ath79: add support for TP-Link RE450 v2

TP-Link RE450 v2 is a dual band router/range-extender
based on Qualcomm/Atheros QCA9563 + QCA9880.

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button
- UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers)

Flash instruction:
Apply factory image in OEM firmware web-gui.

U-Boot does not seem to have any recovery functions, so
debricking requires connection via UART.

Signed-off-by: Peter Lundkvist <[email protected]>

target/linux/ath79/base-files/etc/board.d/01_leds

@@ -28,6 +28,10 @@ case "$board" in
 	ucidef_set_led_switch "lan1" "LAN1" "netgear:green:lan1" "switch0" "0x02" "0x0f"
 	ucidef_set_led_switch "lan2" "LAN2" "netgear:green:lan2" "switch0" "0x04" "0x0f"
 	;;
+"tplink,re450-v2")
+	ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
+	ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
+	;;
 "tplink,tl-mr3020-v1")
 	ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x02"
 	;;

target/linux/ath79/base-files/etc/board.d/02_network

@@ -13,6 +13,7 @@ ath79_setup_interfaces()
 		ucidef_set_interface_lan "eth0" "dhcp"
 		;;
 	"avm,fritz300e"|\
+	"tplink,re450-v2"|\
 	"tplink,tl-mr10u"|\
 	"tplink,tl-wr703n"|\
 	"ubnt,unifiac-lite"|\

target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -91,6 +91,10 @@ case "$FIRMWARE" in
 		ath10kcal_extract "ART" 20480 2116
 		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
 		;;
+	"tplink,re450-v2")
+		ath10kcal_extract "art" 20480 2116
+		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
+		;;
 	"tplink,tl-archer-c7-v2")
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)

target/linux/ath79/dts/qca9563_tl-re450-v2.dts

@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	compatible = "tplink,re450-v2", "qca,qca9563";
+	model = "TP-Link RE450 v2";
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-status = &system;
+		mdio-gpio0 = &mdio2;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		system: power {
+			label = "tp-link:blue:power";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan2g {
+			label = "tp-link:blue:wlan2g";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wlan5g {
+			label = "tp-link:blue:wlan5g";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy0tpt";
+		};
+
+		lan_link {
+			label = "tp-link:green:lan_link";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		lan_data {
+			label = "tp-link:green:lan_data";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		wps_blue {
+			label = "tp-link:blue:wps";
+			gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		wps_red {
+			label = "tp-link:red:wps";
+			gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		power {
+			label = "Power button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		leds {
+			label = "LED control button";
+			linux,code = <BTN_0>;
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "WPS button";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	mdio2: mdio {
+		compatible = "virtual,mdio-gpio";
+
+		gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */
+			<&gpio 4 GPIO_ACTIVE_HIGH>; /* MDIO */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@4 {
+			reg = <4>;
+			device_type = "ethernet-phy";
+			reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			partition@20000 {
+				label = "firmware";
+				reg = <0x020000 0x5e0000>;
+			};
+
+			partition@600000 {
+				label = "partition-table";
+				reg = <0x600000 0x010000>;
+				read-only;
+			};
+
+			info: partition@610000 {
+				label = "product-info";
+				reg = <0x610000 0x020000>;
+				read-only;
+			};
+
+			partition@630000 {
+				label = "config";
+				reg = <0x630000 0x020000>;
+				read-only;
+			};
+
+			art: partition@7f0000 {
+				label = "art";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+	mtd-mac-address = <&info 0x8>;
+	phy-handle = <&phy0>;
+};
+
+&wmac {
+	status = "okay";
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&info 0x8>;
+};

target/linux/ath79/image/common-tp-link.mk

@@ -1,4 +1,4 @@
-DEVICE_VARS += TPLINK_HWID TPLINK_HWREV TPLINK_FLASHLAYOUT TPLINK_HEADER_VERSION TPLINK_BOARD_NAME
+DEVICE_VARS += TPLINK_HWID TPLINK_HWREV TPLINK_FLASHLAYOUT TPLINK_HEADER_VERSION TPLINK_BOARD_NAME TPLINK_BOARD_ID
 
 define rootfs_align
 $(patsubst %-256k,0x40000,$(patsubst %-128k,0x20000,$(patsubst %-64k,0x10000,$(patsubst squashfs%,0x4,$(patsubst root.%,%,$(1))))))

target/linux/ath79/image/generic-tp-link.mk

@@ -13,6 +13,24 @@ define Device/tl-archer-c7-v2
 endef
 TARGET_DEVICES += tl-archer-c7-v2
 
+define Device/tl-re450-v2
+  $(Device/tplink)
+  ATH_SOC := qca9563
+  IMAGE_SIZE := 6016k
+  DEVICE_TITLE := TP-LINK RE450 v2
+  DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
+  TPLINK_HWID := 0x0
+  TPLINK_HWREV := 0
+  TPLINK_BOARD_ID := RE450-V2
+  LOADER_TYPE := elf
+  KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header -O
+  IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
+    append-metadata | check-size $$$$(IMAGE_SIZE)
+  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
+  SUPPORTED_DEVICES := tplink,re450-v2
+endef
+TARGET_DEVICES += tl-re450-v2
+
 define Device/tl-wdr3600
   $(Device/tplink-8mlzma)
   ATH_SOC := ar9344

tools/firmware-utils/src/tplink-safeloader.c

@@ -1079,6 +1079,46 @@ static struct device_info boards[] = {
 		.last_sysupgrade_partition = "file-system"
 	},
 
+	/** Firmware layout for the RE450 v2 */
+	{
+		.id = "RE450-V2",
+		.vendor = "",
+		.support_list =
+			"SupportList:\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:00000000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:55530000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:45550000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:4A500000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:43410000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:41550000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:41530000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:4B520000}\r\n"
+			"{product_name:RE450,product_ver:2.0.0,special_id:42520000}\r\n",
+		.support_trail = '\x00',
+		.soft_ver = NULL,
+
+		/* We're using a dynamic kernel/rootfs split here */
+		.partitions = {
+			{"fs-uboot", 0x00000, 0x20000},
+			{"firmware", 0x20000, 0x5e0000},
+			{"partition-table", 0x600000, 0x02000},
+			{"default-mac", 0x610000, 0x00020},
+			{"pin", 0x610100, 0x00020},
+			{"product-info", 0x611100, 0x01000},
+			{"soft-version", 0x620000, 0x01000},
+			{"support-list", 0x621000, 0x01000},
+			{"profile", 0x622000, 0x08000},
+			{"user-config", 0x630000, 0x10000},
+			{"default-config", 0x640000, 0x10000},
+			{"radio", 0x7f0000, 0x10000},
+
+			{NULL, 0, 0}
+		},
+
+		.first_sysupgrade_partition = "os-image",
+		.last_sysupgrade_partition = "file-system"
+	},
+
 	{}
 };