ramips: add support for the HNET C108

The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:

* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.

Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).

Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.

Not tested:
* SD card reader.

Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.

Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.

Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.

Signed-off-by: Kristian Evensen <[email protected]>

target/linux/ramips/base-files/etc/board.d/01_leds

@@ -82,6 +82,10 @@ broadway)
 	set_usb_led "$board:red:diskmounted"
 	set_wifi_led "$board:red:wps_active"
 	;;
+c108)
+	ucidef_set_led_netdev "lan" "lan" "$board:green:lan" "eth0"
+	ucidef_set_led_netdev "modem" "modem" "$board:green:modem" "wwan0"
+	;;
 c20i)
 	ucidef_set_led_switch "lan" "lan" "$board:blue:lan" "switch0" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$board:blue:wan" "switch0" "0x01"

target/linux/ramips/base-files/etc/board.d/02_network

@@ -217,6 +217,7 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
 		;;
+	c108|\
 	cf-wr800n)
 		ucidef_add_switch "switch0" \
 			"4:lan" "6t@eth0"

target/linux/ramips/base-files/etc/diag.sh

@@ -103,6 +103,9 @@ get_status_led() {
 	wrh-300cr)
 		status_led="$board:green:wps"
 		;;
+	c108)
+		status_led="$board:green:lan"
+		;;
 	cf-wr800n|\
 	psg1208)
 		status_led="$board:white:wps"

target/linux/ramips/base-files/lib/ramips.sh

@@ -85,6 +85,9 @@ ramips_board_detect() {
 	*"Broadway")
 		name="broadway"
 		;;
+	*"C108")
+		name="c108"
+		;;
 	*"C20i")
 		name="c20i"
 		;;

target/linux/ramips/base-files/lib/upgrade/platform.sh

@@ -29,6 +29,7 @@ platform_check_image() {
 	awm002-evb-8M|\
 	bc2|\
 	broadway|\
+	c108|\
 	carambola|\
 	cf-wr800n|\
 	cs-qr10|\

target/linux/ramips/dts/C108.dts

@@ -0,0 +1,177 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2017 Kristian Evensen <[email protected]>.
+ *  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "hnet,c108", "ralink,mt7620a-soc";
+	model = "HNET C108";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	gpio-export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		power_modem {
+			gpio-export,name = "power_modem";
+			gpio-export,output = <1>;
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		sdcard {
+			label = "c108:green:sdcard";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		modem_green {
+			label = "c108:green:modem";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		modem_red {
+			label = "c108:red:modem";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		lan_red {
+			label = "c108:red:lan";
+			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		lan_green {
+			label = "c108:green:lan";
+			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+
+		reset {
+			label = "reset";
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	en25q128@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+
+		partition@30000 {
+			label = "u-boot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+
+		factory: partition@40000 {
+			label = "factory";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+
+		partition@50000 {
+			label = "firmware";
+			reg = <0x50000 0xfb0000>;
+		};
+	};
+};
+
+&sdhci {
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0x28>;
+};
+
+&wmac {
+	ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pinctrl {
+	state_default: pinctrl0 {
+		default {
+			ralink,group = "i2c", "uartf", "spi refclk", "ephy";
+			ralink,function = "gpio";
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};

target/linux/ramips/image/mt7620.mk

@@ -62,6 +62,14 @@ define Device/ArcherMR200
 endef
 TARGET_DEVICES += ArcherMR200
 
+define Device/c108
+  DTS := C108
+  IMAGE_SIZE := 16777216
+  DEVICE_TITLE := HNET C108
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620
+endef
+TARGET_DEVICES += c108
+
 define Device/cf-wr800n
   DTS := CF-WR800N
   DEVICE_TITLE := Comfast CF-WR800N