qualcommax: switch to qca8081 upstream PHY driver

Switch to qca8081 upstream PHY. Update every device that have LEDs
attached to the qca8081 PHY to follow new way of defining the LEDs and
add original OEM configuration.

Signed-off-by: Christian Marangi <[email protected]>

target/linux/qualcommax/config-6.1

@@ -55,6 +55,7 @@ CONFIG_ARM_PSCI_CPUIDLE=y
 CONFIG_ARM_PSCI_FW=y
 # CONFIG_ARM_QCOM_CPUFREQ_HW is not set
 CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y
+CONFIG_AT803X_PHY=y
 CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_SD=y

target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-ax880.dts

@@ -8,6 +8,7 @@
 #include "ipq8074-ess.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "Yuncore AX880";
@@ -313,12 +314,36 @@
 		compatible = "ethernet-phy-id004d.d101";
 		reg = <24>;
 		reset-gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 
 	qca8081_28: ethernet-phy@28 {
 		compatible = "ethernet-phy-id004d.d101";
 		reg = <28>;
 		reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
 	};
 };
 

target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-ax9000.dts

@@ -378,6 +378,18 @@
 		compatible = "ethernet-phy-id004d.d101";
 		reg = <24>;
 		reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 };
 

target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-dl-wrx36.dts

@@ -163,6 +163,25 @@
 		compatible = "ethernet-phy-id004d.d101";
 		reg = <28>;
 		reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_YELLOW>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 };
 

target/linux/qualcommax/ipq807x/base-files/etc/board.d/01_leds

@@ -10,6 +10,10 @@ arcadyan,aw1000)
 	ucidef_set_led_netdev "5g" "5G" "green:5g" "wwan0"
 	ucidef_set_led_netdev "wan" "WAN" "green:internet" "wan"
 	;;
+dynalink,dl-wrx36)
+	ucidef_set_led_netdev "wan-port-link-green" "WAN-PORT-LINK-GREEN" "90000.mdio-1:1c:green:wan" "wan" "link_2500"
+	ucidef_set_led_netdev "wan-port-link-yellow" "WAN-PORT-LINK-YELLOW" "90000.mdio-1:1c:yellow:wan" "wan" "tx rx link_10 link_100 link_1000"
+	;;
 edgecore,eap102)
 	ucidef_set_led_netdev "wan" "WAN" "green:wanpoe" "wan"
 	;;
@@ -32,6 +36,9 @@ redmi,ax6|\
 xiaomi,ax3600)
 	ucidef_set_led_netdev "wan" "WAN" "blue:network" "wan"
 	;;
+xiaomi,ax9000)
+	ucidef_set_led_netdev "wan-port-link" "WAN-PORT-LINK" "90000.mdio-1:18:green:wan" "wan" "tx rx link_10 link_100 link_1000 link_2500"
+	;;
 qnap,301w)
 	ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "lan1"
 	ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "lan2"
@@ -40,6 +47,10 @@ qnap,301w)
 	ucidef_set_led_netdev "10G_1" "10G_1" "green:10g_1" "10g-1"
 	ucidef_set_led_netdev "10G_2" "10G_2" "green:10g_2" "10g-2"
 	;;
+yuncore,ax880)
+	ucidef_set_led_netdev "wan-port-link" "WAN-PORT-LINK" "90000.mdio-1:18:green:wan" "wan" "tx rx link_10 link_100 link_1000 link_2500"
+	ucidef_set_led_netdev "lan-port-link" "LAN-PORT-LINK" "90000.mdio-1:1c:green:lan" "lan" "tx rx link_10 link_100 link_1000 link_2500"
+	;;
 esac
 
 board_config_flush