qualcommax: ipq807x: add Zyxel NWA110AX support

The Zyxel NWA110AX is a dual band 2x2:2 802.11ax wireless access point
with PoE.

The device is very similar to the NWA210AX except for being 2x2 instead
of 4x4 in the 5GHz band and not having the 2.5GbE ethernet port. This
commit factors out a common DTS and device definition and reuses it for
both devices.

Hardware:
* SoC: Qualcomm IPQ8070A
* RAM: 1GiB 1x Samsung K4A8G165WC-BCTD
* Flash: 8MiB Winbond W25Q64DW SPI-NOR, 256MiB Winbond W29N02GZ SPI-NAND
* WLAN 2.4GHz: QCN5024 2x2:2 802.11b/g/n/ax
* WLAN 5GHz: QCN5054 2x2:2 802.11n/ac/ax
* Ethernet: 1x 1GbE with AR8033 PHY
* Serial Config: 3.3V TTL 115200-8-N-1, externally accessible
* Serial Layout: GND TX RX 3.3V (don't connect, marked with triangle)
* LEDs: 1x red, 1x green, 1x blue, 1x white
* Buttons: 1x reset

MAC addresses:
* Uplink: base address on label
* 2.4GHz WLAN: base + 1
* 5GHZ WLAN: base + 2

Flashing Notes:
The device uses a dual-image setup and OpenWrt can only be installed as
image 0. When the currently running stock firmware is image 0, OpenWrt
will be installed as image 1, fail to boot and the device returns to stock
firmware. If this happens, install any version of stock firmware so that
it runs as image 1, before installing OpenWrt. Alternatively, if there
already is a valid stock firmware in image 1, the "debug dual-image show"
and "debug dual-image set boot-image image1" commands can be used in the
stock CLI via serial/SSH/telnet to switch to image 1.

Flashing with Stock Web Interface:
* Get the OpenWrt factory image and rename it to a shorter name, for
  example "openwrt.bin" (the stock firmware has a character limit)
* In the web interface, go to "Maintenance" -> "File Manager" ->
  "Firmware Package" (or click the link next to "Firmware Version" under
  "Device Information" on the dashboard)
* Under "Upload File" browse to the renamed OpenWrt factory image and
  click on "Upload"

Switch Boot Image:
* OpenWrt to stock: "zyxel-bootconfig-ipq807x set image1"
* Stock to OpenWrt: "debug dual-image set boot-image image0"

Unbrick / Revert to Stock with the Boot Module:
* Disconnect the device from power
* Configure your machine to 192.168.1.103/24 and start a TFTP server
* Put the stock firmware image into the TFTP server root and rename it to
  "ZLD-current"
* Establish a serial connection to the device through the console port
* Connect the device to power
* When prompted, press a key to abort automatic boot and enter debug mode
* Use the "atnz" command to flash the firmware image
* Use the "atgo" command to boot from the newly flashed image

Signed-off-by: Michael Lotz <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/21849
Signed-off-by: Robert Marko <[email protected]>

package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq807x

@@ -31,6 +31,7 @@ aliyun,ap8220|\
 compex,wpq873|\
 edgecore,eap102|\
 zyxel,nbg7815|\
+zyxel,nwa110ax|\
 zyxel,nwa210ax)
 	ubootenv_add_mtd "0:appsblenv" "0x0" "0x10000" "0x10000"
 	;;

package/firmware/ipq-wifi/Makefile

@@ -113,6 +113,7 @@ ALLWIFIBOARDS:= \
 	zte_mf287 \
 	zte_mf287plus \
 	zyxel_nbg7815 \
+	zyxel_nwa110ax \
 	zyxel_nwa210ax \
 	zyxel_scr50axe
 
@@ -306,6 +307,7 @@ $(eval $(call generate-ipq-wifi-package,zte_mf286c,ZTE MF286C))
 $(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287))
 $(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
 $(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
+$(eval $(call generate-ipq-wifi-package,zyxel_nwa110ax,Zyxel NWA110AX))
 $(eval $(call generate-ipq-wifi-package,zyxel_nwa210ax,Zyxel NWA210AX))
 $(eval $(call generate-ipq-wifi-package,zyxel_scr50axe,Zyxel SCR50AXE))
 

package/utils/zyxel-bootconfig-ipq807x/files/95_apply_bootconfig

@@ -2,6 +2,7 @@ apply_bootconfig() {
 	. /lib/functions.sh
 
 	case $(board_name) in
+	zyxel,nwa110ax|\
 	zyxel,nwa210ax)
 		status="$(zyxel-bootconfig-ipq807x show | awk '/image0:/ {print $2}')"
 		[ "$status" != "selected" ] && zyxel-bootconfig-ipq807x --force set image0

target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8070-nwa110ax.dts

@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2026 Michael Lotz <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "ipq807x-nwax10ax.dtsi"
+
+/ {
+	model = "Zyxel NWA110AX";
+	compatible = "zyxel,nwa110ax", "qcom,ipq8074";
+
+	aliases {
+		ethernet0 = &dp1;
+		label-mac-device = &dp1;
+	};
+};
+
+&switch {
+	switch_lan_bmp = <ESS_PORT1>;
+	switch_mac_mode = <MAC_MODE_SGMII0_RGMII4>;
+};
+
+&dp1 {
+	label = "uplink";
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&label_mac 0>;
+};
+
+&wifi {
+	qcom,ath11k-calibration-variant = "Zyxel-NWA110AX";
+};

target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8071-nwa210ax.dts

@@ -6,43 +6,18 @@
 
 /dts-v1/;
 
-#include "ipq8074.dtsi"
-#include "ipq8074-ac-cpu.dtsi"
-#include "ipq8074-ess.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
+#include "ipq807x-nwax10ax.dtsi"
 
 / {
 	model = "Zyxel NWA210AX";
 	compatible = "zyxel,nwa210ax", "qcom,ipq8074";
 
 	aliases {
-		led-boot = &lp5562_blue;
-		led-failsafe = &lp5562_white;
-		led-running = &lp5562_green;
-		led-upgrade = &lp5562_red;
-		serial0 = &blsp1_uart5;
 		ethernet0 = &dp5;
 		ethernet1 = &dp1;
 		label-mac-device = &dp5;
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-		bootargs-append = " root=/dev/ubiblock0_1";
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		reset {
-			label = "reset";
-			gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_RESTART>;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -60,98 +35,32 @@
 			function = LED_FUNCTION_STATUS;
 		};
 	};
-
-	watchdog {
-		compatible = "linux,wdt-gpio";
-		gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
-		hw_algo = "toggle";
-		hw_margin_ms = <10000>;
-		always-running;
-	};
-};
-
-&blsp1_uart5 {
-	status = "okay";
-};
-
-&crypto {
-	status = "okay";
-};
-
-&edma {
-	status = "okay";
 };
 
 &tlmm {
-	mdio_pins: mdio-pins {
-		mdc {
-			pins = "gpio68";
-			function = "mdc";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-
-		mdio {
-			pins = "gpio69";
-			function = "mdio";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-	};
-
-	mdio_gpio_pins: mdio-gpio-pins {
-		pins = "gpio37", "gpio44";
-		function = "gpio";
-		bias-pull-up;
-	};
-
 	button_pins: button-pins {
 		pins = "gpio30";
 		function = "gpio";
 		drive-strength = <8>;
 		bias-pull-up;
 	};
-
-	i2c_6_pins: i2c-6-state {
-		pins = "gpio0", "gpio2";
-		drive-strength = <8>;
-		function = "blsp5_i2c";
-		bias-disable;
-	};
 };
 
 &switch {
-	status = "okay";
-
 	switch_lan_bmp = <(ESS_PORT1 | ESS_PORT5)>;
 	switch_mac_mode = <MAC_MODE_SGMII_CHANNEL0>;
 	switch_mac_mode1 = <MAC_MODE_SGMII_PLUS>;
+};
 
-	qcom,port_phyinfo {
-		port@1 {
-			port_id = <1>;
-			phy_address = <1>;
-		};
-
-		port@5 {
-			port_id = <5>;
-			phy_address = <16>;
-			port_mac_sel = "QGMAC_PORT";
-		};
+&phyinfo {
+	port@5 {
+		port_id = <5>;
+		phy_address = <16>;
+		port_mac_sel = "QGMAC_PORT";
 	};
 };
 
 &mdio {
-	status = "okay";
-	pinctrl-0 = <&mdio_pins>;
-	pinctrl-names = "default";
-	reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
-
-	ar8033: ethernet-phy@1 {
-		compatible = "ethernet-phy-id004d.074";
-		reg = <1>;
-	};
-
 	qca8081: ethernet-phy@16 {
 		compatible = "ethernet-phy-id004d.d101";
 		reg = <16>;
@@ -161,9 +70,6 @@
 };
 
 &dp1 {
-	status = "okay";
-	phy-handle = <&ar8033>;
-	phy-mode = "sgmii";
 	label = "lan1";
 	nvmem-cell-names = "mac-address";
 	nvmem-cells = <&label_mac 1>;
@@ -178,260 +84,6 @@
 	nvmem-cells = <&label_mac 0>;
 };
 
-&blsp1_spi1 {
-	pinctrl-0 = <&spi_0_pins>;
-	pinctrl-names = "default";
-	cs-select = <0>;
-	status = "okay";
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		reg = <0>;
-		linux,modalias = "m25p80", "n25q128a11";
-		spi-max-frequency = <50000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "0:sbl1";
-				reg = <0x0 0x50000>;
-				read-only;
-			};
-
-			partition@50000 {
-				label = "0:mibib";
-				reg = <0x50000 0x10000>;
-				read-only;
-			};
-
-			partition@60000 {
-				label = "0:bootconfig";
-				reg = <0x60000 0x20000>;
-			};
-
-			partition@80000 {
-				label = "0:bootconfig1";
-				reg = <0x80000 0x20000>;
-			};
-
-			partition@a0000 {
-				label = "0:qsee";
-				reg = <0xa0000 0x180000>;
-				read-only;
-			};
-
-			partition@220000 {
-				label = "0:qsee_1";
-				reg = <0x220000 0x180000>;
-				read-only;
-			};
-
-			partition@3a0000 {
-				label = "0:devcfg";
-				reg = <0x3a0000 0x10000>;
-				read-only;
-			};
-
-			partition@3b0000 {
-				label = "0:devcfg_1";
-				reg = <0x3b0000 0x10000>;
-				read-only;
-			};
-
-			partition@3c0000 {
-				label = "0:apdp";
-				reg = <0x3c0000 0x10000>;
-				read-only;
-			};
-
-			partition@3d0000 {
-				label = "0:apdp_1";
-				reg = <0x3d0000 0x10000>;
-				read-only;
-			};
-
-			partition@3e0000 {
-				label = "0:rpm";
-				reg = <0x3e0000 0x40000>;
-				read-only;
-			};
-
-			partition@420000 {
-				label = "0:rpm_1";
-				reg = <0x420000 0x40000>;
-				read-only;
-			};
-
-			partition@460000 {
-				label = "0:cdt";
-				reg = <0x460000 0x10000>;
-				read-only;
-			};
-
-			partition@470000 {
-				label = "0:cdt_1";
-				reg = <0x470000 0x10000>;
-				read-only;
-			};
-
-			partition@480000 {
-				label = "0:appsblenv";
-				reg = <0x480000 0x10000>;
-				read-only;
-			};
-
-			partition@490000 {
-				label = "0:appsbl";
-				reg = <0x490000 0xa0000>;
-				read-only;
-			};
-
-			partition@530000 {
-				label = "0:appsbl_1";
-				reg = <0x530000 0xa0000>;
-				read-only;
-			};
-
-			partition@5d0000 {
-				label = "0:art";
-				reg = <0x5d0000 0x40000>;
-				read-only;
-			};
-
-			partition@610000 {
-				label = "mrd";
-				reg = <0x610000 0x10000>;
-				read-only;
-
-				nvmem-layout {
-					compatible = "fixed-layout";
-					#address-cells = <1>;
-					#size-cells = <1>;
-
-					label_mac: macaddr@fff8 {
-						compatible = "mac-base";
-						reg = <0xfff8 0x6>;
-						#nvmem-cell-cells = <1>;
-					};
-				};
-			};
-
-			partition@620000 {
-				label = "mrd_1";
-				reg = <0x620000 0x10000>;
-				read-only;
-			};
-
-			partition@630000 {
-				label = "conf";
-				reg = <0x630000 0x1d0000>;
-				read-only;
-			};
-		};
-	};
-};
-
-&qpic_bam {
-	status = "okay";
-};
-
-&qpic_nand {
-	status = "okay";
-
-	nand@0 {
-		reg = <0>;
-		nand-ecc-step-size = <512>;
-		nand-bus-width = <8>;
-		nand-ecc-strength = <4>;
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			reg = <0x00 0x3c00000>;
-			label = "rootfs";
-		};
-
-		partition@3c00000 {
-			reg = <0x3c00000 0x800000>;
-			label = "0:wififw";
-			read-only;
-		};
-
-		partition@4400000 {
-			reg = <0x4400000 0x3c00000>;
-			label = "rootfs_1";
-		};
-
-		partition@8000000 {
-			reg = <0x8000000 0x800000>;
-			label = "0:wififw_1";
-			read-only;
-		};
-
-		partition@8800000 {
-			reg = <0x8800000 0x7800000>;
-			label = "logs";
-		};
-	};
-};
-
 &wifi {
-	status = "okay";
 	qcom,ath11k-calibration-variant = "Zyxel-NWA210AX";
 };
-
-&blsp1_i2c6 {
-	pinctrl-0 = <&i2c_6_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	lp5562@30 {
-		compatible = "ti,lp5562";
-		reg = <0x30>;
-		clock-mode = [02];
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		lp5562_red: led@0 {
-			chan-name = "lp5562_red";
-			led-cur = [20];
-			max-cur = [60];
-			color = <LED_COLOR_ID_RED>;
-			function = LED_FUNCTION_STATUS;
-			reg = <0>;
-		};
-
-		lp5562_green: led@1 {
-			chan-name = "lp5562_green";
-			led-cur = [20];
-			max-cur = [60];
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_STATUS;
-			reg = <1>;
-		};
-
-		lp5562_blue: led@2 {
-			chan-name = "lp5562_blue";
-			led-cur = [20];
-			max-cur = [60];
-			color = <LED_COLOR_ID_BLUE>;
-			function = LED_FUNCTION_STATUS;
-			reg = <2>;
-		};
-
-		lp5562_white: led@3 {
-			chan-name = "lp5562_white";
-			led-cur = [20];
-			max-cur = [60];
-			color = <LED_COLOR_ID_WHITE>;
-			function = LED_FUNCTION_STATUS;
-			reg = <3>;
-		};
-	};
-};

target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq807x-nwax10ax.dtsi

@@ -0,0 +1,375 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2025 Pascal Beleiu <[email protected]>
+ * Copyright (c) 2025 Eric Schäfer <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-ac-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		led-boot = &lp5562_blue;
+		led-failsafe = &lp5562_white;
+		led-running = &lp5562_green;
+		led-upgrade = &lp5562_red;
+		serial0 = &blsp1_uart5;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " root=/dev/ubiblock0_1 loglevel=7";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	watchdog {
+		compatible = "linux,wdt-gpio";
+		gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+		hw_algo = "toggle";
+		hw_margin_ms = <10000>;
+		always-running;
+	};
+};
+
+&blsp1_uart5 {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&edma {
+	status = "okay";
+};
+
+&tlmm {
+	mdio_pins: mdio-pins {
+		mdc {
+			pins = "gpio68";
+			function = "mdc";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		mdio {
+			pins = "gpio69";
+			function = "mdio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	mdio_gpio_pins: mdio-gpio-pins {
+		pins = "gpio37", "gpio44";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	i2c_6_pins: i2c-6-state {
+		pins = "gpio0", "gpio2";
+		drive-strength = <8>;
+		function = "blsp5_i2c";
+		bias-disable;
+	};
+};
+
+&switch {
+	status = "okay";
+
+	phyinfo: qcom,port_phyinfo {
+		port@1 {
+			port_id = <1>;
+			phy_address = <1>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+	ar8033: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&dp1 {
+	status = "okay";
+	phy-handle = <&ar8033>;
+	phy-mode = "sgmii";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-select = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "0:sbl1";
+				reg = <0x0 0x50000>;
+				read-only;
+			};
+
+			partition@50000 {
+				label = "0:mibib";
+				reg = <0x50000 0x10000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "0:bootconfig";
+				reg = <0x60000 0x20000>;
+			};
+
+			partition@80000 {
+				label = "0:bootconfig1";
+				reg = <0x80000 0x20000>;
+			};
+
+			partition@a0000 {
+				label = "0:qsee";
+				reg = <0xa0000 0x180000>;
+				read-only;
+			};
+
+			partition@220000 {
+				label = "0:qsee_1";
+				reg = <0x220000 0x180000>;
+				read-only;
+			};
+
+			partition@3a0000 {
+				label = "0:devcfg";
+				reg = <0x3a0000 0x10000>;
+				read-only;
+			};
+
+			partition@3b0000 {
+				label = "0:devcfg_1";
+				reg = <0x3b0000 0x10000>;
+				read-only;
+			};
+
+			partition@3c0000 {
+				label = "0:apdp";
+				reg = <0x3c0000 0x10000>;
+				read-only;
+			};
+
+			partition@3d0000 {
+				label = "0:apdp_1";
+				reg = <0x3d0000 0x10000>;
+				read-only;
+			};
+
+			partition@3e0000 {
+				label = "0:rpm";
+				reg = <0x3e0000 0x40000>;
+				read-only;
+			};
+
+			partition@420000 {
+				label = "0:rpm_1";
+				reg = <0x420000 0x40000>;
+				read-only;
+			};
+
+			partition@460000 {
+				label = "0:cdt";
+				reg = <0x460000 0x10000>;
+				read-only;
+			};
+
+			partition@470000 {
+				label = "0:cdt_1";
+				reg = <0x470000 0x10000>;
+				read-only;
+			};
+
+			partition@480000 {
+				label = "0:appsblenv";
+				reg = <0x480000 0x10000>;
+				read-only;
+			};
+
+			partition@490000 {
+				label = "0:appsbl";
+				reg = <0x490000 0xa0000>;
+				read-only;
+			};
+
+			partition@530000 {
+				label = "0:appsbl_1";
+				reg = <0x530000 0xa0000>;
+				read-only;
+			};
+
+			partition@5d0000 {
+				label = "0:art";
+				reg = <0x5d0000 0x40000>;
+				read-only;
+			};
+
+			partition@610000 {
+				label = "mrd";
+				reg = <0x610000 0x10000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					label_mac: macaddr@fff8 {
+						compatible = "mac-base";
+						reg = <0xfff8 0x6>;
+						#nvmem-cell-cells = <1>;
+					};
+				};
+			};
+
+			partition@620000 {
+				label = "mrd_1";
+				reg = <0x620000 0x10000>;
+				read-only;
+			};
+
+			partition@630000 {
+				label = "conf";
+				reg = <0x630000 0x1d0000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		nand-ecc-strength = <4>;
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			reg = <0x00 0x3c00000>;
+			label = "rootfs";
+		};
+
+		partition@3c00000 {
+			reg = <0x3c00000 0x800000>;
+			label = "0:wififw";
+			read-only;
+		};
+
+		partition@4400000 {
+			reg = <0x4400000 0x3c00000>;
+			label = "rootfs_1";
+		};
+
+		partition@8000000 {
+			reg = <0x8000000 0x800000>;
+			label = "0:wififw_1";
+			read-only;
+		};
+
+		partition@8800000 {
+			reg = <0x8800000 0x7800000>;
+			label = "logs";
+		};
+	};
+};
+
+&wifi {
+	status = "okay";
+};
+
+&blsp1_i2c6 {
+	pinctrl-0 = <&i2c_6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	lp5562@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		clock-mode = [02];
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		lp5562_red: led@0 {
+			chan-name = "lp5562_red";
+			led-cur = [20];
+			max-cur = [60];
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+			reg = <0>;
+		};
+
+		lp5562_green: led@1 {
+			chan-name = "lp5562_green";
+			led-cur = [20];
+			max-cur = [60];
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			reg = <1>;
+		};
+
+		lp5562_blue: led@2 {
+			chan-name = "lp5562_blue";
+			led-cur = [20];
+			max-cur = [60];
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			reg = <2>;
+		};
+
+		lp5562_white: led@3 {
+			chan-name = "lp5562_white";
+			led-cur = [20];
+			max-cur = [60];
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_STATUS;
+			reg = <3>;
+		};
+	};
+};

target/linux/qualcommax/image/ipq807x.mk

@@ -1,4 +1,4 @@
-DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID TPLINK_SUPPORT_STRING
+DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID TPLINK_SUPPORT_STRING ZYXEL_MODEL_ID
 
 define Build/asus-fake-ramdisk
 	rm -rf $(KDIR)/tmp/fakerd
@@ -44,9 +44,9 @@ define Build/wax6xx-netgear-tar
 	rm -rf [email protected]
 endef
 
-define Build/zyxel-nwa210ax-fit
+define Build/zyxel-nwax10ax-fit
 	$(TOPDIR)/scripts/mkits-zyxel-fit-filogic.sh \
-		[email protected] $@ "5c e1 ff ff ff ff ff ff ff ff"
+		[email protected] $@ "$(ZYXEL_MODEL_ID) ff ff ff ff ff ff ff ff"
 	PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f [email protected] [email protected]
 	@mv [email protected] $@
 endef
@@ -604,18 +604,33 @@ define Device/zyxel_nbg7815
 endef
 TARGET_DEVICES += zyxel_nbg7815
 
-define Device/zyxel_nwa210ax
+define Device/zyxel_nwax10ax_common
 	$(call Device/FitImage)
 	$(call Device/UbiFit)
-	DEVICE_VENDOR := ZYXEL
-	DEVICE_MODEL := NWA210AX
-	DEVICE_DTS_CONFIG := config@ac02
-	SOC := ipq8071
-	DEVICE_PACKAGES := ipq-wifi-zyxel_nwa210ax zyxel-bootconfig-ipq807x kmod-leds-lp5562
+	DEVICE_VENDOR := Zyxel
 	BLOCKSIZE := 128k
 	PAGESIZE := 2048
 	IMAGE_SIZE := 61440k
 	IMAGES += factory.bin
-	IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) | zyxel-nwa210ax-fit
+	IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) | zyxel-nwax10ax-fit
+endef
+
+define Device/zyxel_nwa110ax
+	$(call Device/zyxel_nwax10ax_common)
+	DEVICE_MODEL := NWA110AX
+	DEVICE_DTS_CONFIG := config@ac01
+	SOC := ipq8070
+	DEVICE_PACKAGES := ipq-wifi-zyxel_nwa110ax zyxel-bootconfig-ipq807x kmod-leds-lp5562
+	ZYXEL_MODEL_ID := 59 e1
+endef
+TARGET_DEVICES += zyxel_nwa110ax
+
+define Device/zyxel_nwa210ax
+	$(call Device/zyxel_nwax10ax_common)
+	DEVICE_MODEL := NWA210AX
+	DEVICE_DTS_CONFIG := config@ac02
+	SOC := ipq8071
+	DEVICE_PACKAGES := ipq-wifi-zyxel_nwa210ax zyxel-bootconfig-ipq807x kmod-leds-lp5562
+	ZYXEL_MODEL_ID := 5c e1
 endef
 TARGET_DEVICES += zyxel_nwa210ax

target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network

@@ -74,6 +74,9 @@ ipq807x_setup_interfaces()
 	zyxel,nbg7815)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g" "wan"
 		;;
+	zyxel,nwa110ax)
+		ucidef_set_interface_lan "uplink" "dhcp"
+		;;
 	zyxel,nwa210ax)
 		ucidef_set_interface_lan "uplink lan1" "dhcp"
 		;;
@@ -110,6 +113,7 @@ ipq807x_setup_macs()
 		label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
 		lan_mac=$label_mac
 		;;
+	zyxel,nwa110ax|\
 	zyxel,nwa210ax)
 		label_mac=$(get_mac_label_dt)
 		lan_mac=$label_mac

target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata

@@ -141,6 +141,13 @@ case "$FIRMWARE" in
 		ath11k_patch_mac $(macaddr_add $label_mac 4) 2
 		ath11k_set_macflag
 		;;
+	zyxel,nwa110ax)
+		caldata_extract "0:art" 0x1000 0x20000
+		label_mac=$(get_mac_label)
+		ath11k_patch_mac $(macaddr_add $label_mac 2) 0
+		ath11k_patch_mac $(macaddr_add $label_mac 1) 1
+		ath11k_set_macflag
+		;;
 	zyxel,nwa210ax)
 		caldata_extract "0:art" 0x1000 0x20000
 		label_mac=$(get_mac_label)

target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh

@@ -187,6 +187,7 @@ platform_do_upgrade() {
 	netgear,wax218|\
 	netgear,wax620|\
 	netgear,wax630|\
+	zyxel,nwa110ax|\
 	zyxel,nwa210ax)
 		nand_do_upgrade "$1"
 		;;