(respin) 802.1Q VLAN support for ADM6996M/ADM6996FC

This patch adds 802.1Q VLAN support for the ADM6996M chip.

The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.

The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].

Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt

Signed-of-By: Peter Lebbing <[email protected]>

SVN-Revision: 26865

target/linux/generic/files/Documentation/networking/adm6996.txt

@@ -0,0 +1,110 @@
+------- 
+
+ADM6996FC / ADM6996M switch chip driver
+
+
+1. General information
+
+  This driver supports the FC and M models only. The ADM6996F and L are
+  completely different chips.
+  
+  Support for the FC model is extremely limited at the moment. There is no VLAN
+  support as of yet. The driver will not offer an swconfig interface for the FC
+  chip.
+ 
+1.1 VLAN IDs
+
+  It is possible to define 16 different VLANs. Every VLAN has an identifier, its
+  VLAN ID. It is easiest if you use at most VLAN IDs 0-15. In that case, the
+  swconfig based configuration is very straightforward. To define two VLANs with
+  IDs 4 and 5, you can invoke, for example:
+  
+      # swconfig dev ethX vlan 4 set ports '0 1t 2 5t' 
+      # swconfig dev ethX vlan 5 set ports '0t 1t 5t'
+  
+  The swconfig framework will automatically invoke 'port Y set pvid Z' for every
+  port that is an untagged member of VLAN Y, setting its Primary VLAN ID. In
+  this example, ports 0 and 2 would get "pvid 4". The Primary VLAN ID of a port
+  is the VLAN ID associated with untagged packets coming in on that port.
+  
+  But if you wish to use VLAN IDs outside the range 0-15, this automatic
+  behaviour of the swconfig framework becomes a problem. The 16 VLANs that
+  swconfig can configure on the ADM6996 also have a "vid" setting. By default,
+  this is the same as the number of the VLAN entry, to make the simple behaviour
+  above possible. To still support a VLAN with a VLAN ID higher than 15
+  (presumably because you are in a network where such VLAN IDs are already in
+  use), you can change the "vid" setting of the VLAN to anything in the range
+  0-1023. But suppose you did the following:
+  
+      # swconfig dev ethX vlan 0 set vid 998 
+      # swconfig dev ethX vlan 0 set ports '0 2 5t'
+ 
+  Now the swconfig framework will issue 'port 0 set pvid 0' and 'port 2 set pvid
+  0'. But the "pvid" should be set to 998, so you are responsible for manually
+  fixing this!
+
+1.2 VLAN filtering
+
+  The switch is configured to apply source port filtering. This means that
+  packets are only accepted when the port the packets came in on is a member of
+  the VLAN the packet should go to.
+
+  Only membership of a VLAN is tested, it does not matter whether it is a tagged
+  or untagged membership.
+
+  For untagged packets, the destination VLAN is the Primary VLAN ID of the
+  incoming port. So if the PVID of a port is 0, but that port is not a member of
+  the VLAN with ID 0, this means that untagged packets on that port are dropped.
+  This can be used as a roundabout way of dropping untagged packets from a port,
+  a mode often referred to as "Admit only tagged packets".
+
+1.3 Reset
+
+  The two supported chip models do not have a sofware-initiated reset. When the
+  driver is initialised, as well as when the 'reset' swconfig option is invoked,
+  the driver will set those registers it knows about and supports to the correct
+  default value. But there are a lot of registers in the chip that the driver
+  does not support. If something changed those registers, invoking 'reset' or
+  performing a warm reboot might still leave the chip in a "broken" state. Only
+  a hardware reset will bring it back in the default state.
+
+2. Technical details on PHYs and the ADM6996
+
+  From the viewpoint of the Linux kernel, it is common that an Ethernet adapter
+  can be seen as a separate MAC entity and a separate PHY entity. The PHY entity
+  can be queried and set through registers accessible via an MDIO bus. A PHY
+  normally has a single address on that bus, in the range 0 through 31.
+
+  The ADM6996 has special-purpose registers in the range of PHYs 0 through 10.
+  Even though all these registers control a single ADM6996 chip, the Linux
+  kernel treats this as 11 separate PHYs.  The driver will bind to these
+  addresses to prevent a different PHY driver from binding and corrupting these
+  registers.
+
+  What Linux sees as the PHY on address 0 is meant for the Ethernet MAC
+  connected to the CPU port of the ADM6996 switch chip (port 5). This is the
+  Ethernet MAC you will use to send and receive data through the switch.
+
+  The PHYs at addresses 16 through 20 map to the PHYs on ports 0 through 4 of
+  the switch chip. These can be accessed with the Generic PHY driver, as the
+  registers have the common layout.
+
+  If a second Ethernet MAC on your board is wired to the port 4 PHY, that MAC
+  needs to bind to PHY address 20 for the port to work correctly.
+
+  The ADM6996 switch driver will reset the ports 0 through 3 on startup and when
+  'reset' is invoked. This could clash with a different PHY driver if the kernel
+  binds a PHY driver to address 16 through 19.
+
+  If Linux binds a PHY on addresses 1 through 10 to an Ethernet MAC, the ADM6996
+  driver will simply always report a connected 100 Mbit/s full-duplex link for
+  that PHY, and provide no other functionality. This is most likely not what you
+  want. So if you see a message in your log
+
+  	ethX: PHY overlaps ADM6996, providing fixed PHY yy.
+
+  This is most likely an indication that ethX will not work properly, and your
+  kernel needs to be configured to attach a different PHY to that Ethernet MAC.
+
+  Controlling the mapping between MACs and PHYs is usually done in platform- or
+  board-specific fixup code. The ADM6996 driver has no influence over this.

target/linux/generic/files/drivers/net/phy/adm6996.c

@@ -1,12 +1,17 @@
 /*
  * ADM6996 switch driver
  *
+ * swconfig interface based on ar8216.c
+ *
  * Copyright (c) 2008 Felix Fietkau <[email protected]>
+ * VLAN support Copyright (c) 2010, 2011 Peter Lebbing <[email protected]>
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of the GNU General Public License v2 as published by the
  * Free Software Foundation
  */
+
+/*#define DEBUG 1*/
 #include <linux/kernel.h>
 #include <linux/string.h>
 #include <linux/errno.h>
@@ -24,6 +29,7 @@
 #include <linux/mii.h>
 #include <linux/ethtool.h>
 #include <linux/phy.h>
+#include <linux/switch.h>
 
 #include <asm/io.h>
 #include <asm/irq.h>
@@ -31,28 +37,59 @@
 #include "adm6996.h"
 
 MODULE_DESCRIPTION("Infineon ADM6996 Switch");
-MODULE_AUTHOR("Felix Fietkau");
+MODULE_AUTHOR("Felix Fietkau, Peter Lebbing <[email protected]>");
 MODULE_LICENSE("GPL");
 
+enum adm6996_model {
+	ADM6996FC,
+	ADM6996M
+};
+
+static const char * const adm6996_model_name[] =
+{
+	"ADM6996FC",
+	"ADM6996M"
+};
+
 struct adm6996_priv {
+	struct switch_dev dev;
+	struct phy_device *phydev;
+
+	enum adm6996_model model;
+
+	bool enable_vlan;
+	bool vlan_enabled;	/* Current hardware state */
+
+#ifdef DEBUG
+	u16 addr;		/* Debugging: register address to operate on */
+#endif
+
+	u16 pvid[ADM_NUM_PORTS];	/* Primary VLAN ID */
+
+	u16 vlan_id[ADM_NUM_VLANS];
+	u8 vlan_table[ADM_NUM_VLANS];	/* bitmap, 1 = port is member */
+	u8 vlan_tagged[ADM_NUM_VLANS];	/* bitmap, 1 = tagged member */
+
+	struct mutex reg_mutex;
+
 	/* use abstraction for regops, we want to add gpio support in the future */
 	u16 (*read)(struct phy_device *phydev, enum admreg reg);
 	void (*write)(struct phy_device *phydev, enum admreg reg, u16 val);
 };
 
-#define to_adm(_phy) ((struct adm6996_priv *) (_phy)->priv)
-
+#define to_adm(_dev) container_of(_dev, struct adm6996_priv, dev)
+#define phy_to_adm(_phy) ((struct adm6996_priv *) (_phy)->priv)
 
 static inline u16
 r16(struct phy_device *pdev, enum admreg reg)
 {
-	return to_adm(pdev)->read(pdev, reg);
+	return phy_to_adm(pdev)->read(pdev, reg);
 }
 
 static inline void
 w16(struct phy_device *pdev, enum admreg reg, u16 val)
 {
-	to_adm(pdev)->write(pdev, reg, val);
+	phy_to_adm(pdev)->write(pdev, reg, val);
 }
 
 
@@ -68,30 +105,555 @@ adm6996_write_mii_reg(struct phy_device *phydev, enum admreg reg, u16 val)
 	phydev->bus->write(phydev->bus, PHYADDR(reg), val);
 }
 
+static int
+adm6996_set_enable_vlan(struct switch_dev *dev, const struct switch_attr *attr,
+			struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
 
-static int adm6996_config_init(struct phy_device *pdev)
+	if (val->value.i > 1)
+		return -EINVAL;
+
+	priv->enable_vlan = val->value.i;
+
+	return 0;
+};
+
+static int
+adm6996_get_enable_vlan(struct switch_dev *dev, const struct switch_attr *attr,
+			struct switch_val *val)
 {
+	struct adm6996_priv *priv = to_adm(dev);
+
+	val->value.i = priv->enable_vlan;
+
+	return 0;
+};
+
+#ifdef DEBUG
+
+static int
+adm6996_set_addr(struct switch_dev *dev, const struct switch_attr *attr,
+		 struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	if (val->value.i > 1023)
+		return -EINVAL;
+
+	priv->addr = val->value.i;
+
+	return 0;
+};
+
+static int
+adm6996_get_addr(struct switch_dev *dev, const struct switch_attr *attr,
+		 struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	val->value.i = priv->addr;
+
+	return 0;
+};
+
+static int
+adm6996_set_data(struct switch_dev *dev, const struct switch_attr *attr,
+		 struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	if (val->value.i > 65535)
+		return -EINVAL;
+
+	w16(priv->phydev, priv->addr, val->value.i);
+
+	return 0;
+};
+
+static int
+adm6996_get_data(struct switch_dev *dev, const struct switch_attr *attr,
+		 struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	val->value.i = r16(priv->phydev, priv->addr);
+
+	return 0;
+};
+
+#endif /* def DEBUG */
+
+static int
+adm6996_set_pvid(struct switch_dev *dev, int port, int vlan)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	dev_dbg (&priv->phydev->dev, "set_pvid port %d vlan %d\n", port
+			, vlan);
+
+	if (vlan > ADM_VLAN_MAX_ID)
+		return -EINVAL;
+
+	priv->pvid[port] = vlan;
+
+	return 0;
+}
+
+static int
+adm6996_get_pvid(struct switch_dev *dev, int port, int *vlan)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	dev_dbg (&priv->phydev->dev, "get_pvid port %d\n", port);
+	*vlan = priv->pvid[port];
+
+	return 0;
+}
+
+static int
+adm6996_set_vid(struct switch_dev *dev, const struct switch_attr *attr,
+		struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	dev_dbg (&priv->phydev->dev, "set_vid port %d vid %d\n", val->port_vlan,
+			val->value.i);
+
+	if (val->value.i > ADM_VLAN_MAX_ID)
+		return -EINVAL;
+
+	priv->vlan_id[val->port_vlan] = val->value.i;
+
+	return 0;
+};
+
+static int
+adm6996_get_vid(struct switch_dev *dev, const struct switch_attr *attr,
+		struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	dev_dbg (&priv->phydev->dev, "get_vid port %d\n", val->port_vlan);
+
+	val->value.i = priv->vlan_id[val->port_vlan];
+
+	return 0;
+};
+
+static int
+adm6996_get_ports(struct switch_dev *dev, struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+	u8 ports = priv->vlan_table[val->port_vlan];
+	u8 tagged = priv->vlan_tagged[val->port_vlan];
 	int i;
 
-	printk("%s: ADM6996 PHY driver attached.\n", pdev->attached_dev->name);
-	pdev->supported = ADVERTISED_100baseT_Full;
-	pdev->advertising = ADVERTISED_100baseT_Full;
+	dev_dbg (&priv->phydev->dev, "get_ports port_vlan %d\n",
+			val->port_vlan);
+
+	val->len = 0;
+
+	for (i = 0; i < ADM_NUM_PORTS; i++) {
+		struct switch_port *p;
+
+		if (!(ports & (1 << i)))
+			continue;
+
+		p = &val->value.ports[val->len++];
+		p->id = i;
+		if (tagged & (1 << i))
+			p->flags = (1 << SWITCH_PORT_FLAG_TAGGED);
+		else
+			p->flags = 0;
+	}
+
+	return 0;
+};
+
+static int
+adm6996_set_ports(struct switch_dev *dev, struct switch_val *val)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+	u8 *ports = &priv->vlan_table[val->port_vlan];
+	u8 *tagged = &priv->vlan_tagged[val->port_vlan];
+	int i;
+
+	dev_dbg (&priv->phydev->dev, "set_ports port_vlan %d ports",
+			val->port_vlan);
+
+	*ports = 0;
+	*tagged = 0;
+
+	for (i = 0; i < val->len; i++) {
+		struct switch_port *p = &val->value.ports[i];
+
+#ifdef DEBUG
+		pr_cont(" %d%s", p->id,
+		       ((p->flags & (1 << SWITCH_PORT_FLAG_TAGGED)) ? "T" :
+			""));
+#endif
+
+		if (p->flags & (1 << SWITCH_PORT_FLAG_TAGGED))
+			*tagged |= (1 << p->id);
+
+		*ports |= (1 << p->id);
+	}
+
+#ifdef DEBUG
+	pr_cont("\n");
+#endif
+
+	return 0;
+};
+
+/*
+ * Precondition: reg_mutex must be held
+ */
+static void
+adm6996_enable_vlan(struct adm6996_priv *priv)
+{
+	u16 reg;
+
+	reg = r16(priv->phydev, ADM_OTBE_P2_PVID);
+	reg &= ~(ADM_OTBE_MASK);
+	w16(priv->phydev, ADM_OTBE_P2_PVID, reg);
+	reg = r16(priv->phydev, ADM_IFNTE);
+	reg &= ~(ADM_IFNTE_MASK);
+	w16(priv->phydev, ADM_IFNTE, reg);
+	reg = r16(priv->phydev, ADM_VID_CHECK);
+	reg |= ADM_VID_CHECK_MASK;
+	w16(priv->phydev, ADM_VID_CHECK, reg);
+	reg = r16(priv->phydev, ADM_SYSC0);
+	reg |= ADM_NTTE;
+	reg &= ~(ADM_RVID1);
+	w16(priv->phydev, ADM_SYSC0, reg);
+	reg = r16(priv->phydev, ADM_SYSC3);
+	reg |= ADM_TBV;
+	w16(priv->phydev, ADM_SYSC3, reg);
+
+};
+
+/*
+ * Disable VLANs
+ *
+ * Sets VLAN mapping for port-based VLAN with all ports connected to
+ * eachother (this is also the power-on default).
+ *
+ * Precondition: reg_mutex must be held
+ */
+static void
+adm6996_disable_vlan(struct adm6996_priv *priv)
+{
+	u16 reg;
+	int i;
+
+	for (i = 0; i < ADM_NUM_PORTS; i++) {
+		reg = ADM_VLAN_FILT_MEMBER_MASK;
+		w16(priv->phydev, ADM_VLAN_FILT_L(i), reg);
+		reg = ADM_VLAN_FILT_VALID | ADM_VLAN_FILT_VID(1);
+		w16(priv->phydev, ADM_VLAN_FILT_H(i), reg);
+	}
+
+	reg = r16(priv->phydev, ADM_OTBE_P2_PVID);
+	reg |= ADM_OTBE_MASK;
+	w16(priv->phydev, ADM_OTBE_P2_PVID, reg);
+	reg = r16(priv->phydev, ADM_IFNTE);
+	reg |= ADM_IFNTE_MASK;
+	w16(priv->phydev, ADM_IFNTE, reg);
+	reg = r16(priv->phydev, ADM_VID_CHECK);
+	reg &= ~(ADM_VID_CHECK_MASK);
+	w16(priv->phydev, ADM_VID_CHECK, reg);
+	reg = r16(priv->phydev, ADM_SYSC0);
+	reg &= ~(ADM_NTTE);
+	reg |= ADM_RVID1;
+	w16(priv->phydev, ADM_SYSC0, reg);
+	reg = r16(priv->phydev, ADM_SYSC3);
+	reg &= ~(ADM_TBV);
+	w16(priv->phydev, ADM_SYSC3, reg);
+}
+
+/*
+ * Precondition: reg_mutex must be held
+ */
+static void
+adm6996_apply_port_pvids(struct adm6996_priv *priv)
+{
+	u16 reg;
+	int i;
+
+	for (i = 0; i < ADM_NUM_PORTS; i++) {
+		reg = r16(priv->phydev, adm_portcfg[i]);
+		reg &= ~(ADM_PORTCFG_PVID_MASK);
+		reg |= ADM_PORTCFG_PVID(priv->pvid[i]);
+		w16(priv->phydev, adm_portcfg[i], reg);
+	}
+
+	w16(priv->phydev, ADM_P0_PVID, ADM_P0_PVID_VAL(priv->pvid[0]));
+	w16(priv->phydev, ADM_P1_PVID, ADM_P1_PVID_VAL(priv->pvid[1]));
+	reg = r16(priv->phydev, ADM_OTBE_P2_PVID);
+	reg &= ~(ADM_P2_PVID_MASK);
+	reg |= ADM_P2_PVID_VAL(priv->pvid[2]);
+	w16(priv->phydev, ADM_OTBE_P2_PVID, reg);
+	reg = ADM_P3_PVID_VAL(priv->pvid[3]);
+	reg |= ADM_P4_PVID_VAL(priv->pvid[4]);
+	w16(priv->phydev, ADM_P3_P4_PVID, reg);
+	w16(priv->phydev, ADM_P5_PVID, ADM_P5_PVID_VAL(priv->pvid[5]));
+}
+
+/*
+ * Precondition: reg_mutex must be held
+ */
+static void
+adm6996_apply_vlan_filters(struct adm6996_priv *priv)
+{
+	u8 ports, tagged;
+	u16 vid, reg;
+	int i;
+
+	for (i = 0; i < ADM_NUM_VLANS; i++) {
+		vid = priv->vlan_id[i];
+		ports = priv->vlan_table[i];
+		tagged = priv->vlan_tagged[i];
+
+		if (ports == 0) {
+			/* Disable VLAN entry */
+			w16(priv->phydev, ADM_VLAN_FILT_H(i), 0);
+			w16(priv->phydev, ADM_VLAN_FILT_L(i), 0);
+			continue;
+		}
+
+		reg = ADM_VLAN_FILT_MEMBER(ports);
+		reg |= ADM_VLAN_FILT_TAGGED(tagged);
+		w16(priv->phydev, ADM_VLAN_FILT_L(i), reg);
+		reg = ADM_VLAN_FILT_VALID | ADM_VLAN_FILT_VID(vid);
+		w16(priv->phydev, ADM_VLAN_FILT_H(i), reg);
+	}
+}
+
+static int
+adm6996_hw_apply(struct switch_dev *dev)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	dev_dbg(&priv->phydev->dev, "hw_apply\n");
+
+	mutex_lock(&priv->reg_mutex);
+
+	if (!priv->enable_vlan) {
+		if (priv->vlan_enabled) {
+			adm6996_disable_vlan(priv);
+			priv->vlan_enabled = 0;
+		}
+		goto out;
+	}
+
+	if (!priv->vlan_enabled) {
+		adm6996_enable_vlan(priv);
+		priv->vlan_enabled = 1;
+	}
+
+	adm6996_apply_port_pvids(priv);
+	adm6996_apply_vlan_filters(priv);
+
+out:
+	mutex_unlock(&priv->reg_mutex);
+
+	return 0;
+}
+
+/*
+ * Reset the switch
+ *
+ * The ADM6996 can't do a software-initiated reset, so we just initialise the
+ * registers we support in this driver.
+ *
+ * Precondition: reg_mutex must be held
+ */
+static void
+adm6996_perform_reset (struct adm6996_priv *priv)
+{
+	int i;
 
 	/* initialize port and vlan settings */
-	for (i = 0; i < ADM_PHY_PORTS; i++) {
-		w16(pdev, adm_portcfg[i], ADM_PORTCFG_INIT |
-			ADM_PORTCFG_PVID((i == ADM_WAN_PORT) ? 1 : 0));
+	for (i = 0; i < ADM_NUM_PORTS - 1; i++) {
+		w16(priv->phydev, adm_portcfg[i], ADM_PORTCFG_INIT |
+			ADM_PORTCFG_PVID(0));
 	}
-	w16(pdev, adm_portcfg[5], ADM_PORTCFG_CPU);
+	w16(priv->phydev, adm_portcfg[5], ADM_PORTCFG_CPU);
 
-	/* reset all ports */
+	/* reset all PHY ports */
 	for (i = 0; i < ADM_PHY_PORTS; i++) {
-		w16(pdev, ADM_PHY_PORT(i), ADM_PHYCFG_INIT);
+		w16(priv->phydev, ADM_PHY_PORT(i), ADM_PHYCFG_INIT);
+	}
+
+	priv->enable_vlan = 0;
+	priv->vlan_enabled = 0;
+
+	for (i = 0; i < ADM_NUM_PORTS; i++) {
+		priv->pvid[i] = 0;
+	}
+
+	for (i = 0; i < ADM_NUM_VLANS; i++) {
+		priv->vlan_id[i] = i;
+		priv->vlan_table[i] = 0;
+		priv->vlan_tagged[i] = 0;
+	}
+
+	if (priv->model == ADM6996M) {
+		/* Clear VLAN priority map so prio's are unused */
+		w16 (priv->phydev, ADM_VLAN_PRIOMAP, 0);
+
+		adm6996_disable_vlan(priv);
+		adm6996_apply_port_pvids(priv);
+	}
+}
+
+static int
+adm6996_reset_switch(struct switch_dev *dev)
+{
+	struct adm6996_priv *priv = to_adm(dev);
+
+	dev_dbg (&priv->phydev->dev, "reset\n");
+	mutex_lock(&priv->reg_mutex);
+	adm6996_perform_reset (priv);
+	mutex_unlock(&priv->reg_mutex);
+	return 0;
+}
+
+static struct switch_attr adm6996_globals[] = {
+	{
+	 .type = SWITCH_TYPE_INT,
+	 .name = "enable_vlan",
+	 .description = "Enable VLANs",
+	 .set = adm6996_set_enable_vlan,
+	 .get = adm6996_get_enable_vlan,
+	},
+#ifdef DEBUG
+	{
+	 .type = SWITCH_TYPE_INT,
+	 .name = "addr",
+	 .description =
+	 "Direct register access: set register address (0 - 1023)",
+	 .set = adm6996_set_addr,
+	 .get = adm6996_get_addr,
+	 },
+	{
+	 .type = SWITCH_TYPE_INT,
+	 .name = "data",
+	 .description =
+	 "Direct register access: read/write to register (0 - 65535)",
+	 .set = adm6996_set_data,
+	 .get = adm6996_get_data,
+	 },
+#endif /* def DEBUG */
+};
+
+static struct switch_attr adm6996_port[] = {
+};
+
+static struct switch_attr adm6996_vlan[] = {
+	{
+	 .type = SWITCH_TYPE_INT,
+	 .name = "vid",
+	 .description = "VLAN ID",
+	 .set = adm6996_set_vid,
+	 .get = adm6996_get_vid,
+	 },
+};
+
+static const struct switch_dev_ops adm6996_ops = {
+	.attr_global = {
+			.attr = adm6996_globals,
+			.n_attr = ARRAY_SIZE(adm6996_globals),
+			},
+	.attr_port = {
+		      .attr = adm6996_port,
+		      .n_attr = ARRAY_SIZE(adm6996_port),
+		      },
+	.attr_vlan = {
+		      .attr = adm6996_vlan,
+		      .n_attr = ARRAY_SIZE(adm6996_vlan),
+		      },
+	.get_port_pvid = adm6996_get_pvid,
+	.set_port_pvid = adm6996_set_pvid,
+	.get_vlan_ports = adm6996_get_ports,
+	.set_vlan_ports = adm6996_set_ports,
+	.apply_config = adm6996_hw_apply,
+	.reset_switch = adm6996_reset_switch,
+};
+
+static int adm6996_config_init(struct phy_device *pdev)
+{
+	struct adm6996_priv *priv;
+	struct switch_dev *swdev;
+
+	int ret;
+	u16 test, old;
+
+	pdev->supported = ADVERTISED_100baseT_Full;
+	pdev->advertising = ADVERTISED_100baseT_Full;
+
+	if (pdev->addr != 0) {
+		pr_info ("%s: PHY overlaps ADM6996, providing fixed PHY 0x%x.\n"
+				, pdev->attached_dev->name, pdev->addr);
+		return 0;
+	}
+
+	priv = kzalloc(sizeof(struct adm6996_priv), GFP_KERNEL);
+	if (priv == NULL)
+		return -ENOMEM;
+
+	mutex_init(&priv->reg_mutex);
+	priv->phydev = pdev;
+	priv->read = adm6996_read_mii_reg;
+	priv->write = adm6996_write_mii_reg;
+	pdev->priv = priv;
+
+	/* Detect type of chip */
+	old = r16(pdev, ADM_VID_CHECK);
+	test = old ^ (1 << 12);
+	w16(pdev, ADM_VID_CHECK, test);
+	test ^= r16(pdev, ADM_VID_CHECK);
+	if (test & (1 << 12)) {
+		/* 
+		 * Bit 12 of this register is read-only. 
+		 * This is the FC model. 
+		 */
+		priv->model = ADM6996FC;
+	} else {
+		/* Bit 12 is read-write. This is the M model. */
+		priv->model = ADM6996M;
+		w16(pdev, ADM_VID_CHECK, old);
+	}
+
+	swdev = &priv->dev;
+	swdev->name = (adm6996_model_name[priv->model]);
+	swdev->cpu_port = ADM_CPU_PORT;
+	swdev->ports = ADM_NUM_PORTS;
+	swdev->vlans = ADM_NUM_VLANS;
+	swdev->ops = &adm6996_ops;
+
+	pr_info ("%s: %s model PHY found.\n", pdev->attached_dev->name,
+			swdev->name);
+
+	mutex_lock(&priv->reg_mutex);
+	adm6996_perform_reset (priv);
+	mutex_unlock(&priv->reg_mutex);
+
+	if (priv->model == ADM6996M) {
+		if ((ret = register_switch(swdev, pdev->attached_dev)) < 0) {
+			kfree(priv);
+			return ret;
+		}
 	}
 
 	return 0;
 }
 
+/*
+ * Warning: phydev->priv is NULL if phydev->addr != 0
+ */
 static int adm6996_read_status(struct phy_device *phydev)
 {
 	phydev->speed = SPEED_100;
@@ -100,6 +662,9 @@ static int adm6996_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+/*
+ * Warning: phydev->priv is NULL if phydev->addr != 0
+ */
 static int adm6996_config_aneg(struct phy_device *phydev)
 {
 	return 0;
@@ -110,6 +675,10 @@ static int adm6996_fixup(struct phy_device *dev)
 	struct mii_bus *bus = dev->bus;
 	u16 reg;
 
+	/* Our custom registers are at PHY addresses 0-10. Claim those. */
+	if (dev->addr > 10)
+		return 0;
+
 	/* look for the switch on the bus */
 	reg = bus->read(bus, PHYADDR(ADM_SIG0)) & ADM_SIG0_MASK;
 	if (reg != ADM_SIG0_VAL)
@@ -120,26 +689,23 @@ static int adm6996_fixup(struct phy_device *dev)
 		return 0;
 
 	dev->phy_id = (ADM_SIG0_VAL << 16) | ADM_SIG1_VAL;
+
 	return 0;
 }
 
 static int adm6996_probe(struct phy_device *pdev)
 {
-	struct adm6996_priv *priv;
-
-	priv = kzalloc(sizeof(struct adm6996_priv), GFP_KERNEL);
-	if (priv == NULL)
-		return -ENOMEM;
-
-	priv->read = adm6996_read_mii_reg;
-	priv->write = adm6996_write_mii_reg;
-	pdev->priv = priv;
 	return 0;
 }
 
 static void adm6996_remove(struct phy_device *pdev)
 {
-	kfree(pdev->priv);
+	struct adm6996_priv *priv = phy_to_adm(pdev);
+
+	if (priv != NULL && priv->model == ADM6996M)
+		unregister_switch(&priv->dev);
+
+	kfree(priv);
 }
 
 

target/linux/generic/files/drivers/net/phy/adm6996.h

@@ -2,6 +2,7 @@
  * ADM6996 switch driver
  *
  * Copyright (c) 2008 Felix Fietkau <[email protected]>
+ * Copyright (c) 2010,2011 Peter Lebbing <[email protected]>
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of the GNU General Public License v2 as published by the
@@ -10,9 +11,17 @@
 #ifndef __ADM6996_H
 #define __ADM6996_H
 
-#define ADM_PHY_PORTS	5
+/*
+ * ADM_PHY_PORTS: Number of ports with a PHY.
+ * We only control ports 0 to 3, because if 4 is connected, it is most likely
+ * not connected to the switch but to a separate MII and MAC for the WAN port.
+ */
+#define ADM_PHY_PORTS	4
+#define ADM_NUM_PORTS	6
 #define ADM_CPU_PORT	5
-#define ADM_WAN_PORT	0 /* FIXME: dynamic ? */
+
+#define ADM_NUM_VLANS 16
+#define ADM_VLAN_MAX_ID 4094
 
 enum admreg {
 	ADM_EEPROM_BASE		= 0x0,
@@ -22,7 +31,21 @@ enum admreg {
 		ADM_P3_CFG		= ADM_EEPROM_BASE + 7,
 		ADM_P4_CFG		= ADM_EEPROM_BASE + 8,
 		ADM_P5_CFG		= ADM_EEPROM_BASE + 9,
+		ADM_SYSC0		= ADM_EEPROM_BASE + 0xa,
+		ADM_VLAN_PRIOMAP	= ADM_EEPROM_BASE + 0xe,
+		ADM_SYSC3		= ADM_EEPROM_BASE + 0x11,
+		/* Input Force No Tag Enable */
+		ADM_IFNTE		= ADM_EEPROM_BASE + 0x20,
+		ADM_VID_CHECK		= ADM_EEPROM_BASE + 0x26,
+		ADM_P0_PVID		= ADM_EEPROM_BASE + 0x28,
+		ADM_P1_PVID		= ADM_EEPROM_BASE + 0x29,
+		/* Output Tag Bypass Enable and P2 PVID */
+		ADM_OTBE_P2_PVID	= ADM_EEPROM_BASE + 0x2a,
+		ADM_P3_P4_PVID		= ADM_EEPROM_BASE + 0x2b,
+		ADM_P5_PVID		= ADM_EEPROM_BASE + 0x2c,
 	ADM_EEPROM_EXT_BASE	= 0x40,
+#define ADM_VLAN_FILT_L(n) (ADM_EEPROM_EXT_BASE + 2 * (n))
+#define ADM_VLAN_FILT_H(n) (ADM_EEPROM_EXT_BASE + 1 + 2 * (n))
 	ADM_COUNTER_BASE	= 0xa0,
 		ADM_SIG0		= ADM_COUNTER_BASE + 0,
 		ADM_SIG1		= ADM_COUNTER_BASE + 1,
@@ -31,8 +54,8 @@ enum admreg {
 };
 
 /* Chip identification patterns */
-#define	ADM_SIG0_MASK	0xfff0
-#define ADM_SIG0_VAL	0x1020
+#define	ADM_SIG0_MASK	0xffff
+#define ADM_SIG0_VAL	0x1023
 #define ADM_SIG1_MASK	0xffff
 #define ADM_SIG1_VAL	0x0007
 
@@ -84,8 +107,32 @@ enum {
 	),
 };
 
-#define ADM_PORTCFG_PPID(N) ((n & 0x3) << 8)
+#define ADM_PORTCFG_PPID(n) ((n & 0x3) << 8)
 #define ADM_PORTCFG_PVID(n) ((n & 0xf) << 10)
+#define ADM_PORTCFG_PVID_MASK (0xf << 10)
+
+#define ADM_IFNTE_MASK (0x3f << 9)
+#define ADM_VID_CHECK_MASK (0x3f << 6)
+
+#define ADM_P0_PVID_VAL(n) ((((n) & 0xff0) >> 4) << 0)
+#define ADM_P1_PVID_VAL(n) ((((n) & 0xff0) >> 4) << 0)
+#define ADM_P2_PVID_VAL(n) ((((n) & 0xff0) >> 4) << 0)
+#define ADM_P3_PVID_VAL(n) ((((n) & 0xff0) >> 4) << 0)
+#define ADM_P4_PVID_VAL(n) ((((n) & 0xff0) >> 4) << 8)
+#define ADM_P5_PVID_VAL(n) ((((n) & 0xff0) >> 4) << 0)
+#define ADM_P2_PVID_MASK 0xff
+
+#define ADM_OTBE(n) (((n) & 0x3f) << 8)
+#define ADM_OTBE_MASK (0x3f << 8)
+
+/* ADM_SYSC0 */
+enum {
+	ADM_NTTE	= (1 << 2),	/* New Tag Transmit Enable */
+	ADM_RVID1	= (1 << 8)	/* Replace VLAN ID 1 */
+};
+
+/* Tag Based VLAN in ADM_SYSC3 */
+#define ADM_TBV (1 << 5)
 
 static const u8 adm_portcfg[] = {
 	[0] = ADM_P0_CFG,
@@ -96,6 +143,16 @@ static const u8 adm_portcfg[] = {
 	[5] = ADM_P5_CFG,
 };
 
+/* Fields in ADM_VLAN_FILT_L(x) */
+#define ADM_VLAN_FILT_FID(n) (((n) & 0xf) << 12)
+#define ADM_VLAN_FILT_TAGGED(n) (((n) & 0x3f) << 6)
+#define ADM_VLAN_FILT_MEMBER(n) (((n) & 0x3f) << 0)
+#define ADM_VLAN_FILT_MEMBER_MASK 0x3f
+/* Fields in ADM_VLAN_FILT_H(x) */
+#define ADM_VLAN_FILT_VALID (1 << 15)
+#define ADM_VLAN_FILT_VID(n) (((n) & 0xfff) << 0)
+
+
 /*
  * Split the register address in phy id and register
  * it will get combined again by the mdio bus op

target/linux/generic/patches-2.6.30/620-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -82,6 +82,11 @@ config LSI_ET1011C_PHY
+@@ -82,6 +82,13 @@ config LSI_ET1011C_PHY
  	---help---
  	  Supports the LSI ET1011C PHY.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"

target/linux/generic/patches-2.6.31/620-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -82,6 +82,11 @@ config LSI_ET1011C_PHY
+@@ -82,6 +82,13 @@ config LSI_ET1011C_PHY
  	---help---
  	  Supports the LSI ET1011C PHY.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"

target/linux/generic/patches-2.6.32/620-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -88,6 +88,11 @@ config LSI_ET1011C_PHY
+@@ -88,6 +88,13 @@ config LSI_ET1011C_PHY
  	---help---
  	  Supports the LSI ET1011C PHY.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"

target/linux/generic/patches-2.6.36/620-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -93,6 +93,11 @@ config MICREL_PHY
+@@ -93,6 +93,13 @@ config MICREL_PHY
  	---help---
  	  Supports the KSZ9021, VSC8201, KS8001 PHYs.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"

target/linux/generic/patches-2.6.37/720-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -98,6 +98,11 @@ config MICREL_PHY
+@@ -98,6 +98,13 @@ config MICREL_PHY
  	---help---
  	  Supports the KSZ9021, VSC8201, KS8001 PHYs.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"

target/linux/generic/patches-2.6.38/720-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -98,6 +98,11 @@ config MICREL_PHY
+@@ -98,6 +98,13 @@ config MICREL_PHY
  	---help---
  	  Supports the KSZ9021, VSC8201, KS8001 PHYs.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"

target/linux/generic/patches-2.6.39/720-phy_adm6996.patch

@@ -1,13 +1,15 @@
 --- a/drivers/net/phy/Kconfig
 +++ b/drivers/net/phy/Kconfig
-@@ -97,6 +97,11 @@ config MICREL_PHY
+@@ -97,6 +97,13 @@ config MICREL_PHY
  	---help---
  	  Supports the KSZ9021, VSC8201, KS8001 PHYs.
  
 +config ADM6996_PHY
 +	tristate "Driver for ADM6996 switches"
++	select SWCONFIG
 +	---help---
-+	  Currently supports the ADM6996F switch
++	  Currently supports the ADM6996FC and ADM6996M switches.
++	  Support for FC is very limited.
 +
  config FIXED_PHY
  	bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"