mvebu: add support for Check Point V-81

Check Point V-80 (Quantum Spark 1590 Appliance) is an Appliance, based
on Armada 8040 (88F8040).

Specification:

- SoC             : Marvell Armada 8040 (88F8040)
- RAM             : DDR4 2 GiB (4x 512 MiB chip)
- Flash           : eMMC 4 GiB
- Ethernet        : 10x 10/100/1000 Mbps
  - LAN 1-8       : Marvell 88E6393X
  - WAN           : Marvell 88E1512
  - DMZ           : Marvell 88E1512 (RJ-45/SFP combo)
- LEDs/Keys (GPIO): 11x/1x
- UART            : "CONSOLE" port (USB 1.1 Type-C)
  - chip          : Silicon Labs CP2102N
  - port          : ttyS0
  - settings      : 115200bps 8n1
- HW Monitoring   : 2x nuvoTon NCT7802Y
- USB             : USB 3.0 Type-A
- Power           : 12 VDC, 3.3 A
  - plug          : DC Plug 2.5/5.5 mm (inner/outer)

Flash instruction (common):

1. Boot V-81 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
   CLI by `expert` command
3. Update U-Boot environment variables by the following commands

   fw_setenv bootcmd_ow_usb 'usb start; load usb 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
   fw_setenv bootcmd_ow_sd 'load mmc 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
   fw_setenv bootcmd_ow_emmc 'run set_mmc_internal; mmc read ${loadaddr} ${prim_header_mmc_blk} 4 && source ${loadaddr}'
   fw_setenv bootcmd 'run bootcmd_ow_usb; run bootcmd_ow_sd; run bootcmd_ow_emmc; run bootcmd_part${activePartition};'

   Attention: don't forget single quatations of values to prevent
              expansion of variables

4. Turn off the device

Flash instruction (USB-boot/SD-boot):

1. Extract and burn (squashfs|ext4)-sdcard.img.gz to USB storage or
   MicroSD card
2. Connect that storage to V-81
3. Turn on V-81 and it will be booted with OpenWrt in that USB storage

Flash instruction (eMMC-boot):

1. Copy initramfs image, dtb and bootsctipt to the USB storage with
   renaming

   initramfs.bin -------> Image
   dtb -----------------> armada-8040-v-81.dtb
   bootscript (.scr) ---> boot.scr

2. Connect that storage to the USB 3.0 port on V-81
3. Turn on V-81 and it will be booted with OpenWrt initramfs image in
   that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-81
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing

Reverting to stock firmware:

1. Turn on V-81 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting

Notes:

- The partition table in the internal eMMC has single partition, but
  "blkdevparts=" parameter will be passed from the bootloader and that
  definition will be used instead.

- The port-side LED pairs of RJ-45/SFP ports on V-81 are switched by a
  GPIO pin of pin7 on &cp0_gpio2. (High(1): RJ-45, Low(0): SFP)
  This needs to be switched manually.

- The MicroSD card slot is too unstable and the following messages are
  printed without "marvell,xenon-phy-slow-mode;" property.

  [   97.060851] mmc0: error -84 whilst initialising SD card
  [   97.137049] mmc0: error -84 whilst initialising SD card
  [   97.214315] mmc0: error -84 whilst initialising SD card
  ...

- There are no detailed information about maximum power consumption
  limit of the SFP port or optional DSL-SFP modules sold officially.
  But the power requirement of almost DSL-SFP modules are 3.3V/700mA, so
  set the maximum value of the SFP port to 2000 mW (Power Level III).

- Do not insert a MicroSD card before turning of the device when OpenWrt
  installation. The stock firmware deletes all files in the first
  partition automatically, to use it as a storage for logs.

MAC addresses:

LAN: 00:1C:7F:xx:xx:FA (mmcblk1boot0, ethaddr  (text))
WAN: 00:1C:7F:xx:xx:F9 (mmcblk1boot0, eth2addr (text))
DMZ: 00:1C:7F:xx:xx:FB (mmcblk1boot0, eth1addr (text))

Signed-off-by: INAGAKI Hiroshi <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <[email protected]>

target/linux/mvebu/cortexa72/base-files/etc/board.d/02_network

@@ -13,6 +13,9 @@ case "$board" in
 checkpoint,v-80)
 	ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1"
 	;;
+checkpoint,v-81)
+	ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8" "eth1 eth2"
+	;;
 globalscale,mochabin)
 	ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" "eth0 eth2"
 	;;

target/linux/mvebu/cortexa72/base-files/lib/upgrade/platform.sh

@@ -9,7 +9,8 @@ REQUIRE_IMAGE_METADATA=1
 
 platform_check_image() {
 	case "$(board_name)" in
-	checkpoint,v-80)
+	checkpoint,v-80|\
+	checkpoint,v-81)
 		local root="$(cmdline_get_var root)"
 		case "$root" in
 		PARTUUID=????????-02) # USB or SD
@@ -55,7 +56,8 @@ platform_check_image() {
 
 platform_do_upgrade() {
 	case "$(board_name)" in
-	checkpoint,v-80)
+	checkpoint,v-80|\
+	checkpoint,v-81)
 		local root="$(cmdline_get_var root)"
 		case "$root" in
 		PARTUUID=????????-02) # USB or SD
@@ -91,7 +93,8 @@ platform_do_upgrade() {
 }
 platform_copy_config() {
 	case "$(board_name)" in
-	checkpoint,v-80)
+	checkpoint,v-80|\
+	checkpoint,v-81)
 		local root="$(cmdline_get_var root)"
 		case "$root" in
 		PARTUUID=????????-02) # USB or SD

target/linux/mvebu/files-6.12/arch/arm64/boot/dts/marvell/armada-8040-v-81.dts

@@ -0,0 +1,514 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-8040.dtsi"
+
+/ {
+	model = "Check Point V-81";
+	compatible = "checkpoint,v-81", "marvell,armada8040",
+		     "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp1_eth1;
+		ethernet2 = &cp1_eth2;
+		mmc0 = &ap_sdhci0;
+		mmc1 = &cp0_sdhci0;
+		led-boot = &led_power_blue;
+		led-failsafe = &led_power_red;
+		led-running = &led_power_blue;
+		led-upgrade = &led_power_blue;
+		label-mac-device = &cp1_eth2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x80000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_gpio_keys_pins>;
+		pinctrl-names = "default";
+
+		button-reset {
+			label = "reset";
+			gpios = <&cp1_gpio1 31 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_gpio_leds_pins>;
+		pinctrl-names = "default";
+
+		led-0 {
+			gpios = <&cp1_gpio1 2 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_RED>;
+			function = "management";
+		};
+
+		led-1 {
+			gpios = <&cp1_gpio1 3 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = "management";
+		};
+
+		led-2 {
+			gpios = <&cp1_gpio1 6 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WAN_ONLINE;
+		};
+
+		led-3 {
+			gpios = <&cp1_gpio1 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WAN_ONLINE;
+		};
+
+		led_power_red: led-4 {
+			gpios = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+		};
+
+		/* populated but no hole on the case ("LTE" or "DSL") */
+		led-5 {
+			gpios = <&cp1_gpio1 14 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_MOBILE;
+		};
+
+		/* populated but no hole on the case ("LTE" or "DSL") */
+		led-6 {
+			gpios = <&cp1_gpio1 15 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_MOBILE;
+		};
+
+		/* populated but no hole on the case */
+		led-7 {
+			gpios = <&cp1_gpio1 16 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WLAN;
+		};
+
+		/* populated but no hole on the case */
+		led-8 {
+			gpios = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WLAN;
+		};
+
+		led_power_blue: led-9 {
+			gpios = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_POWER;
+		};
+
+		/* populated but no hole on the case (unused) */
+		led-10 {
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = "unused";
+		};
+	};
+
+	regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-vbus";
+		gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	sfp: sfp {
+		/*
+		 * Note: port LEDs on RJ45/SFP are switched
+		 *       by pin7 on &cp0_gpio2
+		 *
+		 * - HIGH: RJ45
+		 * - LOW : SFP
+		 */
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_i2c1>;
+		los-gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <2000>;
+	};
+};
+
+/* USB Type-C UART console */
+&uart0 {
+	status = "okay";
+
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+};
+
+&ap_pinctrl {
+	pmx_ap_sdhci0_pins: ap-sdhci0-pins {
+		marvell,pins = "mpp12";
+		marvell,function = "gpio";
+	};
+};
+
+/* MicroSD slot */
+&ap_sdhci0 {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_ap_sdhci0_pins>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	cd-gpios = <&ap_gpio 12 GPIO_ACTIVE_LOW>;
+	/*
+	 * Not stable in HS modes - phy needs "more calibration", so add
+	 * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes.
+	 */
+	marvell,xenon-phy-slow-mode;
+	no-1-8-v;
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* LAN1-8 (Switch) */
+&cp0_eth0 {
+	status = "okay";
+
+	phy-connection-type = "10gbase-r";
+	phys = <&cp0_comphy2 0>;
+
+	fixed-link {
+		speed = <10000>;
+		full-duplex;
+	};
+};
+
+/* 2x PCA9555, 2x NCT7802Y, TCA9534A */
+&cp0_i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmx_cp0_i2c0_pins>;
+	clock-frequency = <100000>;
+
+	gpio3: gpio@21 {
+		pinctrl-0 = <&pmx_pca9555_pins>;
+		pinctrl-names = "default";
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&cp0_gpio2>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio4: gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	hwmon@2b {
+		compatible = "nuvoton,nct7802";
+		reg = <0x2b>;
+	};
+
+	hwmon@2d {
+		compatible = "nuvoton,nct7802";
+		reg = <0x2d>;
+	};
+
+	/* TI TCA9534A */
+	gpio5: gpio@3b {
+		compatible = "nxp,pca9534";
+		reg = <0x3b>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+/* EEPROM */
+&cp0_i2c1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmx_cp0_i2c1_pins>;
+	clock-frequency = <100000>;
+
+	/* Giantec GT24C04A */
+	eeprom@54 {
+		compatible = "atmel,24c04";
+		reg = <0x54>;
+		wp-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+		read-only;
+	};
+};
+
+&cp0_mdio {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_cp0_mdio_pins>;
+	pinctrl-names = "default";
+
+	/* Marvell 88E6393X */
+	switch@0 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				ethernet = <&cp0_eth0>;
+				phy-connection-type = "10gbase-r";
+
+				fixed-link {
+					speed = <10000>;
+					full-duplex;
+				};
+			};
+
+			swport1: port@1 {
+				reg = <1>;
+				label = "lan1";
+				phy-handle = <&swphy1>;
+			};
+
+			swport2: port@2 {
+				reg = <2>;
+				label = "lan2";
+				phy-handle = <&swphy2>;
+			};
+
+			swport3: port@3 {
+				reg = <3>;
+				label = "lan3";
+				phy-handle = <&swphy3>;
+			};
+
+			swport4: port@4 {
+				reg = <4>;
+				label = "lan4";
+				phy-handle = <&swphy4>;
+			};
+
+			swport5: port@5 {
+				reg = <5>;
+				label = "lan5";
+				phy-handle = <&swphy5>;
+			};
+
+			swport6: port@6 {
+				reg = <6>;
+				label = "lan6";
+				phy-handle = <&swphy6>;
+			};
+
+			swport7: port@7 {
+				reg = <7>;
+				label = "lan7";
+				phy-handle = <&swphy7>;
+			};
+
+			swport8: port@8 {
+				reg = <8>;
+				label = "lan8";
+				phy-handle = <&swphy8>;
+			};
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			swphy1: switch-phy@1 {
+				reg = <0x1>;
+			};
+
+			swphy2: switch-phy@2 {
+				reg = <0x2>;
+			};
+
+			swphy3: switch-phy@3 {
+				reg = <0x3>;
+			};
+
+			swphy4: switch-phy@4 {
+				reg = <0x4>;
+			};
+
+			swphy5: switch-phy@5 {
+				reg = <0x5>;
+			};
+
+			swphy6: switch-phy@6 {
+				reg = <0x6>;
+			};
+
+			swphy7: switch-phy@7 {
+				reg = <0x7>;
+			};
+
+			swphy8: switch-phy@8 {
+				reg = <0x8>;
+			};
+		};
+	};
+};
+
+&cp0_pinctrl {
+	pmx_cp0_mdio_pins: cp0-mdio-pins {
+		marvell,pins = "mpp32", "mpp34";
+		marvell,function = "ge";
+	};
+
+	pmx_cp0_spi1_pins: cp0-spi0-pins {
+		marvell,pins = "mpp40", "mpp41", "mpp42", "mpp43";
+		marvell,function = "spi0";
+	};
+
+	pmx_cp0_i2c0_pins: cp0-i2c0-pins {
+		marvell,pins = "mpp37", "mpp38";
+		marvell,function = "i2c0";
+	};
+
+	pmx_cp0_i2c1_pins: cp0-i2c1-pins {
+		marvell,pins = "mpp35", "mpp36";
+		marvell,function = "i2c1";
+	};
+
+	pmx_cp0_sdhci0_pins: cp0-sdhci0-pins {
+		marvell,pins = "mpp56", "mpp57","mpp58", "mpp59", "mpp60", "mpp61";
+		marvell,function = "sdio";
+	};
+
+	pmx_cp1_rgmii1_pins: cp1-rgmii1-pins {
+		marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49",
+			       "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55";
+		marvell,function = "ge1";
+	};
+
+	pmx_pca9555_pins: pca9555-pins {
+		marvell,pins = "mpp33";
+		marvell,function = "gpio";
+	};
+};
+
+/* eMMC */
+&cp0_sdhci0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmx_cp0_sdhci0_pins>;
+	bus-width = <4>;
+	non-removable;
+};
+
+&cp0_utmi {
+	status = "okay";
+};
+
+/* USB 3.0 Type-A */
+&cp0_usb3_0 {
+	status = "okay";
+
+	dr_mode = "host";
+	phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+	phy-names = "cp0-usb3h0-comphy", "utmi";
+};
+
+&cp1_ethernet {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_cp1_rgmii1_pins>;
+	pinctrl-names = "default";
+};
+
+/* "DMZ" (RJ45/SFP) */
+&cp1_eth1 {
+	status = "okay";
+
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy0>;
+};
+
+/* "WAN" */
+&cp1_eth2 {
+	status = "okay";
+
+	phy-connection-type = "sgmii";
+	phy-handle = <&ethphy1>;
+	phys = <&cp1_comphy1 2>;
+};
+
+&cp1_mdio {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_cp1_mdio_pins>;
+	pinctrl-names = "default";
+
+	/* Marvell 88E1512 */
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0141,0dd1",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		/*
+		 * LED[0] (Green): LINK/ACT
+		 * LED[1] (Amber): SPEED 100/1000M
+		 */
+		marvell,reg-init = <3 16 0 0x61>;
+		sfp = <&sfp>;
+	};
+
+	/* Marvell 88E1512 */
+	ethphy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0141,0dd1",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		/*
+		 * LED[0] (Green): LINK/ACT
+		 * LED[1] (Amber): SPEED 100/1000M
+		 */
+		marvell,reg-init = <3 16 0 0x61>;
+	};
+};
+
+&cp1_pinctrl {
+	pmx_gpio_keys_pins: gpio-keys-pins {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+
+	pmx_gpio_leds_pins: gpio-leds-pins {
+		marvell,pins = "mpp2", "mpp3", "mpp6", "mpp7", "mpp11", "mpp14",
+			       "mpp15", "mpp16", "mpp24", "mpp26";
+		marvell,function = "gpio";
+	};
+
+	pmx_cp1_mdio_pins: mdio-pins {
+		marvell,pins = "mpp4", "mpp5";
+		marvell,function = "ge";
+	};
+};

target/linux/mvebu/files-6.6/arch/arm64/boot/dts/marvell/armada-8040-v-81.dts

@@ -0,0 +1,514 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-8040.dtsi"
+
+/ {
+	model = "Check Point V-81";
+	compatible = "checkpoint,v-81", "marvell,armada8040",
+		     "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp1_eth1;
+		ethernet2 = &cp1_eth2;
+		mmc0 = &ap_sdhci0;
+		mmc1 = &cp0_sdhci0;
+		led-boot = &led_power_blue;
+		led-failsafe = &led_power_red;
+		led-running = &led_power_blue;
+		led-upgrade = &led_power_blue;
+		label-mac-device = &cp1_eth2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x80000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_gpio_keys_pins>;
+		pinctrl-names = "default";
+
+		button-reset {
+			label = "reset";
+			gpios = <&cp1_gpio1 31 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_gpio_leds_pins>;
+		pinctrl-names = "default";
+
+		led-0 {
+			gpios = <&cp1_gpio1 2 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_RED>;
+			function = "management";
+		};
+
+		led-1 {
+			gpios = <&cp1_gpio1 3 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = "management";
+		};
+
+		led-2 {
+			gpios = <&cp1_gpio1 6 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WAN_ONLINE;
+		};
+
+		led-3 {
+			gpios = <&cp1_gpio1 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WAN_ONLINE;
+		};
+
+		led_power_red: led-4 {
+			gpios = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+		};
+
+		/* populated but no hole on the case ("LTE" or "DSL") */
+		led-5 {
+			gpios = <&cp1_gpio1 14 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_MOBILE;
+		};
+
+		/* populated but no hole on the case ("LTE" or "DSL") */
+		led-6 {
+			gpios = <&cp1_gpio1 15 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_MOBILE;
+		};
+
+		/* populated but no hole on the case */
+		led-7 {
+			gpios = <&cp1_gpio1 16 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WLAN;
+		};
+
+		/* populated but no hole on the case */
+		led-8 {
+			gpios = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WLAN;
+		};
+
+		led_power_blue: led-9 {
+			gpios = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_POWER;
+		};
+
+		/* populated but no hole on the case (unused) */
+		led-10 {
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = "unused";
+		};
+	};
+
+	regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-vbus";
+		gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	sfp: sfp {
+		/*
+		 * Note: port LEDs on RJ45/SFP are switched
+		 *       by pin7 on &cp0_gpio2
+		 *
+		 * - HIGH: RJ45
+		 * - LOW : SFP
+		 */
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_i2c1>;
+		los-gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <2000>;
+	};
+};
+
+/* USB Type-C UART console */
+&uart0 {
+	status = "okay";
+
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+};
+
+&ap_pinctrl {
+	pmx_ap_sdhci0_pins: ap-sdhci0-pins {
+		marvell,pins = "mpp12";
+		marvell,function = "gpio";
+	};
+};
+
+/* MicroSD slot */
+&ap_sdhci0 {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_ap_sdhci0_pins>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	cd-gpios = <&ap_gpio 12 GPIO_ACTIVE_LOW>;
+	/*
+	 * Not stable in HS modes - phy needs "more calibration", so add
+	 * the "slow-mode" and disable SDR104, SDR50 and DDR50 modes.
+	 */
+	marvell,xenon-phy-slow-mode;
+	no-1-8-v;
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* LAN1-8 (Switch) */
+&cp0_eth0 {
+	status = "okay";
+
+	phy-connection-type = "10gbase-r";
+	phys = <&cp0_comphy2 0>;
+
+	fixed-link {
+		speed = <10000>;
+		full-duplex;
+	};
+};
+
+/* 2x PCA9555, 2x NCT7802Y, TCA9534A */
+&cp0_i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmx_cp0_i2c0_pins>;
+	clock-frequency = <100000>;
+
+	gpio3: gpio@21 {
+		pinctrl-0 = <&pmx_pca9555_pins>;
+		pinctrl-names = "default";
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&cp0_gpio2>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio4: gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	hwmon@2b {
+		compatible = "nuvoton,nct7802";
+		reg = <0x2b>;
+	};
+
+	hwmon@2d {
+		compatible = "nuvoton,nct7802";
+		reg = <0x2d>;
+	};
+
+	/* TI TCA9534A */
+	gpio5: gpio@3b {
+		compatible = "nxp,pca9534";
+		reg = <0x3b>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+/* EEPROM */
+&cp0_i2c1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmx_cp0_i2c1_pins>;
+	clock-frequency = <100000>;
+
+	/* Giantec GT24C04A */
+	eeprom@54 {
+		compatible = "atmel,24c04";
+		reg = <0x54>;
+		wp-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+		read-only;
+	};
+};
+
+&cp0_mdio {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_cp0_mdio_pins>;
+	pinctrl-names = "default";
+
+	/* Marvell 88E6393X */
+	switch@0 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				ethernet = <&cp0_eth0>;
+				phy-connection-type = "10gbase-r";
+
+				fixed-link {
+					speed = <10000>;
+					full-duplex;
+				};
+			};
+
+			swport1: port@1 {
+				reg = <1>;
+				label = "lan1";
+				phy-handle = <&swphy1>;
+			};
+
+			swport2: port@2 {
+				reg = <2>;
+				label = "lan2";
+				phy-handle = <&swphy2>;
+			};
+
+			swport3: port@3 {
+				reg = <3>;
+				label = "lan3";
+				phy-handle = <&swphy3>;
+			};
+
+			swport4: port@4 {
+				reg = <4>;
+				label = "lan4";
+				phy-handle = <&swphy4>;
+			};
+
+			swport5: port@5 {
+				reg = <5>;
+				label = "lan5";
+				phy-handle = <&swphy5>;
+			};
+
+			swport6: port@6 {
+				reg = <6>;
+				label = "lan6";
+				phy-handle = <&swphy6>;
+			};
+
+			swport7: port@7 {
+				reg = <7>;
+				label = "lan7";
+				phy-handle = <&swphy7>;
+			};
+
+			swport8: port@8 {
+				reg = <8>;
+				label = "lan8";
+				phy-handle = <&swphy8>;
+			};
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			swphy1: switch-phy@1 {
+				reg = <0x1>;
+			};
+
+			swphy2: switch-phy@2 {
+				reg = <0x2>;
+			};
+
+			swphy3: switch-phy@3 {
+				reg = <0x3>;
+			};
+
+			swphy4: switch-phy@4 {
+				reg = <0x4>;
+			};
+
+			swphy5: switch-phy@5 {
+				reg = <0x5>;
+			};
+
+			swphy6: switch-phy@6 {
+				reg = <0x6>;
+			};
+
+			swphy7: switch-phy@7 {
+				reg = <0x7>;
+			};
+
+			swphy8: switch-phy@8 {
+				reg = <0x8>;
+			};
+		};
+	};
+};
+
+&cp0_pinctrl {
+	pmx_cp0_mdio_pins: cp0-mdio-pins {
+		marvell,pins = "mpp32", "mpp34";
+		marvell,function = "ge";
+	};
+
+	pmx_cp0_spi1_pins: cp0-spi0-pins {
+		marvell,pins = "mpp40", "mpp41", "mpp42", "mpp43";
+		marvell,function = "spi0";
+	};
+
+	pmx_cp0_i2c0_pins: cp0-i2c0-pins {
+		marvell,pins = "mpp37", "mpp38";
+		marvell,function = "i2c0";
+	};
+
+	pmx_cp0_i2c1_pins: cp0-i2c1-pins {
+		marvell,pins = "mpp35", "mpp36";
+		marvell,function = "i2c1";
+	};
+
+	pmx_cp0_sdhci0_pins: cp0-sdhci0-pins {
+		marvell,pins = "mpp56", "mpp57","mpp58", "mpp59", "mpp60", "mpp61";
+		marvell,function = "sdio";
+	};
+
+	pmx_cp1_rgmii1_pins: cp1-rgmii1-pins {
+		marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49",
+			       "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55";
+		marvell,function = "ge1";
+	};
+
+	pmx_pca9555_pins: pca9555-pins {
+		marvell,pins = "mpp33";
+		marvell,function = "gpio";
+	};
+};
+
+/* eMMC */
+&cp0_sdhci0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmx_cp0_sdhci0_pins>;
+	bus-width = <4>;
+	non-removable;
+};
+
+&cp0_utmi {
+	status = "okay";
+};
+
+/* USB 3.0 Type-A */
+&cp0_usb3_0 {
+	status = "okay";
+
+	dr_mode = "host";
+	phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+	phy-names = "cp0-usb3h0-comphy", "utmi";
+};
+
+&cp1_ethernet {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_cp1_rgmii1_pins>;
+	pinctrl-names = "default";
+};
+
+/* "DMZ" (RJ45/SFP) */
+&cp1_eth1 {
+	status = "okay";
+
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy0>;
+};
+
+/* "WAN" */
+&cp1_eth2 {
+	status = "okay";
+
+	phy-connection-type = "sgmii";
+	phy-handle = <&ethphy1>;
+	phys = <&cp1_comphy1 2>;
+};
+
+&cp1_mdio {
+	status = "okay";
+
+	pinctrl-0 = <&pmx_cp1_mdio_pins>;
+	pinctrl-names = "default";
+
+	/* Marvell 88E1512 */
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0141,0dd1",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		/*
+		 * LED[0] (Green): LINK/ACT
+		 * LED[1] (Amber): SPEED 100/1000M
+		 */
+		marvell,reg-init = <3 16 0 0x61>;
+		sfp = <&sfp>;
+	};
+
+	/* Marvell 88E1512 */
+	ethphy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id0141,0dd1",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		/*
+		 * LED[0] (Green): LINK/ACT
+		 * LED[1] (Amber): SPEED 100/1000M
+		 */
+		marvell,reg-init = <3 16 0 0x61>;
+	};
+};
+
+&cp1_pinctrl {
+	pmx_gpio_keys_pins: gpio-keys-pins {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+
+	pmx_gpio_leds_pins: gpio-leds-pins {
+		marvell,pins = "mpp2", "mpp3", "mpp6", "mpp7", "mpp11", "mpp14",
+			       "mpp15", "mpp16", "mpp24", "mpp26";
+		marvell,function = "gpio";
+	};
+
+	pmx_cp1_mdio_pins: mdio-pins {
+		marvell,pins = "mpp4", "mpp5";
+		marvell,function = "ge";
+	};
+};

target/linux/mvebu/image/cortexa72.mk

@@ -33,6 +33,24 @@ define Device/checkpoint_v-80
 endef
 TARGET_DEVICES += checkpoint_v-80
 
+define Device/checkpoint_v-81
+  $(call Device/Default-arm64)
+  DEVICE_VENDOR := Check Point
+  DEVICE_MODEL := V-81
+  SOC := armada-8040
+  BOOT_SCRIPT := v-80
+  IMAGES += sysupgrade.gz
+  IMAGE/sysupgrade.gz := boot-scr eMMC | append-bootscript | pad-to 2048 | \
+	append-kernel | \
+	sysupgrade-tar kernel=$$$$@ dtb=$$(KDIR)/image-$$(DEVICE_DTS).dtb | \
+	gzip | append-metadata
+  ARTIFACTS := initramfs.dtb initramfs.scr
+  ARTIFACT/initramfs.dtb := append-dtb
+  ARTIFACT/initramfs.scr := boot-scr INIT | append-bootscript
+  DEVICE_PACKAGES := kmod-dsa-mv88e6xxx kmod-hwmon-nct7802 kmod-rtc-ds1307
+endef
+TARGET_DEVICES += checkpoint_v-81
+
 define Device/globalscale_mochabin
   $(call Device/Default-arm64)
   DEVICE_VENDOR := Globalscale