Revert "bcm27xx: bcm27xx: update defconfig"

This reverts all four commits
dbb45421bab "bcm27xx: bcm2708: update defconfig"
332f69583ad "bcm27xx: bcm2709: update defconfig"
a478202d74b "bcm27xx: bcm2710: update defconfig"
82da1dfd69a "bcm27xx: bcm2711: update defconfig"

this also highlighted an unrelated kconfig failure
that warrants investigation. But for now it is important
for the bcm27xx target to come back again.

|*
|* Restart config...
|*
|*
|* Allow override default queue discipline
|*
|Allow override default queue discipline (NET_SCH_DEFAULT) [Y/n/?] y
|  Default queuing discipline
|    1. Fair Queue (DEFAULT_FQ) (NEW)
|    2. Controlled Delay (DEFAULT_CODEL) (NEW)
|  > 3. Fair Queue Controlled Delay (DEFAULT_FQ_CODEL)
|    4. Stochastic Fair Queue (DEFAULT_SFQ) (NEW)
|    5. Priority FIFO Fast (DEFAULT_PFIFO_FAST)
|  choice[1-5?]:
|Error in reading or end of file.

Signed-off-by: Christian Lamparter <[email protected]>

target/linux/bcm27xx/bcm2708/config-5.10

@@ -299,6 +299,7 @@ CONFIG_RESET_CONTROLLER=y
 # CONFIG_RESET_RASPBERRYPI is not set
 CONFIG_RESET_SIMPLE=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_SCSI=y
 # CONFIG_SCSI_LOWLEVEL is not set
@@ -318,6 +319,8 @@ CONFIG_SERIAL_MCTRL_GPIO=y
 CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SG_POOL=y
 CONFIG_SMSC_PHY=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSE_IRQ=y
 CONFIG_SRCU=y
 # CONFIG_STRIP_ASM_SYMS is not set

target/linux/bcm27xx/bcm2709/config-5.10

@@ -376,6 +376,7 @@ CONFIG_RESET_RASPBERRYPI=y
 CONFIG_RESET_SIMPLE=y
 CONFIG_RFS_ACCEL=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_RPS=y
 CONFIG_RWSEM_SPIN_ON_OWNER=y
@@ -399,6 +400,8 @@ CONFIG_SG_POOL=y
 CONFIG_SMP=y
 CONFIG_SMP_ON_UP=y
 CONFIG_SMSC_PHY=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSE_IRQ=y
 CONFIG_SRCU=y
 # CONFIG_STRIP_ASM_SYMS is not set

target/linux/bcm27xx/bcm2710/config-5.10

@@ -37,6 +37,8 @@ CONFIG_ARM64_VA_BITS=39
 CONFIG_ARM64_VA_BITS_39=y
 CONFIG_ARM64_VHE=y
 CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y
+CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y
+CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y
 CONFIG_ARM_AMBA=y
 CONFIG_ARM_ARCH_TIMER=y
 CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
@@ -362,6 +364,7 @@ CONFIG_RESET_SIMPLE=y
 CONFIG_RFS_ACCEL=y
 CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_RPS=y
 CONFIG_RWSEM_SPIN_ON_OWNER=y
@@ -384,6 +387,8 @@ CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SG_POOL=y
 CONFIG_SMP=y
 CONFIG_SMSC_PHY=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSEMEM=y
 CONFIG_SPARSEMEM_EXTREME=y
 CONFIG_SPARSEMEM_MANUAL=y

target/linux/bcm27xx/bcm2711/config-5.10

@@ -37,6 +37,8 @@ CONFIG_ARM64_VA_BITS=39
 CONFIG_ARM64_VA_BITS_39=y
 CONFIG_ARM64_VHE=y
 CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y
+CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y
+CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y
 CONFIG_ARM_AMBA=y
 CONFIG_ARM_ARCH_TIMER=y
 CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
@@ -374,6 +376,7 @@ CONFIG_RESET_SIMPLE=y
 CONFIG_RFS_ACCEL=y
 CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_RPS=y
 CONFIG_RWSEM_SPIN_ON_OWNER=y
@@ -395,6 +398,8 @@ CONFIG_SERIAL_MCTRL_GPIO=y
 CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SG_POOL=y
 CONFIG_SMP=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSEMEM=y
 CONFIG_SPARSEMEM_EXTREME=y
 CONFIG_SPARSEMEM_MANUAL=y