mediatek: filogic: add JCG Q30 PRO support

Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: Winbond 128MB
  RAM: DDR3 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset
  Power: DC 12V 1A

Flash instructions:
  1. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  2. Attach UART, pause at u-boot menu.
  3. Select "Upgrade ATF BL2", then use preloader.bin
  4. Select "Upgrade ATF FIP", then use bl31-uboot.fip
  5. Download the initramfs image, and type "reset",
     waiting for tftp recovery to complete.
  6. After openwrt boots up, perform sysupgrade.

Note:
  1. Since NMBM is disabled, we must back up all partitions.
  2. Although we can upgrade new firmware in the stock firmware,
     we need the special fit image signature of MediaTek and
     dual boot (hack kernel) to make u-boot boot it. So just
     abandon these hacks and flash it via the serial port.

Signed-off-by: Chukun Pan <[email protected]>

target/linux/mediatek/dts/mt7981b-jcg-q30-pro.dts

@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7981.dtsi"
+
+/ {
+	model = "JCG Q30 PRO";
+	compatible = "jcg,q30-pro", "mediatek,mt7981";
+
+	aliases {
+		serial0 = &uart0;
+		label-mac-device = &gmac0;
+		led-boot = &led_status_red;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_blue;
+		led-upgrade = &led_status_blue;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x10000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: red {
+			label = "red:status";
+			gpios = <&pio 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_status_blue: blue {
+			label = "blue:status";
+			gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		nvmem-cells = <&macaddr_lan>;
+		nvmem-cell-names = "mac-address";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+};
+
+&mdio_bus {
+	switch: switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_flash_pins>;
+	status = "okay";
+
+	spi_nand@0 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+
+		spi-max-frequency = <52000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bl2";
+				reg = <0x0000000 0x0100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "u-boot-env";
+				reg = <0x0100000 0x0080000>;
+			};
+
+			factory: partition@180000 {
+				label = "Factory";
+				reg = <0x0180000 0x0200000>;
+				read-only;
+			};
+
+			partition@380000 {
+				label = "fip";
+				reg = <0x0380000 0x0200000>;
+				read-only;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x0580000 0x7000000>;
+			};
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+			nvmem-cells = <&macaddr_wan>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan1";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan3";
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	spi0_flash_pins: spi0-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+
+		conf-pd {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+
+	mediatek,mtd-eeprom = <&factory 0x0>;
+};
+
+&factory {
+	compatible = "nvmem-cells";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	macaddr_wan: macaddr@a0024 {
+		reg = <0xa0024 0x6>;
+	};
+
+	macaddr_lan: macaddr@a002a {
+		reg = <0xa002a 0x6>;
+	};
+};

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -49,6 +49,7 @@ mediatek_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1
 		;;
 	cetron,ct3003|\
+	jcg,q30-pro|\
 	qihoo,360t7)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan
 		;;

target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac

@@ -65,6 +65,11 @@ case "$board" in
 		[ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
 		[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
 		;;
+	jcg,q30-pro)
+		# Originally, phy1 is phy0 mac with LA bit set. However, this would conflict
+		# addresses on multiple VIFs with the other radio. Use label mac to set LA bit.
+		[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(get_mac_label) > /sys${DEVPATH}/macaddress
+		;;
 	mercusys,mr90x-v1)
 		addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
 		[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress

target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh

@@ -112,6 +112,7 @@ platform_do_upgrade() {
 		emmc_do_upgrade "$1"
 		;;
 	h3c,magic-nx30-pro|\
+	jcg,q30-pro|\
 	mediatek,mt7981-rfb|\
 	qihoo,360t7|\
 	tplink,tl-xdr4288|\

target/linux/mediatek/image/filogic.mk

@@ -330,6 +330,30 @@ define Device/h3c_magic-nx30-pro
 endef
 TARGET_DEVICES += h3c_magic-nx30-pro
 
+define Device/jcg_q30-pro
+  DEVICE_VENDOR := JCG
+  DEVICE_MODEL := Q30 PRO
+  DEVICE_DTS := mt7981b-jcg-q30-pro
+  DEVICE_DTS_DIR := ../dts
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  KERNEL_IN_UBI := 1
+  UBOOTENV_IN_UBI := 1
+  IMAGES := sysupgrade.itb
+  KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+  KERNEL := kernel-bin | gzip
+  KERNEL_INITRAMFS := kernel-bin | lzma | \
+        fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+  IMAGE/sysupgrade.itb := append-kernel | \
+        fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
+  DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+  ARTIFACTS := preloader.bin bl31-uboot.fip
+  ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
+  ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot jcg_q30-pro
+endef
+TARGET_DEVICES += jcg_q30-pro
+
 define Device/netgear_wax220
   DEVICE_VENDOR := NETGEAR
   DEVICE_MODEL := WAX220