ipq40xx: refactor ZTE MF287 series

The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.

Signed-off-by: Andreas Böhler <[email protected]>

package/firmware/ipq-wifi/Makefile

@@ -43,6 +43,7 @@ ALLWIFIBOARDS:= \
 	xiaomi_ax9000 \
 	yyets_le1 \
 	zte_mf289f \
+	zte_mf287 \
 	zte_mf287plus \
 	zyxel_nbg7815
 
@@ -133,6 +134,7 @@ $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
 $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
 $(eval $(call generate-ipq-wifi-package,yyets_le1,YYeTs LE1))
 $(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
+$(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287))
 $(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
 $(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
 

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -114,6 +114,7 @@ ipq40xx_setup_interfaces()
 	zte,mf286d)
 		ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan"
 		;;
+	zte,mf287|\
 	zte,mf287plus|\
 	zte,mf287pro)
 		ucidef_set_interface_lan "lan1 lan2 lan3 lan4"

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -27,6 +27,7 @@ EOF
 		;;
 	zte,mf18a |\
 	zte,mf286d |\
+	zte,mf287|\
 	zte,mf287plus |\
 	zte,mf287pro |\
 	zte,mf289f)

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dts

@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2022, Pawel Dembicki <[email protected]>.
+// Copyright (c) 2022, Giammarco Marzano <[email protected]>.
+// Copyright (c) 2023, Andreas Böhler <[email protected]>
+
+#include "qcom-ipq4018-mf287_common.dtsi"
+
+/ {
+	model = "ZTE MF287";
+	compatible = "zte,mf287";
+
+	/*
+	 * This node is used to restart modem module to avoid anomalous
+	 * behaviours on initial communication.
+	 */
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&key_reset {
+	gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+};
+
+&key_wps {
+	gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+};
+
+&led_status {
+	gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+		   <&tlmm 59 GPIO_ACTIVE_HIGH>,
+		   <&tlmm 1 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "0:SBL1";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "0:MIBIB";
+				reg = <0x40000 0x20000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "0:QSEE";
+				reg = <0x60000 0x60000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "0:CDT";
+				reg = <0xc0000 0x10000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0xd0000 0x10000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0xe0000 0x10000>;
+				read-only;
+			};
+
+			partition@f0000 {
+				label = "0:APPSBL";
+				reg = <0xf0000 0xc0000>;
+				read-only;
+			};
+
+			partition@1b0000 {
+				label = "0:reserved1";
+				reg = <0x1b0000 0x50000>;
+				read-only;
+			};
+		};
+	};
+
+	spi-nand@1 { /* flash@1 ? */
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "fota-flag";
+				reg = <0x0 0x140000>;
+				read-only;
+			};
+
+			partition@140000 {
+				label = "ART";
+				reg = <0x140000 0x140000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				precal_art_1000: precal@1000 {
+					reg = <0x1000 0x2f20>;
+				};
+
+				precal_art_5000: precal@5000 {
+					reg = <0x5000 0x2f20>;
+				};
+			};
+
+			partition@280000 {
+				label = "mac";
+				reg = <0x280000 0x140000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				macaddr_mac_0: macaddr@0 {
+					reg = <0x0 0x6>;
+				};
+			};
+
+			partition@3c0000 {
+				label = "cfg-param";
+				reg = <0x3c0000 0x600000>;
+				read-only;
+			};
+
+			partition@9c0000 {
+				label = "oops";
+				reg = <0x9c0000 0x140000>;
+			};
+
+			partition@b00000 {
+				label = "web";
+				reg = <0xb00000 0x800000>;
+			};
+
+			partition@1300000 {
+				label = "rootfs";
+				reg = <0x1300000 0x2200000>;
+			};
+
+			partition@3500000 {
+				label = "data";
+				reg = <0x3500000 0x1900000>;
+			};
+
+			partition@4e00000 {
+				label = "fota";
+				reg = <0x4e00000 0x3200000>;
+			};
+		};
+	};
+
+	zigbee@2 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "silabs,em3581";
+		reg = <2>;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio59", "gpio1";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&wifi0 {
+	qcom,ath10k-calibration-variant = "zte,mf287";
+};
+
+&wifi1{
+	qcom,ath10k-calibration-variant = "zte,mf287";
+};

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287.dtsi → target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287_common.dtsi

@@ -171,7 +171,6 @@
 	status = "okay";
 	nvmem-cell-names = "pre-calibration", "mac-address";
 	nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>;
-	qcom,ath10k-calibration-variant = "zte,mf287plus";
 };
 
 &wifi1 {
@@ -179,5 +178,4 @@
 	nvmem-cell-names = "pre-calibration", "mac-address";
 	nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>;
 	mac-address-increment = <1>;
-	qcom,ath10k-calibration-variant = "zte,mf287plus";
 };

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts

@@ -3,7 +3,7 @@
 // Copyright (c) 2022, Giammarco Marzano <[email protected]>.
 // Copyright (c) 2023, Andreas Böhler <[email protected]>
 
-#include "qcom-ipq4018-mf287.dtsi"
+#include "qcom-ipq4018-mf287_common.dtsi"
 
 / {
 	model = "ZTE MF287Plus";
@@ -216,3 +216,11 @@
 		};
 	};
 };
+
+&wifi0 {
+	qcom,ath10k-calibration-variant = "zte,mf287plus";
+};
+
+&wifi1{
+	qcom,ath10k-calibration-variant = "zte,mf287plus";
+};

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287pro.dts

@@ -3,7 +3,7 @@
 // Copyright (c) 2022, Giammarco Marzano <[email protected]>.
 // Copyright (c) 2023, Andreas Böhler <[email protected]>
 
-#include "qcom-ipq4018-mf287.dtsi"
+#include "qcom-ipq4018-mf287_common.dtsi"
 
 / {
 	model = "ZTE MF287Pro";
@@ -263,3 +263,13 @@
 		};
 	};
 };
+
+/* The MF287Plus and MF287Pro share the same board data file */
+&wifi0 {
+	qcom,ath10k-calibration-variant = "zte,mf287plus";
+};
+
+/* The MF287Plus and MF287Pro share the same board data file */
+&wifi1{
+	qcom,ath10k-calibration-variant = "zte,mf287plus";
+};

target/linux/ipq40xx/image/generic.mk

@@ -1168,7 +1168,6 @@ TARGET_DEVICES += zte_mf286d
 
 define Device/zte_mf287_common
 	$(call Device/zte_mf28x_common)
-	DEVICE_PACKAGES += ipq-wifi-zte_mf287plus
 	SOC := qcom-ipq4018
 #	The recovery image is used to return back to stock (an initramfs-based image
 #	that can be flashed to the device via sysupgrade
@@ -1181,15 +1180,23 @@ endef
 
 define Device/zte_mf287plus
 	$(call Device/zte_mf287_common)
+	DEVICE_PACKAGES += ipq-wifi-zte_mf287plus
 	DEVICE_DTS_CONFIG := [email protected]
 	DEVICE_MODEL := MF287Plus
-	DEVICE_ALT0_VENDOR := ZTE
-	DEVICE_ALT0_MODEL := MF287
 endef
 TARGET_DEVICES += zte_mf287plus
 
+define Device/zte_mf287
+	$(call Device/zte_mf287_common)
+	DEVICE_PACKAGES += ipq-wifi-zte_mf287
+	DEVICE_DTS_CONFIG := [email protected]
+	DEVICE_MODEL := MF287
+endef
+TARGET_DEVICES += zte_mf287
+
 define Device/zte_mf287pro
 	$(call Device/zte_mf287_common)
+	DEVICE_PACKAGES += ipq-wifi-zte_mf287plus
 	DEVICE_DTS_CONFIG := [email protected]
 	DEVICE_MODEL := MF287Pro
 endef