ramips: update i2c drivers

* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <[email protected]>

target/linux/ramips/patches-4.4/0044-i2c-MIPS-adds-ralink-I2C-driver.patch

@@ -45,12 +45,13 @@ Signed-off-by: John Crispin <[email protected]>
 +};
 --- a/drivers/i2c/busses/Kconfig
 +++ b/drivers/i2c/busses/Kconfig
-@@ -806,6 +806,10 @@ config I2C_RK3X
+@@ -806,6 +806,11 @@ config I2C_RK3X
  	  This driver can also be built as a module. If so, the module will
  	  be called i2c-rk3x.
  
 +config I2C_RALINK
 +	tristate "Ralink I2C Controller"
++	depends on RALINK && !SOC_MT7621
 +	select OF_I2C
 +
  config HAVE_S3C2410_I2C
@@ -68,11 +69,12 @@ Signed-off-by: John Crispin <[email protected]>
  obj-$(CONFIG_I2C_RK3X)		+= i2c-rk3x.o
 --- /dev/null
 +++ b/drivers/i2c/busses/i2c-ralink.c
-@@ -0,0 +1,327 @@
+@@ -0,0 +1,435 @@
 +/*
 + * drivers/i2c/busses/i2c-ralink.c
 + *
 + * Copyright (C) 2013 Steven Liu <[email protected]>
++ * Copyright (C) 2016 Michael Lee <[email protected]>
 + *
 + * Improve driver for i2cdetect from i2c-tools to detect i2c devices on the bus.
 + * (C) 2014 Sittisak <[email protected]>
@@ -101,8 +103,7 @@ Signed-off-by: John Crispin <[email protected]>
 +#include <linux/i2c.h>
 +#include <linux/io.h>
 +#include <linux/err.h>
-+
-+#include <asm/mach-ralink/ralink_regs.h>
++#include <linux/clk.h>
 +
 +#define REG_CONFIG_REG		0x00
 +#define REG_CLKDIV_REG		0x04
@@ -113,191 +114,250 @@ Signed-off-by: John Crispin <[email protected]>
 +#define REG_STATUS_REG		0x18
 +#define REG_STARTXFR_REG	0x1C
 +#define REG_BYTECNT_REG		0x20
-+#define REG_SM0CFG2		0x28
-+#define REG_SM0CTL0		0x40
 +
++/* REG_CONFIG_REG */
++#define I2C_ADDRLEN_OFFSET	5
++#define I2C_DEVADLEN_OFFSET	2
++#define I2C_ADDRLEN_MASK	0x3
++#define I2C_ADDR_DIS		BIT(1)
++#define I2C_DEVADDR_DIS		BIT(0)
++#define I2C_ADDRLEN_8		(7 << I2C_ADDRLEN_OFFSET)
++#define I2C_DEVADLEN_7		(6 << I2C_DEVADLEN_OFFSET)
++#define I2C_CONF_DEFAULT	(I2C_ADDRLEN_8 | I2C_DEVADLEN_7)
++
++/* REG_CLKDIV_REG */
++#define I2C_CLKDIV_MASK		0xffff
++
++/* REG_DEVADDR_REG */
++#define I2C_DEVADDR_MASK	0x7f
++
++/* REG_ADDR_REG */
++#define I2C_ADDR_MASK		0xff
++
++/* REG_STATUS_REG */
 +#define I2C_STARTERR		BIT(4)
 +#define I2C_ACKERR		BIT(3)
 +#define I2C_DATARDY		BIT(2)
 +#define I2C_SDOEMPTY		BIT(1)
 +#define I2C_BUSY		BIT(0)
 +
-+#define I2C_DEVADLEN_7		(6 << 2)
-+#define I2C_ADDRDIS		BIT(1)
++/* REG_STARTXFR_REG */
++#define NOSTOP_CMD		BIT(2)
++#define NODATA_CMD		BIT(1)
++#define READ_CMD		BIT(0)
 +
-+#define CLKDIV_VALUE		200 // clock rate is 40M, 40M / (200*2) = 100k (standard i2c bus rate).
-+//#define CLKDIV_VALUE		50 // clock rate is 40M, 40M / (50*2) = 400k (fast i2c bus rate).
-+
-+#define READ_CMD		0x01
-+#define WRITE_CMD		0x00
-+#define READ_BLOCK              64
-+
-+#define SM0CTL0_OD		BIT(31)
-+#define SM0CTL0_VTRIG		BIT(28)
-+#define SM0CTL0_OUTHI		BIT(6)
-+#define SM0CTL0_STRETCH		BIT(1)
-+#define SM0CTL0_DEFAULT		(SM0CTL0_OD | SM0CTL0_VTRIG | SM0CTL0_OUTHI | SM0CTL0_STRETCH)
++/* REG_BYTECNT_REG */
++#define BYTECNT_MAX		64
++#define SET_BYTECNT(x)		(x - 1)
 +
 +/* timeout waiting for I2C devices to respond (clock streching) */
-+#define RT_I2C_TIMEOUT (msecs_to_jiffies(1000))
-+
-+enum {
-+	I2C_TYPE_RALINK,
-+	I2C_TYPE_MEDIATEK,
++#define TIMEOUT_MS              1000
++#define DELAY_INTERVAL_US       100
++
++struct rt_i2c {
++	void __iomem *base;
++	struct clk *clk;
++	struct device *dev;
++	struct i2c_adapter adap;
++	u32 cur_clk;
++	u32 clk_div;
++	u32 flags;
 +};
 +
-+static void __iomem *membase;
-+static struct i2c_adapter *adapter;
-+static int hw_type;
-+
-+static void rt_i2c_w32(u32 val, unsigned reg)
++static void rt_i2c_w32(struct rt_i2c *i2c, u32 val, unsigned reg)
 +{
-+	iowrite32(val, membase + reg);
++	iowrite32(val, i2c->base + reg);
 +}
 +
-+static u32 rt_i2c_r32(unsigned reg)
++static u32 rt_i2c_r32(struct rt_i2c *i2c, unsigned reg)
 +{
-+	return ioread32(membase + reg);
++	return ioread32(i2c->base + reg);
 +}
 +
-+static inline int rt_i2c_get_ack(void)
++static int poll_down_timeout(void __iomem *addr, u32 mask)
 +{
-+        return (rt_i2c_r32(REG_STATUS_REG) & I2C_ACKERR) ? -EIO : 0;
-+}
-+
-+static inline int rt_i2c_wait_rx_done(void)
-+{
-+	unsigned long timeout;
-+
-+	timeout = jiffies + RT_I2C_TIMEOUT;
++	unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
 +
 +	do {
-+		if (time_after(jiffies, timeout))
-+			return (-ETIMEDOUT);
++		if (!(readl_relaxed(addr) & mask))
++			return 0;
 +
-+	} while (!(rt_i2c_r32(REG_STATUS_REG) & I2C_DATARDY));
++		usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
++	} while (time_before(jiffies, timeout));
 +
-+	return 0;
++	return (readl_relaxed(addr) & mask) ? -EAGAIN : 0;
 +}
 +
-+static inline int rt_i2c_wait_idle(void)
++static int rt_i2c_wait_idle(struct rt_i2c *i2c)
 +{
-+	unsigned long timeout;
++	int ret;
 +
-+	timeout = jiffies + RT_I2C_TIMEOUT;
++	ret = poll_down_timeout(i2c->base + REG_STATUS_REG, I2C_BUSY);
++	if (ret < 0)
++		dev_dbg(i2c->dev, "idle err(%d)\n", ret);
 +
-+	do {
-+		if (time_after(jiffies, timeout)) {
-+			printk("i2c-read line busy\n");
-+			return 1;
-+		}
-+	} while (rt_i2c_r32(REG_STATUS_REG) & I2C_BUSY);
-+
-+	return 0;
++	return ret;
 +}
 +
-+static inline int rt_i2c_wait_tx_done(void)
++static int poll_up_timeout(void __iomem *addr, u32 mask)
 +{
-+	unsigned long timeout;
-+
-+	timeout = jiffies + RT_I2C_TIMEOUT;
++	unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
++	u32 status;
 +
 +	do {
-+		if (time_after(jiffies, timeout))
-+			return (-ETIMEDOUT);
++		status = readl_relaxed(addr);
 +
-+	} while (!(rt_i2c_r32(REG_STATUS_REG) & I2C_SDOEMPTY));
++		/* check error status */
++		if (status & I2C_STARTERR)
++			return -EAGAIN;
++		else if (status & I2C_ACKERR)
++			return -ENXIO;
++		else if (status & mask)
++			return 0;
 +
-+	return 0;
++		usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
++	} while (time_before(jiffies, timeout));
++
++	return -ETIMEDOUT;
 +}
 +
-+static int rt_i2c_handle_msg(struct i2c_adapter *a, struct i2c_msg* msg)
++static int rt_i2c_wait_rx_done(struct rt_i2c *i2c)
 +{
-+	int i = 0, j = 0, pos = 0;
-+	int nblock = msg->len / READ_BLOCK;
-+        int rem = msg->len % READ_BLOCK;
-+	int ret = 0;
-+
-+	if (msg->flags & I2C_M_TEN) {
-+		printk("10 bits addr not supported\n");
-+		return -EINVAL;
-+	}
-+
-+	if (msg->flags & I2C_M_RD) {
-+		for (i = 0; i < nblock; i++) {
-+	                if (rt_i2c_wait_idle())
-+				return -ETIMEDOUT;
-+			rt_i2c_w32(READ_BLOCK - 1, REG_BYTECNT_REG);
-+			rt_i2c_w32(READ_CMD, REG_STARTXFR_REG);
-+			for (j = 0; j < READ_BLOCK; j++) {
-+				if (rt_i2c_wait_rx_done() < 0)
-+					ret = rt_i2c_wait_rx_done();
-+                                if (rt_i2c_get_ack() < 0)
-+					ret = rt_i2c_get_ack();
-+				msg->buf[pos++] = rt_i2c_r32(REG_DATAIN_REG);
-+			}
-+		}
-+
-+		if (rt_i2c_wait_idle())
-+			return -ETIMEDOUT;
-+		if (rem) {
-+			rt_i2c_w32(rem - 1, REG_BYTECNT_REG);
-+			rt_i2c_w32(READ_CMD, REG_STARTXFR_REG);
-+		}
-+		for (i = 0; i < rem; i++) {
-+			if (rt_i2c_wait_rx_done() < 0)
-+				ret = rt_i2c_wait_rx_done();
-+                        if (rt_i2c_get_ack() < 0)
-+				ret = rt_i2c_get_ack();
++	int ret;
 +
-+			msg->buf[pos++] = rt_i2c_r32(REG_DATAIN_REG);
-+		}
-+	} else {
-+		if (rt_i2c_wait_idle())
-+			return -ETIMEDOUT;
-+		rt_i2c_w32(msg->len - 1, REG_BYTECNT_REG);
-+		for (i = 0; i < msg->len; i++) {
-+			rt_i2c_w32(msg->buf[i], REG_DATAOUT_REG);
-+			rt_i2c_w32(WRITE_CMD, REG_STARTXFR_REG);
-+
-+			if (rt_i2c_wait_tx_done() < 0)
-+				ret = rt_i2c_wait_tx_done();
-+                        if (rt_i2c_get_ack() < 0)
-+				ret = rt_i2c_get_ack();
-+		}
-+	}
++	ret = poll_up_timeout(i2c->base + REG_STATUS_REG, I2C_DATARDY);
++	if (ret < 0)
++		dev_dbg(i2c->dev, "rx err(%d)\n", ret);
 +
 +	return ret;
 +}
 +
-+static int rt_i2c_master_xfer(struct i2c_adapter *a, struct i2c_msg *m, int n)
++static int rt_i2c_wait_tx_done(struct rt_i2c *i2c)
 +{
-+	int i = 0;
-+	int ret = 0;
++	int ret;
 +
-+	if (rt_i2c_wait_idle())
-+		return -ETIMEDOUT;
++	ret = poll_up_timeout(i2c->base + REG_STATUS_REG, I2C_SDOEMPTY);
++	if (ret < 0)
++		dev_dbg(i2c->dev, "tx err(%d)\n", ret);
 +
-+	device_reset(a->dev.parent);
++	return ret;
++}
 +
-+	rt_i2c_w32(m->addr, REG_DEVADDR_REG);
-+	rt_i2c_w32(I2C_DEVADLEN_7 | I2C_ADDRDIS, REG_CONFIG_REG);
-+	if (hw_type == I2C_TYPE_RALINK) {
-+		rt_i2c_w32(CLKDIV_VALUE, REG_CLKDIV_REG);
-+	} else {
-+		rt_i2c_w32((CLKDIV_VALUE << 16) | SM0CTL0_DEFAULT, REG_SM0CTL0);
-+		rt_i2c_w32(1, REG_SM0CFG2);
-+	}
++static void rt_i2c_reset(struct rt_i2c *i2c)
++{
++	device_reset(i2c->adap.dev.parent);
++	barrier();
++	rt_i2c_w32(i2c, i2c->clk_div, REG_CLKDIV_REG);
++}
++
++static void rt_i2c_dump_reg(struct rt_i2c *i2c)
++{
++	dev_dbg(i2c->dev, "conf %08x, clkdiv %08x, devaddr %08x, " \
++			"addr %08x, dataout %08x, datain %08x, " \
++			"status %08x, startxfr %08x, bytecnt %08x\n",
++			rt_i2c_r32(i2c, REG_CONFIG_REG),
++			rt_i2c_r32(i2c, REG_CLKDIV_REG),
++			rt_i2c_r32(i2c, REG_DEVADDR_REG),
++			rt_i2c_r32(i2c, REG_ADDR_REG),
++			rt_i2c_r32(i2c, REG_DATAOUT_REG),
++			rt_i2c_r32(i2c, REG_DATAIN_REG),
++			rt_i2c_r32(i2c, REG_STATUS_REG),
++			rt_i2c_r32(i2c, REG_STARTXFR_REG),
++			rt_i2c_r32(i2c, REG_BYTECNT_REG));
++}
 +
-+	for (i = 0; i < n && !ret; i++) {
-+		ret = rt_i2c_handle_msg(a, &m[i]);
++static int rt_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
++		int num)
++{
++	struct rt_i2c *i2c;
++	struct i2c_msg *pmsg;
++	unsigned char addr;
++	int i, j, ret;
++	u32 cmd;
++
++	i2c = i2c_get_adapdata(adap);
++
++	for (i = 0; i < num; i++) {
++		pmsg = &msgs[i];
++		if (i == (num - 1))
++			cmd = 0;
++		else
++			cmd = NOSTOP_CMD;
++
++		dev_dbg(i2c->dev, "addr: 0x%x, len: %d, flags: 0x%x, stop: %d\n",
++				pmsg->addr, pmsg->len, pmsg->flags,
++				(cmd == 0)? 1 : 0);
++
++		/* wait hardware idle */
++		if ((ret = rt_i2c_wait_idle(i2c)))
++			goto err_timeout;
++
++		if (pmsg->flags & I2C_M_TEN) {
++			rt_i2c_w32(i2c, I2C_CONF_DEFAULT, REG_CONFIG_REG);
++			/* 10 bits address */
++			addr = 0x78 | ((pmsg->addr >> 8) & 0x03);
++			rt_i2c_w32(i2c, addr & I2C_DEVADDR_MASK,
++					REG_DEVADDR_REG);
++			rt_i2c_w32(i2c, pmsg->addr & I2C_ADDR_MASK,
++					REG_ADDR_REG);
++		} else {
++			rt_i2c_w32(i2c, I2C_CONF_DEFAULT | I2C_ADDR_DIS,
++					REG_CONFIG_REG);
++			/* 7 bits address */
++			rt_i2c_w32(i2c, pmsg->addr & I2C_DEVADDR_MASK,
++					REG_DEVADDR_REG);
++		}
 +
-+		if (ret < 0) {
-+			return ret;
++		/* buffer length */
++		if (pmsg->len == 0)
++			cmd |= NODATA_CMD;
++		else
++			rt_i2c_w32(i2c, SET_BYTECNT(pmsg->len),
++					REG_BYTECNT_REG);
++
++		j = 0;
++		if (pmsg->flags & I2C_M_RD) {
++			cmd |= READ_CMD;
++			/* start transfer */
++			barrier();
++			rt_i2c_w32(i2c, cmd, REG_STARTXFR_REG);
++			do {
++				/* wait */
++				if ((ret = rt_i2c_wait_rx_done(i2c)))
++					goto err_timeout;
++				/* read data */
++				if (pmsg->len)
++					pmsg->buf[j] = rt_i2c_r32(i2c,
++							REG_DATAIN_REG);
++				j++;
++			} while (j < pmsg->len);
++		} else {
++			do {
++				/* write data */
++				if (pmsg->len)
++					rt_i2c_w32(i2c, pmsg->buf[j],
++							REG_DATAOUT_REG);
++				/* start transfer */
++				if (j == 0) {
++					barrier();
++					rt_i2c_w32(i2c, cmd, REG_STARTXFR_REG);
++				}
++				/* wait */
++				if ((ret = rt_i2c_wait_tx_done(i2c)))
++					goto err_timeout;
++				j++;
++			} while (j < pmsg->len);
 +		}
 +	}
++	/* the return value is number of executed messages */
++	ret = i;
++
++	return ret;
 +
-+	return n;
++err_timeout:
++	rt_i2c_dump_reg(i2c);
++	rt_i2c_reset(i2c);
++	return ret;
 +}
 +
 +static u32 rt_i2c_func(struct i2c_adapter *a)
@@ -311,60 +371,110 @@ Signed-off-by: John Crispin <[email protected]>
 +};
 +
 +static const struct of_device_id i2c_rt_dt_ids[] = {
-+	{ .compatible = "ralink,rt2880-i2c", .data = (void *) I2C_TYPE_RALINK },
-+	{ .compatible = "mediatek,mt7628-i2c", .data = (void *) I2C_TYPE_MEDIATEK },
++	{ .compatible = "ralink,rt2880-i2c" },
 +	{ /* sentinel */ }
 +};
 +
 +MODULE_DEVICE_TABLE(of, i2c_rt_dt_ids);
 +
++static struct i2c_adapter_quirks rt_i2c_quirks = {
++        .max_write_len = BYTECNT_MAX,
++        .max_read_len = BYTECNT_MAX,
++};
++
++static int rt_i2c_init(struct rt_i2c *i2c)
++{
++	u32 reg;
++
++	/* i2c_sclk = periph_clk / ((2 * clk_div) + 5) */
++	i2c->clk_div = (clk_get_rate(i2c->clk) - (5 * i2c->cur_clk)) /
++		(2 * i2c->cur_clk);
++	if (i2c->clk_div < 8)
++		i2c->clk_div = 8;
++	if (i2c->clk_div > I2C_CLKDIV_MASK)
++		i2c->clk_div = I2C_CLKDIV_MASK;
++
++	/* check support combinde/repeated start message */
++	rt_i2c_w32(i2c, NOSTOP_CMD, REG_STARTXFR_REG);
++	reg = rt_i2c_r32(i2c, REG_STARTXFR_REG) & NOSTOP_CMD;
++
++	rt_i2c_reset(i2c);
++
++	return reg;
++}
++
 +static int rt_i2c_probe(struct platform_device *pdev)
 +{
-+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	struct resource *res;
++	struct rt_i2c *i2c;
++	struct i2c_adapter *adap;
 +	const struct of_device_id *match;
-+	int ret;
++	int ret, restart;
 +
 +	match = of_match_device(i2c_rt_dt_ids, &pdev->dev);
-+	hw_type = (int) match->data;
 +
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 +	if (!res) {
 +		dev_err(&pdev->dev, "no memory resource found\n");
 +		return -ENODEV;
 +	}
 +
-+	adapter = devm_kzalloc(&pdev->dev, sizeof(struct i2c_adapter), GFP_KERNEL);
-+	if (!adapter) {
++	i2c = devm_kzalloc(&pdev->dev, sizeof(struct rt_i2c), GFP_KERNEL);
++	if (!i2c) {
 +		dev_err(&pdev->dev, "failed to allocate i2c_adapter\n");
 +		return -ENOMEM;
 +	}
 +
-+	membase = devm_ioremap_resource(&pdev->dev, res);
-+	if (IS_ERR(membase))
-+		return PTR_ERR(membase);
-+
-+	strlcpy(adapter->name, dev_name(&pdev->dev), sizeof(adapter->name));
-+	adapter->owner = THIS_MODULE;
-+	adapter->nr = pdev->id;
-+	adapter->timeout = HZ;
-+	adapter->algo = &rt_i2c_algo;
-+	adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
-+	adapter->dev.parent = &pdev->dev;
-+	adapter->dev.of_node = pdev->dev.of_node;
-+
-+	ret = i2c_add_numbered_adapter(adapter);
-+	if (ret)
-+		return ret;
++	i2c->base = devm_ioremap_resource(&pdev->dev, res);
++	if (IS_ERR(i2c->base))
++		return PTR_ERR(i2c->base);
 +
-+	platform_set_drvdata(pdev, adapter);
++	i2c->clk = devm_clk_get(&pdev->dev, NULL);
++	if (IS_ERR(i2c->clk)) {
++		dev_err(&pdev->dev, "no clock defined\n");
++		return -ENODEV;
++	}
++	clk_prepare_enable(i2c->clk);
++	i2c->dev = &pdev->dev;
++
++	if (of_property_read_u32(pdev->dev.of_node,
++				"clock-frequency", &i2c->cur_clk))
++		i2c->cur_clk = 100000;
++
++	adap = &i2c->adap;
++	adap->owner = THIS_MODULE;
++	adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
++	adap->algo = &rt_i2c_algo;
++	adap->retries = 3;
++	adap->dev.parent = &pdev->dev;
++	i2c_set_adapdata(adap, i2c);
++	adap->dev.of_node = pdev->dev.of_node;
++	strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name));
++	adap->quirks = &rt_i2c_quirks;
++
++	platform_set_drvdata(pdev, i2c);
++
++	restart = rt_i2c_init(i2c);
++
++	ret = i2c_add_adapter(adap);
++	if (ret < 0) {
++		dev_err(&pdev->dev, "failed to add adapter\n");
++		clk_disable_unprepare(i2c->clk);
++		return ret;
++	}
 +
-+	dev_info(&pdev->dev, "loaded\n");
++	dev_info(&pdev->dev, "clock %uKHz, re-start %ssupport\n",
++			i2c->cur_clk/1000, restart ? "" : "not ");
 +
-+	return 0;
++	return ret;
 +}
 +
 +static int rt_i2c_remove(struct platform_device *pdev)
 +{
-+	platform_set_drvdata(pdev, NULL);
++	struct rt_i2c *i2c = platform_get_drvdata(pdev);
++
++	i2c_del_adapter(&i2c->adap);
++	clk_disable_unprepare(i2c->clk);
 +
 +	return 0;
 +}
@@ -389,8 +499,7 @@ Signed-off-by: John Crispin <[email protected]>
 +{
 +	platform_driver_unregister(&rt_i2c_driver);
 +}
-+
-+module_exit (i2c_rt_exit);
++module_exit(i2c_rt_exit);
 +
 +MODULE_AUTHOR("Steven Liu <[email protected]>");
 +MODULE_DESCRIPTION("Ralink I2c host driver");

target/linux/ramips/patches-4.4/0045-i2c-add-mt7621-driver.patch

@@ -13,12 +13,13 @@ Signed-off-by: John Crispin <[email protected]>
 
 --- a/drivers/i2c/busses/Kconfig
 +++ b/drivers/i2c/busses/Kconfig
-@@ -810,6 +810,10 @@ config I2C_RALINK
- 	tristate "Ralink I2C Controller"
+@@ -811,6 +811,11 @@ config I2C_RALINK
+ 	depends on RALINK && !SOC_MT7621
  	select OF_I2C
  
 +config I2C_MT7621
-+	tristate "MT7621 I2C Controller"
++	tristate "MT7621/MT7628 I2C Controller"
++	depends on RALINK && (SOC_MT7620 || SOC_MT7621)
 +	select OF_I2C
 +
  config HAVE_S3C2410_I2C
@@ -36,11 +37,12 @@ Signed-off-by: John Crispin <[email protected]>
  obj-$(CONFIG_I2C_RK3X)		+= i2c-rk3x.o
 --- /dev/null
 +++ b/drivers/i2c/busses/i2c-mt7621.c
-@@ -0,0 +1,303 @@
+@@ -0,0 +1,433 @@
 +/*
 + * drivers/i2c/busses/i2c-mt7621.c
 + *
 + * Copyright (C) 2013 Steven Liu <[email protected]>
++ * Copyright (C) 2016 Michael Lee <[email protected]>
 + *
 + * Improve driver for i2cdetect from i2c-tools to detect i2c devices on the bus.
 + * (C) 2014 Sittisak <[email protected]>
@@ -65,276 +67,405 @@ Signed-off-by: John Crispin <[email protected]>
 +#include <linux/init.h>
 +#include <linux/errno.h>
 +#include <linux/platform_device.h>
++#include <linux/of_platform.h>
 +#include <linux/i2c.h>
 +#include <linux/io.h>
 +#include <linux/err.h>
++#include <linux/clk.h>
++
++#define REG_SM0CFG0		0x08
++#define REG_SM0DOUT		0x10
++#define REG_SM0DIN		0x14
++#define REG_SM0ST		0x18
++#define REG_SM0AUTO		0x1C
++#define REG_SM0CFG1		0x20
++#define REG_SM0CFG2		0x28
++#define REG_SM0CTL0		0x40
++#define REG_SM0CTL1		0x44
++#define REG_SM0D0		0x50
++#define REG_SM0D1		0x54
++#define REG_PINTEN		0x5C
++#define REG_PINTST		0x60
++#define REG_PINTCL		0x64
++
++/* REG_SM0CFG0 */
++#define I2C_DEVADDR_MASK	0x7f
++
++/* REG_SM0ST */
++#define I2C_DATARDY		BIT(2)
++#define I2C_SDOEMPTY		BIT(1)
++#define I2C_BUSY		BIT(0)
++
++/* REG_SM0AUTO */
++#define READ_CMD		BIT(0)
++
++/* REG_SM0CFG1 */
++#define BYTECNT_MAX		64
++#define SET_BYTECNT(x)		(x - 1)
++
++/* REG_SM0CFG2 */
++#define AUTOMODE_EN		BIT(0)
++
++/* REG_SM0CTL0 */
++#define ODRAIN_HIGH_SM0		BIT(31)
++#define VSYNC_SHIFT		28
++#define VSYNC_MASK		0x3
++#define VSYNC_PULSE		(0x1 << VSYNC_SHIFT)
++#define VSYNC_RISING		(0x2 << VSYNC_SHIFT)
++#define CLK_DIV_SHIFT		16
++#define CLK_DIV_MASK		0xfff
++#define DEG_CNT_SHIFT		8
++#define DEG_CNT_MASK		0xff
++#define WAIT_HIGH		BIT(6)
++#define DEG_EN			BIT(5)
++#define CS_STATUA		BIT(4)
++#define SCL_STATUS		BIT(3)
++#define SDA_STATUS		BIT(2)
++#define SM0_EN			BIT(1)
++#define SCL_STRECH		BIT(0)
++
++/* REG_SM0CTL1 */
++#define ACK_SHIFT		16
++#define ACK_MASK		0xff
++#define PGLEN_SHIFT		8
++#define PGLEN_MASK		0x7
++#define SM0_MODE_SHIFT		4
++#define SM0_MODE_MASK		0x7
++#define SM0_MODE_START		0x1
++#define SM0_MODE_WRITE		0x2
++#define SM0_MODE_STOP		0x3
++#define SM0_MODE_READ_NACK	0x4
++#define SM0_MODE_READ_ACK	0x5
++#define SM0_TRI_BUSY		BIT(0)
++
++/* timeout waiting for I2C devices to respond (clock streching) */
++#define TIMEOUT_MS              1000
++#define DELAY_INTERVAL_US       100
++
++struct mtk_i2c {
++	void __iomem *base;
++	struct clk *clk;
++	struct device *dev;
++	struct i2c_adapter adap;
++	u32 cur_clk;
++	u32 clk_div;
++	u32 flags;
++};
 +
-+#include <asm/mach-ralink/ralink_regs.h>
-+
-+#define REG_CONFIG_REG                       0x00
-+#define REG_CLKDIV_REG                       0x04
-+#define REG_DEVADDR_REG                      0x08
-+#define REG_ADDR_REG                         0x0C
-+#define REG_DATAOUT_REG                      0x10
-+#define REG_DATAIN_REG                       0x14
-+#define REG_STATUS_REG                       0x18
-+#define REG_STARTXFR_REG                     0x1C
-+#define REG_BYTECNT_REG                      0x20
-+#define REG_SM0_IS_AUTOMODE                  0x28
-+#define REG_SM0CTL0                          0x40
-+
-+
-+#define I2C_STARTERR                         0x10
-+#define I2C_ACKERR                           0x08
-+#define I2C_DATARDY                          0x04
-+#define I2C_SDOEMPTY                         0x02
-+#define I2C_BUSY                             0x01
-+
-+/* I2C_CFG register bit field */
-+#define I2C_CFG_ADDRLEN_8                    (7<<5)	/* 8 bits */
-+#define I2C_CFG_DEVADLEN_7                   (6<<2)
-+#define I2C_CFG_ADDRDIS                      BIT(1)
-+#define I2C_CFG_DEVADDIS                     BIT(0)
-+
-+#define I2C_CFG_DEFAULT	(I2C_CFG_ADDRLEN_8 | \
-+		I2C_CFG_DEVADLEN_7 | \
-+		I2C_CFG_ADDRDIS)
-+
-+#define I2C_RETRY                            0x1000
-+
-+#define CLKDIV_VALUE                         333
-+#define i2c_busy_loop                        (CLKDIV_VALUE*30)
-+
-+#define READ_CMD                             0x01
-+#define WRITE_CMD                            0x00
-+#define READ_BLOCK                           16
-+
-+#define SM0_ODRAIN                           BIT(31)
-+#define SM0_VSYNC_MODE                       BIT(28)
-+#define SM0_CLK_DIV                          (CLKDIV_VALUE << 16)
-+#define SM0_WAIT_LEVEL                       BIT(6)
-+#define SM0_EN                               BIT(1)
-+
-+#define SM0_CFG_DEFUALT (SM0_ODRAIN | SM0_VSYNC_MODE | \
-+                        SM0_CLK_DIV | SM0_WAIT_LEVEL | \
-+                        SM0_EN) 
-+/***********************************************************/
-+
-+static void __iomem *membase;
-+static struct i2c_adapter *adapter;
-+
-+static void rt_i2c_w32(u32 val, unsigned reg)
++static void mtk_i2c_w32(struct mtk_i2c *i2c, u32 val, unsigned reg)
 +{
-+	iowrite32(val, membase + reg);
++	iowrite32(val, i2c->base + reg);
 +}
 +
-+static u32 rt_i2c_r32(unsigned reg)
++static u32 mtk_i2c_r32(struct mtk_i2c *i2c, unsigned reg)
 +{
-+	return ioread32(membase + reg);
++	return ioread32(i2c->base + reg);
 +}
 +
-+static void mt7621_i2c_reset(struct i2c_adapter *a)
++static int poll_down_timeout(void __iomem *addr, u32 mask)
 +{
-+	device_reset(a->dev.parent);
++	unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
++
++	do {
++		if (!(readl_relaxed(addr) & mask))
++			return 0;
++
++		usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
++	} while (time_before(jiffies, timeout));
++
++	return (readl_relaxed(addr) & mask) ? -EAGAIN : 0;
 +}
-+static void mt7621_i2c_enable(struct i2c_msg *msg)
++
++static int mtk_i2c_wait_idle(struct mtk_i2c *i2c)
 +{
-+	rt_i2c_w32(msg->addr,REG_DEVADDR_REG);
-+	rt_i2c_w32(0,REG_ADDR_REG);
++	int ret;
++
++	ret = poll_down_timeout(i2c->base + REG_SM0ST, I2C_BUSY);
++	if (ret < 0)
++		dev_dbg(i2c->dev, "idle err(%d)\n", ret);
++
++	return ret;
 +}
 +
-+static void i2c_master_init(struct i2c_adapter *a)
++static int poll_up_timeout(void __iomem *addr, u32 mask)
 +{
-+	mt7621_i2c_reset(a); 
-+	rt_i2c_w32(I2C_CFG_DEFAULT,REG_CONFIG_REG);    
-+	rt_i2c_w32(SM0_CFG_DEFUALT,REG_SM0CTL0);
-+	rt_i2c_w32(1,REG_SM0_IS_AUTOMODE);//auto mode
-+}
++	unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
++	u32 status;
 +
++	do {
++		status = readl_relaxed(addr);
++		if (status & mask)
++			return 0;
++		usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
++	} while (time_before(jiffies, timeout));
 +
-+static inline int rt_i2c_wait_rx_done(void)
-+{
-+	int i=0;
-+	while((!(rt_i2c_r32(REG_STATUS_REG) & I2C_DATARDY)) && (i<i2c_busy_loop))
-+		i++;
-+	if(i>=i2c_busy_loop){
-+		pr_err("err,wait for idle timeout");
-+		return -ETIMEDOUT;
-+	}
-+	return 0;
++	return -ETIMEDOUT;
 +}
 +
-+static inline int rt_i2c_wait_idle(void)
++static int mtk_i2c_wait_rx_done(struct mtk_i2c *i2c)
 +{
-+	int i=0;
-+	while((rt_i2c_r32(REG_STATUS_REG) & I2C_BUSY) && (i<i2c_busy_loop))
-+		i++;
-+	if(i>=i2c_busy_loop){
-+		pr_err("err,wait for idle timeout");
-+		return -ETIMEDOUT;
-+	}
-+	return 0;
++	int ret;
++
++	ret = poll_up_timeout(i2c->base + REG_SM0ST, I2C_DATARDY);
++	if (ret < 0)
++		dev_dbg(i2c->dev, "rx err(%d)\n", ret);
++
++	return ret;
 +}
 +
-+static inline int rt_i2c_wait_tx_done(void)
++static int mtk_i2c_wait_tx_done(struct mtk_i2c *i2c)
 +{
-+	int i=0;
-+	while((!(rt_i2c_r32(REG_STATUS_REG) & I2C_SDOEMPTY)) && (i<i2c_busy_loop))
-+		i++;
-+	if(i>=i2c_busy_loop){
-+		pr_err("err,wait for idle timeout");
-+		return -ETIMEDOUT;
-+	}
-+	return 0;
++	int ret;
++
++	ret = poll_up_timeout(i2c->base + REG_SM0ST, I2C_SDOEMPTY);
++	if (ret < 0)
++		dev_dbg(i2c->dev, "tx err(%d)\n", ret);
++
++	return ret;
 +}
 +
-+static int rt_i2c_handle_msg(struct i2c_adapter *a, struct i2c_msg* msg)
++static void mtk_i2c_reset(struct mtk_i2c *i2c)
 +{
-+	int i = 0, j = 0, pos = 0;
-+	int nblock = msg->len / READ_BLOCK;
-+	int rem = msg->len % READ_BLOCK;
++	u32 reg;
++	device_reset(i2c->adap.dev.parent);
++	barrier();
 +
-+	if (msg->flags & I2C_M_TEN) {
-+		printk("10 bits addr not supported\n");
-+		return -EINVAL;
-+	}
++	/* ctrl0 */
++	reg = ODRAIN_HIGH_SM0 | VSYNC_PULSE | (i2c->clk_div << CLK_DIV_SHIFT) |
++		WAIT_HIGH | SM0_EN;
++	mtk_i2c_w32(i2c, reg, REG_SM0CTL0);
 +
-+	if (msg->flags & I2C_M_RD) {
-+		for (i = 0; i < nblock; i++) {
-+			if (rt_i2c_wait_idle())
-+				goto err_timeout;
-+			rt_i2c_w32(READ_BLOCK - 1, REG_BYTECNT_REG);
-+			rt_i2c_w32(READ_CMD, REG_STARTXFR_REG);
-+			for (j = 0; j < READ_BLOCK; j++) {
-+				if (rt_i2c_wait_rx_done())
-+					goto err_timeout;
-+				msg->buf[pos++] = rt_i2c_r32(REG_DATAIN_REG);
-+			}
-+		}
++	/* auto mode */
++	mtk_i2c_w32(i2c, AUTOMODE_EN, REG_SM0CFG2);
++}
++
++static void mtk_i2c_dump_reg(struct mtk_i2c *i2c)
++{
++	dev_dbg(i2c->dev, "cfg0 %08x, dout %08x, din %08x, " \
++			"status %08x, auto %08x, cfg1 %08x, " \
++			"cfg2 %08x, ctl0 %08x, ctl1 %08x\n",
++			mtk_i2c_r32(i2c, REG_SM0CFG0),
++			mtk_i2c_r32(i2c, REG_SM0DOUT),
++			mtk_i2c_r32(i2c, REG_SM0DIN),
++			mtk_i2c_r32(i2c, REG_SM0ST),
++			mtk_i2c_r32(i2c, REG_SM0AUTO),
++			mtk_i2c_r32(i2c, REG_SM0CFG1),
++			mtk_i2c_r32(i2c, REG_SM0CFG2),
++			mtk_i2c_r32(i2c, REG_SM0CTL0),
++			mtk_i2c_r32(i2c, REG_SM0CTL1));
++}
 +
-+		if (rt_i2c_wait_idle())
-+		    goto err_timeout;
-+		rt_i2c_w32(rem - 1, REG_BYTECNT_REG);
-+		rt_i2c_w32(READ_CMD, REG_STARTXFR_REG);
-+		
-+		for (i = 0; i < rem; i++) {
-+			if (rt_i2c_wait_rx_done())
-+				goto err_timeout;
-+			msg->buf[pos++] = rt_i2c_r32(REG_DATAIN_REG);
++static int mtk_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
++		int num)
++{
++	struct mtk_i2c *i2c;
++	struct i2c_msg *pmsg;
++	int i, j, ret;
++	u32 cmd;
++
++	i2c = i2c_get_adapdata(adap);
++
++	for (i = 0; i < num; i++) {
++		pmsg = &msgs[i];
++		cmd = 0;
++
++		dev_dbg(i2c->dev, "addr: 0x%x, len: %d, flags: 0x%x\n",
++				pmsg->addr, pmsg->len, pmsg->flags);
++
++		/* wait hardware idle */
++		if ((ret = mtk_i2c_wait_idle(i2c)))
++			goto err_timeout;
++
++		if (pmsg->flags & I2C_M_TEN) {
++			dev_dbg(i2c->dev, "10 bits addr not supported\n");
++			return -EINVAL;
++		} else {
++			/* 7 bits address */
++			mtk_i2c_w32(i2c, pmsg->addr & I2C_DEVADDR_MASK,
++					REG_SM0CFG0);
 +		}
-+	} else {
-+		if (rt_i2c_wait_idle())
-+	        	goto err_timeout;
-+		rt_i2c_w32(msg->len - 1, REG_BYTECNT_REG);
-+		for (i = 0; i < msg->len; i++) {
-+			rt_i2c_w32(msg->buf[i], REG_DATAOUT_REG);
-+			if(i == 0)
-+				rt_i2c_w32(WRITE_CMD, REG_STARTXFR_REG);
-+
-+			if (rt_i2c_wait_tx_done())
-+				goto err_timeout;
++
++		/* buffer length */
++		if (pmsg->len == 0) {
++			dev_dbg(i2c->dev, "length is 0\n");
++			return -EINVAL;
++		} else
++			mtk_i2c_w32(i2c, SET_BYTECNT(pmsg->len),
++					REG_SM0CFG1);
++
++		j = 0;
++		if (pmsg->flags & I2C_M_RD) {
++			cmd |= READ_CMD;
++			/* start transfer */
++			barrier();
++			mtk_i2c_w32(i2c, cmd, REG_SM0AUTO);
++			do {
++				/* wait */
++				if ((ret = mtk_i2c_wait_rx_done(i2c)))
++					goto err_timeout;
++				/* read data */
++				if (pmsg->len)
++					pmsg->buf[j] = mtk_i2c_r32(i2c,
++							REG_SM0DIN);
++				j++;
++			} while (j < pmsg->len);
++		} else {
++			do {
++				/* write data */
++				if (pmsg->len)
++					mtk_i2c_w32(i2c, pmsg->buf[j],
++							REG_SM0DOUT);
++				/* start transfer */
++				if (j == 0) {
++					barrier();
++					mtk_i2c_w32(i2c, cmd, REG_SM0AUTO);
++				}
++				/* wait */
++				if ((ret = mtk_i2c_wait_tx_done(i2c)))
++					goto err_timeout;
++				j++;
++			} while (j < pmsg->len);
 +		}
 +	}
++	/* the return value is number of executed messages */
++	ret = i;
 +
-+	return 0;
-+err_timeout:
-+	return -ETIMEDOUT;
-+}
++	return ret;
 +
-+static int rt_i2c_master_xfer(struct i2c_adapter *a, struct i2c_msg *m, int n)
-+{
-+	int i = 0;
-+	int ret = 0;
-+	i2c_master_init(a);
-+	mt7621_i2c_enable(m);
-+
-+	for (i = 0; i != n && ret==0; i++) {
-+		ret = rt_i2c_handle_msg(a, &m[i]);
-+		if (ret) 
-+			return ret;	
-+	}
-+	return i;
++err_timeout:
++	mtk_i2c_dump_reg(i2c);
++	mtk_i2c_reset(i2c);
++	return ret;
 +}
 +
-+static u32 rt_i2c_func(struct i2c_adapter *a)
++static u32 mtk_i2c_func(struct i2c_adapter *a)
 +{
 +	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
 +}
 +
-+static const struct i2c_algorithm rt_i2c_algo = {
-+	.master_xfer	= rt_i2c_master_xfer,
-+	.functionality	= rt_i2c_func,
++static const struct i2c_algorithm mtk_i2c_algo = {
++	.master_xfer	= mtk_i2c_master_xfer,
++	.functionality	= mtk_i2c_func,
 +};
 +
-+static int rt_i2c_probe(struct platform_device *pdev)
++static const struct of_device_id i2c_mtk_dt_ids[] = {
++	{ .compatible = "mediatek,mt7621-i2c" },
++	{ /* sentinel */ }
++};
++
++MODULE_DEVICE_TABLE(of, i2c_mtk_dt_ids);
++
++static struct i2c_adapter_quirks mtk_i2c_quirks = {
++        .max_write_len = BYTECNT_MAX,
++        .max_read_len = BYTECNT_MAX,
++};
++
++static void mtk_i2c_init(struct mtk_i2c *i2c)
++{
++	i2c->clk_div = clk_get_rate(i2c->clk) / i2c->cur_clk;
++	if (i2c->clk_div > CLK_DIV_MASK)
++		i2c->clk_div = CLK_DIV_MASK;
++
++	mtk_i2c_reset(i2c);
++}
++
++static int mtk_i2c_probe(struct platform_device *pdev)
 +{
-+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	struct resource *res;
++	struct mtk_i2c *i2c;
++	struct i2c_adapter *adap;
++	const struct of_device_id *match;
 +	int ret;
 +
-+	adapter = devm_kzalloc(&pdev->dev,sizeof(struct i2c_adapter), GFP_KERNEL);
-+	if (!adapter) {
++	match = of_match_device(i2c_mtk_dt_ids, &pdev->dev);
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (!res) {
++		dev_err(&pdev->dev, "no memory resource found\n");
++		return -ENODEV;
++	}
++
++	i2c = devm_kzalloc(&pdev->dev, sizeof(struct mtk_i2c), GFP_KERNEL);
++	if (!i2c) {
 +		dev_err(&pdev->dev, "failed to allocate i2c_adapter\n");
 +		return -ENOMEM;
 +	}
-+	membase = devm_ioremap_resource(&pdev->dev, res);
-+	if (IS_ERR(membase))
-+		return PTR_ERR(membase);
-+
-+	strlcpy(adapter->name, dev_name(&pdev->dev), sizeof(adapter->name));
-+
-+	adapter->owner = THIS_MODULE;
-+	adapter->nr = pdev->id;
-+	adapter->timeout = HZ;
-+	adapter->algo = &rt_i2c_algo;
-+	adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
-+	adapter->dev.parent = &pdev->dev;
-+	adapter->dev.of_node = pdev->dev.of_node;
-+
-+	platform_set_drvdata(pdev, adapter);
-+	
-+	ret = i2c_add_numbered_adapter(adapter);
-+	if (ret)
++
++	i2c->base = devm_ioremap_resource(&pdev->dev, res);
++	if (IS_ERR(i2c->base))
++		return PTR_ERR(i2c->base);
++
++	i2c->clk = devm_clk_get(&pdev->dev, NULL);
++	if (IS_ERR(i2c->clk)) {
++		dev_err(&pdev->dev, "no clock defined\n");
++		return -ENODEV;
++	}
++	clk_prepare_enable(i2c->clk);
++	i2c->dev = &pdev->dev;
++
++	if (of_property_read_u32(pdev->dev.of_node,
++				"clock-frequency", &i2c->cur_clk))
++		i2c->cur_clk = 100000;
++
++	adap = &i2c->adap;
++	adap->owner = THIS_MODULE;
++	adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
++	adap->algo = &mtk_i2c_algo;
++	adap->retries = 3;
++	adap->dev.parent = &pdev->dev;
++	i2c_set_adapdata(adap, i2c);
++	adap->dev.of_node = pdev->dev.of_node;
++	strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name));
++	adap->quirks = &mtk_i2c_quirks;
++
++	platform_set_drvdata(pdev, i2c);
++
++	mtk_i2c_init(i2c);
++
++	ret = i2c_add_adapter(adap);
++	if (ret < 0) {
++		dev_err(&pdev->dev, "failed to add adapter\n");
++		clk_disable_unprepare(i2c->clk);
 +		return ret;
++	}
 +
-+	dev_info(&pdev->dev,"loaded");
++	dev_info(&pdev->dev, "clock %uKHz, re-start not support\n",
++			i2c->cur_clk/1000);
 +
-+	return 0;
++	return ret;
 +}
 +
-+static int rt_i2c_remove(struct platform_device *pdev)
++static int mtk_i2c_remove(struct platform_device *pdev)
 +{
-+	platform_set_drvdata(pdev, NULL);
-+	return 0;
-+}
++	struct mtk_i2c *i2c = platform_get_drvdata(pdev);
 +
-+static const struct of_device_id i2c_rt_dt_ids[] = {
-+	{ .compatible = "ralink,i2c-mt7621", },
-+	{ /* sentinel */ }
-+};
++	i2c_del_adapter(&i2c->adap);
++	clk_disable_unprepare(i2c->clk);
 +
-+MODULE_DEVICE_TABLE(of, i2c_rt_dt_ids);
++	return 0;
++}
 +
-+static struct platform_driver rt_i2c_driver = {
-+	.probe		= rt_i2c_probe,
-+	.remove		= rt_i2c_remove,
++static struct platform_driver mtk_i2c_driver = {
++	.probe		= mtk_i2c_probe,
++	.remove		= mtk_i2c_remove,
 +	.driver		= {
 +		.owner	= THIS_MODULE,
 +		.name	= "i2c-mt7621",
-+		.of_match_table = i2c_rt_dt_ids,
++		.of_match_table = i2c_mtk_dt_ids,
 +	},
 +};
 +
-+static int __init i2c_rt_init (void)
++static int __init i2c_mtk_init (void)
 +{
-+	return platform_driver_register(&rt_i2c_driver);
++	return platform_driver_register(&mtk_i2c_driver);
 +}
++subsys_initcall(i2c_mtk_init);
 +
-+static void __exit i2c_rt_exit (void)
++static void __exit i2c_mtk_exit (void)
 +{
-+	platform_driver_unregister(&rt_i2c_driver);
++	platform_driver_unregister(&mtk_i2c_driver);
 +}
-+module_init (i2c_rt_init);
-+module_exit (i2c_rt_exit);
++module_exit(i2c_mtk_exit);
 +
 +MODULE_AUTHOR("Steven Liu <[email protected]>");
 +MODULE_DESCRIPTION("MT7621 I2c host driver");