mvebu: update and refactor uDPU DTS

uDPU DTS has pending upstream fixups, so backport those as well as split
the DTS into a DTSI and DTS in preparation for euroDPU support which
uses uDPU as the base.

Ethernet aliases have not yet been sent upstream but will be soon in order
for U-boot to set the correct MAC on both ethernet interfaces instead of
just one.

Since U-boot environment now has its own partition, update the envtools
config script to search for it instead.

Patch hardcoding PHY mode is also not applicable anymore, so drop it and
set in the uDPU DTS directly.

Signed-off-by: Robert Marko <[email protected]>

package/boot/uboot-envtools/files/mvebu

@@ -59,7 +59,12 @@ linksys,wrt32x)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
 	;;
 methode,udpu)
+	idx="$(find_mtd_index u-boot-env)"
+	if [ -n "$idx" ]; then
+	ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000" "1"
+	else
 	ubootenv_add_uci_config "/dev/mtd0" "0x180000" "0x10000" "0x10000"
+	fi
 	;;
 esac
 

target/linux/mvebu/files/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts

@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "armada-3720-uDPU.dtsi"
+
+/ {
+	model = "Methode uDPU Board";
+	compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";
+
+	sfp_eth0: sfp-eth0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c0>;
+		los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <3000>;
+	};
+};
+
+&pinctrl_nb {
+	i2c1_recovery_pins: i2c1-recovery-pins {
+		groups = "i2c1";
+		function = "gpio";
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default", "recovery";
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-1 = <&i2c1_recovery_pins>;
+	/delete-property/mrvl,i2c-fast-mode;
+	scl-gpios = <&gpionb 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&eth0 {
+	phy-mode = "2500base-x";
+	sfp = <&sfp_eth0>;
+};
+
+&eth1 {
+	phy-mode = "2500base-x";
+};

target/linux/mvebu/files/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi

@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ * Vladimir Vid <[email protected]>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power1 {
+			label = "udpu:green:power";
+			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power2 {
+			label = "udpu:red:power";
+			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-network1 {
+			label = "udpu:green:network";
+			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-network2 {
+			label = "udpu:red:network";
+			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-alarm1 {
+			label = "udpu:green:alarm";
+			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-alarm2 {
+			label = "udpu:red:alarm";
+			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sfp_eth1: sfp-eth1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <3000>;
+	};
+};
+
+&sdhci0 {
+	status = "okay";
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	marvell,pad-type = "fixed-1-8v";
+	non-removable;
+	no-sd;
+	no-sdio;
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_quad_pins>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <54000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "firmware";
+				reg = <0x0 0x180000>;
+			};
+
+			partition@180000 {
+				label = "u-boot-env";
+				reg = <0x180000 0x10000>;
+			};
+		};
+	};
+};
+
+&pinctrl_nb {
+	i2c2_recovery_pins: i2c2-recovery-pins {
+		groups = "i2c2";
+		function = "gpio";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default", "recovery";
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-1 = <&i2c2_recovery_pins>;
+	/delete-property/mrvl,i2c-fast-mode;
+	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	temp-sensor@48 {
+		compatible = "ti,tmp75c";
+		reg = <0x48>;
+	};
+
+	temp-sensor@49 {
+		compatible = "ti,tmp75c";
+		reg = <0x49>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	managed = "in-band-status";
+	phys = <&comphy1 0>;
+};
+
+&eth1 {
+	phy-mode = "sgmii";
+	status = "okay";
+	managed = "in-band-status";
+	phys = <&comphy0 1>;
+	sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+	status = "okay";
+	phys = <&usb2_utmi_otg_phy>;
+	phy-names = "usb2-utmi-otg-phy";
+};
+
+&uart0 {
+	status = "okay";
+};

target/linux/mvebu/patches-5.10/314-arm64-dts-uDPU-switch-PHY-operation-mode-to-2500base.patch

@@ -1,34 +0,0 @@
-Certain SFP modules (most notably Nokia GPON ones) first check
-connectivity on 1000base-x, and switch to 2500base-x afterwards. This
-is considered a quirk so the phylink switches the interface to
-2500base-x as well.
-
-However, after power-cycling the uDPU device, network interface/SFP module
-will not work correctly until the module is re-seated. This patch
-resolves this issue by forcing the interface to be brought up in
-2500base-x mode by default.
-
-Signed-off-by: Jakov Petrina <[email protected]>
-Signed-off-by: Vladimir Vid <[email protected]>
-Cc: Luka Perkov <[email protected]>
-
---- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
-+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
-@@ -162,7 +162,7 @@
- };
- 
- &eth0 {
--	phy-mode = "sgmii";
-+	phy-mode = "2500base-x";
- 	status = "okay";
- 	managed = "in-band-status";
- 	phys = <&comphy1 0>;
-@@ -170,7 +170,7 @@
- };
- 
- &eth1 {
--	phy-mode = "sgmii";
-+	phy-mode = "2500base-x";
- 	status = "okay";
- 	managed = "in-band-status";
- 	phys = <&comphy0 1>;