|
|
@@ -0,0 +1,341 @@
|
|
|
+#include "qcom-ipq8065-v1.0.dtsi"
|
|
|
+
|
|
|
+#include <dt-bindings/input/input.h>
|
|
|
+
|
|
|
+/ {
|
|
|
+ model = "ZyXEL NBG6817";
|
|
|
+ compatible = "zyxel,nbg6817", "qcom,ipq8065";
|
|
|
+
|
|
|
+ memory@0 {
|
|
|
+ reg = <0x42000000 0x1e000000>;
|
|
|
+ device_type = "memory";
|
|
|
+ };
|
|
|
+
|
|
|
+ reserved-memory {
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <1>;
|
|
|
+ ranges;
|
|
|
+ rsvd@41200000 {
|
|
|
+ reg = <0x41200000 0x300000>;
|
|
|
+ no-map;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ aliases {
|
|
|
+ serial0 = &uart4;
|
|
|
+ mdio-gpio0 = &mdio0;
|
|
|
+ sdcc1 = &sdcc1;
|
|
|
+ };
|
|
|
+
|
|
|
+ chosen {
|
|
|
+ bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
|
|
|
+ linux,stdout-path = "serial0:115200n8";
|
|
|
+ };
|
|
|
+
|
|
|
+ soc {
|
|
|
+ pinmux@800000 {
|
|
|
+ pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+
|
|
|
+ i2c4_pins: i2c4_pinmux {
|
|
|
+ mux {
|
|
|
+ pins = "gpio12", "gpio13";
|
|
|
+ function = "gsbi4";
|
|
|
+ drive-strength = <12>;
|
|
|
+ bias-disable;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ mdio0_pins: mdio0_pins {
|
|
|
+ mux {
|
|
|
+ pins = "gpio0", "gpio1";
|
|
|
+ function = "gpio";
|
|
|
+ drive-strength = <8>;
|
|
|
+ bias-disable;
|
|
|
+ };
|
|
|
+
|
|
|
+ clk {
|
|
|
+ pins = "gpio1";
|
|
|
+ input-disable;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ rgmii2_pins: rgmii2_pins {
|
|
|
+ mux {
|
|
|
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
|
|
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
|
|
+ function = "rgmii2";
|
|
|
+ drive-strength = <8>;
|
|
|
+ bias-disable;
|
|
|
+ };
|
|
|
+
|
|
|
+ tx {
|
|
|
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
|
|
|
+ input-disable;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ spi_pins: spi_pins {
|
|
|
+ mux {
|
|
|
+ pins = "gpio18", "gpio19", "gpio21";
|
|
|
+ function = "gsbi5";
|
|
|
+ drive-strength = <10>;
|
|
|
+ bias-none;
|
|
|
+ };
|
|
|
+
|
|
|
+ cs {
|
|
|
+ pins = "gpio20";
|
|
|
+ drive-strength = <12>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ gsbi@16300000 {
|
|
|
+ qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
|
+ status = "ok";
|
|
|
+ serial@16340000 {
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+ /*
|
|
|
+ * The i2c device on gsbi4 should not be enabled.
|
|
|
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
|
|
|
+ * RPM usage. Turning this on in kernel manifests as
|
|
|
+ * i2c failure for the RPM.
|
|
|
+ */
|
|
|
+ };
|
|
|
+
|
|
|
+ gsbi5: gsbi@1a200000 {
|
|
|
+ qcom,mode = <GSBI_PROT_SPI>;
|
|
|
+ status = "ok";
|
|
|
+
|
|
|
+ spi4: spi@1a280000 {
|
|
|
+ status = "ok";
|
|
|
+ spi-max-frequency = <50000000>;
|
|
|
+ pinctrl-0 = <&spi_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+
|
|
|
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
|
|
+
|
|
|
+ flash: m25p80@0 {
|
|
|
+ compatible = "s25fl512s";
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <1>;
|
|
|
+ spi-max-frequency = <51200000>;
|
|
|
+ reg = <0>;
|
|
|
+
|
|
|
+ linux,part-probe = "qcom-smem";
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ phy@100f8800 { /* USB3 port 1 HS phy */
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+
|
|
|
+ phy@100f8830 { /* USB3 port 1 SS phy */
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+
|
|
|
+ phy@110f8800 { /* USB3 port 0 HS phy */
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+
|
|
|
+ phy@110f8830 { /* USB3 port 0 SS phy */
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+
|
|
|
+ usb30@0 {
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+
|
|
|
+ usb30@1 {
|
|
|
+ status = "ok";
|
|
|
+ };
|
|
|
+
|
|
|
+ pcie0: pci@1b500000 {
|
|
|
+ status = "ok";
|
|
|
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
|
|
|
+ pinctrl-0 = <&pcie0_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+ };
|
|
|
+
|
|
|
+ pcie1: pci@1b700000 {
|
|
|
+ status = "ok";
|
|
|
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
|
|
|
+ pinctrl-0 = <&pcie1_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+ };
|
|
|
+
|
|
|
+ mdio0: mdio {
|
|
|
+ compatible = "virtual,mdio-gpio";
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
|
|
|
+
|
|
|
+ phy0: ethernet-phy@0 {
|
|
|
+ device_type = "ethernet-phy";
|
|
|
+ reg = <0>;
|
|
|
+ qca,ar8327-initvals = <
|
|
|
+ 0x00004 0x7600000 /* PAD0_MODE */
|
|
|
+ 0x00008 0x1000000 /* PAD5_MODE */
|
|
|
+ 0x0000c 0x80 /* PAD6_MODE */
|
|
|
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
|
|
|
+ 0x000e0 0xc74164de /* SGMII_CTRL */
|
|
|
+ 0x0007c 0x4e /* PORT0_STATUS */
|
|
|
+ 0x00094 0x4e /* PORT6_STATUS */
|
|
|
+ 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
|
|
|
+ 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
|
|
|
+ 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
|
|
|
+ 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
|
|
|
+ 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
|
|
|
+ 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
|
|
|
+ 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
|
|
|
+ 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
|
|
|
+ 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
|
|
|
+ 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
|
|
|
+ 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
|
|
|
+ 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
|
|
|
+ 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
|
|
|
+ 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ phy4: ethernet-phy@4 {
|
|
|
+ device_type = "ethernet-phy";
|
|
|
+ reg = <4>;
|
|
|
+ qca,ar8327-initvals = <
|
|
|
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
|
|
|
+ 0x0000c 0x80 /* PAD6_MODE */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ gmac1: ethernet@37200000 {
|
|
|
+ status = "ok";
|
|
|
+ phy-mode = "rgmii";
|
|
|
+ qcom,id = <1>;
|
|
|
+ qcom,phy_mdio_addr = <4>;
|
|
|
+ qcom,poll_required = <0>;
|
|
|
+ qcom,rgmii_delay = <1>;
|
|
|
+ qcom,phy_mii_type = <0>;
|
|
|
+ qcom,emulation = <0>;
|
|
|
+ qcom,irq = <255>;
|
|
|
+ mdiobus = <&mdio0>;
|
|
|
+
|
|
|
+ fixed-link {
|
|
|
+ speed = <1000>;
|
|
|
+ full-duplex;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ gmac2: ethernet@37400000 {
|
|
|
+ status = "ok";
|
|
|
+ phy-mode = "sgmii";
|
|
|
+ qcom,id = <2>;
|
|
|
+ qcom,phy_mdio_addr = <0>; /* none */
|
|
|
+ qcom,poll_required = <0>; /* no polling */
|
|
|
+ qcom,rgmii_delay = <0>;
|
|
|
+ qcom,phy_mii_type = <1>;
|
|
|
+ qcom,emulation = <0>;
|
|
|
+ qcom,irq = <258>;
|
|
|
+ mdiobus = <&mdio0>;
|
|
|
+
|
|
|
+ fixed-link {
|
|
|
+ speed = <1000>;
|
|
|
+ full-duplex;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ rpm@108000 {
|
|
|
+ pinctrl-0 = <&i2c4_pins>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+ };
|
|
|
+
|
|
|
+ amba {
|
|
|
+ sdcc1: sdcc@12400000 {
|
|
|
+ status = "okay";
|
|
|
+ dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
|
|
|
+ dma-names = "tx", "rx";
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+
|
|
|
+
|
|
|
+ };
|
|
|
+
|
|
|
+ gpio-keys {
|
|
|
+ compatible = "gpio-keys";
|
|
|
+ wifi {
|
|
|
+ label = "wifi";
|
|
|
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
|
|
|
+ linux,code = <KEY_RFKILL>;
|
|
|
+ };
|
|
|
+
|
|
|
+ reset {
|
|
|
+ label = "reset";
|
|
|
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
|
|
+ linux,code = <KEY_RESTART>;
|
|
|
+ };
|
|
|
+
|
|
|
+ wps {
|
|
|
+ label = "wps";
|
|
|
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
|
|
+ linux,code = <KEY_WPS_BUTTON>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ gpio-leds {
|
|
|
+ compatible = "gpio-leds";
|
|
|
+ internet {
|
|
|
+ label = "nbg6817:white:internet";
|
|
|
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+
|
|
|
+ power {
|
|
|
+ label = "nbg6817:white:power";
|
|
|
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
|
|
+ default-state = "on";
|
|
|
+ };
|
|
|
+
|
|
|
+ wifi {
|
|
|
+ label = "nbg6817:amber:wifi";
|
|
|
+ gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+
|
|
|
+ wifi5g {
|
|
|
+ label = "nbg6817:amber:wifi5g";
|
|
|
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ gpio_export {
|
|
|
+ compatible = "gpio-export";
|
|
|
+ #size-cells = <0>;
|
|
|
+
|
|
|
+ usb0_status {
|
|
|
+ gpio-export,name = "usb0";
|
|
|
+ gpio-export,output = <1>;
|
|
|
+ gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+
|
|
|
+ usb1_status {
|
|
|
+ gpio-export,name = "usb1";
|
|
|
+ gpio-export,output = <1>;
|
|
|
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+ usb1_power {
|
|
|
+ gpio-export,name = "usb1_power";
|
|
|
+ gpio-export,output = <1>;
|
|
|
+ gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+ usb2_power {
|
|
|
+ gpio-export,name = "usb2_power";
|
|
|
+ gpio-export,output = <1>;
|
|
|
+ gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&adm_dma {
|
|
|
+ status = "ok";
|
|
|
+};
|
André Valentin