+					label = "uboot_env";
+					reg = <0x60000 0x10000>;
+				};
+
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0xf80000>;
+					// 0x080000 - 0x01b0000 : kernel
+					// 0x1b0000 - 0x1000000 : rootfs (squashfs)
+					// 0x390000 - 0x1000000 : rootfs_data
+				};
+			};
+		};
+	};
+};

target/linux/lantiq/image/Makefile

@@ -282,6 +282,12 @@ Image/Build/Profile/VG3503J=$(call Image/BuildLoader/$(1),$(1),VG3503J)
 Image/BuildKernel/Profile/TDW8970=$(call Image/BuildKernelTPLink/Template,TDW8970,TD-W8970v1,$(1))
 Image/Build/Profile/TDW8970=$(call Image/BuildTPLink/$(1),$(1),TDW8970,TD-W8970v1)
 
+Image/BuildKernel/Profile/VGV7519NOR=$(call Image/BuildKernel/Template,VGV7519NOR,$(1))
+Image/Build/Profile/VGV7519NOR=$(call Image/Build/$(1),$(1),VGV7519NOR)
+
+Image/BuildKernel/Profile/VGV7519BRN=$(call Image/BuildKernel/Template,VGV7519BRN,$(1))
+Image/Build/Profile/VGV7519BRN=$(call Image/Build/$(1),$(1),VGV7519BRN,5D00008000,0x12345678,$(1))
+
 endif
 
 

target/linux/lantiq/xrx200/profiles/arv.mk

@@ -5,3 +5,25 @@ define Profile/VG3503J
 endef
 
 $(eval $(call Profile,VG3503J))
+
+define Profile/VGV7519NOR
+  NAME:=Lantiq VR9 - VGV7519NOR
+  PACKAGES:=kmod-ath9k wpad-mini \
+	kmod-ltq-deu-vr9 kmod-ltq-hcd-vr9 \
+	kmod-ltq-vdsl-vr9-mei kmod-ltq-vdsl-vr9 \
+	kmod-ltq-atm-vr9 ltq-vdsl-vr9-fw-installer \
+	ltq-vdsl-app ppp-mod-pppoa
+endef
+
+$(eval $(call Profile,VGV7519NOR))
+
+define Profile/VGV7519BRN
+  NAME:=Lantiq VR9 - VGV7519 (BRN)
+  PACKAGES:=kmod-ath9k wpad-mini \
+	kmod-ltq-deu-vr9 kmod-ltq-hcd-vr9 \
+	kmod-ltq-vdsl-vr9-mei kmod-ltq-vdsl-vr9 \
+	kmod-ltq-atm-vr9 ltq-vdsl-vr9-fw-installer \
+	ltq-vdsl-app ppp-mod-pppoa
+endef
+
+$(eval $(call Profile,VGV7519BRN))