ramips: add support for netis WF2770

netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- UART:
  - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Reviewed-by: Pawel Dembicki <[email protected]>
Signed-off-by: Sungbo Eo <[email protected]>

target/linux/ramips/dts/mt7620a_netis_wf2770.dts

@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "netis,wf2770", "ralink,mt7620a-soc";
+	model = "NETIS WF2770";
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan {
+			label = "wf2770:blue:wlan";
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		rfkill {
+			label = "rfkill";
+			gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		led-toggle {
+			label = "led-toggle";
+			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "config";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition@40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0xfb0000>;
+			};
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "i2c", "uartf";
+		function = "gpio";
+	};
+};
+
+&ethernet {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii1_pins &mdio_pins>;
+
+	mtd-mac-address = <&factory 0x4>;
+
+	port@5 {
+		status = "okay";
+		mediatek,fixed-link = <1000 1 1 1>;
+		phy-mode = "rgmii";
+	};
+
+	mdio-bus {
+		status = "okay";
+
+		ethernet-phy@0 {
+			reg = <0>;
+			phy-mode = "rgmii";
+		};
+
+		ethernet-phy@1 {
+			reg = <1>;
+			phy-mode = "rgmii";
+		};
+
+		ethernet-phy@2 {
+			reg = <2>;
+			phy-mode = "rgmii";
+		};
+
+		ethernet-phy@3 {
+			reg = <3>;
+			phy-mode = "rgmii";
+		};
+
+		ethernet-phy@4 {
+			reg = <4>;
+			phy-mode = "rgmii";
+		};
+
+		ethernet-phy@1f {
+			reg = <0x1f>;
+			phy-mode = "rgmii";
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie0 {
+	wifi@0,0 {
+		compatible = "mediatek,mt76";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x8000>;
+		ieee80211-freq-limit = <5000000 6000000>;
+	};
+};
+
+&wmac {
+	ralink,mtd-eeprom = <&factory 0x0>;
+};

target/linux/ramips/image/Makefile

@@ -100,6 +100,12 @@ define Build/mkdlinkfw-factory
 	mv [email protected] $@
 endef
 
+define Build/netis-tail
+	echo -n $(1) >> $@
+	echo -n $(UIMAGE_NAME)-yun | $(STAGING_DIR_HOST)/bin/mkhash md5 | \
+		sed 's/../\\\\x&/g' | xargs echo -ne >> $@
+endef
+
 define Build/poray-header
 	$(STAGING_DIR_HOST)/bin/mkporayfw $(1) -f $@ -o [email protected]
 	mv [email protected] $@

target/linux/ramips/image/mt7620.mk

@@ -700,6 +700,17 @@ define Device/netgear_wn3000rp-v3
 endef
 TARGET_DEVICES += netgear_wn3000rp-v3
 
+define Device/netis_wf2770
+  SOC := mt7620a
+  IMAGE_SIZE := 16064k
+  UIMAGE_NAME := WF2770_0.0.00
+  DEVICE_VENDOR := NETIS
+  DEVICE_MODEL := WF2770
+  DEVICE_PACKAGES := kmod-mt76x0e
+  KERNEL_INITRAMFS := $(KERNEL_DTB) | netis-tail WF2770 | uImage lzma
+endef
+TARGET_DEVICES += netis_wf2770
+
 define Device/nexx_wt3020-4m
   SOC := mt7620n
   BLOCKSIZE := 4k

target/linux/ramips/image/mt7621.mk

@@ -81,12 +81,6 @@ define Build/iodata-mstc-header
 	)
 endef
 
-define Build/netis-tail
-	echo -n $(1) >> $@
-	echo -n $(UIMAGE_NAME)-yun | $(STAGING_DIR_HOST)/bin/mkhash md5 | \
-		sed 's/../\\\\x&/g' | xargs echo -ne >> $@
-endef
-
 define Build/ubnt-erx-factory-image
 	if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
 		echo '21001:6' > $(1).compat; \

target/linux/ramips/mt7620/base-files/etc/board.d/02_network

@@ -170,6 +170,7 @@ ramips_setup_interfaces()
 			"1:lan:4" "2:lan:3" "4:lan:2" "5:lan:1" "0:wan" "6@eth0"
 		;;
 	linksys,e1700|\
+	netis,wf2770|\
 	ralink,mt7620a-mt7530-evb)
 		ucidef_add_switch "switch0"
 		ucidef_add_switch_attr "switch0" "enable" "false"
@@ -338,6 +339,10 @@ ramips_setup_macs()
 	linksys,e1700)
 		wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
 		;;
+	netis,wf2770)
+		wan_mac=$(mtd_get_mac_binary factory 0x2e)
+		label_mac=$wan_mac
+		;;
 	tplink,archer-c2-v1|\
 	tplink,archer-c20-v1|\
 	tplink,archer-c20i|\