lantiq: xway: rename nas0/ptm0 to dsl0

This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).

By using dsl0 as interface name as for the xrx200 we can get rid of a
few conditionals which were introduced because of the different default
TC-Layer in xway and xrx200.

Signed-off-by: Mathias Kresin <[email protected]>

package/network/config/ltq-adsl-app/Makefile

@@ -10,7 +10,7 @@ include $(INCLUDE_DIR)/kernel.mk
 
 PKG_NAME:=dsl_cpe_control_danube
 PKG_VERSION:=3.24.4.4
-PKG_RELEASE:=3
+PKG_RELEASE:=4
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.gz
 PKG_BUILD_DIR:=$(BUILD_DIR)/dsl_cpe_control-$(PKG_VERSION)
 PKG_SOURCE_URL:=http://mirror2.openwrt.org/sources/
@@ -35,7 +35,7 @@ define Package/ltq-adsl-app
   CATEGORY:=Network
   TITLE:=Lantiq DSL userland tool
   URL:=http://www.lantiq.com/
-  DEPENDS:=@(TARGET_lantiq_xway||TARGET_lantiq_xway_legacy||TARGET_lantiq_ase) +libpthread
+  DEPENDS:=@(TARGET_lantiq_xway||TARGET_lantiq_xway_legacy||TARGET_lantiq_ase) +libpthread +ip
   MENU:=1
 endef
 
@@ -76,10 +76,11 @@ CONFIGURE_ARGS += \
 TARGET_CFLAGS += -I$(LINUX_DIR)/include
 
 define Package/ltq-adsl-app/install
-	$(INSTALL_DIR) $(1)/etc/init.d $(1)/sbin $(1)/etc/hotplug.d/dsl
+	$(INSTALL_DIR) $(1)/etc/init.d $(1)/sbin $(1)/etc/hotplug.d/dsl $(1)/etc/hotplug.d/net
 	$(INSTALL_BIN) ./files/dsl_control $(1)/etc/init.d/
 	$(INSTALL_BIN) ./files/10_atm.sh $(1)/etc/hotplug.d/dsl
 	$(INSTALL_BIN) ./files/10_ptm.sh $(1)/etc/hotplug.d/dsl
+	$(INSTALL_BIN) ./files/10-adsl_rename $(1)/etc/hotplug.d/net
 	$(INSTALL_BIN) $(PKG_BUILD_DIR)/src/dsl_cpe_control $(1)/sbin
 endef
 

package/network/config/ltq-adsl-app/files/10-adsl_rename

@@ -0,0 +1,7 @@
+#!/bin/sh
+
+if [ "$ACTION" = add ]; then
+	[ "$DEVICENAME" = "nas0" ] ||[ "$DEVICENAME" = "ptm0" ] || exit
+
+	ip link set $DEVICENAME name dsl0
+fi

target/linux/lantiq/base-files/etc/board.d/01_leds

@@ -20,15 +20,12 @@ led_usb2="$(lantiq_get_dt_led usb2)"
 
 led_dsl="$(lantiq_get_dt_led dsl)"
 [ -n "$led_dsl" ] && {
-	interface="nas0"
-	lantiq_is_vdsl_system && interface="dsl0"
-
 	led_internet="$(lantiq_get_dt_led internet)"
 	if [ -n "$led_internet" ]; then
 		ucidef_set_led_default "dsl" "dsl" "$led_dsl" "0"
 		ucidef_set_led_netdev "internet" "internet" "$led_internet" "pppoe-wan"
 	else
-		ucidef_set_led_netdev "dsl" "dsl" "$led_dsl" "$interface"
+		ucidef_set_led_netdev "dsl" "dsl" "$led_dsl" "dsl0"
 	fi
 }
 

target/linux/lantiq/base-files/etc/board.d/02_network

@@ -18,7 +18,7 @@ encaps="llc"
 payload="bridged"
 lan_mac=""
 wan_mac=""
-interface_wan=""
+interface_wan="dsl0"
 
 board=$(board_name)
 
@@ -230,10 +230,8 @@ ls /lib/modules/$(uname -r)/ltq_atm* 1> /dev/null 2>&1 && \
 	ucidef_add_atm_bridge "$vpi" "$vci" "$encaps" "$payload"
 
 if lantiq_is_vdsl_system; then
-	interface_wan="dsl0"
 	ucidef_add_vdsl_modem "$annex" "$tone" "$xfer_mode"
 else
-	interface_wan="nas0"
 	ucidef_add_adsl_modem "$annex" "/lib/firmware/adsl.bin"
 fi
 

target/linux/lantiq/base-files/etc/uci-defaults/02_migrate_xdsl_iface

@@ -40,8 +40,6 @@ migrate_led_xdsl_ifname()
 	rename_xdsl_ifname system "$1" dev
 }
 
-lantiq_is_vdsl_system || exit 0
-
 config_load network
 config_foreach migrate_network_xdsl_ifname