ramips: add support for TP-Link Archer C2

Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <[email protected]>
Signed-off-by: Franz Flasch <[email protected]>

target/linux/ramips/base-files/etc/board.d/01_leds

@@ -398,6 +398,12 @@ tl-wr841n-v13)
 	ucidef_set_led_switch "lan4" "lan4" "$boardname:green:lan4" "switch0" "0x10"
 	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
 	;;
+tplink,c2-v1)
+	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch1" "0x1e"
+	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch1" "0x01"
+	set_usb_led "$boardname:green:usb" "2-1"
+	set_wifi_led "$boardname:green:wlan"
+	;;
 tplink,c20-v1)
 	ucidef_set_led_switch "lan" "lan" "$boardname:blue:lan" "switch0" "0x1e"
 	ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x01"

target/linux/ramips/base-files/etc/board.d/02_network

@@ -335,6 +335,10 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
 		;;
+	tplink,c2-v1)
+		ucidef_add_switch "switch1" \
+			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
+		;;
 	tplink,tl-wr902ac-v3)
 		ucidef_add_switch "switch0" \
 			"4:lan" "6@eth0"

target/linux/ramips/base-files/etc/diag.sh

@@ -79,6 +79,7 @@ get_status_led() {
 	awapn2403|\
 	dir-645|\
 	sk-wb8|\
+	tplink,c2-v1|\
 	wrh-300cr)
 		status_led="$boardname:green:wps"
 		;;

target/linux/ramips/base-files/lib/upgrade/platform.sh

@@ -253,6 +253,7 @@ platform_check_image() {
 	c20i|\
 	c50|\
 	mr200|\
+	tplink,c2-v1|\
 	tplink,c20-v1|\
 	tplink,c20-v4|\
 	tplink,c50-v3|\

target/linux/ramips/dts/ArcherC2-v1.dts

@@ -0,0 +1,178 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "tplink,c2-v1", "ralink,mt7620a-soc";
+	model = "TP-Link Archer C2 v1";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "uartf", "wled", "ephy", "spi refclk";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		lan {
+			label = "c2-v1:green:lan";
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+		};
+
+		usb {
+			label = "c2-v1:green:usb";
+			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "c2-v1:green:wps";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		wan {
+			label = "c2-v1:green:wan";
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "c2-v1:green:wlan";
+			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset_wps {
+			label = "reset_wps";
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		rfkill {
+			label = "rfkill";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+	};
+
+	rtl8367rb {
+		compatible = "realtek,rtl8367b", "rtl8367b";
+		cpu_port = <6>;
+		realtek,extif1 = <1 0 1 1 1 1 1 1 2>;
+		mii-bus = <&mdio0>;
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x20000>;
+			read-only;
+		};
+
+		partition@20000 {
+			label = "firmware";
+			reg = <0x20000 0x7a0000>;
+		};
+
+		partition@7c0000 {
+			label = "config";
+			reg = <0x7c0000 0x10000>;
+			read-only;
+		};
+
+		rom: partition@7d0000 {
+			label = "rom";
+			reg = <0x7d0000 0x10000>;
+			read-only;
+		};
+
+		partition@7e0000 {
+			label = "romfile";
+			reg = <0x7e0000 0x10000>;
+			read-only;
+		};
+
+		radio: partition@7f0000 {
+			label = "radio";
+			reg = <0x7f0000 0x10000>;
+			read-only;
+		};
+	};
+};
+
+&ethernet {
+	status = "okay";
+	mtd-mac-address = <&rom 0xf100>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
+
+	port@5 {
+		status = "okay";
+		mediatek,fixed-link = <1000 1 1 1>;
+		phy-mode = "rgmii";
+	};
+
+	mdio0: mdio-bus {
+		status = "okay";
+	};
+};
+
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&wmac {
+	ralink,mtd-eeprom = <&radio 0>;
+	mtd-mac-address = <&rom 0xf100>;
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+
+	pcie-bridge {
+		mt76@0,0 {
+			reg = <0x0000 0 0 0 0>;
+			device_type = "pci";
+			mediatek,mtd-eeprom = <&radio 0x8000>;
+		};
+	};
+};

target/linux/ramips/image/mt7620.mk

@@ -472,6 +472,18 @@ define Device/tiny-ac
 endef
 TARGET_DEVICES += tiny-ac
 
+define Device/tplink_c2-v1
+  $(Device/Archer)
+  DTS := ArcherC2-v1
+  TPLINK_FLASHLAYOUT := 8Mmtk
+  TPLINK_HWID := 0xc7500001
+  TPLINK_HWREV := 50
+  IMAGES += factory.bin
+  DEVICE_TITLE := TP-Link Archer C2 v1
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport kmod-switch-rtl8366-smi kmod-switch-rtl8367b
+endef
+TARGET_DEVICES += tplink_c2-v1
+
 define Device/tplink_c20-v1
   $(Device/Archer)
   DTS := ArcherC20v1