ath79: add support for Netgear WNDR4500 v3

This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.

Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:

 * two USB 2.0 ports with separate LEDs
 * USB LEDs soldered to secondary pads
 * WPS and RFKILL buttons soldered to secondary pads
 * described as N900 device with 3x3:3 MIMO for 2.4GHz radio
 * power supply requirement is DC 12V 2.5A
 * vendor HW ID suffix differs in one digit
 * bigger chassis

Signed-off-by: Michal Cieslakiewicz <[email protected]>

package/boot/uboot-envtools/files/ath79

@@ -27,6 +27,7 @@ librerouter,librerouter-v1|\
 netgear,ex6400|\
 netgear,ex7300|\
 netgear,wndr4300-v2|\
+netgear,wndr4500-v3|\
 netgear,wnr1000-v2|\
 netgear,wnr2000-v3|\
 netgear,wnr2200-8m|\

target/linux/ath79/dts/qca9563_netgear_wndr4500-v3.dts

@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qca9563_netgear_wndr.dtsi"
+
+/ {
+	compatible = "netgear,wndr4500-v3", "qca,qca9563";
+	model = "Netgear WNDR4500 v3";
+};
+
+&leds {
+	usb1_green {
+		label = "netgear:green:usb1";
+		gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+		trigger-sources = <&hub_port0>;
+		linux,default-trigger = "usbport";
+	};
+
+	usb2_green {
+		label = "netgear:green:usb2";
+		gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		trigger-sources = <&hub_port1>;
+		linux,default-trigger = "usbport";
+	};
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	hub_port1: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};

target/linux/ath79/image/nand.mk

@@ -165,6 +165,17 @@ define Device/netgear_wndr4300-v2
 endef
 TARGET_DEVICES += netgear_wndr4300-v2
 
+define Device/netgear_wndr4500-v3
+  SOC := qca9563
+  DEVICE_MODEL := WNDR4500
+  DEVICE_VARIANT := v3
+  NETGEAR_KERNEL_MAGIC := 0x27051956
+  NETGEAR_BOARD_ID := WNDR4500series
+  NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012173
+  $(Device/netgear_ath79_nand)
+endef
+TARGET_DEVICES += netgear_wndr4500-v3
+
 define Device/zyxel_nbg6716
   SOC := qca9558
   DEVICE_VENDOR := ZyXEL

target/linux/ath79/nand/base-files/etc/board.d/01_leds

@@ -14,7 +14,8 @@ glinet,gl-ar300m-nor)
 	;;
 netgear,wndr3700-v4|\
 netgear,wndr4300|\
-netgear,wndr4300-v2)
+netgear,wndr4300-v2|\
+netgear,wndr4500-v3)
 	ucidef_set_led_switch "wan-amber" "WAN (amber)" "netgear:amber:wan" "switch0" "0x20"
 	;;
 esac

target/linux/ath79/nand/base-files/etc/board.d/02_network

@@ -18,7 +18,8 @@ ath79_setup_interfaces()
 		;;
 	netgear,wndr3700-v4|\
 	netgear,wndr4300|\
-	netgear,wndr4300-v2)
+	netgear,wndr4300-v2|\
+	netgear,wndr4500-v3)
 		ucidef_add_switch "switch0" \
 			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
 		;;
@@ -39,7 +40,8 @@ ath79_setup_macs()
 	case "$board" in
 	netgear,wndr3700-v4|\
 	netgear,wndr4300|\
-	netgear,wndr4300-v2)
+	netgear,wndr4300-v2|\
+	netgear,wndr4500-v3)
 		wan_mac=$(mtd_get_mac_binary caldata 0x6)
 		;;
 	zyxel,nbg6716)

target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom

@@ -11,7 +11,8 @@ case "$FIRMWARE" in
 	case $board in
 	netgear,wndr3700-v4|\
 	netgear,wndr4300|\
-	netgear,wndr4300-v2)
+	netgear,wndr4300-v2|\
+	netgear,wndr4500-v3)
 		caldata_extract "caldata" 0x1000 0x440
 		;;
 	zyxel,nbg6716)
@@ -27,7 +28,8 @@ case "$FIRMWARE" in
 	case $board in
 	netgear,wndr3700-v4|\
 	netgear,wndr4300|\
-	netgear,wndr4300-v2)
+	netgear,wndr4300-v2|\
+	netgear,wndr4500-v3)
 		caldata_extract "caldata" 0x5000 0x440
 		;;
 	*)