bcm4908: 6.12: refresh patches

Drop upstreamed patches:
* 130-arm64-dts-broadcom-bcmbca-bcm4908-set-brcm-wp-not-co.patch

All other patches automatically refreshed.

Signed-off-by: Stefan Kalscheuer <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/20169
Signed-off-by: Christian Marangi <[email protected]>

target/linux/bcm4908/patches-6.12/130-arm64-dts-broadcom-bcmbca-bcm4908-set-brcm-wp-not-co.patch

@@ -1,31 +0,0 @@
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <[email protected]>
-Date: Thu, 28 Mar 2024 10:24:34 +0100
-Subject: [PATCH] arm64: dts: broadcom: bcmbca: bcm4908: set
- brcm,wp-not-connected
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Every described BCM4908 board has WP pin not connected. This caused
-problems for drivers since day 0 but there was no property to describe
-that properly. Projects like OpenWrt were modifying Linux driver to deal
-with it.
-
-It's not clear if that is hardware limitation or just reference design
-being copied over and over but this applies to all known / supported
-BCM4908 boards. Handle it by marking WP as not connected by default.
-
-Fixes: 2961f69f151c ("arm64: dts: broadcom: add BCM4908 and Asus GT-AC5300 early DTS files")
-Signed-off-by: Rafał Miłecki <[email protected]>
----
-
---- a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
-+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
-@@ -594,6 +594,7 @@
- 			reg-names = "nand", "nand-int-base";
- 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- 			interrupt-names = "nand_ctlrdy";
-+			brcm,wp-not-connected;
- 			status = "okay";
- 
- 			nandcs: nand@0 {

target/linux/bcm4908/patches-6.12/700-net-dsa-bcm_sf2-enable-GPHY-for-switch-probing.patch

@@ -29,7 +29,7 @@ Signed-off-by: Rafał Miłecki <[email protected]>
 
 --- a/drivers/net/dsa/bcm_sf2.c
 +++ b/drivers/net/dsa/bcm_sf2.c
-@@ -1524,10 +1524,14 @@ static int bcm_sf2_sw_probe(struct platf
+@@ -1539,10 +1539,14 @@ static int bcm_sf2_sw_probe(struct platf
  	rev = reg_readl(priv, REG_PHY_REVISION);
  	priv->hw_params.gphy_rev = rev & PHY_REVISION_MASK;
  

target/linux/bcm4908/patches-6.12/701-net-dsa-bcm_sf2-keep-GPHY-enabled-on-the-BCM4908.patch

@@ -15,7 +15,7 @@ Signed-off-by: Rafał Miłecki <[email protected]>
 
 --- a/drivers/net/dsa/bcm_sf2.c
 +++ b/drivers/net/dsa/bcm_sf2.c
-@@ -1538,6 +1538,12 @@ static int bcm_sf2_sw_probe(struct platf
+@@ -1553,6 +1553,12 @@ static int bcm_sf2_sw_probe(struct platf
  		 priv->hw_params.core_rev >> 8, priv->hw_params.core_rev & 0xff,
  		 priv->irq0, priv->irq1);