imx6: remove linux 4.4 support

Signed-off-by: Felix Fietkau <[email protected]>

target/linux/imx6/config-4.4

@@ -1,461 +0,0 @@
-CONFIG_AHCI_IMX=y
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-CONFIG_ARCH_HAS_RESET_CONTROLLER=y
-CONFIG_ARCH_HAS_SG_CHAIN=y
-CONFIG_ARCH_HAS_TICK_BROADCAST=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-# CONFIG_ARCH_MULTI_CPU_AUTO is not set
-CONFIG_ARCH_MULTI_V6_V7=y
-CONFIG_ARCH_MULTI_V7=y
-CONFIG_ARCH_MXC=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
-CONFIG_ARM=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_CRYPTO=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_ARM_ERRATA_764369=y
-CONFIG_ARM_ERRATA_775420=y
-CONFIG_ARM_GIC=y
-CONFIG_ARM_HAS_SG_CHAIN=y
-CONFIG_ARM_HEAVY_MB=y
-CONFIG_ARM_IMX6Q_CPUFREQ=y
-CONFIG_ARM_L1_CACHE_SHIFT=6
-CONFIG_ARM_L1_CACHE_SHIFT_6=y
-# CONFIG_ARM_LPAE is not set
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-CONFIG_ARM_PMU=y
-CONFIG_ARM_THUMB=y
-# CONFIG_ARM_THUMBEE is not set
-CONFIG_ARM_VIRT_EXT=y
-CONFIG_ATA=y
-CONFIG_ATAGS=y
-# CONFIG_ATA_SFF is not set
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_CACHE_L2X0=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_IMX_GPT=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLKSRC_OF=y
-CONFIG_CLKSRC_PROBE=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_COMMON_CLK=y
-CONFIG_CONFIGFS_FS=m
-CONFIG_CPUFREQ_DT=y
-CONFIG_CPU_32v6K=y
-CONFIG_CPU_32v7=y
-CONFIG_CPU_ABRT_EV7=y
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-CONFIG_CPU_CACHE_V7=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
-CONFIG_CPU_FREQ_GOV_COMMON=y
-CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
-CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-CONFIG_CPU_FREQ_GOV_POWERSAVE=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=y
-CONFIG_CPU_FREQ_STAT=y
-CONFIG_CPU_FREQ_STAT_DETAILS=y
-CONFIG_CPU_HAS_ASID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_V7=y
-CONFIG_CPU_RMAP=y
-CONFIG_CPU_THERMAL=y
-CONFIG_CPU_TLB_V7=y
-CONFIG_CPU_V7=y
-CONFIG_CRC16=y
-CONFIG_CRYPTO_ABLK_HELPER=y
-CONFIG_CRYPTO_AEAD=y
-CONFIG_CRYPTO_AEAD2=y
-CONFIG_CRYPTO_AES_ARM=y
-CONFIG_CRYPTO_AES_ARM_BS=y
-# CONFIG_CRYPTO_AES_ARM_CE is not set
-CONFIG_CRYPTO_AUTHENC=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_CRYPTD=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_DEV_FSL_CAAM=y
-CONFIG_CRYPTO_DEV_FSL_CAAM_AHASH_API=y
-CONFIG_CRYPTO_DEV_FSL_CAAM_CRYPTO_API=y
-# CONFIG_CRYPTO_DEV_FSL_CAAM_DEBUG is not set
-CONFIG_CRYPTO_DEV_FSL_CAAM_IMX=y
-# CONFIG_CRYPTO_DEV_FSL_CAAM_INTC is not set
-CONFIG_CRYPTO_DEV_FSL_CAAM_JR=y
-CONFIG_CRYPTO_DEV_FSL_CAAM_LE=y
-CONFIG_CRYPTO_DEV_FSL_CAAM_RINGSIZE=9
-CONFIG_CRYPTO_DEV_FSL_CAAM_RNG_API=y
-# CONFIG_CRYPTO_GHASH_ARM_CE is not set
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_MANAGER=y
-CONFIG_CRYPTO_MANAGER2=y
-CONFIG_CRYPTO_NULL=y
-CONFIG_CRYPTO_NULL2=y
-CONFIG_CRYPTO_RNG=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_CRYPTO_SHA1_ARM=y
-# CONFIG_CRYPTO_SHA1_ARM_CE is not set
-CONFIG_CRYPTO_SHA1_ARM_NEON=y
-CONFIG_CRYPTO_SHA256_ARM=y
-# CONFIG_CRYPTO_SHA2_ARM_CE is not set
-CONFIG_CRYPTO_SHA512_ARM=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DCACHE_WORD_ACCESS=y
-CONFIG_DEBUG_IMX_UART_PORT=1
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_UART_8250 is not set
-# CONFIG_DEBUG_USER is not set
-CONFIG_DECOMPRESS_BZIP2=y
-CONFIG_DECOMPRESS_GZIP=y
-CONFIG_DECOMPRESS_LZO=y
-CONFIG_DECOMPRESS_XZ=y
-CONFIG_DMADEVICES=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_OF=y
-CONFIG_DTC=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-# CONFIG_ENABLE_DEFAULT_TRACERS is not set
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT2_FS_SECURITY=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_EXT3_FS_SECURITY=y
-CONFIG_EXT4_FS=y
-CONFIG_EXT4_FS_POSIX_ACL=y
-CONFIG_EXT4_FS_SECURITY=y
-CONFIG_EXTCON=y
-CONFIG_FEC=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FRAME_POINTER=y
-CONFIG_FS_MBCACHE=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_FTRACE=y
-# CONFIG_FTRACE_SYSCALLS is not set
-CONFIG_GATEWORKS_GW16083=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-# CONFIG_GIANFAR is not set
-CONFIG_GLOB=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_GENERIC=y
-CONFIG_GPIO_MXC=y
-CONFIG_GPIO_PCA953X=y
-CONFIG_GPIO_PCA953X_IRQ=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_AUDITSYSCALL=y
-CONFIG_HAVE_ARCH_BITREVERSE=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_ARM_SCU=y
-CONFIG_HAVE_ARM_TWD=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_HW_BREAKPOINT=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IMX_ANATOP=y
-CONFIG_HAVE_IMX_GPC=y
-CONFIG_HAVE_IMX_MMDC=y
-CONFIG_HAVE_IMX_SRC=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SMP=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ_FIXED=0
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_IMX=y
-CONFIG_IMX2_WDT=y
-CONFIG_IMX_DMA=y
-CONFIG_IMX_SDMA=y
-CONFIG_IMX_THERMAL=y
-# CONFIG_IMX_WEIM is not set
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IOMMU_HELPER=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_DOMAIN_HIERARCHY=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_JBD2=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_SPIN_ON_OWNER=y
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MDIO_BOARDINFO=y
-CONFIG_MFD_SYSCON=y
-CONFIG_MICREL_PHY=y
-CONFIG_MIGHT_HAVE_CACHE_L2X0=y
-CONFIG_MIGHT_HAVE_PCI=y
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-# CONFIG_MMC_MXC is not set
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_ESDHC_IMX=y
-CONFIG_MMC_SDHCI_IO_ACCESSORS=y
-# CONFIG_MMC_SDHCI_PCI is not set
-CONFIG_MMC_SDHCI_PLTFM=y
-# CONFIG_MMC_TIFM_SD is not set
-CONFIG_MODULES_TREE_LOOKUP=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_GPMI_NAND=y
-# CONFIG_MTD_PHYSMAP_OF is not set
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-# CONFIG_MTD_UBI_FASTMAP is not set
-# CONFIG_MTD_UBI_GLUEBI is not set
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_MUTEX_SPIN_ON_OWNER=y
-# CONFIG_MX3_IPU is not set
-CONFIG_MXS_DMA=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEON=y
-CONFIG_NET_FLOW_LIMIT=y
-CONFIG_NET_PTP_CLASSIFY=y
-CONFIG_NLS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NO_BOOTMEM=y
-CONFIG_NO_HZ_COMMON=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_NR_CPUS=4
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_ADDRESS_PCI=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_MDIO=y
-CONFIG_OF_MTD=y
-CONFIG_OF_NET=y
-CONFIG_OF_PCI=y
-CONFIG_OF_PCI_IRQ=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_OUTER_CACHE=y
-CONFIG_OUTER_CACHE_SYNC=y
-CONFIG_PADATA=y
-CONFIG_PAGE_OFFSET=0x80000000
-CONFIG_PCI=y
-CONFIG_PCIEAER=y
-CONFIG_PCIEPORTBUS=y
-CONFIG_PCIE_DW=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_DOMAINS_GENERIC=y
-CONFIG_PCI_IMX6=y
-CONFIG_PERF_EVENTS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_IMX=y
-CONFIG_PINCTRL_IMX6Q=y
-CONFIG_PINCTRL_IMX6SL=y
-CONFIG_PINCTRL_IMX6SX=y
-CONFIG_PINCTRL_IMX6UL=y
-# CONFIG_PINCTRL_SINGLE is not set
-CONFIG_PL310_ERRATA_588369=y
-CONFIG_PL310_ERRATA_727915=y
-# CONFIG_PL310_ERRATA_753970 is not set
-CONFIG_PL310_ERRATA_769419=y
-CONFIG_PM_OPP=y
-CONFIG_PPS=y
-# CONFIG_PROBE_EVENTS is not set
-CONFIG_PTP_1588_CLOCK=y
-CONFIG_PWM=y
-CONFIG_PWM_IMX=y
-CONFIG_PWM_SYSFS=y
-CONFIG_RAS=y
-CONFIG_RATIONAL=y
-CONFIG_RCU_STALL_COMMON=y
-CONFIG_RD_BZIP2=y
-CONFIG_RD_GZIP=y
-CONFIG_RD_LZO=y
-CONFIG_RD_XZ=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_I2C=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_REGMAP_SPI=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_ANATOP=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_PFUZE100=y
-CONFIG_RFS_ACCEL=y
-CONFIG_RPS=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_DS1307=y
-CONFIG_RTC_DRV_DS1672=y
-# CONFIG_RTC_DRV_IMXDI is not set
-# CONFIG_RTC_DRV_MXC is not set
-CONFIG_RTC_DRV_SNVS=y
-CONFIG_RWSEM_SPIN_ON_OWNER=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_SATA_AHCI_PLATFORM=y
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCHED_INFO is not set
-CONFIG_SCSI=y
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_IMX=y
-CONFIG_SERIAL_IMX_CONSOLE=y
-CONFIG_SMP=y
-CONFIG_SMP_ON_UP=y
-CONFIG_SOC_BUS=y
-# CONFIG_SOC_IMX50 is not set
-# CONFIG_SOC_IMX51 is not set
-# CONFIG_SOC_IMX53 is not set
-CONFIG_SOC_IMX6=y
-CONFIG_SOC_IMX6Q=y
-CONFIG_SOC_IMX6SL=y
-CONFIG_SOC_IMX6SX=y
-CONFIG_SOC_IMX6UL=y
-# CONFIG_SOC_IMX7D is not set
-# CONFIG_SOC_LS1021A is not set
-# CONFIG_SOC_VF610 is not set
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_IMX=y
-CONFIG_SPI_MASTER=y
-CONFIG_SRAM=y
-CONFIG_SRCU=y
-CONFIG_STMP_DEVICE=y
-CONFIG_SWIOTLB=y
-CONFIG_SWP_EMULATE=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_OF=y
-CONFIG_THERMAL_WRITABLE_TRIPS=y
-# CONFIG_THUMB2_KERNEL is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TRACING_EVENTS_GPIO=y
-CONFIG_TREE_RCU=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_UBIFS_FS_LZO=y
-CONFIG_UBIFS_FS_ZLIB=y
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_USB=y
-CONFIG_USB_CHIPIDEA=y
-# CONFIG_USB_CHIPIDEA_DEBUG is not set
-CONFIG_USB_CHIPIDEA_HOST=y
-CONFIG_USB_CHIPIDEA_OF=y
-CONFIG_USB_CHIPIDEA_UDC=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_EHCI_HCD=y
-# CONFIG_USB_EHCI_HCD_PLATFORM is not set
-# CONFIG_USB_EHCI_MXC is not set
-CONFIG_USB_EHCI_PCI=y
-CONFIG_USB_ETH=m
-# CONFIG_USB_ETH_EEM is not set
-CONFIG_USB_ETH_RNDIS=y
-CONFIG_USB_F_ECM=m
-CONFIG_USB_F_RNDIS=m
-CONFIG_USB_F_SUBSET=m
-CONFIG_USB_GADGET=y
-# CONFIG_USB_IMX21_HCD is not set
-CONFIG_USB_LIBCOMPOSITE=m
-CONFIG_USB_MXS_PHY=y
-CONFIG_USB_PHY=y
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-CONFIG_USB_U_ETHER=m
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VFP=y
-CONFIG_VFPv3=y
-CONFIG_VMSPLIT_2G=y
-# CONFIG_VMSPLIT_3G is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XPS=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZONE_DMA_FLAG=0

target/linux/imx6/files-4.4/arch/arm/boot/dts/imx6dl-gw553x.dts

@@ -1,19 +0,0 @@
-/*
- * Copyright 2015 Gateworks Corporation
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-gw553x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 DualLite/Solo GW553X";
-	compatible = "gw,imx6dl-gw553x", "gw,ventana", "fsl,imx6dl";
-};

target/linux/imx6/files-4.4/arch/arm/boot/dts/imx6q-gw553x.dts

@@ -1,19 +0,0 @@
-/*
- * Copyright 2015 Gateworks Corporation
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-gw553x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Dual/Quad GW553X";
-	compatible = "gw,imx6q-gw553x", "gw,ventana", "fsl,imx6q";
-};

target/linux/imx6/files-4.4/arch/arm/boot/dts/imx6qdl-gw553x.dtsi

@@ -1,547 +0,0 @@
-/*
- * Copyright 2016 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	/* these are used by bootloader for disabling nodes */
-	aliases {
-		led0 = &led0;
-		led1 = &led1;
-		nand = &gpmi;
-		usb0 = &usbh1;
-		usb1 = &usbotg;
-	};
-
-	chosen {
-		bootargs = "console=ttymxc1,115200";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_leds>;
-
-		led0: user1 {
-			label = "user1";
-			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
-			default-state = "on";
-			linux,default-trigger = "heartbeat";
-		};
-
-		led1: user2 {
-			label = "user2";
-			gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
-			default-state = "off";
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		user_pb {
-			label = "user_pb";
-
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
-			linux,code = <256>;
-		};
-	};
-
-	memory {
-		reg = <0x10000000 0x20000000>;
-	};
-
-	pps {
-		compatible = "pps-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pps>;
-		gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-		status = "okay";
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P0V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_5p0v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "5P0V";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-	};
-};
-
-&gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	status = "okay";
-};
-
-&hdmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hdmi>;
-	ddc-i2c-bus = <&i2c3>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	eeprom1: eeprom@50 {
-		compatible = "atmel,24c02";
-		reg = <0x50>;
-		pagesize = <16>;
-	};
-
-	eeprom2: eeprom@51 {
-		compatible = "atmel,24c02";
-		reg = <0x51>;
-		pagesize = <16>;
-	};
-
-	eeprom3: eeprom@52 {
-		compatible = "atmel,24c02";
-		reg = <0x52>;
-		pagesize = <16>;
-	};
-
-	eeprom4: eeprom@53 {
-		compatible = "atmel,24c02";
-		reg = <0x53>;
-		pagesize = <16>;
-	};
-
-	gsc: gsc@20 {
-		compatible = "gw,gsc";
-		reg = <0x20>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gsc>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <1>;
-
-		/* GSC watchdog */
-		watchdog {
-			compatible = "gw,gsc_wdt";
-			status = "okay";
-		};
-
-		/* Linux input events from GSC interrupt events */
-		input {
-			compatible = "gw,gsc_input";
-			interrupt-parent = <&gsc>;
-			interrupts = <0 1 2 5 7>;
-			interrupt-names = "button", "key-erased", "eeprom-wp", "tamper", "button-held";
-			status = "okay";
-		};
-	};
-
-	gsc_gpio: pca9555@23 {
-		compatible = "nxp,pca9555";
-		reg = <0x23>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gsc>;
-		interrupts = <4>;
-	};
-
-	gsc_hwmon: hwmon@29 {
-		compatible = "gw,gsc_hwmon";
-		reg = <0x29>;
-	};
-
-	gsc_rtc: ds1672@68 {
-		compatible = "dallas,ds1672";
-		reg = <0x68>;
-	};
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	/* LSM9DS1 magnetic sensor */
-	lsm9ds1-m@0x1c {
-		compatible = "st,lsm9ds1-mag";
-		reg = <0x1C>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_imu_mag>;
-		gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* IRQ */
-		rot-matrix = /bits/ 16 <(1) (0) (0)
-			(0) (1) (0)
-			(0) (0) (1)>;
-		poll-interval = <100>;
-		min-interval = <13>;
-		fs-range = <0>;
-	};
-
-	/* LSM9DS1 accelerometer/gyroscope sensor */
-	lsm9ds1-ag@0x6a {
-		compatible = "st,lsm9ds1-acc-gyr";
-		reg = <0x6A>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_imu_acc>;
-		gpios = <&gpio7 13 GPIO_ACTIVE_LOW>, /* INT1 */
-		        <&gpio4 5  GPIO_ACTIVE_LOW>; /* INT2 */
-		rot-matrix = /bits/ 16 <(1) (0) (0)
-			(0) (1) (0)
-			(0) (0) (1)>;
-		g-poll-interval = <100>;
-		g-min-interval = <2>;
-		g-fs-range = <0>;
-		x-poll-interval = <100>;
-		x-min-interval = <1>;
-		x-fs-range = <0>;
-		aa-filter-bw = <0>;
-	};
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pcie>;
-	reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&pwm2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-	status = "disabled";
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-	status = "disabled";
-};
-
-&pwm4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
-	status = "disabled";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	status = "okay";
-};
-
-&usbh1 {
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&reg_3p3v>;
-	no-1-8-v; /* firmware will remove if board revision supports */
-	status = "okay";
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-};
-
-&iomuxc {
-	imx6qdl-gw553x {
-		pinctrl_gpmi_nand: gpminandgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
-				MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
-				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
-				MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
-				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
-				MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
-				MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
-				MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
-				MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
-				MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
-				MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
-				MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
-				MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
-				MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
-				MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
-			>;
-		};
-
-		pinctrl_gsc: gscgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04 		0x0001b0b0
-			 >;
-		};
-
-		pinctrl_hdmi: hdmigrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1f8b0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_imu_mag: gpioimxmaggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b0b0 /* IRQ */
-				MX6QDL_PAD_GPIO_7__GPIO1_IO07	0x1b0b0 /* data ready */
-			>;
-		};
-
-		pinctrl_imu_acc: gpioimxaccgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b0b0 /* INT1 */
-				MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b0b0 /* INT2 */
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x4001b0b0 /* Data enable */
-			>;
-		};
-
-		pinctrl_gpio_leds: gpioledsgrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
-				MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			>;
-		};
-
-		pinctrl_pcie: pciegrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x4001b0b0 /* PCIESKT_WDIS# */
-			>;
-		};
-
-		pinctrl_pps: ppsgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm2: pwm2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm4: pwm4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0 /* OTG_PWR_EN */
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x17059 /* CD */
-				MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x17059
-			>;
-		};
-
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x170b9 /* CD */
-				MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x170b9
-			>;
-		};
-
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x170f9 /* CD */
-				MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x170f9
-			>;
-		};
-
-		pinctrl_wdog: wdoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0
-			>;
-		};
-	};
-};

target/linux/imx6/files-4.4/drivers/net/phy/gw16083.c

@@ -1,1046 +0,0 @@
-/*
- * drivers/net/phy/gw16083.c
- *
- * Driver for GW16083 Ventana Ethernet Expansion Mezzanine
- *
- * Author: Tim Harvey
- *
- * Copyright (c) 2014 Tim Harvey <[email protected]>
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-/*
- * The GW16083 interfaces with a Ventana baseboard via the PCIe bus, an i2c
- * bus (i2c2), and a couple of GPIO's. On the PCIe bus is an i210 GigE with
- * its MAC connected to Port4 of a Marvell MV88E6176 7-port GigE switch via
- * MDIO and RGMII. Ports 0-3 are standard copper RJ45 but Ports 5 and 6
- * connect to Marvell MV88E1111 dual-mode Copper/Fiber PHY's over SGMII and
- * MDIO. The PHY's have both an RG45 for copper and an SFP module.
- */
-
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/unistd.h>
-#include <linux/i2c.h>
-#include <linux/interrupt.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/spinlock.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/phy.h>
-#include <linux/marvell_phy.h>
-#include <linux/of_platform.h>
-#include <linux/platform_device.h>
-
-#include <linux/io.h>
-#include <asm/irq.h>
-#include <net/dsa.h>
-#include <linux/uaccess.h>
-
-#include "gw16083.h"
-
-#undef FAIL_ON_CHECKSUM_ERR	/* fail to configure SFP if checksum bad */
-#define PORT_POWER_CONTROL	/* ports can be enabled/disabled via sysfs */
-#define PORT_MODE_CONTROL	/* ports 5/6 can have SFP/RJ45 mode forced */
-#define RGMII_DELAY_ON_PHY	/* implement Port5/6 tx/rx delay on PHY vs sw */
-
-MODULE_DESCRIPTION("GW16083 driver");
-MODULE_AUTHOR("Tim Harvey");
-MODULE_LICENSE("GPL");
-
-struct mv88e1111_port_state {
-	int port;
-	bool present;
-	bool serdes;
-	bool sfp_signal;
-	bool sfp_present;
-	bool sfp_compat;
-	bool sfp_enabled;
-	char sfp_id[64];
-};
-
-struct mv88e1111_priv {
-	struct phy_device		*phydev;
-	struct i2c_client		*client;
-	struct mv88e1111_port_state	port5;
-	struct mv88e1111_port_state	port6;
-	struct kobject			*sysfs_kobj;
-	struct delayed_work work;
-	struct workqueue_struct *workq;
-};
-
-enum {
-	mode_copper = 0,
-	mode_serdes = 1,
-};
-
-#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
-static struct dsa_chip_data switch_chip_data = {
-	.port_names = {
-		"lan4",
-		"lan3",
-		"lan2",
-		"lan1",
-		"cpu",
-		"lan5",
-		"lan6",
-	},
-};
-
-static struct dsa_platform_data switch_plat_data = {
-	.nr_chips       = 1,
-	.chip           = &switch_chip_data,
-};
-
-static struct platform_device switch_device = {
-	.name           = "dsa",
-	.id             = 0,
-	.num_resources  = 0,
-	.dev.platform_data = &switch_plat_data,
-};
-#endif
-
-static struct i2c_client *gw16083_client = NULL;
-
-static int gw16083_read_port_sfp(struct i2c_client *client,
-				 struct mv88e1111_port_state *state);
-
-/* read switch port register from port0-6 */
-u16 read_switch_port(struct phy_device *pdev, int port, u8 regaddr)
-{
-	return pdev->bus->read(pdev->bus, MV_BASE + port, regaddr);
-}
-
-/* write switch port register to port0-6 */
-int write_switch_port(struct phy_device *pdev, int port, u8 regaddr, u16 val)
-{
-	return pdev->bus->write(pdev->bus, MV_BASE + port, regaddr, val);
-}
-
-/*
- * read_switch_port_phy - write a register for a specific port on 88E6176
- * The 88E6176 PHY registers must be accessed thorugh the Global2 address
- * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
- */
-int read_switch_port_phy(struct phy_device *pdev, int port, u8 regaddr)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	u16 reg;
-	int i;
-
-	dev_dbg(&priv->client->dev, "read_phy: port%d reg=0x%02x\n", port,
-		regaddr);
-	reg = SMIBUSY | SMIMODE22 | SMIOP_READ;
-	reg |= port << DEVADDR;
-	reg |= regaddr << REGADDR;
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
-	for (i = 0; i < 10; i++) {
-		reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
-				      MV_SMI_PHY_COMMAND);
-		if (!(reg & (1<<15)))
-			break;
-		mdelay(1);
-	}
-	/* timeout */
-	if (i == 10)
-		return 0xffff;
-	reg = pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA);
-	return reg;
-}
-
-/*
- * write_switch_port_phy - write a register for a specific port on 88E6176
- * The 88E6176 PHY registers must be accessed thorugh the Global2 address
- * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
- */
-int write_switch_port_phy(struct phy_device *pdev, int port, u8 addr, u16 reg)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	int i;
-
-	dev_dbg(&priv->client->dev, "write_phy: port%d reg=0x%02x val=0x%04x\n",
-		port, addr, reg);
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA, reg);
-	reg = SMIBUSY | SMIMODE22 | SMIOP_WRITE;
-	reg |= port << DEVADDR;
-	reg |= addr << REGADDR;
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
-	for (i = 0; i < 10; i++) {
-		reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
-				      MV_SMI_PHY_COMMAND);
-		if (!(reg & (1<<15)))
-			break;
-		mdelay(1);
-	}
-	/* timeout */
-	if (i == 10)
-		return -ETIMEDOUT;
-
-	return 0;
-}
-
-/* read a scratch register from switch */
-inline u8 read_switch_scratch(struct phy_device *pdev, u8 reg)
-{
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC, (reg << 8));
-	return pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC) & 0xff;
-}
-
-/* write a scratch register to switch */
-inline void write_switch_scratch(struct phy_device *pdev, u8 reg, u8 val)
-{
-	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC,
-			 (1 << 15) | (reg << 8) | val);
-}
-
-/* enable or disable an SFP's TXEN signal */
-static int enable_sfp_txen(struct phy_device *pdev, int port, bool enable)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	u8 gpio;
-	int bit;
-
-	if (port != 5 && port != 6)
-		return -EINVAL;
-
-	/* GPIO[2:1] output low to enable TXEN */
-	bit = (port == 5) ? 1 : 2;
-	gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
-	if (enable)
-		gpio |= (1 << bit);
-	else
-		gpio &= (1 << bit);
-	write_switch_scratch(pdev, MV_GPIO_DATA, gpio);
-	dev_info(&priv->client->dev, "Port%d: SFP TX %s\n", port, enable ?
-		 "enabled" : "disabled");
-	return 0;
-}
-
-/* configure mv88e1111 port for copper or serdes
- *  For Copper we set auto link/duplex/speed detection
- *  For SerDes/Fiber we force 1000mbps link up and auto-neg duplex
- */
-static int config_mv88e1111_port_sfp(struct phy_device *pdev, int port,
-				     bool sfp)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	u16 reg;
-
-	if (port != 5 && port != 6)
-		return -EINVAL;
-
-	dev_dbg(&priv->client->dev, "%s: Port%d %s\n", __func__, port,
-		sfp ? "SFP" : "copper");
-	if (sfp) {
-		enable_sfp_txen(pdev, port, 1);
-
-		/* configure MV88E6176 Physical Control Port Register */
-		dev_info(&priv->client->dev,
-			 "Port%d: SFP: force 1000mbps link up "
-			 "(auto-negotiate duplex)\n",
-			 port);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-		reg &= ~0x3f; /* clear 5-0 */
-		reg |= (1 << 4) | (1 << 5); /* force link up */
-		reg |= 2; /* force 1000mbps */
-		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-	}
-
-	/* copper */
-	else {
-		enable_sfp_txen(pdev, port, 0);
-
-		/* configure MV88E6176 Physical Control Port Register */
-		dev_info(&priv->client->dev,
-			 "Port%d: Copper: set auto-neg link/duplex/speed\n",
-			 port);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-		reg &= ~0x3f; /* clear 5-0 */
-		reg |= 3; /* speed not forced */
-		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
-		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
-	}
-	dev_dbg(&priv->client->dev, "%s: Port%d %s PORT_PHYS_CONTROL=0x%04x\n",
-		__func__, port, sfp ? "SFP" : "copper",
-		read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL));
-
-	return 0;
-}
-
-#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352) && defined(PORT_POWER_CONTROL)
-static int enable_switch_port(struct phy_device *pdev, int port, bool enable)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-	u16 reg;
-
-	/* power up port */
-	dev_info(&priv->client->dev, "Port%d: %s\n", port,
-		 enable ? "normal operation" : "power down");
-	reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL);
-	if (enable)
-		reg &= ~(1 << 11);	/* Normal Operation */
-	else
-		reg |= (1 << 11);	/* power down */
-	write_switch_port_phy(pdev, port, MV_PHY_CONTROL, reg);
-
-	reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL1);
-	if (enable)
-		reg &= ~(1 << 2);	/* Normal Operation */
-	else
-		reg |= (1 << 2);	/* power down */
-	write_switch_port_phy(pdev, port, MV_PHY_CONTROL1, reg);
-
-	return 0;
-}
-#endif
-
-/*
- * Sysfs API
- */
-
-struct mv88e1111_port_state *get_port_state(struct mv88e1111_priv *priv,
-					    int port)
-{
-	if (port == 5)
-		return &priv->port5;
-	if (port == 6)
-		return &priv->port6;
-	return NULL;
-}
-
-/*
- * get MV88E6176 port number for a specific GW16083 port name
- *  The GW16083 ports as shown on the silkscreen are not mapped according to
- *  the MV88E6176 ports numbers.
- */
-static int gw16083_get_port(const char* name)
-{
-	int i;
-	int map[] = { 3, 2, 1, 0, 5, 6 };
-
-	if (strncasecmp(name, "LAN", 3) != 0)
-		return -1;
-	i = name[3] - '0';
-	if (i < 1 || i > 6)
-		return -1;
-	return map[i-1];
-}
-
-#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
-static ssize_t port_show(struct device *dev, struct device_attribute *attr,
-			 char *buf)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	int port = -1;
-	u16 reg;
-
-	if (sscanf(attr->attr.name, "port%d", &port) != 1)
-		return 0;
-	if (port < 0 || port > 6)
-		return 0;
-	reg = read_switch_port_phy(priv->phydev, port, MV_PHY_CONTROL);
-	return sprintf(buf, "%s\n", (reg & (1 << 11)) ? "disabled" : "enabled");
-}
-
-#if defined(PORT_POWER_CONTROL)
-static ssize_t port_store(struct device *dev, struct device_attribute *attr,
-			  const char *buf, size_t count)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	int port = -1;
-	int val;
-
-	port = gw16083_get_port(attr->attr.name);
-	if (port < 0)
-		return 0;
-	if (sscanf(buf, "%d", &val) != 1)
-		return 0;
-	enable_switch_port(priv->phydev, port, val ? 1 : 0);
-	return count;
-}
-
-static DEVICE_ATTR(lan1, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(lan2, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(lan3, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(lan4, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(lan5, S_IWUSR | S_IRUGO, port_show, port_store);
-static DEVICE_ATTR(lan6, S_IWUSR | S_IRUGO, port_show, port_store);
-#else
-static DEVICE_ATTR(lan1, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(lan2, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(lan3, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(lan4, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(lan5, S_IRUGO, port_show, NULL);
-static DEVICE_ATTR(lan6, S_IRUGO, port_show, NULL);
-#endif
-#endif /* #if IS_ENABLED(CONFIG_NET_DSA_MV88E6352) */
-
-static ssize_t portmode_show(struct device *dev, struct device_attribute *attr,
-			     char *buf)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	struct mv88e1111_port_state *state;
-
-	state = get_port_state(priv, gw16083_get_port(attr->attr.name));
-	if (!state)
-		return 0;
-
-	return sprintf(buf, "%s\n", state->serdes ? "SFP" : "RJ45");
-}
-#ifdef PORT_MODE_CONTROL
-static ssize_t portmode_store(struct device *dev, struct device_attribute *attr,
-			      const char *buf, size_t count)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	struct mv88e1111_port_state *state;
-	u16 reg;
-	int port;
-
-	port = gw16083_get_port(attr->attr.name);
-	state = get_port_state(priv, port);
-	if (!state)
-		return 0;
-
-	reg = read_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR);
-	if (strcasecmp(buf, "auto") == 0) {
-		reg &= ~(1<<15); /* enable auto-selection */
-		dev_info(&priv->client->dev, "Port%d: enable auto-selection\n",
-			 port);
-	} else if (strcasecmp(buf, "RJ45") == 0) {
-		reg |= (1<<15); /* disable auto-selection */
-		reg |= 0xb; /* RGMII to Copper */
-		config_mv88e1111_port_sfp(priv->phydev, port, 0);
-		dev_info(&priv->client->dev, "Port%d: select RJ45\n", port);
-	} else if (strcasecmp(buf, "SFP") == 0) {
-		reg |= (1<<15); /* disable auto-selection */
-		reg |= 0x3; /* RGMII to Fiber */
-		config_mv88e1111_port_sfp(priv->phydev, port, 1);
-		dev_info(&priv->client->dev, "Port%d: select SFP\n", port);
-	}
-	write_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR, reg);
-
-	return count;
-}
-
-static DEVICE_ATTR(lan5_mode, S_IWUSR | S_IRUGO, portmode_show, portmode_store);
-static DEVICE_ATTR(lan6_mode, S_IWUSR | S_IRUGO, portmode_show, portmode_store);
-#else
-static DEVICE_ATTR(lan5_mode, S_IRUGO, portmode_show, NULL);
-static DEVICE_ATTR(lan6_mode, S_IRUGO, portmode_show, NULL);
-#endif
-
-static ssize_t portsfp_show(struct device *dev, struct device_attribute *attr,
-			     char *buf)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
-	struct mv88e1111_port_state *state;
-
-	state = get_port_state(priv, gw16083_get_port(attr->attr.name));
-	if (!state)
-		return 0;
-
-	if (!state->sfp_present)
-		return 0;
-
-	return sprintf(buf, "%s\n", state->sfp_id);
-}
-
-static DEVICE_ATTR(lan5_sfp, S_IRUGO, portsfp_show, NULL);
-static DEVICE_ATTR(lan6_sfp, S_IRUGO, portsfp_show, NULL);
-
-/*
- * PHY driver
- */
-
-/* check MV88E1111 PHY status and MV88E6176 GPIO */
-static void
-mv88e6176_work(struct work_struct *work)
-{
-	struct mv88e1111_priv *priv =
-		container_of(work, struct mv88e1111_priv, work.work);
-	struct phy_device *pdev = priv->phydev;
-	struct device *dev = &priv->client->dev;
-	struct mv88e1111_port_state *state;
-	bool serdes, sfp_present, sfp_signal;
-	int port;
-	u16 gpio;
-
-	mutex_lock(&pdev->lock);
-	gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
-	for (port = 5; port < 7; port++) {
-		serdes = (read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_SR)
-			 & (1<<13)) ? 1 : 0;
-		dev_dbg(dev, "%s: Port%d GPIO:0x%02x SerDes:%d\n",
-			__func__, port, gpio, serdes);
-		switch(port) {
-		case 5:
-			state = &priv->port5;
-			sfp_present = !((gpio >> 5) & 1);
-			sfp_signal = !((gpio >> 6) & 1);
-			break;
-		case 6:
-			state = &priv->port6;
-			sfp_present = !((gpio >> 3) & 1);
-			sfp_signal = !((gpio >> 4) & 1);
-			break;
-		}
-
-		/*
-		 * on sfp_detect read/verify SFP MSA and set sfp_compat
-		 * on sfp_signal issue link down?
-		 * on serdes auto-select
-		 */
-		if (state->sfp_present != sfp_present) {
-			state->sfp_present = sfp_present;
-			dev_info(dev, "Port%d: SFP %s\n",
-				 port, sfp_present ? "inserted" : "removed");
-			if (state->sfp_present) {
-				if (gw16083_read_port_sfp(priv->client, state))
-					state->sfp_compat = false;
-				else
-					state->sfp_compat = true;
-				/* trigger a re-select/enable below */
-				state->serdes = !serdes;
-				pdev->state = PHY_RUNNING;
-			} else {
-				state->sfp_compat = false;
-				state->sfp_enabled = false;
-				pdev->state = PHY_NOLINK;
-			}
-		}
-		if (state->sfp_signal != sfp_signal) {
-			state->sfp_signal = sfp_signal;
-			dev_info(dev, "Port%d: SFP signal %s\n",
-				 port, sfp_signal ? "detected" : "lost");
-		}
-		if (state->serdes != serdes) {
-			state->serdes = serdes;
-			dev_info(dev, "Port%d: %s auto-selected\n",
-				 port, serdes ? "SERDES" : "copper");
-
-			/*
-			 * if auto-selection has switched to copper
-			 * disable serdes
-			 */
-			if (!serdes) {
-				config_mv88e1111_port_sfp(pdev, port, 0);
-				state->sfp_enabled = false;
-			}
-		}
-
-		/* if compatible SFP module and not yet enabled then enable */
-		if (state->sfp_compat && state->sfp_signal &&
-		    !state->sfp_enabled)
-		{
-			if (!config_mv88e1111_port_sfp(pdev, port, 1))
-				state->sfp_enabled = true;
-		}
-	}
-	mutex_unlock(&pdev->lock);
-
-	queue_delayed_work(priv->workq, &priv->work, HZ);
-}
-
-static int
-mv88e6176_read_status(struct phy_device *pdev)
-{
-	return 0;
-}
-
-static int
-mv88e6176_config_aneg(struct phy_device *pdev)
-{
-	return 0;
-}
-
-static int
-mv88e6176_config_init(struct phy_device *pdev)
-{
-	pdev->state = PHY_RUNNING;
-
-	return 0;
-}
-
-static void
-mv88e6176_remove(struct phy_device *pdev)
-{
-	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
-
-	dev_dbg(&priv->client->dev, "%s", __func__);
-
-	destroy_workqueue(priv->workq);
-#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
-	device_remove_file(&pdev->dev, &dev_attr_lan1);
-	device_remove_file(&pdev->dev, &dev_attr_lan2);
-	device_remove_file(&pdev->dev, &dev_attr_lan3);
-	device_remove_file(&pdev->dev, &dev_attr_lan4);
-	device_remove_file(&pdev->dev, &dev_attr_lan5);
-	device_remove_file(&pdev->dev, &dev_attr_lan6);
-#endif
-	device_remove_file(&pdev->dev, &dev_attr_lan5_sfp);
-	device_remove_file(&pdev->dev, &dev_attr_lan6_sfp);
-	device_remove_file(&pdev->dev, &dev_attr_lan5_mode);
-	device_remove_file(&pdev->dev, &dev_attr_lan6_mode);
-	sysfs_remove_link(kernel_kobj, "gw16083");
-}
-
-/*
- * mv88e6176_probe - called any time an MV88E6176 is found on an mdio bus
- *  Determine if this MV88E6176 is indeed on a GW16083 and if so configure
- *  the port5/port6 phy and register a background procedure for monitoring
- *  their states to support SFP vs Copper switching.
- *
- * Verify this is a GW16083 by ensuring:
- *   - the phy address matches that of a GW16083
- *   - the mdio bus is from an i210 device (igb driver)
- *   - there are MV881111 PHY's hanging off of Port5 and Port6
- */
-static int
-mv88e6176_probe(struct phy_device *pdev)
-{
-	int port;
-	int ret = 0;
-	u32 id, reg;
-	struct mv88e1111_priv *priv;
-	struct device *dev;
-#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
-	struct net_device *netdev = NULL;
-#endif
-
-	dev_dbg(&pdev->dev, "%s: addr=0x%02x bus=%s:%s gw16083_client=%p\n",
-		__func__, pdev->addr, pdev->bus->name, pdev->bus->id,
-		gw16083_client);
-
-	/* In single-chip addressing mode the MV88E6176 shows up on 0x10-0x16 */
-	if (pdev->addr != MV_BASE)
-		return 0;
-
-	/* i2c driver needs to be loaded first */
-	if (!gw16083_client)
-		return 0;
-	dev = &gw16083_client->dev;
-
-	/* gw16083 has MV88E1676 hanging off of i210 mdio bus */
-	if (strcmp(pdev->bus->name, "igb_enet_mii_bus") != 0)
-		return 0;
-
-	/* verify Port5/Port6 have an MV88E1111 PHY hanging off them */
-	for (port = 5; port < 7; port++) {
-		id = read_switch_port_phy(pdev, port,
-					  MII_M1111_PHY_IDENT0) << 16;
-		id |= read_switch_port_phy(pdev, port, MII_M1111_PHY_IDENT1);
-		if ((id & MII_M1111_PHY_ID_MASK) != MII_M1111_PHY_ID) {
-			dev_err(dev, "Port%d: No MV88E1111 PHY detected", port);
-			return 0;
-		}
-	}
-
-#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
-	/*
-	 * Find the netdev this bus is hanging off of and register with DSA:
-	 *  The netdev must be an Intel I210 (igb) with Gateworks MAC addr
-	 */
-	read_lock(&dev_base_lock);
-	for_each_netdev(&init_net, netdev) {
-		if (netdev->dev.parent &&
-		    !strcmp(netdev->dev.parent->driver->name, "igb") &&
-		    (netdev->perm_addr[0] == 0x00) &&
-		    (netdev->perm_addr[1] == 0xd0) &&
-		    (netdev->perm_addr[2] == 0x12))
-		{
-			switch_plat_data.netdev = &netdev->dev;
-			switch_plat_data.chip[0].host_dev = &pdev->bus->dev;
-			break;
-		}
-	}
-	read_unlock(&dev_base_lock);
-
-	if (switch_plat_data.netdev) {
-		platform_device_register(&switch_device);
-		dev_info(dev, "registered GW16083 DSA switch\n");
-	} else {
-		dev_err(dev, "failed to find netdev for DSA switch\n");
-	}
-#endif
-
-	/*
-	 * port5/6 config: MV88E1111 PHY
-	 * Register 20: PHY Control Register
-	 *   R20_7: add delay to RX_CLK for RXD
-	 *   R20_1: add delay to TX_CLK for TXD
-	 * Register 24: LED Control Register
-	 *   0x4111:
-	 *     Pulse stretch 170 to 340 ms
-	 * Register 0: Control Register
-	 *   R0_15: phy reset
-	 */
-	dev_info(dev, "Configuring MV88E6176 7-port switch");
-	for (port = 5; port < 7; port++) {
-#ifdef RGMII_DELAY_ON_PHY
-		/* phy rx/tx delay */
-		reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR);
-		reg |= (1<<1) | (1<<7);
-		write_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR, reg);
-#else
-		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, 0xC003);
-#endif
-
-		/* led config */
-		write_switch_port_phy(pdev, port, MII_M1111_PHY_LED_CONTROL,
-				      MII_M1111_PHY_LED_PULSE_STR);
-		/* reset phy */
-		reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL);
-		reg |= MII_M1111_PHY_CONTROL_RESET;
-		write_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL, reg);
-		dev_info(dev, "Port%d: MV88E111 PHY configured\n", port);
-	}
-
-	/*
-	 * GPIO Configuration:
-	 *  GPIO1: FIB5_TXEN# (output)
-	 *  GPIO2: FIB6_TXEN# (output)
-	 *  GPIO3: FIB6_PRES# (input)
-	 *  GPIO4: FIB6_LOS   (input)
-	 *  GPIO5: FIB5_PRES# (input)
-	 *  GPIO6: FIB5_LOS   (input)
-	 */
-	write_switch_scratch(pdev, MV_GPIO_DATA, 0x06); /* GPIO[2:1] out hi */
-	write_switch_scratch(pdev, MV_GPIO_DIR,  0x78); /* GPIO[6:3] inp */
-
-	pdev->irq = PHY_POLL;
-
-	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-	memset(priv, 0, sizeof(*priv));
-	priv->phydev = pdev;
-	priv->client = gw16083_client;
-	priv->port5.port = 5;
-	priv->port6.port = 6;
-	dev_set_drvdata(&pdev->dev, priv);
-
-	/* register sysfs API */
-#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan1);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan2);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan3);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan4);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan5);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan6);
-#endif
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan5_sfp);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan6_sfp);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan5_mode);
-	ret |= device_create_file(&pdev->dev, &dev_attr_lan6_mode);
-
-	if (unlikely(ret))
-		dev_err(&pdev->dev, "Failed creating attrs\n");
-
-	/* Add a nice symlink to the real device */
-	ret = sysfs_create_link(kernel_kobj, &pdev->dev.kobj, "gw16083");
-
-	INIT_DELAYED_WORK(&priv->work, mv88e6176_work);
-	priv->workq = create_singlethread_workqueue("gw16083");
-	if (!priv->workq)
-		return -ENODEV;
-	queue_delayed_work(priv->workq, &priv->work, 0);
-
-	dev_dbg(dev, "initial state: GPIO=0x%02x "
-		"Port5_serdes=%d Port6_serdes=%d\n",
-		read_switch_scratch(pdev, MV_GPIO_DATA),
-		(read_switch_port_phy(pdev, 5, MII_M1111_PHY_EXT_SR)
-		 & (1<<13) ? 1:0),
-		(read_switch_port_phy(pdev, 6, MII_M1111_PHY_EXT_SR)
-		 & (1<<13) ? 1:0));
-
-	return ret;
-}
-
-static struct phy_driver mv88e6176_phy_driver = {
-	.name		= "gw16083",
-	.phy_id		= MV_IDENT_VALUE,
-	.phy_id_mask	= MV_IDENT_MASK,
-	.features	= PHY_BASIC_FEATURES,
-	.probe		= &mv88e6176_probe,
-	.remove		= &mv88e6176_remove,
-	.config_init	= &mv88e6176_config_init,
-	.config_aneg	= &mv88e6176_config_aneg,
-	.read_status	= &mv88e6176_read_status,
-	.driver		= { .owner = THIS_MODULE },
-};
-
-/*
- * I2C driver
- */
-
-/* See SFF-8472 */
-struct sfp_msa {
-	/* Basic ID fields */
-	u8	identifier;
-	u8	ext_identifier;
-	u8	connector;
-	u8	transceiver[8];
-	u8	encoding;
-	u8	br_nominal;
-	u8	rate_identifier;
-	u8	length_smf_km;
-	u8	length_smf;
-	u8	length_om2;
-	u8	length_om1;
-	u8	length_om4;
-	u8	length_om3;
-	u8	vendor_name[16];
-	u8	transceiver2;
-	u8	vendor_oui[3];
-	u8	vendor_pn[16];
-	u8	vendor_rev[4];
-	u8	wavelength[2];
-	u8	resv1;
-	u8	cc_base;
-
-	/* extended id fields */
-	u8	options[2];
-	u8	br_max;
-	u8	br_min;
-	u8	vendor_sn[16];
-	u8	date_code[8];
-	u8	diags_type;
-	u8	enhanced_options;
-	u8	sff8472_compliance;
-	u8	cc_ext;
-
-	/* Vendor specific ID fields */
-	u8	vendor_data[32];
-	u8	sff8079[128];
-};
-
-enum identifier {
-	UNKNOWN,
-	GBIC,
-	SFF,
-	SFP,
-	XBI,
-	XENPACK,
-	XFP,
-	XFF,
-	XFP_E,
-	XPAK,
-	X2,
-	DWDM_SFP,
-	QSFP,
-	MAX_ID,
-};
-
-const char* id_names[] = {
-	"UNKONWN",
-	"GBIC",
-	"SFF",
-	"SFP",
-	NULL,
-};
-
-/* Flags for SFP modules compatible with ETH up to 1Gb */
-struct sfp_flags {
-	u8 e1000_base_sx:1;
-	u8 e1000_base_lx:1;
-	u8 e1000_base_cx:1;
-	u8 e1000_base_t:1;
-	u8 e100_base_lx:1;
-	u8 e100_base_fx:1;
-	u8 e10_base_bx10:1;
-	u8 e10_base_px:1;
-};
-
-#define STRING_APPEND(str, src)				\
-	strncat(str, src, sizeof(src));			\
-	for (i = 1; i < sizeof(str); i++)		\
-		if (str[i-1] == ' ' && str[i] == ' ')	\
-			str[i] = 0;
-
-static int gw16083_read_port_sfp(struct i2c_client *client,
-				 struct mv88e1111_port_state *state)
-{
-	int ret = 0;
-	u8 data[256];
-	struct sfp_flags *eth_flags;
-	u8 crc;
-	int i;
-	u8 *str;
-	struct sfp_msa *sfp_msa = (struct sfp_msa *)data;
-	int port = state->port;
-	union i2c_smbus_data d;
-
-	dev_dbg(&client->dev, "%s Port%d\n", __func__, port);
-	if (!i2c_check_functionality(client->adapter,
-				     I2C_FUNC_SMBUS_READ_I2C_BLOCK))
-		return -ENODEV;
-	d.byte = (port == 5) ? 1 : 2;
-	if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_PCA9543,
-			   client->flags, I2C_SMBUS_WRITE, 0,
-			   I2C_SMBUS_BYTE_DATA, &d) < 0)
-	{
-		dev_err(&client->dev,
-			"Port%d: failed writing PCA9543 register\n", port);
-		return ret;
-	}
-
-	/* read all 256 bytes of SFP EEPROM */
-	for (i = 0; i < sizeof(data); i += I2C_SMBUS_BLOCK_MAX) {
-		d.block[0] = I2C_SMBUS_BLOCK_MAX;
-		if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_SFP1,
-				   client->flags, I2C_SMBUS_READ, i,
-				   I2C_SMBUS_I2C_BLOCK_DATA, &d) < 0)
-		{
-			dev_err(&client->dev,
-				"Port%d: failed reading SFP data\n", port);
-			return ret;
-		}
-		memcpy(data + i, d.block + 1, I2C_SMBUS_BLOCK_MAX);
-	}
-
-	/* Validate checksums */
-	for (crc = 0, i = 0; i < 63; i++)
-		crc += data[i];
-	if (crc != sfp_msa->cc_base) {
-		dev_err(&client->dev, "Port%d: "
-			"Checksum failure for Base ID fields: 0x%02x\n", port,
-			crc);
-#ifdef FAIL_ON_CHECKSUM_ERR
-		return -EINVAL;
-#endif
-	}
-	for (crc = 0, i = 64; i < 95; i++)
-		crc += data[i];
-	if (crc != sfp_msa->cc_ext) {
-		dev_err(&client->dev, "Port%d: "
-			"Checksum failure for Extended ID fields: 0x%02x\n",
-			port, crc);
-#ifdef FAIL_ON_CHECKSUM_ERR
-		return -EINVAL;
-#endif
-	}
-	state->sfp_id[0] = 0;
-	for (i = 0; id_names[i]; i++) {
-		if (sfp_msa->identifier == i) {
-			sprintf(state->sfp_id, "%s: ", id_names[i]);
-			break;
-		}
-	}
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_oui);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_name);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_pn);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_rev);
-	STRING_APPEND(state->sfp_id, sfp_msa->vendor_sn);
-	dev_info(&client->dev, "Port%d: %s\n", port, state->sfp_id);
-
-	if ((sfp_msa->identifier != GBIC) &&
-	    (sfp_msa->identifier != SFF) &&
-	    (sfp_msa->identifier != SFP))
-	{
-		dev_err(&client->dev, "Port%d: Unknown module identifier: %d\n",
-			port, sfp_msa->identifier);
-		return -EINVAL;
-	}
-
-	str = "";
-	eth_flags = (struct sfp_flags *)(sfp_msa->transceiver + 3);
-	if (eth_flags->e1000_base_sx) {
-		str = "1000Base-SX (Fiber)";
-	} else if (eth_flags->e1000_base_lx) {
-		str = "1000Base-LX (Fiber)";
-	} else if (eth_flags->e1000_base_t) {
-		str = "1000Base-T (Copper)";
-	} else if (eth_flags->e100_base_fx) {
-		str = "100Base-FX (Fiber) - not supported";
-		ret = -EINVAL;
-	} else {
-		str = "Unknown/Unsupported media type";
-		ret = -EINVAL;
-	}
-	if (ret)
-		dev_err(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
-			sfp_msa->transceiver[3]);
-	else
-		dev_info(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
-			sfp_msa->transceiver[3]);
-
-	return ret;
-}
-
-static int gw16083_probe(struct i2c_client *client,
-			 const struct i2c_device_id *id)
-{
-	int ret;
-
-	dev_info(&client->dev, "GW16083 Ethernet Expansion Mezzanine\n");
-	if (gw16083_client) {
-		dev_err(&client->dev, "client already registered\n");
-		return -EINVAL;
-	}
-	gw16083_client = client;
-
-	ret = phy_driver_register(&mv88e6176_phy_driver);
-	if (ret)
-		dev_err(&client->dev,
-			"failed to register mv88e6176 phy driver: %d\n", ret);
-	return ret;
-}
-
-static int gw16083_remove(struct i2c_client *client)
-{
-	dev_dbg(&client->dev, "%s\n", __func__);
-
-	phy_driver_unregister(&mv88e6176_phy_driver);
-	gw16083_client = NULL;
-	return 0;
-}
-
-static const struct of_device_id gw16083_dt_ids[] = {
-	{ .compatible = "gateworks,gw16083", },
-	{ }
-};
-
-MODULE_DEVICE_TABLE(of, gw16083_dt_ids);
-
-static const struct i2c_device_id gw16083_id[] = {
-	{ "gw16083", 0 },
-	{ }
-};
-MODULE_DEVICE_TABLE(i2c, gw16083_id);
-
-static struct i2c_driver gw16083_driver = {
-	.driver = {
-		.name	= "gw16083",
-		.of_match_table = gw16083_dt_ids,
-	},
-	.probe		= gw16083_probe,
-	.remove		= gw16083_remove,
-	.id_table	= gw16083_id,
-};
-
-static int __init mv88e6176_init(void)
-{
-	return i2c_add_driver(&gw16083_driver);
-}
-
-static void __exit mv88e6176_exit(void)
-{
-	i2c_del_driver(&gw16083_driver);
-}
-
-module_init(mv88e6176_init);
-module_exit(mv88e6176_exit);

target/linux/imx6/files-4.4/drivers/net/phy/gw16083.h

@@ -1,123 +0,0 @@
-/*
- * drivers/net/phy/mv88e6176.h
- *
- * Driver for Marvell Switch
- *
- * Author: Tim Harvey
- *
- * Copyright (c) 2014 Tim Harvey <[email protected]>
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-#ifndef _GW16083_H_
-#define _GW16083_H_
-
-#define MII_MARVELL_PHY_PAGE		22
-
-/*
- * I2C Addresses
- */
-#define GW16083_I2C_ADDR_SFP1		0x50
-#define GW16083_I2C_ADDR_SFP2		0x51
-#define GW16083_I2C_ADDR_EEPROM		0x52
-#define GW16083_I2C_ADDR_PCA9543	0x70
-
-/*
- * MV88E1111 PHY Registers
- */
-enum {
-	MII_M1111_PHY_CONTROL		= 0,
-	MII_M1111_PHY_STATUS 		= 1,
-	MII_M1111_PHY_IDENT0		= 2,
-	MII_M1111_PHY_IDENT1		= 3,
-	MII_M1111_PHY_EXT_CR		= 20,
-	MII_M1111_PHY_LED_CONTROL	= 24,
-	MII_M1111_PHY_EXT_SR		= 27,
-};
-
-#define MII_M1111_PHY_ID_MASK		0xfffffff0
-#define MII_M1111_PHY_ID		0x01410cc0
-
-#define MII_M1111_PHY_CONTROL_RESET	(1 << 15)
-#define MII_M1111_PHY_LED_DIRECT	0x4100
-#define MII_M1111_PHY_LED_PULSE_STR	0x4111
-#define MII_M1111_PHY_LED_COMBINE	0x411c
-#define MII_M1111_RX_DELAY		0x80
-#define MII_M1111_TX_DELAY		0x2
-
-/*
- * MV88E6176 Switch Registers
- */
-
-/* PHY Addrs */
-#define MV_BASE		0x10
-#define MV_GLOBAL1	0x1b
-#define MV_GLOBAL2	0x1c
-#define MV_GLOBAL3	0x1d
-
-/* Global2 Registers */
-enum {
-	MV_SMI_PHY_COMMAND	= 0x18,
-	MV_SMI_PHY_DATA		= 0x19,
-	MV_SCRATCH_MISC		= 0x1A,
-};
-
-/* Scratch And Misc Reg offsets */
-enum {
-	MV_GPIO_MODE		= 0x60,
-	MV_GPIO_DIR		= 0x62,
-	MV_GPIO_DATA		= 0x64,
-	MV_GPIO76_CNTL		= 0x6B,
-	MV_GPIO54_CNTL		= 0x6A,
-	MV_GPIO32_CNTL		= 0x69,
-	MV_GPIO10_CNTL		= 0x68,
-	MV_CONFIG0		= 0x70,
-	MV_CONFIG1		= 0x71,
-	MV_CONFIG2		= 0x72,
-	MV_CONFIG3		= 0x73,
-};
-
-/* PHY Registers */
-enum {
-	MV_PHY_CONTROL      = 0x00,
-	MV_PHY_STATUS       = 0x01,
-	MV_PHY_IDENT0       = 0x02,
-	MV_PHY_IDENT1       = 0x03,
-	MV_PHY_ANEG         = 0x04,
-	MV_PHY_LINK_ABILITY = 0x05,
-	MV_PHY_ANEG_EXPAND  = 0x06,
-	MV_PHY_XMIT_NEXTP   = 0x07,
-	MV_PHY_LINK_NEXTP   = 0x08,
-	MV_PHY_CONTROL1     = 0x10,
-	MV_PHY_STATUS1      = 0x11,
-	MV_PHY_INTR_EN      = 0x12,
-};
-
-/* Port Registers */
-enum {
-	MV_PORT_STATUS      	= 0x00,
-	MV_PORT_PHYS_CONTROL	= 0x01,
-	MV_PORT_IDENT       	= 0x03,
-	MV_PORT_CONTROL     	= 0x04,
-	MV_PORT_VLANMAP     	= 0x06,
-	MV_PORT_ASSOC       	= 0x0b,
-	MV_PORT_RXCOUNT     	= 0x10,
-	MV_PORT_TXCOUNT     	= 0x11,
-};
-
-#define SMIBUSY		(1<<15)
-#define SMIMODE22	(1<<12)
-#define SMIOP_READ	(2<<10)
-#define SMIOP_WRITE	(1<<10)
-#define DEVADDR		5
-#define REGADDR		0
-
-#define MV_IDENT_MASK		0x0000fff0
-#define MV_IDENT_VALUE		0x00001760
-
-#endif /* _GW16083_H_ */

target/linux/imx6/patches-4.4/0005-ARM-dts-imx-add-gw553x-support.patch

@@ -1,18 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -293,6 +293,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
- 	imx6dl-gw54xx.dtb \
- 	imx6dl-gw551x.dtb \
- 	imx6dl-gw552x.dtb \
-+	imx6dl-gw553x.dtb \
- 	imx6dl-hummingboard.dtb \
- 	imx6dl-nit6xlite.dtb \
- 	imx6dl-nitrogen6x.dtb \
-@@ -322,6 +323,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
- 	imx6q-gw54xx.dtb \
- 	imx6q-gw551x.dtb \
- 	imx6q-gw552x.dtb \
-+	imx6q-gw553x.dtb \
- 	imx6q-hummingboard.dtb \
- 	imx6q-nitrogen6x.dtb \
- 	imx6q-nitrogen6_max.dtb \

target/linux/imx6/patches-4.4/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch

@@ -1,26 +0,0 @@
-From 57b82d9e79d77442bae3d2c13b98ceccb39fe5e2 Mon Sep 17 00:00:00 2001
-From: Tim Harvey <[email protected]>
-Date: Thu, 5 Nov 2015 10:49:31 -0800
-Subject: [PATCH 1/3] ARM: dts: imx: ventana: set GW54xx PMIC swbst regulator
- as always-on
-
-The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
-and HDMI DDC and is enabled by the bootloader. Set the regulator to
-always-on so that Linux doesn't turn it off thinking its not needed.
-
-Signed-off-by: Tim Harvey <[email protected]>
----
- arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-@@ -260,6 +260,8 @@
- 			swbst_reg: swbst {
- 				regulator-min-microvolt = <5000000>;
- 				regulator-max-microvolt = <5150000>;
-+				regulator-boot-on;
-+				regulator-always-on;
- 			};
- 
- 			snvs_reg: vsnvs {

target/linux/imx6/patches-4.4/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch

@@ -1,33 +0,0 @@
-From 473d0353979db3673a7aa365265ba9b00decd414 Mon Sep 17 00:00:00 2001
-From: Tim Harvey <[email protected]>
-Date: Thu, 5 Nov 2015 10:52:53 -0800
-Subject: [PATCH 2/3] ARM: dts: imx: ventana: fix GW53xx/GW54xx lvds channel
-
-Signed-off-by: Tim Harvey <[email protected]>
----
- arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 +-
- arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-@@ -247,7 +247,7 @@
- &ldb {
- 	status = "okay";
- 
--	lvds-channel@1 {
-+	lvds-channel@0 {
- 		fsl,data-mapping = "spwg";
- 		fsl,data-width = <18>;
- 		status = "okay";
---- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-@@ -338,7 +338,7 @@
- &ldb {
- 	status = "okay";
- 
--	lvds-channel@1 {
-+	lvds-channel@0 {
- 		fsl,data-mapping = "spwg";
- 		fsl,data-width = <18>;
- 		status = "okay";

target/linux/imx6/patches-4.4/037-ARM-dts-imx-ventana-Allow-HDMI-and-LVDS-to-work-simultaneously.patch

@@ -1,70 +0,0 @@
-From d86b202436b6f3111c4c37b8701daa0764d2ca55 Mon Sep 17 00:00:00 2001
-From: Tim Harvey <[email protected]>
-Date: Thu, 5 Nov 2015 11:10:00 -0800
-Subject: [PATCH 3/3] ARM: dts: imx: ventana: Allow HDMI and LVDS to work
- simultaneously
-
-Currently it is not possible to have HDMI and LVDS working simultaneously,
-because both ports try to use PLL5.
-
-Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
-driven from independent sources.
-
-With this change the LDB pixel clock goes to 68.57 MHz, which is still
-within the valid range for the displays supported by the Ventana boards.
-
-Signed-off-by: Tim Harvey <[email protected]>
----
- arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 7 +++++++
- arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 7 +++++++
- arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 7 +++++++
- 3 files changed, 21 insertions(+)
-
---- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-@@ -151,6 +151,13 @@
- 	status = "okay";
- };
- 
-+&clks {
-+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-+	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-+};
-+
- &fec {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_enet>;
---- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-@@ -152,6 +152,13 @@
- 	status = "okay";
- };
- 
-+&clks {
-+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-+	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-+};
-+
- &fec {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_enet>;
---- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-@@ -142,6 +142,13 @@
- 	status = "okay";
- };
- 
-+&clks {
-+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-+	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-+	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-+};
-+
- &fec {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_enet>;

target/linux/imx6/patches-4.4/040-ARM-dts-imx-ventana-add-pwm-nodes.patch

@@ -1,264 +0,0 @@
---- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
-@@ -174,6 +174,24 @@
- 	status = "okay";
- };
- 
-+&pwm2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-+	status = "disabled";
-+};
-+
-+&pwm3 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-+	status = "disabled";
-+};
-+
-+&pwm4 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
-+	status = "disabled";
-+};
-+
- &uart1 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_uart1>;
-@@ -294,6 +312,24 @@
- 			>;
- 		};
- 
-+		pinctrl_pwm2: pwm2grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm3: pwm3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm4: pwm4grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
-+			>;
-+		};
-+
- 		pinctrl_uart1: uart1grp {
- 			fsl,pins = <
- 				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
---- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-@@ -282,6 +282,18 @@
- 	status = "okay";
- };
- 
-+&pwm2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-+	status = "disabled";
-+};
-+
-+&pwm3 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-+	status = "disabled";
-+};
-+
- &pwm4 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_pwm4>;
-@@ -436,6 +448,18 @@
- 			>;
- 		};
- 
-+		pinctrl_pwm2: pwm2grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm3: pwm3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+			>;
-+		};
-+
- 		pinctrl_pwm4: pwm4grp {
- 			fsl,pins = <
- 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
---- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-@@ -287,6 +287,18 @@
- 	};
- };
- 
-+&pwm2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-+	status = "disabled";
-+};
-+
-+&pwm3 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-+	status = "disabled";
-+};
-+
- &pwm4 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_pwm4>;
-@@ -442,6 +454,18 @@
- 			>;
- 		};
- 
-+		pinctrl_pwm2: pwm2grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm3: pwm3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+			>;
-+		};
-+
- 		pinctrl_pwm4: pwm4grp {
- 			fsl,pins = <
- 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
---- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-@@ -378,6 +378,24 @@
- 	};
- };
- 
-+&pwm1 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm1>; /* MX6_DIO0 */
-+	status = "disabled";
-+};
-+
-+&pwm2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-+	status = "disabled";
-+};
-+
-+&pwm3 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-+	status = "disabled";
-+};
-+
- &pwm4 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_pwm4>;
-@@ -537,6 +555,24 @@
- 			>;
- 		};
- 
-+		pinctrl_pwm1: pwm1grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_GPIO_9__PWM1_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm2: pwm2grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm3: pwm3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+			>;
-+		};
-+
- 		pinctrl_pwm4: pwm4grp {
- 			fsl,pins = <
- 				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
---- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
-@@ -198,6 +198,18 @@
- 	status = "okay";
- };
- 
-+&pwm2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-+	status = "disabled";
-+};
-+
-+&pwm3 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-+	status = "disabled";
-+};
-+
- &ssi1 {
- 	status = "okay";
- };
-@@ -290,6 +302,18 @@
- 			>;
- 		};
- 
-+		pinctrl_pwm2: pwm2grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm3: pwm3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
-+			>;
-+		};
-+
- 		pinctrl_uart2: uart2grp {
- 			fsl,pins = <
- 				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
---- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
-@@ -164,6 +164,18 @@
- 	status = "okay";
- };
- 
-+&pwm2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
-+	status = "disabled";
-+};
-+
-+&pwm3 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
-+	status = "disabled";
-+};
-+
- &uart2 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_uart2>;
-@@ -242,6 +254,18 @@
- 			>;
- 		};
- 
-+		pinctrl_pwm2: pwm2grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT		0x1b0b1
-+			>;
-+		};
-+
-+		pinctrl_pwm3: pwm3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+			>;
-+		};
-+
- 		pinctrl_uart2: uart2grp {
- 			fsl,pins = <
- 				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1

target/linux/imx6/patches-4.4/041-ARM-dts-imx-ventana-add-spi-support-for-gw52xx.patch

@@ -1,33 +0,0 @@
---- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-@@ -158,6 +158,14 @@
- 	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
- };
- 
-+&ecspi3 {
-+	fsl,spi-num-chipselects = <1>;
-+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_ecspi3>;
-+	status = "okay";
-+};
-+
- &fec {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_enet>;
-@@ -357,6 +365,15 @@
- 			>;
- 		};
- 
-+		pinctrl_ecspi3: escpi3grp {
-+			fsl,pins = <
-+				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
-+				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
-+				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
-+				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x100b1
-+			>;
-+		};
-+
- 		pinctrl_enet: enetgrp {
- 			fsl,pins = <
- 				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0

target/linux/imx6/patches-4.4/042-ARM-dts-imx-ventana-fix-PWM-pinmux-for-Ventana-boards.patch

@@ -1,61 +0,0 @@
-commit 3371600cc36d2a6c19cc985660a21c6830f7e7cd
-Author: Tim Harvey <[email protected]>
-Date:   Thu Jan 7 09:03:03 2016 -0800
-
-    ARM: dts: imx: ventana: fix PWM pinmux for Ventana boards
-    
-    Fix some invalid pwm pinmux configurations.
-    
-    Signed-off-by: Tim Harvey <[email protected]>
-
---- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
-@@ -320,13 +320,13 @@
- 
- 		pinctrl_pwm3: pwm3grp {
- 			fsl,pins = <
--				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
- 			>;
- 		};
- 
- 		pinctrl_pwm4: pwm4grp {
- 			fsl,pins = <
--				MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
-+				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
- 			>;
- 		};
- 
---- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-@@ -473,7 +473,7 @@
- 
- 		pinctrl_pwm3: pwm3grp {
- 			fsl,pins = <
--				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
- 			>;
- 		};
- 
---- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-@@ -462,7 +462,7 @@
- 
- 		pinctrl_pwm3: pwm3grp {
- 			fsl,pins = <
--				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
- 			>;
- 		};
- 
---- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
-@@ -262,7 +262,7 @@
- 
- 		pinctrl_pwm3: pwm3grp {
- 			fsl,pins = <
--				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
- 			>;
- 		};
- 

target/linux/imx6/patches-4.4/100-bootargs.patch

@@ -1,11 +0,0 @@
---- a/arch/arm/boot/dts/imx6dl-wandboard.dts
-+++ b/arch/arm/boot/dts/imx6dl-wandboard.dts
-@@ -19,4 +19,8 @@
- 	memory {
- 		reg = <0x10000000 0x40000000>;
- 	};
-+
-+	chosen {
-+		bootargs = "console=ttymxc0,115200";
-+	};
- };

target/linux/imx6/patches-4.4/110-serial-imx-repair-and-complete-handshaking.patch

@@ -1,74 +0,0 @@
-From 90ebc4838666d148eac5bbac6f4044e5b25cd2d6 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= <[email protected]>
-Date: Sun, 18 Oct 2015 21:34:46 +0200
-Subject: [PATCH] serial: imx: repair and complete handshaking
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-The .get_mctrl callback should not report the status of RTS or LOOP, so
-drop this. Instead implement reporting the state of CAR (aka DCD) and
-RI.
-
-For .set_mctrl implement setting the DTR line.
-
-Signed-off-by: Uwe Kleine-König <[email protected]>
-Signed-off-by: Greg Kroah-Hartman <[email protected]>
-Signed-off-by: Petr Štetiar <[email protected]>
----
- drivers/tty/serial/imx.c | 23 +++++++++++++++++------
- 1 file changed, 17 insertions(+), 6 deletions(-)
-
---- a/drivers/tty/serial/imx.c
-+++ b/drivers/tty/serial/imx.c
-@@ -148,8 +148,11 @@
- #define USR2_TXFE	 (1<<14) /* Transmit buffer FIFO empty */
- #define USR2_DTRF	 (1<<13) /* DTR edge interrupt flag */
- #define USR2_IDLE	 (1<<12) /* Idle condition */
-+#define USR2_RIDELT	 (1<<10) /* Ring Interrupt Delta */
-+#define USR2_RIIN	 (1<<9)	 /* Ring Indicator Input */
- #define USR2_IRINT	 (1<<8)	 /* Serial infrared interrupt flag */
- #define USR2_WAKE	 (1<<7)	 /* Wake */
-+#define USR2_DCDIN	 (1<<5)	 /* Data Carrier Detect Input */
- #define USR2_RTSF	 (1<<4)	 /* RTS edge interrupt flag */
- #define USR2_TXDC	 (1<<3)	 /* Transmitter complete */
- #define USR2_BRCD	 (1<<2)	 /* Break condition */
-@@ -804,16 +807,19 @@ static unsigned int imx_tx_empty(struct
- static unsigned int imx_get_mctrl(struct uart_port *port)
- {
- 	struct imx_port *sport = (struct imx_port *)port;
--	unsigned int tmp = TIOCM_DSR | TIOCM_CAR;
-+	unsigned int tmp = TIOCM_DSR;
-+	unsigned usr1 = readl(sport->port.membase + USR1);
- 
--	if (readl(sport->port.membase + USR1) & USR1_RTSS)
-+	if (usr1 & USR1_RTSS)
- 		tmp |= TIOCM_CTS;
- 
--	if (readl(sport->port.membase + UCR2) & UCR2_CTS)
--		tmp |= TIOCM_RTS;
--
--	if (readl(sport->port.membase + uts_reg(sport)) & UTS_LOOP)
--		tmp |= TIOCM_LOOP;
-+	/* in DCE mode DCDIN is always 0 */
-+	if (!(usr1 & USR2_DCDIN))
-+		tmp |= TIOCM_CAR;
-+
-+	/* in DCE mode RIIN is always 0 */
-+	if (readl(sport->port.membase + USR2) & USR2_RIIN)
-+		tmp |= TIOCM_RI;
- 
- 	return tmp;
- }
-@@ -831,6 +837,11 @@ static void imx_set_mctrl(struct uart_po
- 		writel(temp, sport->port.membase + UCR2);
- 	}
- 
-+	temp = readl(sport->port.membase + UCR3) & ~UCR3_DSR;
-+	if (!(mctrl & TIOCM_DTR))
-+		temp |= UCR3_DSR;
-+	writel(temp, sport->port.membase + UCR3);
-+
- 	temp = readl(sport->port.membase + uts_reg(sport)) & ~UTS_LOOP;
- 	if (mctrl & TIOCM_LOOP)
- 		temp |= UTS_LOOP;

target/linux/imx6/patches-4.4/111-serial-imx-fix-polarity-of-RI.patch

@@ -1,33 +0,0 @@
-From 9a061cea4477f26a1dfcc0a08dc20575016e91df Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= <[email protected]>
-Date: Thu, 24 Mar 2016 14:24:20 +0100
-Subject: [PATCH 1/3] serial: imx: fix polarity of RI
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-When in DTE mode, the bit USR2_RIIN is active low. So invert the logic
-accordingly.
-
-Fixes: 90ebc4838666 ("serial: imx: repair and complete handshaking")
-Signed-off-by: Uwe Kleine-König <[email protected]>
-Signed-off-by: Petr Štetiar <[email protected]>
----
- drivers/tty/serial/imx.c | 6 +++---
- 1 file changed, 3 insertions(+), 3 deletions(-)
-
---- a/drivers/tty/serial/imx.c
-+++ b/drivers/tty/serial/imx.c
-@@ -817,9 +817,9 @@ static unsigned int imx_get_mctrl(struct
- 	if (!(usr1 & USR2_DCDIN))
- 		tmp |= TIOCM_CAR;
- 
--	/* in DCE mode RIIN is always 0 */
--	if (readl(sport->port.membase + USR2) & USR2_RIIN)
--		tmp |= TIOCM_RI;
-+	if (sport->dte_mode)
-+		if (!(readl(sport->port.membase + USR2) & USR2_RIIN))
-+			tmp |= TIOCM_RI;
- 
- 	return tmp;
- }

target/linux/imx6/patches-4.4/112-serial-imx-let-irq-handler-return-IRQ_NONE-if-no-eve.patch

@@ -1,67 +0,0 @@
-From de4356da2cd1a1857513047997d81143cb95a4e1 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= <[email protected]>
-Date: Thu, 24 Mar 2016 14:24:21 +0100
-Subject: [PATCH 2/3] serial: imx: let irq handler return IRQ_NONE if no event
- was handled
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This gives the irq core a chance to disable the serial interrupt in case
-an event isn't cleared in the handler.
-
-Signed-off-by: Uwe Kleine-König <[email protected]>
-Signed-off-by: Petr Štetiar <[email protected]>
----
- drivers/tty/serial/imx.c | 17 +++++++++++++----
- 1 file changed, 13 insertions(+), 4 deletions(-)
-
---- a/drivers/tty/serial/imx.c
-+++ b/drivers/tty/serial/imx.c
-@@ -753,6 +753,7 @@ static irqreturn_t imx_int(int irq, void
- 	struct imx_port *sport = dev_id;
- 	unsigned int sts;
- 	unsigned int sts2;
-+	irqreturn_t ret = IRQ_NONE;
- 
- 	sts = readl(sport->port.membase + USR1);
- 	sts2 = readl(sport->port.membase + USR2);
-@@ -762,26 +763,34 @@ static irqreturn_t imx_int(int irq, void
- 			imx_dma_rxint(sport);
- 		else
- 			imx_rxint(irq, dev_id);
-+		ret = IRQ_HANDLED;
- 	}
- 
- 	if ((sts & USR1_TRDY &&
- 	     readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN) ||
- 	    (sts2 & USR2_TXDC &&
--	     readl(sport->port.membase + UCR4) & UCR4_TCEN))
-+	     readl(sport->port.membase + UCR4) & UCR4_TCEN)) {
- 		imx_txint(irq, dev_id);
-+		ret = IRQ_HANDLED;
-+	}
- 
--	if (sts & USR1_RTSD)
-+	if (sts & USR1_RTSD) {
- 		imx_rtsint(irq, dev_id);
-+		ret = IRQ_HANDLED;
-+	}
- 
--	if (sts & USR1_AWAKE)
-+	if (sts & USR1_AWAKE) {
- 		writel(USR1_AWAKE, sport->port.membase + USR1);
-+		ret = IRQ_HANDLED;
-+	}
- 
- 	if (sts2 & USR2_ORE) {
- 		sport->port.icount.overrun++;
- 		writel(USR2_ORE, sport->port.membase + USR2);
-+		ret = IRQ_HANDLED;
- 	}
- 
--	return IRQ_HANDLED;
-+	return ret;
- }
- 
- /*

target/linux/imx6/patches-4.4/113-serial-imx-make-sure-unhandled-irqs-are-disabled.patch

@@ -1,56 +0,0 @@
-From a58c6360b9eb3a2374b0b069ba9ce7baec0f26df Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= <[email protected]>
-Date: Thu, 24 Mar 2016 14:24:22 +0100
-Subject: [PATCH 3/3] serial: imx: make sure unhandled irqs are disabled
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Make sure that events that are not handled in the irq function don't
-trigger an interrupt.
-
-When the serial port is operated in DTE mode, the events for DCD and RI
-events are enabled after a system reset by default.
-
-Signed-off-by: Uwe Kleine-König <[email protected]>
-Signed-off-by: Petr Štetiar <[email protected]>
----
- drivers/tty/serial/imx.c | 23 ++++++++++++++++++++++-
- 1 file changed, 22 insertions(+), 1 deletion(-)
-
---- a/drivers/tty/serial/imx.c
-+++ b/drivers/tty/serial/imx.c
-@@ -1184,11 +1184,32 @@ static int imx_startup(struct uart_port
- 	temp |= (UCR2_RXEN | UCR2_TXEN);
- 	if (!sport->have_rtscts)
- 		temp |= UCR2_IRTS;
-+	/*
-+	 * make sure the edge sensitive RTS-irq is disabled,
-+	 * we're using RTSD instead.
-+	 */
-+	if (!is_imx1_uart(sport))
-+		temp &= ~UCR2_RTSEN;
- 	writel(temp, sport->port.membase + UCR2);
- 
- 	if (!is_imx1_uart(sport)) {
- 		temp = readl(sport->port.membase + UCR3);
--		temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP;
-+
-+		/*
-+		 * The effect of RI and DCD differs depending on the UFCR_DCEDTE
-+		 * bit. In DCE mode they control the outputs, in DTE mode they
-+		 * enable the respective irqs. At least the DCD irq cannot be
-+		 * cleared on i.MX25 at least, so it's not usable and must be
-+		 * disabled. I don't have test hardware to check if RI has the
-+		 * same problem but I consider this likely so it's disabled for
-+		 * now, too.
-+		 */
-+		temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP |
-+			UCR3_RI | UCR3_DCD;
-+
-+		if (sport->dte_mode)
-+			temp &= ~(UCR3_RI | UCR3_DCD);
-+
- 		writel(temp, sport->port.membase + UCR3);
- 	}
- 

target/linux/imx6/patches-4.4/202-net-igb-add-i210-i211-support-for-phy-read-write.patch

@@ -1,129 +0,0 @@
-Author: Tim Harvey <[email protected]>
-Date:   Thu May 15 00:12:26 2014 -0700
-
-    net: igb: add i210/i211 support for phy read/write
-    
-    The i210/i211 uses the MDICNFG register for the phy address instead of the
-    MDIC register.
-    
-    Signed-off-by: Tim Harvey <[email protected]>
-
---- a/drivers/net/ethernet/intel/igb/e1000_phy.c
-+++ b/drivers/net/ethernet/intel/igb/e1000_phy.c
-@@ -133,7 +133,7 @@ out:
- s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
- {
- 	struct e1000_phy_info *phy = &hw->phy;
--	u32 i, mdic = 0;
-+	u32 i, mdicnfg, mdic = 0;
- 	s32 ret_val = 0;
- 
- 	if (offset > MAX_PHY_REG_ADDRESS) {
-@@ -146,11 +146,25 @@ s32 igb_read_phy_reg_mdic(struct e1000_h
- 	 * Control register.  The MAC will take care of interfacing with the
- 	 * PHY to retrieve the desired data.
- 	 */
--	mdic = ((offset << E1000_MDIC_REG_SHIFT) |
--		(phy->addr << E1000_MDIC_PHY_SHIFT) |
--		(E1000_MDIC_OP_READ));
-+	switch (hw->mac.type) {
-+	case e1000_i210:
-+	case e1000_i211:
-+		mdicnfg = rd32(E1000_MDICNFG);
-+		mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
-+		mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
-+		wr32(E1000_MDICNFG, mdicnfg);
-+		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
-+			(E1000_MDIC_OP_READ));
-+		break;
-+	default:
-+		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
-+			(phy->addr << E1000_MDIC_PHY_SHIFT) |
-+			(E1000_MDIC_OP_READ));
-+		break;
-+	}
- 
- 	wr32(E1000_MDIC, mdic);
-+	wrfl();
- 
- 	/* Poll the ready bit to see if the MDI read completed
- 	 * Increasing the time out as testing showed failures with
-@@ -175,6 +189,18 @@ s32 igb_read_phy_reg_mdic(struct e1000_h
- 	*data = (u16) mdic;
- 
- out:
-+	switch (hw->mac.type) {
-+		/* restore MDICNFG to have phy's addr */
-+		case e1000_i210:
-+		case e1000_i211:
-+			mdicnfg = rd32(E1000_MDICNFG);
-+			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
-+			mdicnfg |= (hw->phy.addr << E1000_MDICNFG_PHY_SHIFT);
-+			wr32(E1000_MDICNFG, mdicnfg);
-+			break;
-+		default:
-+			break;
-+	}
- 	return ret_val;
- }
- 
-@@ -189,7 +215,7 @@ out:
- s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
- {
- 	struct e1000_phy_info *phy = &hw->phy;
--	u32 i, mdic = 0;
-+	u32 i, mdicnfg, mdic = 0;
- 	s32 ret_val = 0;
- 
- 	if (offset > MAX_PHY_REG_ADDRESS) {
-@@ -202,12 +228,27 @@ s32 igb_write_phy_reg_mdic(struct e1000_
- 	 * Control register.  The MAC will take care of interfacing with the
- 	 * PHY to retrieve the desired data.
- 	 */
--	mdic = (((u32)data) |
--		(offset << E1000_MDIC_REG_SHIFT) |
--		(phy->addr << E1000_MDIC_PHY_SHIFT) |
--		(E1000_MDIC_OP_WRITE));
-+	switch (hw->mac.type) {
-+		case e1000_i210:
-+		case e1000_i211:
-+			mdicnfg = rd32(E1000_MDICNFG);
-+			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
-+			mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
-+			wr32(E1000_MDICNFG, mdicnfg);
-+			mdic = (((u32)data) |
-+				(offset << E1000_MDIC_REG_SHIFT) |
-+				(E1000_MDIC_OP_WRITE));
-+			break;
-+		default:
-+			mdic = (((u32)data) |
-+				(offset << E1000_MDIC_REG_SHIFT) |
-+				(phy->addr << E1000_MDIC_PHY_SHIFT) |
-+				(E1000_MDIC_OP_WRITE));
-+			break;
-+	}
- 
- 	wr32(E1000_MDIC, mdic);
-+	wrfl();
- 
- 	/* Poll the ready bit to see if the MDI read completed
- 	 * Increasing the time out as testing showed failures with
-@@ -231,6 +272,18 @@ s32 igb_write_phy_reg_mdic(struct e1000_
- 	}
- 
- out:
-+	switch (hw->mac.type) {
-+		/* restore MDICNFG to have phy's addr */
-+		case e1000_i210:
-+		case e1000_i211:
-+			mdicnfg = rd32(E1000_MDICNFG);
-+			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
-+			mdicnfg |= (hw->phy.addr << E1000_MDICNFG_PHY_SHIFT);
-+			wr32(E1000_MDICNFG, mdicnfg);
-+			break;
-+		default:
-+			break;
-+	}
- 	return ret_val;
- }
- 

target/linux/imx6/patches-4.4/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch

@@ -1,260 +0,0 @@
-From 16df7dc5901c1cb2a40f6adbd0d9423768ed8210 Mon Sep 17 00:00:00 2001
-From: Tim Harvey <[email protected]>
-Date: Thu, 15 May 2014 00:29:18 -0700
-Subject: [PATCH] net: igb: add phy read/write functions that accept phy addr
-
-Add igb_write_reg_gs40g/igb_read_reg_gs40g that can be passed a phy address.
-The existing igb_write_phy_reg_gs40g/igb_read_phy_reg_gs40g become wrappers
-to this function.
-
-Signed-off-by: Tim Harvey <[email protected]>
----
- drivers/net/ethernet/intel/igb/e1000_82575.c |  4 +-
- drivers/net/ethernet/intel/igb/e1000_phy.c   | 74 +++++++++++++++++++---------
- drivers/net/ethernet/intel/igb/e1000_phy.h   |  6 ++-
- 3 files changed, 58 insertions(+), 26 deletions(-)
-
---- a/drivers/net/ethernet/intel/igb/e1000_82575.c
-+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
-@@ -2154,7 +2154,7 @@ static s32 igb_read_phy_reg_82580(struct
- 	if (ret_val)
- 		goto out;
- 
--	ret_val = igb_read_phy_reg_mdic(hw, offset, data);
-+	ret_val = igb_read_phy_reg_mdic(hw, hw->phy.addr, offset, data);
- 
- 	hw->phy.ops.release(hw);
- 
-@@ -2179,7 +2179,7 @@ static s32 igb_write_phy_reg_82580(struc
- 	if (ret_val)
- 		goto out;
- 
--	ret_val = igb_write_phy_reg_mdic(hw, offset, data);
-+	ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr, offset, data);
- 
- 	hw->phy.ops.release(hw);
- 
---- a/drivers/net/ethernet/intel/igb/e1000_phy.c
-+++ b/drivers/net/ethernet/intel/igb/e1000_phy.c
-@@ -130,9 +130,8 @@ out:
-  *  Reads the MDI control regsiter in the PHY at offset and stores the
-  *  information read to data.
-  **/
--s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
-+s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data)
- {
--	struct e1000_phy_info *phy = &hw->phy;
- 	u32 i, mdicnfg, mdic = 0;
- 	s32 ret_val = 0;
- 
-@@ -151,14 +150,14 @@ s32 igb_read_phy_reg_mdic(struct e1000_h
- 	case e1000_i211:
- 		mdicnfg = rd32(E1000_MDICNFG);
- 		mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
--		mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
-+		mdicnfg |= (addr << E1000_MDICNFG_PHY_SHIFT);
- 		wr32(E1000_MDICNFG, mdicnfg);
- 		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
- 			(E1000_MDIC_OP_READ));
- 		break;
- 	default:
- 		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
--			(phy->addr << E1000_MDIC_PHY_SHIFT) |
-+			(addr << E1000_MDIC_PHY_SHIFT) |
- 			(E1000_MDIC_OP_READ));
- 		break;
- 	}
-@@ -212,9 +211,8 @@ out:
-  *
-  *  Writes data to MDI control register in the PHY at offset.
-  **/
--s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
-+s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 data)
- {
--	struct e1000_phy_info *phy = &hw->phy;
- 	u32 i, mdicnfg, mdic = 0;
- 	s32 ret_val = 0;
- 
-@@ -233,7 +231,7 @@ s32 igb_write_phy_reg_mdic(struct e1000_
- 		case e1000_i211:
- 			mdicnfg = rd32(E1000_MDICNFG);
- 			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
--			mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
-+			mdicnfg |= (addr << E1000_MDICNFG_PHY_SHIFT);
- 			wr32(E1000_MDICNFG, mdicnfg);
- 			mdic = (((u32)data) |
- 				(offset << E1000_MDIC_REG_SHIFT) |
-@@ -242,7 +240,7 @@ s32 igb_write_phy_reg_mdic(struct e1000_
- 		default:
- 			mdic = (((u32)data) |
- 				(offset << E1000_MDIC_REG_SHIFT) |
--				(phy->addr << E1000_MDIC_PHY_SHIFT) |
-+				(addr << E1000_MDIC_PHY_SHIFT) |
- 				(E1000_MDIC_OP_WRITE));
- 			break;
- 	}
-@@ -462,7 +460,7 @@ s32 igb_read_phy_reg_igp(struct e1000_hw
- 		goto out;
- 
- 	if (offset > MAX_PHY_MULTI_PAGE_REG) {
--		ret_val = igb_write_phy_reg_mdic(hw,
-+		ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
- 						 IGP01E1000_PHY_PAGE_SELECT,
- 						 (u16)offset);
- 		if (ret_val) {
-@@ -471,8 +469,8 @@ s32 igb_read_phy_reg_igp(struct e1000_hw
- 		}
- 	}
- 
--	ret_val = igb_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
--					data);
-+	ret_val = igb_read_phy_reg_mdic(hw, hw->phy.addr,
-+					MAX_PHY_REG_ADDRESS & offset, data);
- 
- 	hw->phy.ops.release(hw);
- 
-@@ -501,7 +499,7 @@ s32 igb_write_phy_reg_igp(struct e1000_h
- 		goto out;
- 
- 	if (offset > MAX_PHY_MULTI_PAGE_REG) {
--		ret_val = igb_write_phy_reg_mdic(hw,
-+		ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
- 						 IGP01E1000_PHY_PAGE_SELECT,
- 						 (u16)offset);
- 		if (ret_val) {
-@@ -510,8 +508,8 @@ s32 igb_write_phy_reg_igp(struct e1000_h
- 		}
- 	}
- 
--	ret_val = igb_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
--					 data);
-+	ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
-+					 MAX_PHY_REG_ADDRESS & offset, data);
- 
- 	hw->phy.ops.release(hw);
- 
-@@ -2551,8 +2549,9 @@ out:
- }
- 
- /**
-- *  igb_write_phy_reg_gs40g - Write GS40G PHY register
-+ *  igb_write_reg_gs40g - Write GS40G PHY register
-  *  @hw: pointer to the HW structure
-+ *  @addr: phy address to write to
-  *  @offset: lower half is register offset to write to
-  *     upper half is page to use.
-  *  @data: data to write at register offset
-@@ -2560,7 +2559,7 @@ out:
-  *  Acquires semaphore, if necessary, then writes the data to PHY register
-  *  at the offset.  Release any acquired semaphores before exiting.
-  **/
--s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data)
-+s32 igb_write_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 data)
- {
- 	s32 ret_val;
- 	u16 page = offset >> GS40G_PAGE_SHIFT;
-@@ -2570,10 +2569,10 @@ s32 igb_write_phy_reg_gs40g(struct e1000
- 	if (ret_val)
- 		return ret_val;
- 
--	ret_val = igb_write_phy_reg_mdic(hw, GS40G_PAGE_SELECT, page);
-+	ret_val = igb_write_phy_reg_mdic(hw, addr, GS40G_PAGE_SELECT, page);
- 	if (ret_val)
- 		goto release;
--	ret_val = igb_write_phy_reg_mdic(hw, offset, data);
-+	ret_val = igb_write_phy_reg_mdic(hw, addr, offset, data);
- 
- release:
- 	hw->phy.ops.release(hw);
-@@ -2581,8 +2580,24 @@ release:
- }
- 
- /**
-- *  igb_read_phy_reg_gs40g - Read GS40G  PHY register
-+ *  igb_write_phy_reg_gs40g - Write GS40G PHY register
-+ *  @hw: pointer to the HW structure
-+ *  @offset: lower half is register offset to write to
-+ *     upper half is page to use.
-+ *  @data: data to write at register offset
-+ *
-+ *  Acquires semaphore, if necessary, then writes the data to PHY register
-+ *  at the offset.  Release any acquired semaphores before exiting.
-+ **/
-+s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data)
-+{
-+	return igb_write_reg_gs40g(hw, hw->phy.addr, offset, data);
-+}
-+
-+/**
-+ *  igb_read_reg_gs40g - Read GS40G  PHY register
-  *  @hw: pointer to the HW structure
-+ *  @addr: phy address to read from
-  *  @offset: lower half is register offset to read to
-  *     upper half is page to use.
-  *  @data: data to read at register offset
-@@ -2590,7 +2605,7 @@ release:
-  *  Acquires semaphore, if necessary, then reads the data in the PHY register
-  *  at the offset.  Release any acquired semaphores before exiting.
-  **/
--s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data)
-+s32 igb_read_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data)
- {
- 	s32 ret_val;
- 	u16 page = offset >> GS40G_PAGE_SHIFT;
-@@ -2600,10 +2615,10 @@ s32 igb_read_phy_reg_gs40g(struct e1000_
- 	if (ret_val)
- 		return ret_val;
- 
--	ret_val = igb_write_phy_reg_mdic(hw, GS40G_PAGE_SELECT, page);
-+	ret_val = igb_write_phy_reg_mdic(hw, addr, GS40G_PAGE_SELECT, page);
- 	if (ret_val)
- 		goto release;
--	ret_val = igb_read_phy_reg_mdic(hw, offset, data);
-+	ret_val = igb_read_phy_reg_mdic(hw, addr, offset, data);
- 
- release:
- 	hw->phy.ops.release(hw);
-@@ -2611,6 +2626,21 @@ release:
- }
- 
- /**
-+ *  igb_read_phy_reg_gs40g - Read GS40G  PHY register
-+ *  @hw: pointer to the HW structure
-+ *  @offset: lower half is register offset to read to
-+ *     upper half is page to use.
-+ *  @data: data to read at register offset
-+ *
-+ *  Acquires semaphore, if necessary, then reads the data in the PHY register
-+ *  at the offset.  Release any acquired semaphores before exiting.
-+ **/
-+s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data)
-+{
-+	return igb_read_reg_gs40g(hw, hw->phy.addr, offset, data);
-+}
-+
-+/**
-  *  igb_set_master_slave_mode - Setup PHY for Master/slave mode
-  *  @hw: pointer to the HW structure
-  *
---- a/drivers/net/ethernet/intel/igb/e1000_phy.h
-+++ b/drivers/net/ethernet/intel/igb/e1000_phy.h
-@@ -62,8 +62,8 @@ void igb_power_up_phy_copper(struct e100
- void igb_power_down_phy_copper(struct e1000_hw *hw);
- s32  igb_phy_init_script_igp3(struct e1000_hw *hw);
- s32  igb_initialize_M88E1512_phy(struct e1000_hw *hw);
--s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
--s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
-+s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data);
-+s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 data);
- s32  igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
- s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
- s32  igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data);
-@@ -73,6 +73,8 @@ s32  igb_phy_force_speed_duplex_82580(st
- s32  igb_get_cable_length_82580(struct e1000_hw *hw);
- s32  igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data);
- s32  igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data);
-+s32  igb_read_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data);
-+s32  igb_write_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 data);
- s32  igb_check_polarity_m88(struct e1000_hw *hw);
- 
- /* IGP01E1000 Specific Registers */

target/linux/imx6/patches-4.4/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch

@@ -1,308 +0,0 @@
-From 03855caf93f7332a3f320228ba1a0e7baae8a749 Mon Sep 17 00:00:00 2001
-From: Tim Harvey <[email protected]>
-Date: Thu, 15 May 2014 12:36:23 -0700
-Subject: [PATCH] net: igb: register mii_bus for SerDes w/ external phy
-
-If an i210 is configured for 1000BASE-BX link_mode and has an external phy
-specified, then register an mii bus using the external phy address as
-a mask.
-
-An i210 hooked to an external standard phy will be configured with a link_mo
-of SGMII in which case phy ops will be configured and used internall in the
-igb driver for link status. However, in certain cases one might be using a
-backplane SerDes connection to something that talks on the mdio bus but is
-not a standard phy, such as a switch. In this case by registering an mdio
-bus a phy driver can manage the device.
-
-Signed-off-by: Tim Harvey <[email protected]>
----
- drivers/net/ethernet/intel/igb/e1000_82575.c |  15 +++
- drivers/net/ethernet/intel/igb/e1000_hw.h    |   7 ++
- drivers/net/ethernet/intel/igb/igb_main.c    | 168 ++++++++++++++++++++++++++-
- 3 files changed, 185 insertions(+), 5 deletions(-)
-
---- a/drivers/net/ethernet/intel/igb/e1000_82575.c
-+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
-@@ -613,13 +613,25 @@ static s32 igb_get_invariants_82575(stru
- 	switch (link_mode) {
- 	case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
- 		hw->phy.media_type = e1000_media_type_internal_serdes;
-+		if (igb_sgmii_uses_mdio_82575(hw)) {
-+			u32 mdicnfg = rd32(E1000_MDICNFG);
-+			mdicnfg &= E1000_MDICNFG_PHY_MASK;
-+			hw->phy.addr = mdicnfg >> E1000_MDICNFG_PHY_SHIFT;
-+			hw_dbg("1000BASE_KX w/ external MDIO device at 0x%x\n",
-+			       hw->phy.addr);
-+		} else {
-+			hw_dbg("1000BASE_KX");
-+		}
- 		break;
- 	case E1000_CTRL_EXT_LINK_MODE_SGMII:
- 		/* Get phy control interface type set (MDIO vs. I2C)*/
- 		if (igb_sgmii_uses_mdio_82575(hw)) {
- 			hw->phy.media_type = e1000_media_type_copper;
- 			dev_spec->sgmii_active = true;
-+			hw_dbg("SGMII with external MDIO PHY");
- 			break;
-+		} else {
-+			hw_dbg("SGMII with external I2C PHY");
- 		}
- 		/* fall through for I2C based SGMII */
- 	case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
-@@ -636,8 +648,11 @@ static s32 igb_get_invariants_82575(stru
- 				hw->phy.media_type = e1000_media_type_copper;
- 				dev_spec->sgmii_active = true;
- 			}
-+			hw_dbg("SERDES with external SFP");
- 
- 			break;
-+		} else {
-+			hw_dbg("SERDES");
- 		}
- 
- 		/* do not change link mode for 100BaseFX */
---- a/drivers/net/ethernet/intel/igb/e1000_hw.h
-+++ b/drivers/net/ethernet/intel/igb/e1000_hw.h
-@@ -27,6 +27,7 @@
- #include <linux/delay.h>
- #include <linux/io.h>
- #include <linux/netdevice.h>
-+#include <linux/phy.h>
- 
- #include "e1000_regs.h"
- #include "e1000_defines.h"
-@@ -543,6 +544,12 @@ struct e1000_hw {
- 	struct e1000_mbx_info mbx;
- 	struct e1000_host_mng_dhcp_cookie mng_cookie;
- 
-+#ifdef CONFIG_PHYLIB
-+	/* Phylib and MDIO interface */
-+	struct mii_bus *mii_bus;
-+	struct phy_device *phy_dev;
-+	phy_interface_t phy_interface;
-+#endif
- 	union {
- 		struct e1000_dev_spec_82575	_82575;
- 	} dev_spec;
---- a/drivers/net/ethernet/intel/igb/igb_main.c
-+++ b/drivers/net/ethernet/intel/igb/igb_main.c
-@@ -41,6 +41,7 @@
- #include <linux/if_vlan.h>
- #include <linux/pci.h>
- #include <linux/pci-aspm.h>
-+#include <linux/phy.h>
- #include <linux/delay.h>
- #include <linux/interrupt.h>
- #include <linux/ip.h>
-@@ -2217,6 +2218,126 @@ static s32 igb_init_i2c(struct igb_adapt
- 	return status;
- }
- 
-+
-+#ifdef CONFIG_PHYLIB
-+/*
-+ * MMIO/PHYdev support
-+ */
-+
-+static int igb_enet_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
-+{
-+	struct e1000_hw *hw = bus->priv;
-+	u16 out;
-+	int err;
-+
-+	err = igb_read_reg_gs40g(hw, mii_id, regnum, &out);
-+	if (err)
-+		return err;
-+	return out;
-+}
-+
-+static int igb_enet_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
-+                               u16 val)
-+{
-+	struct e1000_hw *hw = bus->priv;
-+
-+	return igb_write_reg_gs40g(hw, mii_id, regnum, val);
-+}
-+
-+static int igb_enet_mdio_reset(struct mii_bus *bus)
-+{
-+	udelay(300);
-+	return 0;
-+}
-+
-+static void igb_enet_mii_link(struct net_device *netdev)
-+{
-+}
-+
-+/* Probe the mdio bus for phys and connect them */
-+static int igb_enet_mii_probe(struct net_device *netdev)
-+{
-+	struct igb_adapter *adapter = netdev_priv(netdev);
-+	struct e1000_hw *hw = &adapter->hw;
-+	struct phy_device *phy_dev = NULL;
-+	int phy_id;
-+
-+	/* check for attached phy */
-+	for (phy_id = 0; (phy_id < PHY_MAX_ADDR); phy_id++) {
-+		if (hw->mii_bus->phy_map[phy_id]) {
-+			phy_dev = hw->mii_bus->phy_map[phy_id];
-+			break;
-+		}
-+	}
-+	if (!phy_dev) {
-+		netdev_err(netdev, "no PHY found\n");
-+		return -ENODEV;
-+	}
-+
-+	hw->phy_interface = PHY_INTERFACE_MODE_RGMII;
-+	phy_dev = phy_connect(netdev, dev_name(&phy_dev->dev),
-+			      igb_enet_mii_link, hw->phy_interface);
-+	if (IS_ERR(phy_dev)) {
-+		netdev_err(netdev, "could not attach to PHY\n");
-+		return PTR_ERR(phy_dev);
-+	}
-+
-+	hw->phy_dev = phy_dev;
-+	netdev_info(netdev, "igb PHY driver [%s] (mii_bus:phy_addr=%s)\n",
-+		hw->phy_dev->drv->name, dev_name(&hw->phy_dev->dev));
-+
-+	return 0;
-+}
-+
-+/* Create and register mdio bus */
-+static int igb_enet_mii_init(struct pci_dev *pdev)
-+{
-+	struct mii_bus *mii_bus;
-+	struct net_device *netdev = pci_get_drvdata(pdev);
-+	struct igb_adapter *adapter = netdev_priv(netdev);
-+	struct e1000_hw *hw = &adapter->hw;
-+	int err;
-+
-+	mii_bus = mdiobus_alloc();
-+	if (mii_bus == NULL) {
-+		err = -ENOMEM;
-+		goto err_out;
-+	}
-+
-+	mii_bus->name = "igb_enet_mii_bus";
-+	mii_bus->read = igb_enet_mdio_read;
-+	mii_bus->write = igb_enet_mdio_write;
-+	mii_bus->reset = igb_enet_mdio_reset;
-+	snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s-%x",
-+		 pci_name(pdev), hw->device_id + 1);
-+	mii_bus->priv = hw;
-+	mii_bus->parent = &pdev->dev;
-+	mii_bus->phy_mask = ~(1 << hw->phy.addr);
-+
-+	err = mdiobus_register(mii_bus);
-+	if (err) {
-+		printk(KERN_ERR "failed to register mii_bus: %d\n", err);
-+		goto err_out_free_mdiobus;
-+	}
-+	hw->mii_bus = mii_bus;
-+
-+	return 0;
-+
-+err_out_free_mdiobus:
-+	mdiobus_free(mii_bus);
-+err_out:
-+	return err;
-+}
-+
-+static void igb_enet_mii_remove(struct e1000_hw *hw)
-+{
-+	if (hw->mii_bus) {
-+		mdiobus_unregister(hw->mii_bus);
-+		mdiobus_free(hw->mii_bus);
-+	}
-+}
-+#endif /* CONFIG_PHYLIB */
-+
- /**
-  *  igb_probe - Device Initialization Routine
-  *  @pdev: PCI device information struct
-@@ -2641,6 +2762,13 @@ static int igb_probe(struct pci_dev *pde
- 		}
- 	}
- 	pm_runtime_put_noidle(&pdev->dev);
-+
-+#ifdef CONFIG_PHYLIB
-+	/* create and register the mdio bus if using ext phy */
-+	if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
-+		igb_enet_mii_init(pdev);
-+#endif
-+
- 	return 0;
- 
- err_register:
-@@ -2788,6 +2916,10 @@ static void igb_remove(struct pci_dev *p
- 	struct e1000_hw *hw = &adapter->hw;
- 
- 	pm_runtime_get_noresume(&pdev->dev);
-+#ifdef CONFIG_PHYLIB
-+	if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
-+		igb_enet_mii_remove(hw);
-+#endif
- #ifdef CONFIG_IGB_HWMON
- 	igb_sysfs_exit(adapter);
- #endif
-@@ -3111,6 +3243,12 @@ static int __igb_open(struct net_device
- 	if (!resuming)
- 		pm_runtime_put(&pdev->dev);
- 
-+#ifdef CONFIG_PHYLIB
-+	/* Probe and connect to PHY if using ext phy */
-+	if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
-+		igb_enet_mii_probe(netdev);
-+#endif
-+
- 	/* start the watchdog. */
- 	hw->mac.get_link_status = 1;
- 	schedule_work(&adapter->watchdog_task);
-@@ -7102,21 +7240,41 @@ void igb_alloc_rx_buffers(struct igb_rin
- static int igb_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
- {
- 	struct igb_adapter *adapter = netdev_priv(netdev);
-+	struct e1000_hw *hw = &adapter->hw;
- 	struct mii_ioctl_data *data = if_mii(ifr);
- 
--	if (adapter->hw.phy.media_type != e1000_media_type_copper)
-+	if (adapter->hw.phy.media_type != e1000_media_type_copper &&
-+	    !(rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO))
- 		return -EOPNOTSUPP;
- 
- 	switch (cmd) {
- 	case SIOCGMIIPHY:
--		data->phy_id = adapter->hw.phy.addr;
-+		data->phy_id = hw->phy.addr;
- 		break;
- 	case SIOCGMIIREG:
--		if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
--				     &data->val_out))
--			return -EIO;
-+		if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
-+			if (igb_read_reg_gs40g(&adapter->hw, data->phy_id,
-+					       data->reg_num & 0x1F,
-+			                       &data->val_out))
-+				return -EIO;
-+		} else {
-+			if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
-+			                     &data->val_out))
-+				return -EIO;
-+		}
- 		break;
- 	case SIOCSMIIREG:
-+		if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
-+			if (igb_write_reg_gs40g(hw, data->phy_id,
-+					        data->reg_num & 0x1F,
-+					        data->val_in))
-+				return -EIO;
-+		} else {
-+			if (igb_write_phy_reg(hw, data->reg_num & 0x1F,
-+					      data->val_in))
-+				return -EIO;
-+		}
-+		break;
- 	default:
- 		return -EOPNOTSUPP;
- 	}

target/linux/imx6/patches-4.4/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch

@@ -1,27 +0,0 @@
---- a/drivers/net/phy/Kconfig
-+++ b/drivers/net/phy/Kconfig
-@@ -336,6 +336,14 @@ endif # RTL8366_SMI
- 
- source "drivers/net/phy/b53/Kconfig"
- 
-+config GATEWORKS_GW16083
-+	tristate "Gateworks GW16083 Ethernet Expansion Mezzanine"
-+	---help---
-+	  The Gateworks GW16083 Ethernet Expansion Mezzanine connects to a
-+	  Gateworks Ventana baseboard and provides a 7-port GbE managed
-+	  Ethernet switch with 4 dedicated GbE RJ45 ports, and 2 Gbe/SFP
-+	  ports"
-+
- endif # PHYLIB
- 
- config MICREL_KS8995MA
---- a/drivers/net/phy/Makefile
-+++ b/drivers/net/phy/Makefile
-@@ -46,6 +46,7 @@ obj-$(CONFIG_DP83848_PHY)	+= dp83848.o
- obj-$(CONFIG_DP83867_PHY)	+= dp83867.o
- obj-$(CONFIG_STE10XP)		+= ste10Xp.o
- obj-$(CONFIG_MICREL_PHY)	+= micrel.o
-+obj-$(CONFIG_GATEWORKS_GW16083)	+= gw16083.o
- obj-$(CONFIG_MDIO_OCTEON)	+= mdio-octeon.o
- obj-$(CONFIG_MICREL_KS8995MA)	+= spi_ks8995.o
- obj-$(CONFIG_AT803X_PHY)	+= at803x.o

target/linux/imx6/patches-4.4/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch

@@ -1,56 +0,0 @@
---- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
-@@ -158,6 +158,11 @@
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_i2c2>;
- 	status = "okay";
-+
-+	gw16083: gw16083@52 {
-+		compatible = "gateworks,gw16083";
-+		reg = <0x52>;
-+	};
- };
- 
- &i2c3 {
---- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
-@@ -233,6 +233,11 @@
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_i2c2>;
- 	status = "okay";
-+
-+	gw16083: gw16083@52 {
-+		compatible = "gateworks,gw16083";
-+		reg = <0x52>;
-+	};
- };
- 
- &i2c3 {
---- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-@@ -226,6 +226,11 @@
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&pinctrl_i2c2>;
- 	status = "okay";
-+
-+	gw16083: gw16083@52 {
-+		compatible = "gateworks,gw16083";
-+		reg = <0x52>;
-+	};
- };
- 
- &i2c3 {
---- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-@@ -317,6 +317,11 @@
- 			};
- 		};
- 	};
-+
-+	gw16083: gw16083@52 {
-+		compatible = "gateworks,gw16083";
-+		reg = <0x52>;
-+	};
- };
- 
- &i2c3 {

target/linux/imx6/patches-4.4/207-i2c-imx-add-retries-for-NAK-s-on-ventana-boards.patch

@@ -1,22 +0,0 @@
---- a/drivers/i2c/busses/i2c-imx.c
-+++ b/drivers/i2c/busses/i2c-imx.c
-@@ -468,6 +468,8 @@ static int i2c_imx_acked(struct imx_i2c_
- {
- 	if (imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR) & I2SR_RXAK) {
- 		dev_dbg(&i2c_imx->adapter.dev, "<%s> No ACK\n", __func__);
-+		if (i2c_imx->adapter.retries)
-+			return -EAGAIN;
- 		return -ENXIO;  /* No ACK */
- 	}
- 
-@@ -1073,6 +1075,10 @@ static int i2c_imx_probe(struct platform
- 	i2c_imx->adapter.nr		= pdev->id;
- 	i2c_imx->adapter.dev.of_node	= pdev->dev.of_node;
- 	i2c_imx->base			= base;
-+	if (of_machine_is_compatible("gw,ventana") && phy_addr == 0x021a0000) {
-+		dev_info(&pdev->dev, "Adding retries for Ventana GSC\n");
-+		i2c_imx->adapter.retries = 3;
-+	}
- 
- 	/* Get I2C clock */
- 	i2c_imx->clk = devm_clk_get(&pdev->dev, NULL);

target/linux/imx6/patches-4.4/208-sky2-allow-mac-to-come-from-dt.patch

@@ -1,28 +0,0 @@
---- a/drivers/net/ethernet/marvell/sky2.c
-+++ b/drivers/net/ethernet/marvell/sky2.c
-@@ -4812,7 +4812,24 @@ static struct net_device *sky2_init_netd
- 	 * 1) from device tree data
- 	 * 2) from internal registers set by bootloader
- 	 */
--	iap = of_get_mac_address(hw->pdev->dev.of_node);
-+
-+	iap = NULL;
-+	if (IS_ENABLED(CONFIG_OF)) {
-+		struct device_node *np;
-+		np = of_find_node_by_path("/aliases");
-+		if (np) {
-+			const char *path = of_get_property(np, "sky2", NULL);
-+			if (path)
-+				np = of_find_node_by_path(path);
-+			if (np)
-+				path = of_get_mac_address(np);
-+			if (path)
-+				iap = (unsigned char *) path;
-+		}
-+	}
-+
-+	if (!iap)
-+		iap = of_get_mac_address(hw->pdev->dev.of_node);
- 	if (iap)
- 		memcpy(dev->dev_addr, iap, ETH_ALEN);
- 	else

target/linux/imx6/patches-4.4/209-ARM-imx-ventana-add-sky2-alias.patch

@@ -1,20 +0,0 @@
---- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
-@@ -15,6 +15,7 @@
- 	/* these are used by bootloader for disabling nodes */
- 	aliases {
- 		ethernet1 = &eth1;
-+		sky2 = &eth1;
- 		led0 = &led0;
- 		led1 = &led1;
- 		led2 = &led2;
---- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
-@@ -15,6 +15,7 @@
- 	/* these are used by bootloader for disabling nodes */
- 	aliases {
- 		ethernet1 = &eth1;
-+		sky2 = &eth1;
- 		led0 = &led0;
- 		led1 = &led1;
- 		led2 = &led2;