kirkwood: remove 5.15 kernel support

Kernel was switched to 6.1. Lets drop 5.15 support.

Signed-off-by: Pawel Dembicki <[email protected]>

target/linux/kirkwood/config-5.15

@@ -1,293 +0,0 @@
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_32BIT_OFF_T=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_KEEP_MEMBLOCK=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_CPU_AUTO=y
-# CONFIG_ARCH_MULTI_V4 is not set
-# CONFIG_ARCH_MULTI_V4T is not set
-CONFIG_ARCH_MULTI_V4_V5=y
-CONFIG_ARCH_MULTI_V5=y
-CONFIG_ARCH_MVEBU=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
-CONFIG_ARCH_SELECT_MEMORY_MODEL=y
-CONFIG_ARCH_SPARSEMEM_ENABLE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARM=y
-# CONFIG_ARMADA_37XX_WATCHDOG is not set
-# CONFIG_ARMADA_THERMAL is not set
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
-CONFIG_ARM_CRYPTO=y
-CONFIG_ARM_HAS_SG_CHAIN=y
-# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ARM_UNWIND=y
-CONFIG_ATA=y
-CONFIG_ATAGS=y
-CONFIG_ATA_LEDS=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_BLK_MQ_PCI=y
-CONFIG_CACHE_FEROCEON_L2=y
-# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_COMMON_CLK=y
-CONFIG_COMPAT_32BIT_TIME=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_FEROCEON=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FEROCEON=y
-# CONFIG_CPU_FEROCEON_OLD_ID is not set
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_THERMAL=y
-CONFIG_CPU_THUMB_CAPABLE=y
-CONFIG_CPU_TLB_FEROCEON=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC16=y
-# CONFIG_CRC32_SARWATE is not set
-CONFIG_CRC32_SLICEBY8=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_DEV_MARVELL=y
-CONFIG_CRYPTO_DEV_MARVELL_CESA=y
-CONFIG_CRYPTO_HASH_INFO=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
-CONFIG_CRYPTO_LIB_DES=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_ZSTD=y
-CONFIG_DEBUG_LL=y
-CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
-CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y
-# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
-CONFIG_DEBUG_UART_8250=y
-CONFIG_DEBUG_UART_8250_SHIFT=2
-CONFIG_DEBUG_UART_PHYS=0xf1012000
-CONFIG_DEBUG_UART_VIRT=0xfed12000
-CONFIG_DEBUG_UNCOMPRESS=y
-CONFIG_DMA_OPS=y
-CONFIG_DMA_REMAP=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-# CONFIG_EARLY_PRINTK is not set
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_FIXED_PHY=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FORCE_PCI=y
-CONFIG_FWNODE_MDIO=y
-CONFIG_FW_LOADER_PAGED_BUF=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_EARLY_IOREMAP=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GLOB=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_CDEV=y
-CONFIG_GPIO_MVEBU=y
-CONFIG_GRO_CELLS=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-CONFIG_HWMON=y
-CONFIG_HW_RANDOM=y
-CONFIG_HW_RANDOM_OMAP=y
-CONFIG_HZ_FIXED=0
-CONFIG_HZ_PERIODIC=y
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MV64XXX=y
-# CONFIG_I2C_PXA is not set
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_KIRKWOOD_CLK=y
-CONFIG_KIRKWOOD_THERMAL=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_NETXBIG=y
-CONFIG_LEDS_NS2=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_DEBUGGING_SUPPORT=y
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MACH_KIRKWOOD=y
-CONFIG_MACH_MVEBU_ANY=y
-CONFIG_MANGLE_BOOTARGS=y
-CONFIG_MARVELL_PHY=y
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MDIO_DEVRES=y
-CONFIG_MEMFD_CREATE=y
-CONFIG_MIGRATION=y
-CONFIG_MODULES_USE_ELF_REL=y
-# CONFIG_MTD_CFI is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_NAND_CORE=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_ECC_SW_HAMMING=y
-# CONFIG_MTD_NAND_MARVELL is not set
-CONFIG_MTD_NAND_ORION=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_MTD_SPLIT_FIRMWARE=y
-CONFIG_MTD_SPLIT_UIMAGE_FW=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MV643XX_ETH=y
-CONFIG_MVEBU_CLK_COMMON=y
-CONFIG_MVEBU_MBUS=y
-CONFIG_MVMDIO=y
-# CONFIG_MVNETA is not set
-# CONFIG_MVPP2 is not set
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_DEVLINK=y
-CONFIG_NET_DSA=y
-CONFIG_NET_DSA_MV88E6XXX=y
-CONFIG_NET_DSA_TAG_DSA=y
-CONFIG_NET_DSA_TAG_DSA_COMMON=y
-CONFIG_NET_DSA_TAG_EDSA=y
-CONFIG_NET_SELFTESTS=y
-CONFIG_NET_SWITCHDEV=y
-CONFIG_NLS=y
-CONFIG_NVMEM=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_KOBJ=y
-CONFIG_OF_MDIO=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_ORION_IRQCHIP=y
-CONFIG_ORION_TIMER=y
-CONFIG_ORION_WATCHDOG=y
-CONFIG_OUTER_CACHE=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PCI=y
-CONFIG_PCI_BRIDGE_EMUL=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_DOMAINS_GENERIC=y
-CONFIG_PCI_MVEBU=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PHYLINK=y
-# CONFIG_PHY_MVEBU_A3700_UTMI is not set
-# CONFIG_PHY_MVEBU_A38X_COMPHY is not set
-CONFIG_PHY_MVEBU_SATA=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_KIRKWOOD=y
-CONFIG_PINCTRL_MVEBU=y
-# CONFIG_PINCTRL_SINGLE is not set
-CONFIG_PINCTRL_SX150X=y
-CONFIG_PLAT_ORION=y
-CONFIG_POWER_RESET=y
-CONFIG_POWER_RESET_GPIO=y
-CONFIG_POWER_RESET_LINKSTATION=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PTP_1588_CLOCK_OPTIONAL=y
-CONFIG_RATIONAL=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_MV=y
-CONFIG_RTC_I2C_AND_SPI=y
-CONFIG_RTC_MC146818_LIB=y
-CONFIG_SCSI=y
-CONFIG_SCSI_COMMON=y
-CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_MCTRL_GPIO=y
-# CONFIG_SERIAL_MVEBU_UART is not set
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SGL_ALLOC=y
-CONFIG_SG_POOL=y
-CONFIG_SOC_BUS=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPI=y
-# CONFIG_SPI_ARMADA_3700 is not set
-CONFIG_SPI_MASTER=y
-CONFIG_SPI_MEM=y
-CONFIG_SPI_ORION=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SRAM=y
-CONFIG_SRAM_EXEC=y
-CONFIG_SRCU=y
-CONFIG_SWPHY=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_HWMON=y
-CONFIG_THERMAL_OF=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TINY_SRCU=y
-CONFIG_UBIFS_FS=y
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_UNWINDER_ARM=y
-CONFIG_USB=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_LED_TRIG=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-# CONFIG_VFP is not set
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_WAN=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XXHASH=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZSTD_COMPRESS=y
-CONFIG_ZSTD_DECOMPRESS=y

target/linux/kirkwood/patches-5.15/001-5.18-Add-Ctera-C-200-V1-board.patch

@@ -1,350 +0,0 @@
-From 5fc74dbdf8f640a7ca7fb92345ac6fbeaa078d65 Mon Sep 17 00:00:00 2001
-From: Pawel Dembicki <[email protected]>
-Date: Tue, 15 Feb 2022 17:39:22 +0100
-Subject: [PATCH] ARM: dts: kirkwood: Add Ctera C-200 V1 board
-
-Ctera C200 V1 is kirkwood-based 2-Bay NAS.
-
-Hardware:
-  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
-  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
-  - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
-  - Lan: 1x GBE (Marvell 88E1116R-NNC1)
-  - Storage: 2x SATA HDD 3.5" Slot
-  - USB: 2x USB 2.0 port
-  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
-  - LEDs: 13x GPIO controlled
-  - Buttons: 2x GPIO controlled
-
-Signed-off-by: Pawel Dembicki <[email protected]>
-Reviewed-by: Andrew Lunn <[email protected]>
-Signed-off-by: Gregory CLEMENT <[email protected]>
----
- arch/arm/boot/dts/Makefile             |   1 +
- arch/arm/boot/dts/kirkwood-c200-v1.dts | 310 +++++++++++++++++++++++++
- 2 files changed, 311 insertions(+)
- create mode 100644 arch/arm/boot/dts/kirkwood-c200-v1.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -267,6 +267,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
- dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-b3.dtb \
- 	kirkwood-blackarmor-nas220.dtb \
-+	kirkwood-c200-v1.dtb \
- 	kirkwood-cloudbox.dtb \
- 	kirkwood-d2net.dtb \
- 	kirkwood-db-88f6281.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
-@@ -0,0 +1,310 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later
-+/*
-+ * Ctera C200 V1 Board Description
-+ * Copyright 2021-2022 Pawel Dembicki <[email protected]>
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+#include <dt-bindings/leds/common.h>
-+
-+/ {
-+	model = "Ctera C200 V1";
-+	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200";
-+		stdout-path = &uart0;
-+	};
-+
-+	memory@0 {
-+		device_type = "memory";
-+		reg = <0x00000000 0x20000000>;
-+	};
-+
-+	keys {
-+		compatible = "gpio-keys";
-+		pinctrl-0 = <&pmx_buttons>;
-+		pinctrl-names = "default";
-+
-+		power {
-+			label = "Power Button";
-+			linux,code = <KEY_POWER>;
-+			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		reset {
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		usb1 {
-+			label = "USB1 Button";
-+			linux,code = <BTN_0>;
-+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		usb2 {
-+			label = "USB2 Button";
-+			linux,code = <BTN_1>;
-+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	gpio-poweroff {
-+		compatible = "gpio-poweroff";
-+		pinctrl-0 = <&pmx_poweroff>;
-+		pinctrl-names = "default";
-+		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = <&pmx_leds>;
-+		pinctrl-names = "default";
-+
-+		led-0 {
-+			function = LED_FUNCTION_DISK;
-+			function-enumerator = <2>;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-1 {
-+			function = LED_FUNCTION_DISK;
-+			function-enumerator = <1>;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-2 {
-+			function = LED_FUNCTION_DISK;
-+			function-enumerator = <2>;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-3 {
-+			function = LED_FUNCTION_DISK;
-+			function-enumerator = <1>;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-4 {
-+			function = LED_FUNCTION_STATUS;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-5 {
-+			function = LED_FUNCTION_STATUS;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-6 {
-+			function = LED_FUNCTION_INDICATOR;
-+			color = <LED_COLOR_ID_BLUE>;
-+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-7 {
-+			function = LED_FUNCTION_DISK_ERR;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-8 {
-+			function = LED_FUNCTION_DISK_ERR;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-9 {
-+			function = LED_FUNCTION_USB;
-+			function-enumerator = <1>;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-10 {
-+			function = LED_FUNCTION_USB;
-+			function-enumerator = <1>;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "usbport";
-+			trigger-sources = <&hub_port2>;
-+		};
-+
-+		led-11 {
-+			function = LED_FUNCTION_USB;
-+			function-enumerator = <2>;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		led-12 {
-+			function = LED_FUNCTION_USB;
-+			function-enumerator = <2>;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "usbport";
-+			trigger-sources = <&hub_port1>;
-+		};
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+};
-+
-+&eth0port {
-+	phy-handle = <&ethphy9>;
-+};
-+
-+&i2c0 {
-+	status = "okay";
-+
-+	rtc@30 {
-+		compatible = "s35390a";
-+		reg = <0x30>;
-+	};
-+
-+	lm63@4c {
-+		compatible = "national,lm63";
-+		reg = <0x4c>;
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy9: ethernet-phy@9 {
-+		reg = <9>;
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+	chip-delay = <40>;
-+
-+	partition@0 {
-+		label = "uboot";
-+		reg = <0x0000000 0x200000>;
-+	};
-+
-+	partition@200000 {
-+		label = "certificate";
-+		reg = <0x0200000 0x100000>;
-+	};
-+
-+	partition@300000 {
-+		label = "preset_cfg";
-+		reg = <0x0300000 0x100000>;
-+	};
-+
-+	partition@400000 {
-+		label = "dev_params";
-+		reg = <0x0400000 0x100000>;
-+	};
-+
-+	partition@500000 {
-+		label = "active_bank";
-+		reg = <0x0500000 0x0100000>;
-+	};
-+
-+	partition@600000 {
-+		label = "magic";
-+		reg = <0x0600000 0x0100000>;
-+	};
-+
-+	partition@700000 {
-+		label = "bank1";
-+		reg = <0x0700000 0x2800000>;
-+	};
-+
-+	partition@2f00000 {
-+		label = "bank2";
-+		reg = <0x2f00000 0x2800000>;
-+	};
-+
-+	/* 0x5700000-0x5a00000 undefined in vendor firmware */
-+
-+	partition@5a00000 {
-+		label = "reserved";
-+		reg = <0x5a00000 0x2000000>;
-+	};
-+
-+	partition@7a00000 {
-+		label = "rootfs";
-+		reg = <0x7a00000 0x8600000>;
-+	};
-+};
-+
-+&pinctrl {
-+	/* Buzzer gpios are connected to two pins of buzzer.
-+	 * This buzzer require a modulated signal from gpio.
-+	 * Leave it as is due lack of proper driver.
-+	 */
-+	pmx_buzzer: pmx-buzzer {
-+		marvell,pins = "mpp12", "mpp13";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_leds: pmx-leds {
-+		marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
-+			       "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
-+			       "mpp45", "mpp46", "mpp47";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_buttons: pmx-buttons {
-+		marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_poweroff: pmx-poweroff {
-+		marvell,pins = "mpp34";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&rtc {
-+	status = "disabled";
-+};
-+
-+&sata {
-+	status = "okay";
-+	nr-ports = <2>;
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
-+
-+&usb0 {
-+	#address-cells = <1>;
-+	#size-cells = <0>;
-+	status = "okay";
-+
-+	port@1 {
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		reg = <1>;
-+		#trigger-source-cells = <0>;
-+
-+		hub_port1: port@1 {
-+			reg = <1>;
-+			#trigger-source-cells = <0>;
-+		};
-+
-+		hub_port2: port@2 {
-+			reg = <2>;
-+			#trigger-source-cells = <0>;
-+		};
-+	};
-+};

target/linux/kirkwood/patches-5.15/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch

@@ -1,301 +0,0 @@
-From e977a103840c57d72b52cbc8c17f87f86ef9aa8d Mon Sep 17 00:00:00 2001
-From: Pawel Dembicki <[email protected]>
-Date: Sat, 29 Oct 2022 22:57:38 +0200
-Subject: [PATCH] ARM: dts: kirkwood: Add Zyxel NSA310S board
-
-Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
-
-Specification:
- - Processor Marvell 88F6702 1 GHz
- - 256MB RAM
- - 128MB NAND
- - 1x GBE LAN port (PHY: Marvell 88E1318)
- - 2x USB 2.0
- - 1x SATA
- - 3x button
- - 7x leds
- - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
-
-Tested-by: Tony Dinh <[email protected]>
-Signed-off-by: Pawel Dembicki <[email protected]>
-Acked-by: Adam Baker <[email protected]>
-Reviewed-by: Andrew Lunn <[email protected]>
-Signed-off-by: Gregory CLEMENT <[email protected]>
----
- arch/arm/boot/dts/Makefile             |   1 +
- arch/arm/boot/dts/kirkwood-nsa310s.dts | 259 +++++++++++++++++++++++++
- 2 files changed, 260 insertions(+)
- create mode 100644 arch/arm/boot/dts/kirkwood-nsa310s.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -320,6 +320,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-ns2mini.dtb \
- 	kirkwood-nsa310.dtb \
- 	kirkwood-nsa310a.dtb \
-+	kirkwood-nsa310s.dtb \
- 	kirkwood-nsa320.dtb \
- 	kirkwood-nsa325.dtb \
- 	kirkwood-openblocks_a6.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
-@@ -0,0 +1,259 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+/*
-+ * ZyXEL NSA310S Board Description
-+ * Copyright 2020-2022 Pawel Dembicki <[email protected]>
-+ * Copyright (c) 2015-2021, Tony Dinh <[email protected]>
-+ * Copyright (c) 2014, Adam Baker <[email protected]>
-+ * Based upon the board setup file created by Peter Schildmann
-+ */
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+#include <dt-bindings/leds/common.h>
-+
-+/ {
-+	model = "ZyXEL NSA310S";
-+	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x10000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8 earlyprintk";
-+		stdout-path = &uart0;
-+	};
-+
-+	gpio_poweroff {
-+		compatible = "gpio-poweroff";
-+		pinctrl-0 = <&pmx_pwr_off>;
-+		pinctrl-names = "default";
-+		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
-+	};
-+
-+	keys {
-+		compatible = "gpio-keys";
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+		pinctrl-0 = <&pmx_buttons>;
-+		pinctrl-names = "default";
-+
-+		power {
-+			label = "Power Button";
-+			linux,code = <KEY_POWER>;
-+			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		copy {
-+			label = "Copy Button";
-+			linux,code = <KEY_COPY>;
-+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
-+		};
-+
-+		reset {
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
-+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
-+		};
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = <&pmx_leds>;
-+		pinctrl-names = "default";
-+
-+		led-1 {
-+			function = LED_FUNCTION_DISK_ERR;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		led-2 {
-+			function = LED_FUNCTION_USB;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "usb-host";
-+		};
-+
-+		led-3 {
-+			function = LED_FUNCTION_DISK;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "ata1";
-+		};
-+
-+		led-4 {
-+			function = LED_FUNCTION_INDICATOR;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		led-5 {
-+			function = LED_FUNCTION_INDICATOR;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		led-6 {
-+			function = LED_FUNCTION_STATUS;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "default-on";
-+		};
-+
-+		led-7 {
-+			function = LED_FUNCTION_STATUS;
-+			color = <LED_COLOR_ID_RED>;
-+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+
-+	usb0_power: regulator@1 {
-+		compatible = "regulator-fixed";
-+		regulator-name = "USB Power";
-+
-+		regulator-min-microvolt = <5000000>;
-+		regulator-max-microvolt = <5000000>;
-+		regulator-always-on;
-+		regulator-boot-on;
-+		gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
-+	};
-+
-+	sata1_power: regulator@2 {
-+		compatible = "regulator-fixed";
-+		regulator-name = "SATA1 Power";
-+
-+		regulator-min-microvolt = <5000000>;
-+		regulator-max-microvolt = <5000000>;
-+		regulator-always-on;
-+		regulator-boot-on;
-+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-+	};
-+
-+	thermal-zones {
-+		disk-thermal {
-+			polling-delay = <20000>;
-+			polling-delay-passive = <2000>;
-+
-+			thermal-sensors = <&hdd_temp>;
-+
-+			trips {
-+				disk_alert: disk-alert {
-+					temperature = <40000>;
-+					hysteresis = <5000>;
-+					type = "active";
-+				};
-+				disk_crit: disk-crit {
-+					temperature = <60000>;
-+					hysteresis = <2000>;
-+					type = "critical";
-+				};
-+			};
-+		};
-+	};
-+};
-+
-+
-+&eth0 {
-+	status = "okay";
-+
-+	ethernet0-port@0 {
-+		phy-handle = <&ethphy0>;
-+	};
-+};
-+
-+&i2c0 {
-+	status = "okay";
-+
-+	rtc@68 {
-+		compatible = "htk,ht1382";
-+		reg = <0x68>;
-+	};
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphy0: ethernet-phy@1 {
-+		reg = <1>;
-+		phy-mode = "rgmii-id";
-+		marvell,reg-init = <0x1 0x16 0x0 0x3>,
-+				   <0x1 0x10 0x0 0x1017>,
-+				   <0x1 0x11 0x0 0x4408>,
-+				   <0x1 0x16 0x0 0x0>;
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+	chip-delay = <35>;
-+
-+	partition@0 {
-+		label = "uboot";
-+		reg = <0x0000000 0x00c0000>;
-+		read-only;
-+	};
-+	partition@c0000 {
-+		label = "uboot_env";
-+		reg = <0x00c0000 0x0080000>;
-+	};
-+	partition@140000 {
-+		label = "ubi";
-+		reg = <0x0140000 0x7ec0000>;
-+	};
-+};
-+
-+&pciec {
-+	status = "okay";
-+};
-+
-+&pcie0 {
-+	status = "okay";
-+};
-+
-+&pinctrl {
-+	pinctrl-names = "default";
-+
-+	pmx_buttons: pmx-buttons {
-+		marvell,pins = "mpp24", "mpp25", "mpp26";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_leds: pmx-leds {
-+		marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23",
-+						"mpp28", "mpp29";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_power: pmx-power {
-+		marvell,pins = "mpp21", "mpp33";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_pwr_off: pmx-pwr-off {
-+		marvell,pins = "mpp27";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&rtc {
-+	status = "disabled";
-+};
-+
-+&sata {
-+	status = "okay";
-+	nr-ports = <1>;
-+	#address-cells = <1>;
-+	#size-cells = <0>;
-+
-+	hdd_temp: sata-port@0 {
-+		reg = <0>;
-+		#thermal-sensor-cells = <0>;
-+	};
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};

target/linux/kirkwood/patches-5.15/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch

@@ -1,249 +0,0 @@
-From 5668d088ee4ea05db9daaae0645d1d1f579b20f9 Mon Sep 17 00:00:00 2001
-From: Pawel Dembicki <[email protected]>
-Date: Mon, 3 Oct 2022 09:34:43 +0200
-Subject: ARM: dts: kirkwood: Add Endian 4i Edge 200 board
-
-Add Endian 4i Edge 200 is 5-port firewall.
-It have also clone: Endian UTM Mini (The same hardware, with added WLAN
-card).
-
-Hardware:
-  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
-  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
-  - NAND Flash: 512MB (Micron 29F4G08AAC)
-  - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
-  - Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
-  - Storage: MicroSD Slot
-  - MCPIE: MiniPCIe Slot present [fitted with SparkLan WPEA-110N/E
-          (Atheros AR9280 chipset) in Endian UTM Mini WLAN only]
-  - USB: 1x USB 2.0 port
-  - Console: RJ-45 port
-  - LEDs: 3x GPIO controlled
-
-Signed-off-by: Pawel Dembicki <[email protected]>
-Reviewed-by: Andrew Lunn <[email protected]>
-Signed-off-by: Gregory CLEMENT <[email protected]>
----
- arch/arm/boot/dts/Makefile                 |   1 +
- arch/arm/boot/dts/kirkwood-4i-edge-200.dts | 205 +++++++++++++++++++++++++++++
- 2 files changed, 206 insertions(+)
- create mode 100644 arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -265,6 +265,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
- 	keystone-k2g-evm.dtb \
- 	keystone-k2g-ice.dtb
- dtb-$(CONFIG_MACH_KIRKWOOD) += \
-+	kirkwood-4i-edge-200.dtb \
- 	kirkwood-b3.dtb \
- 	kirkwood-blackarmor-nas220.dtb \
- 	kirkwood-c200-v1.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-@@ -0,0 +1,205 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+/*
-+ * Endian 4i Edge 200 Board Description
-+ * Note: Endian UTM Mini is hardware clone of Endian Edge 200
-+ * Copyright 2021-2022 Pawel Dembicki <[email protected]>
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+#include <dt-bindings/leds/common.h>
-+
-+/ {
-+	model = "Endian 4i Edge 200";
-+	compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x20000000>;
-+	};
-+
-+	chosen {
-+		bootargs = "console=ttyS0,115200n8";
-+		stdout-path = &uart0;
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+		pinctrl-0 = <&pmx_led>;
-+		pinctrl-names = "default";
-+
-+		led-1 {
-+			function = LED_FUNCTION_SD;
-+			color = <LED_COLOR_ID_AMBER>;
-+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "mmc0";
-+		};
-+
-+		led-2 {
-+			function = LED_FUNCTION_STATUS;
-+			color = <LED_COLOR_ID_AMBER>;
-+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		led-3 {
-+			function = LED_FUNCTION_STATUS;
-+			color = <LED_COLOR_ID_GREEN>;
-+			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
-+		};
-+	};
-+};
-+
-+&eth0 {
-+	status = "okay";
-+};
-+
-+&eth0port {
-+	speed = <1000>;
-+	duplex = <1>;
-+};
-+
-+&eth1 {
-+	status = "okay";
-+};
-+
-+&eth1port {
-+	phy-handle = <&ethphyb>;
-+};
-+
-+&mdio {
-+	status = "okay";
-+
-+	ethphyb: ethernet-phy@b {
-+		reg = <0x0b>;
-+
-+		marvell,reg-init =
-+			/* link-activity, bi-color mode 4 */
-+			<3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */
-+	};
-+
-+	switch0: switch@11 {
-+		compatible = "marvell,mv88e6085";
-+		reg = <0x11>;
-+
-+		ports {
-+			#address-cells = <1>;
-+			#size-cells = <0>;
-+
-+			port@0 {
-+				reg = <0>;
-+				label = "port1";
-+			};
-+
-+			port@1 {
-+				reg = <1>;
-+				label = "port2";
-+			};
-+
-+			port@2 {
-+				reg = <2>;
-+				label = "port3";
-+			};
-+
-+			port@3 {
-+				reg = <3>;
-+				label = "port4";
-+			};
-+
-+			port@5 {
-+				reg = <5>;
-+				phy-mode = "rgmii-id";
-+				ethernet = <&eth0port>;
-+
-+				fixed-link {
-+					speed = <1000>;
-+					full-duplex;
-+				};
-+			};
-+		};
-+	};
-+};
-+
-+&nand {
-+	status = "okay";
-+	pinctrl-0 = <&pmx_nand>;
-+	pinctrl-names = "default";
-+
-+	partition@0 {
-+		label = "u-boot";
-+		reg = <0x00000000 0x000a0000>;
-+		read-only;
-+	};
-+
-+	partition@a0000 {
-+		label = "u-boot-env";
-+		reg = <0x000a0000 0x00060000>;
-+		read-only;
-+	};
-+
-+	partition@100000 {
-+		label = "kernel";
-+		reg = <0x00100000 0x00400000>;
-+	};
-+
-+	partition@500000 {
-+		label = "ubi";
-+		reg = <0x00500000 0x1fb00000>;
-+	};
-+};
-+
-+&pciec {
-+	status = "okay";
-+};
-+
-+&pcie0 {
-+	status = "okay";
-+};
-+
-+&pinctrl {
-+	pinctrl-0 = <&pmx_sysrst>;
-+	pinctrl-names = "default";
-+
-+	pmx_sysrst: pmx-sysrst {
-+		marvell,pins = "mpp6";
-+		marvell,function = "sysrst";
-+	};
-+
-+	pmx_sdio_cd: pmx-sdio-cd {
-+		marvell,pins = "mpp28";
-+		marvell,function = "gpio";
-+	};
-+
-+	pmx_led: pmx-led {
-+		marvell,pins = "mpp34", "mpp35", "mpp49";
-+		marvell,function = "gpio";
-+	};
-+};
-+
-+&rtc {
-+	status = "okay";
-+};
-+
-+&sata_phy0 {
-+	status = "disabled";
-+};
-+
-+&sata_phy1 {
-+	status = "disabled";
-+};
-+
-+&sdio {
-+	pinctrl-0 = <&pmx_sdio_cd>;
-+	pinctrl-names = "default";
-+	status = "okay";
-+	cd-gpios = <&gpio0 28 9>;
-+};
-+
-+&uart0 {
-+	status = "okay";
-+};
-+
-+&usb0 {
-+	status = "okay";
-+};

target/linux/kirkwood/patches-5.15/100-ib62x0.patch

@@ -1,53 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
-+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
-@@ -6,7 +6,14 @@
- 
- / {
- 	model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
--	compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+	compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+	aliases {
-+		led-boot = &led_green_os;
-+		led-failsafe = &led_red_os;
-+		led-running = &led_green_os;
-+		led-upgrade = &led_red_os;
-+	};
- 
- 	memory {
- 		device_type = "memory";
-@@ -81,12 +88,12 @@
- 			     &pmx_led_usb_transfer>;
- 		pinctrl-names = "default";
- 
--		green-os {
-+		led_green_os: green-os {
- 			label = "ib62x0:green:os";
- 			gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
--		red-os {
-+		led_red_os: red-os {
- 			label = "ib62x0:red:os";
- 			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
- 		};
-@@ -118,13 +125,13 @@
- 	};
- 
- 	partition@100000 {
--		label = "uImage";
--		reg = <0x0100000 0x600000>;
-+		label = "second stage u-boot";
-+		reg = <0x100000 0x200000>;
- 	};
- 
--	partition@700000 {
--		label = "root";
--		reg = <0x0700000 0xf900000>;
-+	partition@200000 {
-+		label = "ubi";
-+		reg = <0x200000 0xfe00000>;
- 	};
- 
- };

target/linux/kirkwood/patches-5.15/101-iconnect.patch

@@ -1,80 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-iconnect.dts
-+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
-@@ -8,6 +8,13 @@
- 	model = "Iomega Iconnect";
- 	compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_power_blue;
-+		led-failsafe = &led_power_red;
-+		led-running = &led_power_blue;
-+		led-upgrade = &led_power_red;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x10000000>;
-@@ -16,8 +23,6 @@
- 	chosen {
- 		bootargs = "console=ttyS0,115200n8 earlyprintk";
- 		stdout-path = &uart0;
--		linux,initrd-start = <0x4500040>;
--		linux,initrd-end   = <0x4800000>;
- 	};
- 
- 	ocp@f1000000 {
-@@ -89,12 +94,12 @@
- 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- 			default-state = "on";
- 		};
--		power-blue {
-+		led_power_blue: power-blue {
- 			label = "power:blue";
- 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
--		power-red {
-+		led_power_red: power-red {
- 			label = "power:red";
- 			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
- 		};
-@@ -146,28 +151,23 @@
- 	status = "okay";
- 
- 	partition@0 {
--		label = "uboot";
--		reg = <0x0000000 0xc0000>;
-+		label = "u-boot";
-+		reg = <0x0000000 0xe0000>;
- 	};
- 
--	partition@a0000 {
--		label = "env";
--		reg = <0xa0000 0x20000>;
-+	partition@e0000 {
-+		label = "u-boot environment";
-+		reg = <0xe0000 0x100000>;
- 	};
- 
- 	partition@100000 {
--		label = "zImage";
--		reg = <0x100000 0x300000>;
--	};
--
--	partition@540000 {
--		label = "initrd";
--		reg = <0x540000 0x300000>;
-+		label = "second stage u-boot";
-+		reg = <0x100000 0x200000>;
- 	};
- 
--	partition@980000 {
--		label = "boot";
--		reg = <0x980000 0x1f400000>;
-+	partition@200000 {
-+		label = "ubi";
-+		reg = <0x200000 0x1fe00000>;
- 	};
- };
- 

target/linux/kirkwood/patches-5.15/102-dockstar.patch

@@ -1,62 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-dockstar.dts
-+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
-@@ -8,6 +8,13 @@
- 	model = "Seagate FreeAgent Dockstar";
- 	compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_fault;
-+		led-running = &led_health;
-+		led-upgrade = &led_fault;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x8000000>;
-@@ -42,12 +49,12 @@
- 		pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
- 		pinctrl-names = "default";
- 
--		health {
-+		led_health: health {
- 			label = "status:green:health";
- 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
--		fault {
-+		led_fault: fault {
- 			label = "status:orange:fault";
- 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- 		};
-@@ -78,18 +85,22 @@
- 
- 	partition@0 {
- 		label = "u-boot";
--		reg = <0x0000000 0x100000>;
--		read-only;
-+		reg = <0x0000000 0xe0000>;
-+	};
-+
-+	partition@e0000 {
-+		label = "u-boot environment";
-+		reg = <0xe0000 0x100000>;
- 	};
- 
- 	partition@100000 {
--		label = "uImage";
--		reg = <0x0100000 0x400000>;
-+		label = "second stage u-boot";
-+		reg = <0x100000 0x200000>;
- 	};
- 
--	partition@500000 {
--		label = "data";
--		reg = <0x0500000 0xfb00000>;
-+	partition@200000 {
-+		label = "ubi";
-+		reg = <0x200000 0xfe00000>;
- 	};
- };
- 

target/linux/kirkwood/patches-5.15/103-iomega-ix2-200.patch

@@ -1,67 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
-+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
-@@ -8,6 +8,13 @@
- 	model = "Iomega StorCenter ix2-200";
- 	compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_power;
-+		led-failsafe = &led_health;
-+		led-running = &led_power;
-+		led-upgrade = &led_health;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x10000000>;
-@@ -127,16 +134,16 @@
- 			      &pmx_led_rebuild &pmx_led_health >;
- 		pinctrl-names = "default";
- 
--		power_led {
-+		led_power: power_led {
- 			label = "status:white:power_led";
- 			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
- 		rebuild_led {
- 			label = "status:white:rebuild_led";
- 			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
- 		};
--		health_led {
-+		led_health: health_led {
- 			label = "status:red:health_led";
- 			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
- 		};
-@@ -186,18 +193,18 @@
- 	};
- 
- 	partition@a0000 {
--		label = "env";
-+		label = "u-boot environment";
- 		reg = <0xa0000 0x20000>;
- 		read-only;
- 	};
- 
- 	partition@100000 {
--		label = "uImage";
-+		label = "kernel";
- 		reg = <0x100000 0x300000>;
- 	};
- 
- 	partition@400000 {
--		label = "rootfs";
-+		label = "ubi";
- 		reg = <0x400000 0x1C00000>;
- 	};
- };
-@@ -211,7 +218,7 @@
- };
- 
- &eth0 {
--	status = "okay";
-+	status = "disabled";
- 	ethernet0-port@0 {
- 		speed = <1000>;
- 		duplex = <1>;

target/linux/kirkwood/patches-5.15/105-linksys-viper-dts.patch

@@ -1,59 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-@@ -24,6 +24,10 @@
- 	};
- 
- 	aliases {
-+		led-boot = &led_white_health;
-+		led-failsafe = &led_white_health;
-+		led-running = &led_white_health;
-+		led-upgrade = &led_white_health;
- 		serial0 = &uart0;
- 	};
- 
-@@ -56,9 +60,10 @@
- 		pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
- 		pinctrl-names = "default";
- 
--		white-health {
-+		led_white_health: white-health {
- 			label = "viper:white:health";
- 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
- 		};
- 
- 		white-pulse {
-@@ -114,23 +119,23 @@
- 		};
- 
- 		partition@200000 {
--			label = "kernel";
--			reg = <0x200000 0x2A0000>;
-+			label = "kernel1";
-+			reg = <0x200000 0x1A00000>;
- 		};
- 
--		partition@4a0000 {
--			label = "rootfs";
--			reg = <0x4A0000 0x1760000>;
-+		partition@500000 {
-+			label = "rootfs1";
-+			reg = <0x500000 0x1700000>;
- 		};
- 
- 		partition@1c00000 {
--			label = "alt_kernel";
--			reg = <0x1C00000 0x2A0000>;
-+			label = "kernel2";
-+			reg = <0x1C00000 0x1A00000>;
- 		};
- 
--		partition@1ea0000 {
--			label = "alt_rootfs";
--			reg = <0x1EA0000 0x1760000>;
-+		partition@1f00000 {
-+			label = "rootfs2";
-+			reg = <0x1F00000 0x1700000>;
- 		};
- 
- 		partition@3600000 {

target/linux/kirkwood/patches-5.15/106-goflexnet.patch

@@ -1,53 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
-+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
-@@ -8,6 +8,13 @@
- 	model = "Seagate GoFlex Net";
- 	compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_fault;
-+		led-running = &led_health;
-+		led-upgrade = &led_fault;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x8000000>;
-@@ -85,12 +92,12 @@
- 			    >;
- 		pinctrl-names = "default";
- 
--		health {
-+		led_health: health {
- 			label = "status:green:health";
- 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
--		fault {
-+		led_fault: fault {
- 			label = "status:orange:fault";
- 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- 		};
-@@ -159,18 +166,8 @@
- 	};
- 
- 	partition@100000 {
--		label = "uImage";
--		reg = <0x0100000 0x400000>;
--	};
--
--	partition@500000 {
--		label = "pogoplug";
--		reg = <0x0500000 0x2000000>;
--	};
--
--	partition@2500000 {
--		label = "root";
--		reg = <0x02500000 0xd800000>;
-+		label = "ubi";
-+		reg = <0x0100000 0x0ff00000>;
- 	};
- };
- 

target/linux/kirkwood/patches-5.15/107-01-zyxel-nsa3x0-common-nand-partitions.patch

@@ -1,48 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
-+++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
-@@ -112,40 +112,16 @@
- 
- 	partition@0 {
- 		label = "uboot";
--		reg = <0x0000000 0x0100000>;
-+		reg = <0x0000000 0x00c0000>;
- 		read-only;
- 	};
- 	partition@100000 {
- 		label = "uboot_env";
--		reg = <0x0100000 0x0080000>;
-+		reg = <0x00c0000 0x0080000>;
- 	};
--	partition@180000 {
--		label = "key_store";
--		reg = <0x0180000 0x0080000>;
--	};
--	partition@200000 {
--		label = "info";
--		reg = <0x0200000 0x0080000>;
--	};
--	partition@280000 {
--		label = "etc";
--		reg = <0x0280000 0x0a00000>;
--	};
--	partition@c80000 {
--		label = "kernel_1";
--		reg = <0x0c80000 0x0a00000>;
--	};
--	partition@1680000 {
--		label = "rootfs1";
--		reg = <0x1680000 0x2fc0000>;
--	};
--	partition@4640000 {
--		label = "kernel_2";
--		reg = <0x4640000 0x0a00000>;
--	};
--	partition@5040000 {
--		label = "rootfs2";
--		reg = <0x5040000 0x2fc0000>;
-+	partition@140000 {
-+		label = "ubi";
-+		reg = <0x0140000 0x7ec0000>;
- 	};
- };
- 

target/linux/kirkwood/patches-5.15/107-03-nsa325.patch

@@ -1,54 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-nsa325.dts
-+++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
-@@ -15,6 +15,13 @@
- 	model = "ZyXEL NSA325";
- 	compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_green_sys;
-+		led-failsafe = &led_orange_sys;
-+		led-running = &led_green_sys;
-+		led-upgrade = &led_orange_sys;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x20000000>;
-@@ -162,17 +169,19 @@
- 			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
- 		pinctrl-names = "default";
- 
--		green-sys {
-+		led_green_sys: green-sys {
- 			label = "nsa325:green:sys";
- 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+			default-state = "on";
- 		};
--		orange-sys {
-+		led_orange_sys: orange-sys {
- 			label = "nsa325:orange:sys";
- 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
- 		};
- 		green-hdd1 {
- 			label = "nsa325:green:hdd1";
- 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "ata1";
- 		};
- 		red-hdd1 {
- 			label = "nsa325:red:hdd1";
-@@ -181,6 +190,7 @@
- 		green-hdd2 {
- 			label = "nsa325:green:hdd2";
- 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "ata2";
- 		};
- 		red-hdd2 {
- 			label = "nsa325:red:hdd2";
-@@ -189,6 +199,7 @@
- 		green-usb {
- 			label = "nsa325:green:usb";
- 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+			linux,default-trigger = "usb-host";
- 		};
- 		green-copy {
- 			label = "nsa325:green:copy";

target/linux/kirkwood/patches-5.15/109-pogoplug_v4.patch

@@ -1,87 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
-+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
-@@ -18,12 +18,20 @@
- 	compatible = "cloudengines,pogoplugv4", "marvell,kirkwood-88f6192",
- 		     "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_fault;
-+		led-running = &led_health;
-+		led-upgrade = &led_fault;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x08000000>;
- 	};
- 
- 	chosen {
-+		bootargs = "console=ttyS0,115200";
- 		stdout-path = "uart0:115200n8";
- 	};
- 
-@@ -37,8 +45,8 @@
- 		eject {
- 			debounce-interval = <50>;
- 			wakeup-source;
--			linux,code = <KEY_EJECTCD>;
--			label = "Eject Button";
-+			linux,code = <KEY_RESTART>;
-+			label = "Reset";
- 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
- 		};
- 	};
-@@ -48,12 +56,12 @@
- 		pinctrl-0 = <&pmx_led_green &pmx_led_red>;
- 		pinctrl-names = "default";
- 
--		health {
-+		led_health: health {
- 			label = "pogoplugv4:green:health";
- 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
- 			default-state = "on";
- 		};
--		fault {
-+		led_fault: fault {
- 			label = "pogoplugv4:red:fault";
- 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
- 		};
-@@ -137,29 +145,19 @@
- 		#size-cells = <1>;
- 
- 		partition@0 {
--			label = "u-boot";
--			reg = <0x00000000 0x200000>;
-+			label = "uboot";
-+			reg = <0x00000000 0x1c0000>;
- 			read-only;
- 		};
- 
--		partition@200000 {
--			label = "uImage";
--			reg = <0x00200000 0x300000>;
--		};
--
--		partition@500000 {
--			label = "uImage2";
--			reg = <0x00500000 0x300000>;
--		};
--
--		partition@800000 {
--			label = "failsafe";
--			reg = <0x00800000 0x800000>;
-+		partition@1c0000 {
-+			label = "uboot_env";
-+			reg = <0x001c0000 0x40000>;
- 		};
- 
--		partition@1000000 {
--			label = "root";
--			reg = <0x01000000 0x7000000>;
-+		partition@200000 {
-+			label = "ubi";
-+			reg = <0x00200000 0x7e00000>;
- 		};
- 	};
- };

target/linux/kirkwood/patches-5.15/110-pogo_e02.patch

@@ -1,68 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
-+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
-@@ -20,6 +20,13 @@
- 	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
- 		     "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_fault;
-+		led-running = &led_health;
-+		led-upgrade = &led_fault;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x10000000>;
-@@ -33,12 +40,12 @@
- 	gpio-leds {
- 		compatible = "gpio-leds";
- 
--		health {
-+		led_health: health {
- 			label = "pogo_e02:green:health";
- 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
--		fault {
-+		led_fault: fault {
- 			label = "pogo_e02:orange:fault";
- 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
- 		};
-@@ -95,24 +102,24 @@
- 	status = "okay";
- 
- 	partition@0 {
--		label = "u-boot";
--		reg = <0x0000000 0x100000>;
-+		label = "uboot";
-+		reg = <0x0 0xe0000>;
- 		read-only;
- 	};
- 
--	partition@100000 {
--		label = "uImage";
--		reg = <0x0100000 0x400000>;
-+	partition@e0000 {
-+		label = "uboot_env";
-+		reg = <0xe0000 0x20000>;
- 	};
- 
--	partition@500000 {
--		label = "pogoplug";
--		reg = <0x0500000 0x2000000>;
-+	partition@100000 {
-+		label = "second_stage_uboot";
-+		reg = <0x100000 0x100000>;
- 	};
- 
--	partition@2500000 {
--		label = "root";
--		reg = <0x02500000 0x5b00000>;
-+	partition@200000 {
-+		label = "ubi";
-+		reg = <0x200000 0x7e00000>;
- 	};
- };
- 

target/linux/kirkwood/patches-5.15/111-l-50.patch

@@ -1,47 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-l-50.dts
-+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
-@@ -18,6 +18,13 @@
- 		reg = <0x00000000 0x20000000>;
- 	};
- 
-+	aliases {
-+		led-boot = &led_status_green;
-+		led-failsafe = &led_status_red;
-+		led-running = &led_status_green;
-+		led-upgrade = &led_status_red;
-+	};
-+
- 	chosen {
- 		bootargs = "console=ttyS0,115200n8";
- 		stdout-path = &uart0;
-@@ -95,12 +102,12 @@
- 	leds {
- 		compatible = "gpio-leds";
- 
--		status_green {
-+		led_status_green: status_green {
- 			label = "l-50:green:status";
- 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
- 		};
- 
--		status_red {
-+		led_status_red: status_red {
- 			label = "l-50:red:status";
- 			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
- 		};
-@@ -349,13 +356,8 @@
- 	};
- 
- 	partition@100000 {
--		label = "kernel-1";
--		reg = <0x00100000 0x00800000>;
--	};
--
--	partition@900000 {
--		label = "rootfs-1";
--		reg = <0x00900000 0x07100000>;
-+		label = "ubi";
-+		reg = <0x00100000 0x07900000>;
- 	};
- 
- 	partition@7a00000 {

target/linux/kirkwood/patches-5.15/112-sheevaplug.patch

@@ -1,47 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
-+++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
-@@ -78,13 +78,8 @@
- 	};
- 
- 	partition@100000 {
--		label = "uImage";
--		reg = <0x0100000 0x400000>;
--	};
--
--	partition@500000 {
--		label = "root";
--		reg = <0x0500000 0x1fb00000>;
-+		label = "ubi";
-+		reg = <0x0100000 0x1ff00000>;
- 	};
- };
- 
---- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts
-+++ b/arch/arm/boot/dts/kirkwood-sheevaplug.dts
-@@ -13,6 +13,13 @@
- 	model = "Globalscale Technologies SheevaPlug";
- 	compatible = "globalscale,sheevaplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_health;
-+		led-failsafe = &led_health;
-+		led-running = &led_health;
-+		led-upgrade = &led_health;
-+	};
-+
- 	ocp@f1000000 {
- 		mvsdio@90000 {
- 			pinctrl-0 = <&pmx_sdio>;
-@@ -28,10 +35,10 @@
- 		pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
- 		pinctrl-names = "default";
- 
--		health {
-+		led_health: health {
- 			label = "sheevaplug:blue:health";
- 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
--			default-state = "keep";
-+			default-state = "on";
- 		};
- 
- 		misc {

target/linux/kirkwood/patches-5.15/113-readynas_duo_v2.patch

@@ -1,76 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
-+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
-@@ -19,6 +19,13 @@
- 		reg = <0x00000000 0x10000000>;
- 	};
- 
-+	aliases {
-+		led-boot = &led_power;
-+		led-failsafe = &led_power;
-+		led-running = &led_power;
-+		led-upgrade = &led_power;
-+	};
-+
- 	chosen {
- 		bootargs = "console=ttyS0,115200n8 earlyprintk";
- 		stdout-path = &uart0;
-@@ -115,7 +122,7 @@
- 			      &pmx_led_blue_backup >;
- 		pinctrl-names = "default";
- 
--		power_led {
-+		led_power: power_led {
- 			label = "status:blue:power_led";
- 			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
- 			default-state = "keep";
-@@ -129,11 +136,13 @@
- 		disk1_led {
- 			label = "status:blue:disk1_led";
- 			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "ata1";
- 		};
- 
- 		disk2_led {
- 			label = "status:blue:disk2_led";
- 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "ata2";
- 		};
- 
- 		backup_led {
-@@ -150,7 +159,13 @@
- 
- 		power-button {
- 			label = "Power Button";
--			linux,code = <KEY_POWER>;
-+			/* Power button and INT pin from PHY are both connected
-+			 * to this GPIO. Every network restart causes PHY restart
-+			 * and button is pressed. It's difficult to use it as
-+			 * KEY_POWER without changes in kernel (or netifd) so
-+			 * the button is configured as regular one.
-+			 */
-+			linux,code = <BTN_1>;
- 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- 		};
- 
-@@ -208,18 +223,13 @@
- 	};
- 
- 	partition@200000 {
--		label = "uImage";
-+		label = "kernel";
- 		reg = <0x0200000 0x600000>;
- 	};
- 
- 	partition@800000 {
--		label = "minirootfs";
--		reg = <0x0800000 0x1000000>;
--	};
--
--	partition@1800000 {
--		label = "jffs2";
--		reg = <0x1800000 0x6800000>;
-+		label = "ubi";
-+		reg = <0x0800000 0x7800000>;
- 	};
- };
- 

target/linux/kirkwood/patches-5.15/114-ctera-c-200-v1.patch

@@ -1,60 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-c200-v1.dts
-+++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
-@@ -14,6 +14,14 @@
- 	model = "Ctera C200 V1";
- 	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
- 
-+
-+	aliases {
-+		led-boot = &led_status_green;
-+		led-failsafe = &led_status_red;
-+		led-running = &led_status_green;
-+		led-upgrade = &led_status_red;
-+	};
-+
- 	chosen {
- 		bootargs = "console=ttyS0,115200";
- 		stdout-path = &uart0;
-@@ -78,6 +86,7 @@
- 			function-enumerator = <1>;
- 			color = <LED_COLOR_ID_GREEN>;
- 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "ata1";
- 		};
- 
- 		led-2 {
-@@ -85,6 +94,7 @@
- 			function-enumerator = <2>;
- 			color = <LED_COLOR_ID_GREEN>;
- 			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "ata2";
- 		};
- 
- 		led-3 {
-@@ -94,13 +104,15 @@
- 			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
- 		};
- 
--		led-4 {
-+		led_status_red: led-4 {
-+			label = "red:status";
- 			function = LED_FUNCTION_STATUS;
- 			color = <LED_COLOR_ID_RED>;
- 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
- 		};
- 
--		led-5 {
-+		led_status_green: led-5 {
-+			label = "green:status";
- 			function = LED_FUNCTION_STATUS;
- 			color = <LED_COLOR_ID_GREEN>;
- 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
-@@ -240,7 +252,7 @@
- 	};
- 
- 	partition@7a00000 {
--		label = "rootfs";
-+		label = "ubi";
- 		reg = <0x7a00000 0x8600000>;
- 	};
- };

target/linux/kirkwood/patches-5.15/115-nsa310s.patch

@@ -1,35 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-nsa310s.dts
-+++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
-@@ -16,6 +16,13 @@
- 	model = "ZyXEL NSA310S";
- 	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_green_sys;
-+		led-failsafe = &led_red_sys;
-+		led-running = &led_green_sys;
-+		led-upgrade = &led_red_sys;
-+	};
-+
- 	memory {
- 		device_type = "memory";
- 		reg = <0x00000000 0x10000000>;
-@@ -96,14 +103,16 @@
- 			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
- 		};
- 
--		led-6 {
-+		led_green_sys: led-6 {
-+			label = "nsa310s:green:sys";
- 			function = LED_FUNCTION_STATUS;
- 			color = <LED_COLOR_ID_GREEN>;
- 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
- 			linux,default-trigger = "default-on";
- 		};
- 
--		led-7 {
-+		led_red_sys: led-7 {
-+			label = "nsa310s:red:sys";
- 			function = LED_FUNCTION_STATUS;
- 			color = <LED_COLOR_ID_RED>;
- 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;

target/linux/kirkwood/patches-5.15/116-4i-edge-200.patch

@@ -1,34 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-+++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
-@@ -20,6 +20,13 @@
- 		reg = <0x00000000 0x20000000>;
- 	};
- 
-+	aliases {
-+		led-boot = &led_status_green;
-+		led-failsafe = &led_status_orange;
-+		led-running = &led_status_green;
-+		led-upgrade = &led_status_orange;
-+	};
-+
- 	chosen {
- 		bootargs = "console=ttyS0,115200n8";
- 		stdout-path = &uart0;
-@@ -37,13 +44,15 @@
- 			linux,default-trigger = "mmc0";
- 		};
- 
--		led-2 {
-+		led_status_orange: led-2 {
-+			label = "orange:status";
- 			function = LED_FUNCTION_STATUS;
- 			color = <LED_COLOR_ID_AMBER>;
- 			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
- 		};
- 
--		led-3 {
-+		led_status_green: led-3 {
-+			label = "green:status";
- 			function = LED_FUNCTION_STATUS;
- 			color = <LED_COLOR_ID_GREEN>;
- 			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;

target/linux/kirkwood/patches-5.15/117-netgear_stora.patch

@@ -1,10 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -339,6 +339,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- 	kirkwood-rs411.dtb \
- 	kirkwood-sheevaplug.dtb \
- 	kirkwood-sheevaplug-esata.dtb \
-+	kirkwood-stora.dtb \
- 	kirkwood-t5325.dtb \
- 	kirkwood-topkick.dtb \
- 	kirkwood-ts219-6281.dtb \

target/linux/kirkwood/patches-5.15/201-enable-sata-port-specific-led-triggers.patch

@@ -1,10 +0,0 @@
---- a/arch/arm/mach-mvebu/Kconfig
-+++ b/arch/arm/mach-mvebu/Kconfig
-@@ -116,6 +116,7 @@ config MACH_DOVE
- config MACH_KIRKWOOD
- 	bool "Marvell Kirkwood boards"
- 	depends on ARCH_MULTI_V5
-+	select ARCH_WANT_LIBATA_LEDS
- 	select CPU_FEROCEON
- 	select GPIOLIB
- 	select KIRKWOOD_CLK

target/linux/kirkwood/patches-5.15/202-linksys-find-active-root.patch

@@ -1,62 +0,0 @@
-The WRT1900AC among other Linksys routers uses a dual-firmware layout.
-Dynamically rename the active partition to "ubi".
-
-Signed-off-by: Imre Kaloz <[email protected]>
----
---- a/drivers/mtd/parsers/ofpart_core.c
-+++ b/drivers/mtd/parsers/ofpart_core.c
-@@ -38,6 +38,8 @@ static bool node_has_compatible(struct d
- 	return of_get_property(pp, "compatible", NULL);
- }
- 
-+static int mangled_rootblock;
-+
- static int parse_fixed_partitions(struct mtd_info *master,
- 				  const struct mtd_partition **pparts,
- 				  struct mtd_part_parser_data *data)
-@@ -47,6 +49,7 @@ static int parse_fixed_partitions(struct
- 	struct mtd_partition *parts;
- 	struct device_node *mtd_node;
- 	struct device_node *ofpart_node;
-+	const char *owrtpart = "ubi";
- 	const char *partname;
- 	struct device_node *pp;
- 	int nr_parts, i, ret = 0;
-@@ -133,9 +136,15 @@ static int parse_fixed_partitions(struct
- 		parts[i].size = of_read_number(reg + a_cells, s_cells);
- 		parts[i].of_node = pp;
- 
--		partname = of_get_property(pp, "label", &len);
--		if (!partname)
--			partname = of_get_property(pp, "name", &len);
-+		if (mangled_rootblock && (i == mangled_rootblock)) {
-+			partname = owrtpart;
-+		} else {
-+			partname = of_get_property(pp, "label", &len);
-+
-+			if (!partname)
-+				partname = of_get_property(pp, "name", &len);
-+		}
-+
- 		parts[i].name = partname;
- 
- 		if (of_get_property(pp, "read-only", &len))
-@@ -252,6 +261,18 @@ static int __init ofpart_parser_init(voi
- 	return 0;
- }
- 
-+static int __init active_root(char *str)
-+{
-+	get_option(&str, &mangled_rootblock);
-+
-+	if (!mangled_rootblock)
-+		return 1;
-+
-+	return 1;
-+}
-+
-+__setup("mangled_rootblock=", active_root);
-+
- static void __exit ofpart_parser_exit(void)
- {
- 	deregister_mtd_parser(&ofpart_parser);

target/linux/kirkwood/patches-5.15/203-blackarmor-nas220.patch

@@ -1,99 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
-+++ b/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
-@@ -17,6 +17,13 @@
- 	compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
- 		     "marvell,kirkwood";
- 
-+	aliases {
-+		led-boot = &led_status_amber;
-+		led-failsafe = &led_status_amber;
-+		led-running = &led_status_blue;
-+		led-upgrade = &led_status_amber;
-+	};
-+
- 	memory { /* 128 MB */
- 		device_type = "memory";
- 		reg = <0x00000000 0x8000000>;
-@@ -36,14 +43,14 @@
- 		compatible = "gpio-keys";
- 
- 		reset {
--			label = "Reset";
--			linux,code = <KEY_POWER>;
-+			label = "Reset Button";
-+			linux,code = <KEY_RESTART>;
- 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
- 		};
- 
--		button {
--			label = "Power";
--			linux,code = <KEY_SLEEP>;
-+		power {
-+			label = "Power Button";
-+			linux,code = <KEY_POWER>;
- 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
- 		};
- 	};
-@@ -51,11 +58,27 @@
- 	gpio-leds {
- 		compatible = "gpio-leds";
- 
--		blue-power {
-+		led_power_blue: power_blue {
- 			label = "nas220:blue:power";
- 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
- 			linux,default-trigger = "default-on";
- 		};
-+
-+		disk_blue {
-+			label = "nas220:blue:disk";
-+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
-+			linux,default-trigger = "disk-activity";
-+		};
-+
-+		led_status_blue: status_blue {
-+			label = "nas220:blue:status";
-+			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-+		};
-+
-+		led_status_amber: status_amber {
-+			label = "nas220:amber:status";
-+			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
-+		};
- 	};
- 
- 	regulators {
-@@ -153,6 +176,33 @@
- 
- &nand {
- 	status = "okay";
-+
-+	partitions {
-+		compatible = "fixed-partitions";
-+
-+		partition@0 {
-+			label = "uboot";
-+			reg = <0x0 0xa0000>;
-+			read-only;
-+		};
-+
-+		partition@a0000 {
-+			label = "uboot-env";
-+			reg = <0xa0000 0x10000>;
-+			read-only;
-+		};
-+
-+		partition@b0000 {
-+			label = "reserved";
-+			reg = <0xb0000 0x10000>;
-+			read-only;
-+		};
-+
-+		partition@c0000 {
-+			label = "ubi";
-+			reg = <0xc0000 0x1e80000>;
-+		};
-+	};
- };
- 
- &mdio {