ramips: add support for Intenso Memory 2 Move USB 3.0

This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.

The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]

Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).

Signed-off-by: Christian Lamparter <[email protected]>

SVN-Revision: 44001

target/linux/ramips/base-files/etc/board.d/01_leds

@@ -152,6 +152,10 @@ case $board in
 	nw718)
 		set_usb_led "nw718:amber:usb"
 		;;
+	m2m)
+		set_wifi_led "m2m:blue:wifi"
+		ucidef_set_led_netdev "eth" "Ethernet" "m2m:green:wan" "eth0"
+		;;
 	omni-emb-hpm)
 		ucidef_set_led_default "power" "POWER" "emb:orange:power" "1"
 		ucidef_set_led_netdev "eth" "ETH" "emb:green:eth" "eth0"

target/linux/ramips/base-files/etc/board.d/02_network

@@ -65,6 +65,11 @@ ramips_setup_interfaces()
 		ucidef_set_interface_lan "eth0.1"
 		;;
 
+	m2m)
+		ucidef_add_switch "switch0" "4"
+		ucidef_set_interface_lan "eth0"
+		;;
+
 	wizard8800 | \
 	wl-330n | \
 	wmr300)

target/linux/ramips/base-files/etc/diag.sh

@@ -79,6 +79,9 @@ get_status_led() {
 	hw550-3g)
 		status_led="hw550-3g:green:status"
 		;;
+	m2m)
+		status_led="m2m:blue:wifi"
+		;;
 	m3)
 		status_led="m3:blue:status"
 		;;

target/linux/ramips/base-files/lib/ramips.sh

@@ -214,6 +214,9 @@ ramips_board_detect() {
 	*"NW718")
 		name="nw718"
 		;;
+	*"Intenso Memory 2 Move")
+		name="m2m"
+		;;
 	*"Omnima EMB HPM")
 		name="omni-emb-hpm"
 		;;

target/linux/ramips/base-files/lib/upgrade/platform.sh

@@ -55,6 +55,7 @@ platform_check_image() {
 	ht-tm02 | \
 	hw550-3g | \
 	ip2202 | \
+	m2m | \
 	m3 | \
 	m4 | \
 	mlw221 | \

target/linux/ramips/dts/M2M.dts

@@ -0,0 +1,113 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+	compatible = "M2M", "ralink,rt5350-soc";
+	model = "Intenso Memory 2 Move";
+
+	chosen {
+		bootargs = "console=ttyS1,57600n8 root=/dev/mtdblock5";
+	};
+
+	palmbus@10000000 {
+		uart@500 {
+			status = "okay";
+		};
+
+		spi@b00 {
+			status = "okay";
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "mx25l6405d";
+				reg = <0 0>;
+				linux,modalias = "m25p80", "mx25l6405d";
+				spi-max-frequency = <10000000>;
+
+				partition@0 {
+					label = "Bootloader";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition@30000 {
+					label = "Config";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				factory: partition@40000 {
+					label = "Factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition@50000 {
+					label = "firmware";
+					reg = <0x50000 0x7b0000>;
+				};
+			};
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "jtag", "uartf";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		wifi {
+			label = "m2m:blue:wifi";
+			gpios = <&gpio0 7 1>;
+		};
+		wan {
+			label = "m2m:green:wan";
+			gpios = <&gpio0 12 1>;
+		};
+	};
+
+	gpio-keys-polled {
+		gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+			power {
+				label = "power";
+				gpios = <&gpio0 1 1>;
+				linux,code = <0x116>;
+			};
+			reset {
+				label = "reset";
+				gpios = <&gpio0 10 1>;
+				linux,code = <0x198>;
+			};
+		};
+	};
+
+	ethernet@10100000 {
+		mtd-mac-address = <&factory 0x28>;
+	};
+
+	esw@10110000 {
+		ralink,portmap = <0x2f>;
+	};
+
+	ehci@101c0000 {
+		status = "okay";
+	};
+
+	ohci@101c1000 {
+		status = "okay";
+	};
+
+	wmac@10180000 {
+		ralink,mtd-eeprom = <&factory 0x0>;
+	};
+};

target/linux/ramips/image/Makefile

@@ -546,6 +546,8 @@ Image/Build/Profile/NCS601W=$(call BuildFirmware/Default8M/$(1),$(1),ncs601W,NCS
 nw718_mtd_size=3801088
 Image/Build/Profile/NW718=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),nw718m,NW718,$(nw718_mtd_size),ARA1B4NCRNW718;1,factory)
 
+Image/Build/Profile/M2M=$(call BuildFirmware/Default8M/$(1),$(1),m2m,M2M,Linux Kernel Image)
+
 Image/Build/Profile/OMNI-EMB=$(call BuildFirmware/Default8M/$(1),$(1),omni-emb,OMNI-EMB)
 
 Image/Build/Profile/OMNI-PLUG=$(call BuildFirmware/Default8M/$(1),$(1),omni-plug,OMNI-PLUG)
@@ -694,6 +696,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/HT-TM02,$(1))
 	$(call Image/Build/Profile/HW550-3G,$(1))
 	$(call Image/Build/Profile/IP2202,$(1))
+	$(call Image/Build/Profile/M2M,$(1))
 	$(call Image/Build/Profile/M3,$(1))
 	$(call Image/Build/Profile/M4,$(1))
 	$(call Image/Build/Profile/MOFI3500-3GN,$(1))

target/linux/ramips/rt305x/profiles/m2m.mk

@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/M2M
+	NAME:=Intenso Memory 2 Move
+	PACKAGES:=\
+		kmod-ledtrig-netdev kmod-ledtrig-timer kmod-leds-gpio \
+		kmod-usb-core kmod-usb2 kmod-usb-storage kmod-scsi-core \
+		kmod-fs-ext4 kmod-fs-vfat block-mount
+endef
+
+define Profile/M2M/Description
+	Package set for Intenso Memory 2 Move USB 3.0
+endef
+
+$(eval $(call Profile,M2M))