mvebu: Add support for WD MyCloud EX2 Ultra

Hardware
--------
Marvell Armada 385 (MV88F6820)
1GB RAM
256MB NAND
1x 1Gbit
2x USB 3.0
2x SATA-III
UART: 115200 8N1 3.3V
RTC
Weltrend MCU WT6703F connected via UART1 for Power LED / PWM Fan / hw reset / WoL

Installation
------------
Connect UART 3.3V adapter to JP2  pins: 1-RX / 2-GND / 5-TX

Use USB2.0 FAT32 pendrive with openwrt-mvebu-cortexa9-wd_cloud-ex2-ultra-initramfs-kernel.bin
 1. stop boot by pressing 1
 2. usb start
 3. fatload usb 0:1  0x02000000 openwrt-mvebu-cortexa9-wd_cloud-ex2-ultra-initramfs-kernel.bin;bootm 0x02000000 -
 4. do backup mtd1 mtd3
 5. use sysupgrade

Or tftp
 1. stop boot by pressing 1
 2. setenv ethact egiga2;setenv serverip 192.168.11.114;setenv ipaddr 192.168.11.113
 3. tftpboot 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-ex2-ultra-initramfs-kernel.bin; bootm 0x02000000 -
 4. do backup mtd1 mtd3
 5. use sysupgrade

or Evgeny Kolesnikov <[email protected]> method from his failed PR 2040

- Using original firmware's network settings obtain SSH access to the device.
- Put *-image-cfs-factory.bin and *-uImage-factory.bin images into device's /tmp directory.
- Write kernel (uImage) image 'flash_eraseall /dev/mtd1 && nandwrite --markbad -p /dev/mtd1 /tmp/*-uImage-factory.bin'.
- Write rootfs (image-cfs) image 'ubiformat /dev/mtd3 -f /tmp/*-image.cfs-factory.bin -y'.
- Reboot the device.

Installation (upgrade):

Use *-sysupgrade.bin in a usual way.
Weltrend MCU control is done via uart1 19200
install coreutils-stty
stty -F /dev/ttyS1 raw speed 19200
stty -F /dev/ttyS1 raw speed 19200

PWM Fan Control
off: 00
echo -n -e '\xfa\x02\x00\x00\x00\x00\xfb' > /dev/ttyS1
slow: 5F
echo -n -e '\xfa\x02\x00\x5f\x00\x00\xfb' > /dev/ttyS1
max: FF
echo -n -e '\xfa\x02\x00\xff\x00\x00\xfb' > /dev/ttyS1

Power LED Control
Blue
echo -n -e '\xfa\x26\x00\x11\x00\x01\xfb' > /dev/ttyS1
Red
echo -n -e '\xfa\x26\x00\x14\x00\x01\xfb' > /dev/ttyS1
Orange
echo -n -e '\xfa\x26\x00\x12\x00\x01\xfb' > /dev/ttyS1

more here: https://github.com/c-MM/mcm-daemon/blob/master/mcm.h

Signed-off-by: Robert Senderek <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/17779
(cherry picked from commit 96ad29a0f3e5fd1c05d685aa3cda1e7940fa4e5c)
Link: https://github.com/openwrt/openwrt/pull/21364
Signed-off-by: Hauke Mehrtens <[email protected]>

target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network

@@ -14,6 +14,7 @@ mvebu_setup_interfaces()
 	case "$board" in
 	ctera,c200-v2|\
 	synology,ds213j|\
+	wd,cloud-ex2-ultra|\
 	wd,cloud-mirror-gen2)
 		ucidef_set_interface_lan "eth0" "dhcp"
 		;;
@@ -96,6 +97,7 @@ mvebu_setup_macs()
 		lan_mac=$label_mac
 		wan_mac=$label_mac
 		;;
+	wd,cloud-ex2-ultra|\
 	wd,cloud-mirror-gen2)
 		# mac address is on ubi "config" or ubi "reserve2" in text file.
 		# ubi "reserve2" /dev/mtd7 is twice small and only contains basic OEM factory info

target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh

@@ -32,6 +32,7 @@ platform_do_upgrade() {
 		nand_do_upgrade "$1"
 		;;
 	buffalo,ls421de|\
+	wd,cloud-ex2-ultra|\
 	wd,cloud-mirror-gen2)
 		nand_do_upgrade "$1"
 		;;

target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-ex2-ultra.dts

@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "armada-385-wd_cloud.dtsi"
+
+/ {
+	model = "WD MyCloud Ex2 Ultra";
+	compatible = "wd,cloud-ex2-ultra", "marvell,armada385", "marvell,armada380";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1GB */
+	};
+};

target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts

@@ -1,368 +1,13 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device Tree file for Western Digital My Cloud Mirror Gen 2
- * (BWVZ/Grand Teton)
- *
- * Copyright (C) 2020
- *
- * Based on the code from:
- *
- * Copyright (C) 2019 Evgeny Kolesnikov <[email protected]>
- * Copyright (C) 2016 Martin Mueller <[email protected]>
- * Copyright (C) 2013 Gregory CLEMENT <[email protected]>
- * Copyright (C) 2014 Thomas Petazzoni <[email protected]>
- *
- */
-
 /dts-v1/;
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include "armada-385.dtsi"
+#include "armada-385-wd_cloud.dtsi"
 
 / {
 	model = "WD MyCloud Mirror Gen 2 (BWVZ/Grand Teton)";
 	compatible = "wd,cloud-mirror-gen2", "marvell,armada385", "marvell,armada380";
 
-	aliases {
-		led-boot = &led_boot;
-		led-failsafe = &led_boot;
-		led-upgrade = &led_boot;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-		append-rootblock = "nullparameter="; /* override the bootloader args */
-	};
-
 	memory {
 		device_type = "memory";
-		reg = <0x00000000 0x20000000>; /* 512 MB */
-	};
-
-	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
-		          MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
-		          MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
-		          MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
-		          MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
-
-		internal-regs {
-			timer@c200 {
-				status = "okay";
-			};
-
-			i2c0: i2c@11000 {
-				status = "okay";
-				clock-frequency = <100000>;
-			};
-
-			i2c1: i2c@11100 {
-				status = "okay";
-				clock-frequency = <100000>;
-			};
-
-			serial@12000 {
-				status = "okay";
-			};
-
-			/* Connected to Welltrend 6703F-OG240WT MCU
-			 * which controls power, fan and other things
-			 */
-			serial@12100 {
-				status = "okay";
-			};
-
-			pinctrl@18000 {
-				/* use only one pin for UART1, as mpp20 is used by sata0 */
-				uart1_pins: uart-pins-1 {
-					marvell,pins = "mpp19";
-					marvell,function = "ua1";
-				};
-
-				xhci0_vbus_pins: xhci0-vbus-pins {
-					marvell,pins = "mpp26";
-					marvell,function = "gpio";
-				};
-
-				xhci1_vbus_pins: xhci1-vbus-pins {
-					marvell,pins = "mpp27";
-					marvell,function = "gpio";
-				};
-
-				sata0_pins: sata-pins-0 {
-					marvell,pins = "mpp55";
-					marvell,function = "sata0";
-				};
-
-				sata1_pins: sata-pins-1 {
-					marvell,pins = "mpp56";
-					marvell,function = "sata1";
-				};
-
-				sata_leds: sata-leds {
-					marvell,pins = "mpp43", "mpp52", "mpp53", "mpp54";
-					marvell,function = "gpio";
-				};
-
-				btn_pins: btn-pins {
-					marvell,pins = "mpp50";
-					marvell,function = "gpio";
-				};
-			};
-
-			usb@58000 {
-				status = "okay";
-			};
-
-			phy: mdio@72004 {
-				phy0: ethernet-phy@0 {
-					/* Init ETH LEDs */
-					marvell,reg-init = <3 16 0 0x101e>;
-					reg = <0>;
-				};
-			};
-
-			sata@a8000 {
-				status = "okay";
-			};
-
-			nand-controller@d0000 {
-				status = "okay";
-
-				nand: nand@0 {
-					reg = <0>;
-					label = "pxa3xx_nand-0";
-					nand-rb = <0>;
-					marvell,nand-keep-config;
-					#marvell,nand-enable-arbiter; //optional
-					nand-on-flash-bbt;
-					nand-ecc-strength = <4>;
-					nand-ecc-step-size = <512>;
-
-					partitions {
-						compatible = "fixed-partitions";
-						#address-cells = <1>;
-						#size-cells = <1>;
-
-						partition@0 {
-							label = "U-Boot";
-							reg = <0x00000000 0x00500000>;    /*   5 MB */
-							read-only;
-						};
-
-						partition@500000 {
-							label = "kernel";
-							reg = <0x00500000 0x00500000>;    /*   5 MB */
-						};
-
-						partition@a00000 {
-							label = "uRamdisk";
-							reg = <0x00a00000 0x00500000>;    /*   5 MB */
-							read-only;
-						};
-
-						partition@f00000 {
-							label = "ubi";
-							reg = <0x00f00000 0x0b900000>;    /* 185 MB */
-						};
-
-						partition@c800000 {
-							label = "rescue fw";
-							reg = <0x0c800000 0x00f00000>;    /*  15 MB */
-							read-only;
-						};
-
-						partition@d70000 {
-							label = "config";
-							reg = <0x0d700000 0x01400000>;    /*  20 MB */
-							read-only;
-						};
-
-						partition@eb00000 {
-							label = "reserve1";
-							reg = <0x0eb00000 0x00a00000>;    /*  10 MB */
-							read-only;
-						};
-
-						partition@f500000 {
-							label = "reserve2";
-							reg = <0x0f500000 0x00a00000>;    /*  10 MB */
-							read-only;
-						};
-					};
-				};
-			};
-
-			usb3@f0000 {
-				usb-phy = <&usb3_0_phy>;
-				status = "okay";
-			};
-
-			usb3@f8000 {
-				usb-phy = <&usb3_1_phy>;
-				status = "okay";
-			};
-		};
-	};
-
-	gpio-leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sata_leds>;
-
-		led_boot: s1red {
-			label = "red:hdd1";
-			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
-		};
-		s2red {
-			label = "red:hdd2";
-			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
-		};
-		s1blue {
-			label = "blue:hdd1";
-			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "ata1";
-		};
-		s2blue {
-			label = "blue:hdd2";
-			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "ata2";
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&btn_pins>;
-
-		reset {
-			label = "reset";
-			linux,code = <KEY_RESTART>;  // Restart=0x198, Power=0x116
-			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-			wakeup-source;
-		};
-	};
-
-	usb3_0_phy: usb3_0_phy {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&reg_usb3_0_vbus>;
-	};
-
-	usb3_1_phy: usb3_1_phy {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&reg_usb3_1_vbus>;
-	};
-
-	reg_usb3_0_vbus: usb3-vbus0 {
-		compatible = "regulator-fixed";
-		regulator-name = "usb3-vbus0";
-		pinctrl-names = "default";
-		pinctrl-0 = <&xhci0_vbus_pins>;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		regulator-always-on;
-		gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_usb3_1_vbus: usb3-vbus1 {
-		compatible = "regulator-fixed";
-		regulator-name = "usb3-vbus1";
-		pinctrl-names = "default";
-		pinctrl-0 = <&xhci1_vbus_pins>;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		regulator-always-on;
-		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_sata0: pwr-sata0 {
-		compatible = "regulator-fixed";
-		regulator-name = "pwr_en_sata0";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		enable-active-high;
-		regulator-boot-on;
-		gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_5v_sata0: v5-sata0 {
-		compatible = "regulator-fixed";
-		regulator-name = "v5.0-sata0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&reg_sata0>;
-	};
-
-	reg_12v_sata0: v12-sata0 {
-		compatible = "regulator-fixed";
-		regulator-name = "v12.0-sata0";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		vin-supply = <&reg_sata0>;
-	};
-
-	reg_sata1: pwr-sata1 {
-		compatible = "regulator-fixed";
-		regulator-name = "pwr_en_sata1";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		enable-active-high;
-		regulator-boot-on;
-		gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_5v_sata1: v5-sata1 {
-		compatible = "regulator-fixed";
-		regulator-name = "v5.0-sata1";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&reg_sata1>;
-	};
-
-	reg_12v_sata1: v12-sata1 {
-		compatible = "regulator-fixed";
-		regulator-name = "v12.0-sata1";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		vin-supply = <&reg_sata1>;
-	};
-};
-
-&bm {
-	status = "okay";
-};
-
-&bm_bppi {
-	status = "okay";
-};
-
-&eth2 {
-	status = "okay";
-	phy = <&phy0>;
-	phy-mode = "sgmii";
-	buffer-manager = <&bm>;
-	bm,pool-long = <0>;
-	bm,pool-short = <1>;
-};
-
-&ahci0 {
-	status = "okay";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	sata-port@0 {
-		reg = <0>;
-		target-supply = <&reg_sata0>;
-		#thermal-sensor-cells = <0>;
-	};
-
-	sata-port@1 {
-		reg = <1>;
-		target-supply = <&reg_sata1>;
-		#thermal-sensor-cells = <1>;
+		reg = <0x00000000 0x20000000>; /* 512MB */
 	};
 };

target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud.dtsi

@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Western Digital My Cloud Mirror Gen 2
+ * (BWVZ/Grand Teton)
+ *
+ * Copyright (C) 2020
+ *
+ * Based on the code from:
+ *
+ * Copyright (C) 2019 Evgeny Kolesnikov <[email protected]>
+ * Copyright (C) 2016 Martin Mueller <[email protected]>
+ * Copyright (C) 2013 Gregory CLEMENT <[email protected]>
+ * Copyright (C) 2014 Thomas Petazzoni <[email protected]>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-385.dtsi"
+
+/ {
+	aliases {
+		led-boot = &led_boot;
+		led-failsafe = &led_boot;
+		led-upgrade = &led_boot;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		append-rootblock = "nullparameter="; /* override the bootloader args */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+		          MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+		          MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+		          MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+		          MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+			timer@c200 {
+				status = "okay";
+			};
+
+			i2c0: i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			i2c1: i2c@11100 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			serial@12000 {
+				status = "okay";
+			};
+
+			/* Connected to Welltrend 6703F-OG240WT MCU
+			 * which controls power, fan and other things
+			 */
+			serial@12100 {
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				/* use only one pin for UART1, as mpp20 is used by sata0 */
+				uart1_pins: uart-pins-1 {
+					marvell,pins = "mpp19";
+					marvell,function = "ua1";
+				};
+
+				xhci0_vbus_pins: xhci0-vbus-pins {
+					marvell,pins = "mpp26";
+					marvell,function = "gpio";
+				};
+
+				xhci1_vbus_pins: xhci1-vbus-pins {
+					marvell,pins = "mpp27";
+					marvell,function = "gpio";
+				};
+
+				sata0_pins: sata-pins-0 {
+					marvell,pins = "mpp55";
+					marvell,function = "sata0";
+				};
+
+				sata1_pins: sata-pins-1 {
+					marvell,pins = "mpp56";
+					marvell,function = "sata1";
+				};
+
+				sata_leds: sata-leds {
+					marvell,pins = "mpp43", "mpp52", "mpp53", "mpp54";
+					marvell,function = "gpio";
+				};
+
+				btn_pins: btn-pins {
+					marvell,pins = "mpp50";
+					marvell,function = "gpio";
+				};
+			};
+
+			usb@58000 {
+				status = "okay";
+			};
+
+			phy: mdio@72004 {
+				phy0: ethernet-phy@0 {
+					/* Init ETH LEDs */
+					marvell,reg-init = <3 16 0 0x101e>;
+					reg = <0>;
+				};
+			};
+
+			sata@a8000 {
+				status = "okay";
+			};
+
+			nand-controller@d0000 {
+				status = "okay";
+
+				nand: nand@0 {
+					reg = <0>;
+					label = "pxa3xx_nand-0";
+					nand-rb = <0>;
+					marvell,nand-keep-config;
+					#marvell,nand-enable-arbiter; //optional
+					nand-on-flash-bbt;
+					nand-ecc-strength = <4>;
+					nand-ecc-step-size = <512>;
+
+					partitions {
+						compatible = "fixed-partitions";
+						#address-cells = <1>;
+						#size-cells = <1>;
+
+						partition@0 {
+							label = "U-Boot";
+							reg = <0x00000000 0x00500000>;    /*   5 MB */
+							read-only;
+						};
+
+						partition@500000 {
+							label = "kernel";
+							reg = <0x00500000 0x00500000>;    /*   5 MB */
+						};
+
+						partition@a00000 {
+							label = "uRamdisk";
+							reg = <0x00a00000 0x00500000>;    /*   5 MB */
+							read-only;
+						};
+
+						partition@f00000 {
+							label = "ubi";
+							reg = <0x00f00000 0x0b900000>;    /* 185 MB */
+						};
+
+						partition@c800000 {
+							label = "rescue fw";
+							reg = <0x0c800000 0x00f00000>;    /*  15 MB */
+							read-only;
+						};
+
+						partition@d70000 {
+							label = "config";
+							reg = <0x0d700000 0x01400000>;    /*  20 MB */
+							read-only;
+						};
+
+						partition@eb00000 {
+							label = "reserve1";
+							reg = <0x0eb00000 0x00a00000>;    /*  10 MB */
+							read-only;
+						};
+
+						partition@f500000 {
+							label = "reserve2";
+							reg = <0x0f500000 0x00a00000>;    /*  10 MB */
+							read-only;
+						};
+					};
+				};
+			};
+
+			usb3@f0000 {
+				usb-phy = <&usb3_0_phy>;
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				usb-phy = <&usb3_1_phy>;
+				status = "okay";
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&sata_leds>;
+
+		led_boot: s1red {
+			label = "red:hdd1";
+			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		};
+		s2red {
+			label = "red:hdd2";
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		};
+		s1blue {
+			label = "blue:hdd1";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata1";
+		};
+		s2blue {
+			label = "blue:hdd2";
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata2";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&btn_pins>;
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;  // Restart=0x198, Power=0x116
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+			wakeup-source;
+		};
+	};
+
+	usb3_0_phy: usb3_0_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_usb3_0_vbus>;
+	};
+
+	usb3_1_phy: usb3_1_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_usb3_1_vbus>;
+	};
+
+	reg_usb3_0_vbus: usb3-vbus0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci0_vbus_pins>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb3_1_vbus: usb3-vbus1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci1_vbus_pins>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_sata0: pwr-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		enable-active-high;
+		regulator-boot-on;
+		gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata0: v5-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_12v_sata0: v12-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_sata1: pwr-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		enable-active-high;
+		regulator-boot-on;
+		gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata1: v5-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_12v_sata1: v12-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&reg_sata1>;
+	};
+};
+
+&bm {
+	status = "okay";
+};
+
+&bm_bppi {
+	status = "okay";
+};
+
+&eth2 {
+	status = "okay";
+	phy = <&phy0>;
+	phy-mode = "sgmii";
+	buffer-manager = <&bm>;
+	bm,pool-long = <0>;
+	bm,pool-short = <1>;
+};
+
+&ahci0 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	sata-port@0 {
+		reg = <0>;
+		target-supply = <&reg_sata0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	sata-port@1 {
+		reg = <1>;
+		target-supply = <&reg_sata1>;
+		#thermal-sensor-cells = <1>;
+	};
+};

target/linux/mvebu/image/cortexa9.mk

@@ -463,6 +463,23 @@ define Device/synology_ds213j
 endef
 TARGET_DEVICES += synology_ds213j
 
+define Device/wd_cloud-ex2-ultra
+  $(Device/NAND-128K)
+  DEVICE_VENDOR := Western Digital
+  DEVICE_MODEL := MyCloud EX2 Ultra
+  DEVICE_PACKAGES += -uboot-envtools mkf2fs e2fsprogs \
+	partx-utils kmod-hwmon-drivetemp -ppp -kmod-nft-offload -dnsmasq \
+	-odhcpd-ipv6only 
+  DEVICE_DTS := armada-385-wd_cloud-ex2-ultra
+  KERNEL_SIZE := 5120k
+  KERNEL := kernel-bin | append-dtb | uImage none
+  KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
+  IMAGES += image-cfs-factory.bin uImage-factory.bin
+  IMAGE/image-cfs-factory.bin := append-ubi
+  IMAGE/uImage-factory.bin := append-kernel
+endef
+TARGET_DEVICES += wd_cloud-ex2-ultra
+
 define Device/wd_cloud-mirror-gen2
   $(Device/NAND-128K)
   DEVICE_VENDOR := Western Digital