mvebu: add support for iEi Puzzle-M901/Puzzle-M902

 Hardware specification
 ----------------------
 * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
 * 4 GB DDR
 * 4 GB eMMC
 * mmcblk0
 - mmcblk0p1    64M  kernel_1
 - mmcblk0p2    64M  kernel_2
 - mmcblk0p3   512M  rootfs_1
 - mmcblk0p4   512M  rootfs_2
 - mmcblk0p5   512M  Reserved
 - mmcblk0p6    64M  Reserved
 - mmcblk0p7   1.8G  rootfs_data

 * 4 MB (SPI Flash)
 * 6 x 2.5 Gigabit  ports (Puzzle-M901)
 - External PHY with 6 ports (AQR112R)

 * 6 x 2.5 Gigabit ports (Puzzle-M902)
 - External PHY with 6 ports (AQR112R)
   3 x 10 Gigabit ports (Puzzle-M902)
 - External PHY with 3 ports (AQR113R)

 * 4 x Front panel LED
 * 1 x USB 3.0
 * Reset button on Rear panel
 * UART (115200 8N1,header on PCB)

 Flash instructions:
    The original firmware is based on OpenWrt.
    Flash firmware using LuCI and CLI

Signed-off-by: Ian Chang <[email protected]>

target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network

@@ -10,6 +10,12 @@ board_config_update
 board=$(board_name)
 
 case "$board" in
+iei,puzzle-m901)
+	ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0"
+	;;
+iei,puzzle-m902)
+	ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5 eth10 eth11 eth12" "eth0"
+	;;
 marvell,armada8040-mcbin-doubleshot|\
 marvell,armada8040-mcbin-singleshot)
 	ucidef_set_interfaces_lan_wan "eth0 eth1 eth3" "eth2"

target/linux/mvebu/cortexa72/base-files/lib/upgrade/emmc-puzzle.sh

@@ -0,0 +1,36 @@
+platform_do_upgrade_emmc() {
+	local board=$(board_name)
+	local diskdev partdev
+
+	export_bootdevice && export_partdevice diskdev 0 || {
+		v "Unable to determine upgrade device"
+		return 1
+	}
+	sync
+	if [ "$UPGRADE_OPT_SAVE_PARTITIONS" = "1" ]; then
+		get_partitions "/dev/$diskdev" bootdisk
+		v "Extract boot sector from the image"
+		get_image_dd "$1" of=/tmp/image.bs count=1 bs=512b
+		get_partitions /tmp/image.bs image
+	fi
+
+	#iterate over each partition from the image and write it to the boot disk
+	while read part start size; do
+		if export_partdevice partdev $part; then
+			if [ "$partdev" = "mmcblk0p2" ]; then
+				v "Writing image mmcblk0p3 for /dev/$partdev  $start $size"
+				get_image_dd "$1" of="/dev/mmcblk0p3" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
+			elif [ "$partdev" = "mmcblk0p1" ]; then
+				v "Writing image mmcblk0p1 for /dev/$partdev $start $size"
+				get_image_dd "$1" of="/dev/$partdev" ibs="512" obs=1M skip="$start" count="$size" conv=fsync
+			fi
+		else
+			v "Unable to find partition $part device, skipped."
+		fi
+	done < /tmp/partmap.image
+
+	v "Writing new UUID to /dev/$diskdev..."
+	get_image_dd "$1" of="/dev/$diskdev" bs=1 skip=440 count=4 seek=440 conv=fsync
+
+	sleep 1
+}

target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh

@@ -9,6 +9,8 @@ REQUIRE_IMAGE_METADATA=1
 
 platform_check_image() {
 	case "$(board_name)" in
+	iei,puzzle-m901|\
+	iei,puzzle-m902|\
 	marvell,armada8040-mcbin-doubleshot|\
 	marvell,armada8040-mcbin-singleshot)
 		legacy_sdcard_check_image "$1"
@@ -21,6 +23,10 @@ platform_check_image() {
 
 platform_do_upgrade() {
 	case "$(board_name)" in
+	iei,puzzle-m901|\
+	iei,puzzle-m902)
+		platform_do_upgrade_emmc "$1"
+		;;
 	marvell,armada8040-mcbin-doubleshot|\
 	marvell,armada8040-mcbin-singleshot)
 		legacy_sdcard_do_upgrade "$1"
@@ -32,6 +38,8 @@ platform_do_upgrade() {
 }
 platform_copy_config() {
 	case "$(board_name)" in
+	iei,puzzle-m901|\
+	iei,puzzle-m902|\
 	marvell,armada8040-mcbin-doubleshot|\
 	marvell,armada8040-mcbin-singleshot)
 		legacy_sdcard_copy_config

target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9131-puzzle-m901.dts

@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9131-DB board.
+ */
+
+#include "cn9130.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "iEi Puzzle-M901";
+	compatible = "iei,puzzle-m901",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		i2c0 = &cp1_i2c0;
+		i2c1 = &cp0_i2c0;
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+		ethernet3 = &cp1_eth0;
+		ethernet4 = &cp1_eth1;
+		ethernet5 = &cp1_eth2;
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		gpio3 = &cp1_gpio1;
+		gpio4 = &cp1_gpio2;
+	};
+
+	memory@00000000 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&cp0_uart0 {
+	status = "okay";
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+	pinctrl-names = "default";
+	bus-width = <8>;
+	status = "okay";
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+};
+
+&cp0_crypto {
+	status = "okay";
+};
+
+&cp0_xmdio {
+	status = "okay";
+	cp0_nbaset_phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <2>;
+	};
+	cp0_nbaset_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+	};
+	cp0_nbaset_phy2: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <8>;
+	};
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp0_comphy2 0>;
+	managed = "in-band-status";
+};
+
+&cp0_eth1 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp0_comphy4 1>;
+	managed = "in-band-status";
+};
+
+&cp0_eth2 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp0_comphy5 2>;
+	managed = "in-band-status";
+};
+
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
+
+&cp0_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c0_pins>;
+	status = "okay";
+	clock-frequency = <100000>;
+	rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+		wakeup-source;
+	};
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_pcie0 {
+	status = "okay";
+	num-lanes = <2>;
+	num-viewport = <8>;
+	phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>;
+};
+
+/* U55 */
+&cp0_spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi0_pins>;
+	reg = <0x700680 0x50>,          /* control */
+	      <0x2000000 0x1000000>;    /* CS0 */
+	status = "okay";
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <40000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x1f0000>;
+			};
+			partition@1f0000 {
+				label = "U-Boot ENV Factory";
+				reg = <0x1f0000 0x10000>;
+			};
+			partition@200000 {
+				label = "Reserved";
+				reg = <0x200000 0x1f0000>;
+			};
+			partition@3f0000 {
+				label = "U-Boot ENV";
+				reg = <0x3f0000 0x10000>;
+			};
+		};
+	};
+};
+
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+		cp0_i2c0_pins: cp0-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp0_i2c1_pins: cp0-i2c-pins-1 {
+			marvell,pins = "mpp35", "mpp36";
+			marvell,function = "i2c1";
+		};
+		cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
+			marvell,pins = "mpp0", "mpp1", "mpp2",
+				       "mpp3", "mpp4", "mpp5",
+				       "mpp6", "mpp7", "mpp8",
+				       "mpp9", "mpp10", "mpp11";
+			marvell,function = "ge0";
+		};
+		cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
+			marvell,pins = "mpp44", "mpp45", "mpp46",
+				       "mpp47", "mpp48", "mpp49",
+				       "mpp50", "mpp51", "mpp52",
+				       "mpp53", "mpp54", "mpp55";
+			marvell,function = "ge1";
+		};
+		cp0_spi0_pins: cp0-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+	};
+};
+
+/*
+ * Instantiate the first connected CP115
+ */
+
+#define CP11X_NAME		cp1
+#define CP11X_BASE		f6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE	f6600000
+#define CP11X_PCIE1_BASE	f6620000
+#define CP11X_PCIE2_BASE	f6640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp1_crypto {
+	status = "okay";
+};
+
+&cp1_xmdio {
+	status = "okay";
+	cp1_nbaset_phy0: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <2>;
+	};
+	cp1_nbaset_phy1: ethernet-phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+	};
+	cp1_nbaset_phy2: ethernet-phy@5 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <8>;
+	};
+};
+
+&cp1_ethernet {
+	status = "okay";
+};
+
+/* CON50 */
+&cp1_eth0 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp1_comphy2 0>;
+	managed = "in-band-status";
+};
+
+&cp1_eth1 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp1_comphy4 1>;
+	managed = "in-band-status";
+};
+
+&cp1_eth2 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp1_comphy5 2>;
+	managed = "in-band-status";
+};
+
+&cp1_sata0 {
+	status = "okay";
+	sata-port@1 {
+		status = "okay";
+		phys = <&cp1_comphy0 1>;
+	};
+};
+
+&cp1_gpio1 {
+	status = "okay";
+};
+
+&cp1_gpio2 {
+	status = "okay";
+};
+
+&cp1_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&cp1_syscon0 {
+	cp1_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+		cp1_i2c0_pins: cp1-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp1_spi0_pins: cp1-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+		cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
+			marvell,pins = "mpp3";
+			marvell,function = "gpio";
+		};
+		cp1_sfp_pins: sfp-pins {
+			marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
+			marvell,function = "gpio";
+		};
+	};
+};
+
+&cp1_usb3_1 {
+	status = "okay";
+	phys = <&cp1_comphy3 1>;
+	phy-names = "usb";
+};

target/linux/mvebu/files/arch/arm64/boot/dts/marvell/cn9132-puzzle-m902.dts

@@ -0,0 +1,481 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2019 Marvell International Ltd.
+ *
+ * Device tree for the CN9132-DB board.
+ */
+
+#include "cn9130.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "iEi Puzzle-M902";
+	compatible = "iei,puzzle-m902",
+		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		i2c0 = &cp1_i2c0;
+		i2c1 = &cp0_i2c0;
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		gpio3 = &cp1_gpio1;
+		gpio4 = &cp1_gpio2;
+		gpio5 = &cp2_gpio1;
+		gpio6 = &cp2_gpio2;
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+		ethernet3 = &cp1_eth0;
+		ethernet4 = &cp1_eth1;
+		ethernet5 = &cp1_eth2;
+		ethernet6 = &cp2_eth0;
+		ethernet7 = &cp2_eth1;
+		ethernet8 = &cp2_eth2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+		serial1 = &cp0_uart0;
+	};
+
+	memory@00000000 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	cp2_reg_usb3_vbus0: cp2_usb3_vbus@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp2-xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&cp2_gpio1 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp2_usb3_0_phy0: cp2_usb3_phy0 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp2_reg_usb3_vbus0>;
+	};
+
+	cp2_reg_usb3_vbus1: cp2_usb3_vbus@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "cp2-xhci1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&cp2_gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	cp2_usb3_0_phy1: cp2_usb3_phy1 {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&cp2_reg_usb3_vbus1>;
+	};
+
+	cp2_sfp_eth0: sfp-eth0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp2_sfpp0_i2c>;
+		los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&cp0_uart0 {
+	status = "okay";
+};
+
+/* on-board eMMC - U9 */
+&ap_sdhci0 {
+	pinctrl-names = "default";
+	bus-width = <8>;
+	status = "okay";
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+};
+
+&cp0_crypto {
+	status = "okay";
+};
+
+&cp0_xmdio {
+	status = "okay";
+	cp0_nbaset_phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <2>;
+	};
+	cp0_nbaset_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+	};
+	cp0_nbaset_phy2: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <8>;
+	};
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* SLM-1521-V2, CON9 */
+&cp0_eth0 {
+	status = "okay";
+	phy-mode = "10gbase-kr";
+	phys = <&cp0_comphy2 0>;
+	managed = "in-band-status";
+};
+
+&cp0_eth1 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp0_comphy4 1>;
+	managed = "in-band-status";
+};
+
+&cp0_eth2 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp0_comphy1 2>;
+	managed = "in-band-status";
+};
+
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
+
+&cp0_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c0_pins>;
+	status = "okay";
+	clock-frequency = <100000>;
+	rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+		wakeup-source;
+	};
+};
+
+&cp0_i2c1 {
+	clock-frequency = <100000>;
+};
+
+/* SLM-1521-V2, CON6 */
+&cp0_sata0 {
+	status = "okay";
+	sata-port@1 {
+		status = "okay";
+		phys = <&cp0_comphy0 1>;
+	};
+};
+
+&cp0_pcie2 {
+	status = "okay";
+	num-lanes = <1>;
+	num-viewport = <8>;
+	phys = <&cp0_comphy5 2>;
+};
+
+/* U55 */
+&cp0_spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi0_pins>;
+	reg = <0x700680 0x50>,          /* control */
+	      <0x2000000 0x1000000>;    /* CS0 */
+	status = "okay";
+	spi-flash@0 {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <40000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x1f0000>;
+			};
+			partition@1f0000 {
+				label = "U-Boot ENV Factory";
+				reg = <0x1f0000 0x10000>;
+			};
+			partition@200000 {
+				label = "Reserved";
+				reg = <0x200000 0x1f0000>;
+			};
+			partition@3f0000 {
+				label = "U-Boot ENV";
+				reg = <0x3f0000 0x10000>;
+			};
+		};
+	};
+};
+
+&cp0_syscon0 {
+	cp0_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+		cp0_i2c0_pins: cp0-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp0_i2c1_pins: cp0-i2c-pins-1 {
+			marvell,pins = "mpp35", "mpp36";
+			marvell,function = "i2c1";
+		};
+		cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
+			marvell,pins = "mpp0", "mpp1", "mpp2",
+				       "mpp3", "mpp4", "mpp5",
+				       "mpp6", "mpp7", "mpp8",
+				       "mpp9", "mpp10", "mpp11";
+			marvell,function = "ge0";
+		};
+		cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
+			marvell,pins = "mpp44", "mpp45", "mpp46",
+				       "mpp47", "mpp48", "mpp49",
+				       "mpp50", "mpp51", "mpp52",
+				       "mpp53", "mpp54", "mpp55";
+			marvell,function = "ge1";
+		};
+		cp0_spi0_pins: cp0-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+	};
+};
+
+&cp0_usb3_1 {
+	status = "okay";
+	phys = <&cp0_comphy3 1>;
+	phy-names = "usb";
+};
+
+/*
+ * Instantiate the first connected CP115
+ */
+
+#define CP11X_NAME		cp1
+#define CP11X_BASE		f4000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE	f4600000
+#define CP11X_PCIE1_BASE	f4620000
+#define CP11X_PCIE2_BASE	f4640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp1_crypto {
+	status = "okay";
+};
+
+&cp1_xmdio {
+	status = "okay";
+	cp1_nbaset_phy0: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <2>;
+	};
+	cp1_nbaset_phy1: ethernet-phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+	};
+	cp1_nbaset_phy2: ethernet-phy@5 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <8>;
+	};
+};
+
+&cp1_ethernet {
+	status = "okay";
+};
+
+/* CON50 */
+&cp1_eth0 {
+	status = "okay";
+	phy-mode = "10gbase-kr";
+	phys = <&cp1_comphy2 0>;
+	managed = "in-band-status";
+};
+
+&cp1_eth1 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp1_comphy4 1>;
+	managed = "in-band-status";
+};
+
+&cp1_eth2 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp1_comphy1 2>;
+	managed = "in-band-status";
+};
+
+&cp1_gpio1 {
+	status = "okay";
+};
+
+&cp1_gpio2 {
+	status = "okay";
+};
+
+&cp1_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp1_i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+&cp1_syscon0 {
+	cp1_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+		cp1_i2c0_pins: cp1-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+		cp1_spi0_pins: cp1-spi-pins-0 {
+			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+			marvell,function = "spi1";
+		};
+		cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
+			marvell,pins = "mpp3";
+			marvell,function = "gpio";
+		};
+	};
+};
+
+/*
+ * Instantiate the second connected CP115
+ */
+
+#define CP11X_NAME		cp2
+#define CP11X_BASE		f6000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe5000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE	f6600000
+#define CP11X_PCIE1_BASE	f6620000
+#define CP11X_PCIE2_BASE	f6640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+&cp2_crypto {
+	status = "okay";
+};
+
+&cp2_ethernet {
+	status = "okay";
+};
+
+&cp2_xmdio {
+	status = "okay";
+	cp2_nbaset_phy0: ethernet-phy@6 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <2>;
+	};
+	cp2_nbaset_phy1: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+	};
+	cp2_nbaset_phy2: ethernet-phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <8>;
+	};
+};
+
+/* SLM-1521-V2, CON9 */
+&cp2_eth0 {
+	status = "okay";
+	phy-mode = "10gbase-kr";
+	phys = <&cp2_comphy2 0>;
+	managed = "in-band-status";
+};
+
+&cp2_eth1 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp2_comphy4 1>;
+	managed = "in-band-status";
+};
+
+&cp2_eth2 {
+	status = "okay";
+	phy-mode = "2500base-x";
+	phys = <&cp2_comphy1 2>;
+	managed = "in-band-status";
+};
+
+&cp2_gpio1 {
+	status = "okay";
+};
+
+&cp2_gpio2 {
+	status = "okay";
+};
+
+&cp2_i2c0 {
+	clock-frequency = <100000>;
+	/* SLM-1521-V2 - U3 */
+	i2c-mux@72 {
+		compatible = "nxp,pca9544";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		cp2_sfpp0_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			/* U12 */
+			cp2_module_expander1: pca9555@21 {
+				compatible = "nxp,pca9555";
+				pinctrl-names = "default";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x21>;
+			};
+		};
+	};
+};
+
+&cp2_syscon0 {
+	cp2_pinctrl: pinctrl {
+		compatible = "marvell,cp115-standalone-pinctrl";
+		cp2_i2c0_pins: cp2-i2c-pins-0 {
+			marvell,pins = "mpp37", "mpp38";
+			marvell,function = "i2c0";
+		};
+	};
+};

target/linux/mvebu/image/cortexa72.mk

@@ -43,3 +43,21 @@ define Device/marvell_macchiatobin-singleshot
   SUPPORTED_DEVICES := marvell,armada8040-mcbin-singleshot
 endef
 TARGET_DEVICES += marvell_macchiatobin-singleshot
+
+define Device/iei_puzzle-m901
+  $(call Device/Default-arm64)
+  DEVICE_VENDOR := iEi
+  DEVICE_MODEL := Puzzle-M901
+  SOC := cn9131
+  IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
+endef
+TARGET_DEVICES += iei_puzzle-m901
+
+define Device/iei_puzzle-m902
+  $(call Device/Default-arm64)
+  DEVICE_VENDOR := iEi
+  DEVICE_MODEL := Puzzle-M902
+  SOC := cn9132
+  IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
+endef
+TARGET_DEVICES += iei_puzzle-m902