ar71xx: add support for TP-Link Archer C58 v1

TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <[email protected]>

target/linux/ar71xx/base-files/etc/board.d/01_leds

@@ -63,6 +63,7 @@ archer-c25-v1)
 	ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04"
 	ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02"
 	;;
+archer-c58-v1|\
 archer-c59-v1|\
 archer-c60-v1)
 	ucidef_set_led_switch "lan" "LAN" "$board:green:lan" "switch0" "0x1E"

target/linux/ar71xx/base-files/etc/board.d/02_network

@@ -217,6 +217,7 @@ ar71xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
 		;;
+	archer-c58-v1|\
 	archer-c59-v1|\
 	rb-450g)
 		ucidef_set_interfaces_lan_wan "eth1.1" "eth0"

target/linux/ar71xx/base-files/etc/diag.sh

@@ -52,6 +52,7 @@ get_status_led() {
 		status_led="ap135:green:status"
 		;;
 	archer-c25-v1|\
+	archer-c58-v1|\
 	archer-c59-v1|\
 	archer-c60-v1|\
 	fritz300e|\

target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -134,6 +134,13 @@ case "$FIRMWARE" in
 		;;
 	esac
 	;;
+"ath10k/pre-cal-pci-0000:00:00.0.bin")
+	case $board in
+	archer-c58-v1)
+		ath10kcal_extract "art" 20480 12064
+		;;
+	esac
+	;;
 *)
 	exit 1
 	;;

target/linux/ar71xx/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac

@@ -0,0 +1,21 @@
+#!/bin/ash
+
+[ "$ACTION" == "add" ] || exit 0
+
+PHYNBR=${DEVPATH##*/phy}
+
+[ -n $PHYNBR ] || exit 0
+
+. /lib/ar71xx.sh
+. /lib/functions/system.sh
+
+board=$(ar71xx_board_name)
+
+case "$board" in
+	archer-c58-v1)
+		echo $(macaddr_add $(mtd_get_mac_binary mac 8)  $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress
+		;;
+	*)
+		;;
+esac
+

target/linux/ar71xx/base-files/lib/ar71xx.sh

@@ -449,6 +449,9 @@ ar71xx_board_detect() {
 	*"Archer C5")
 		name="archer-c5"
 		;;
+	*"Archer C58 v1")
+		name="archer-c58-v1"
+		;;
 	*"Archer C59 v1")
 		name="archer-c59-v1"
 		;;

target/linux/ar71xx/base-files/lib/upgrade/platform.sh

@@ -207,6 +207,7 @@ platform_check_image() {
 	ap531b0|\
 	ap90q|\
 	archer-c25-v1|\
+	archer-c58-v1|\
 	archer-c59-v1|\
 	archer-c60-v1|\
 	bullet-m|\

target/linux/ar71xx/config-4.4

@@ -52,6 +52,7 @@ CONFIG_ATH79_MACH_AP531B0=y
 CONFIG_ATH79_MACH_AP90Q=y
 CONFIG_ATH79_MACH_AP96=y
 CONFIG_ATH79_MACH_ARCHER_C25_V1=y
+CONFIG_ATH79_MACH_ARCHER_C58_V1=y
 CONFIG_ATH79_MACH_ARCHER_C59_V1=y
 CONFIG_ATH79_MACH_ARCHER_C60_V1=y
 CONFIG_ATH79_MACH_ARCHER_C7=y

target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt

@@ -1328,6 +1328,16 @@ config ATH79_MACH_ARCHER_C25_V1
 	select ATH79_DEV_M25P80
 	select ATH79_DEV_WMAC
 
+config ATH79_MACH_ARCHER_C58_V1
+	bool "TP-LINK Archer C58 v1 support"
+	select SOC_QCA956X
+	select ATH79_DEV_AP9X_PCI if PCI
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_ARCHER_C59_V1
 	bool "TP-LINK Archer C59 v1 support"
 	select SOC_QCA956X

target/linux/ar71xx/files/arch/mips/ath79/Makefile

@@ -57,6 +57,7 @@ obj-$(CONFIG_ATH79_MACH_AP531B0)		+= mach-ap531b0.o
 obj-$(CONFIG_ATH79_MACH_AP90Q)			+= mach-ap90q.o
 obj-$(CONFIG_ATH79_MACH_AP96)			+= mach-ap96.o
 obj-$(CONFIG_ATH79_MACH_ARCHER_C25_V1)		+= mach-archer-c25-v1.o
+obj-$(CONFIG_ATH79_MACH_ARCHER_C58_V1)		+= mach-archer-c59-v1.o
 obj-$(CONFIG_ATH79_MACH_ARCHER_C59_V1)		+= mach-archer-c59-v1.o
 obj-$(CONFIG_ATH79_MACH_ARCHER_C60_V1)		+= mach-archer-c60-v1.o
 obj-$(CONFIG_ATH79_MACH_ARCHER_C7)		+= mach-archer-c7.o

target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c59-v1.c

@@ -1,7 +1,7 @@
 /*
- *  TP-Link Archer C59 v1 board support
+ *  TP-Link Archer C58/C59 v1 board support
  *
- *  Copyright (C) 2016 Henryk Heisig <[email protected]>
+ *  Copyright (C) 2017 Henryk Heisig <[email protected]>
  *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
@@ -65,6 +65,44 @@
 #define ARCHER_C59_V1_WMAC_CALDATA_OFFSET	0x1000
 #define ARCHER_C59_V1_PCI_CALDATA_OFFSET	0x5000
 
+static struct gpio_led archer_c58_v1_leds_gpio[] __initdata = {
+	{
+		.name		= "archer-c58-v1:green:power",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_POWER,
+		.active_low	= 1,
+	},
+	{
+		.name		= "archer-c58-v1:green:wlan2g",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_WLAN2,
+		.active_low	= 1,
+	},
+	{
+		.name		= "archer-c58-v1:green:wlan5g",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_WLAN5,
+		.active_low	= 1,
+	},
+	{
+		.name		= "archer-c58-v1:green:lan",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_LAN,
+		.active_low	= 1,
+	},
+	{
+		.name		= "archer-c58-v1:green:wan",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_WAN_GREEN,
+		.active_low	= 1,
+	},
+	{
+		.name		= "archer-c58-v1:amber:wan",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_WAN_AMBER,
+		.active_low	= 1,
+	},
+	{
+		.name		= "archer-c58-v1:green:wps",
+		.gpio		= ARCHER_C59_74HC_GPIO_LED_WPS,
+		.active_low	= 1,
+	},
+};
+
 static struct gpio_led archer_c59_v1_leds_gpio[] __initdata = {
 	{
 		.name		= "archer-c59-v1:green:power",
@@ -177,7 +215,7 @@ static struct spi_board_info archer_c59_v1_spi_info[] = {
 	},
 };
 
-static void __init archer_c59_v1_setup(void)
+static void __init archer_c5x_v1_setup(void)
 {
 	u8 *mac = (u8 *) KSEG1ADDR(0x1f010008);
 	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
@@ -187,9 +225,6 @@ static void __init archer_c59_v1_setup(void)
 			   ARRAY_SIZE(archer_c59_v1_spi_info));
 	platform_device_register(&archer_c59_v1_spi_device);
 
-	ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c59_v1_leds_gpio),
-				archer_c59_v1_leds_gpio);
-
 	ath79_register_gpio_keys_polled(-1, ARCHER_C59_V1_KEYS_POLL_INTERVAL,
 					ARRAY_SIZE(archer_c59_v1_gpio_keys),
 					archer_c59_v1_gpio_keys);
@@ -233,5 +268,22 @@ static void __init archer_c59_v1_setup(void)
 			 "LED reset");
 }
 
+static void __init archer_c58_v1_setup(void)
+{
+	archer_c5x_v1_setup();
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c58_v1_leds_gpio),
+				archer_c58_v1_leds_gpio);
+}
+
+MIPS_MACHINE(ATH79_MACH_ARCHER_C58_V1, "ARCHER-C58-V1",
+	"TP-LINK Archer C58 v1", archer_c58_v1_setup);
+
+static void __init archer_c59_v1_setup(void)
+{
+	archer_c5x_v1_setup();
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c59_v1_leds_gpio),
+				archer_c59_v1_leds_gpio);
+}
+
 MIPS_MACHINE(ATH79_MACH_ARCHER_C59_V1, "ARCHER-C59-V1",
 	"TP-LINK Archer C59 v1", archer_c59_v1_setup);

target/linux/ar71xx/files/arch/mips/ath79/machtypes.h

@@ -42,6 +42,7 @@ enum ath79_mach_type {
 	ATH79_MACH_AP96,			/* Atheros AP96 */
 	ATH79_MACH_ARCHER_C25_V1,		/* TP-LINK Archer C25 V1 board */
 	ATH79_MACH_ARCHER_C5,			/* TP-LINK Archer C5 board */
+	ATH79_MACH_ARCHER_C58_V1,		/* TP-LINK Archer C58 V1 board */
 	ATH79_MACH_ARCHER_C59_V1,		/* TP-LINK Archer C59 V1 board */
 	ATH79_MACH_ARCHER_C60_V1,		/* TP-LINK Archer C60 V1 board */
 	ATH79_MACH_ARCHER_C7,			/* TP-LINK Archer C7 board */

target/linux/ar71xx/image/tp-link.mk

@@ -137,6 +137,17 @@ define Device/archer-c25-v1
   MTDPARTS := spi0.0:128k(factory-uboot)ro,64k(u-boot)ro,1536k(kernel),6272k(rootfs),128k(config)ro,64k(art)ro,7808k@0x30000(firmware)
 endef
 
+define Device/archer-c58-v1
+  $(Device/archer-cxx)
+  DEVICE_TITLE := TP-LINK Archer C58 v1
+  DEVICE_PACKAGES := kmod-ath10k
+  BOARDNAME := ARCHER-C58-V1
+  TPLINK_BOARD_NAME := ARCHER-C58-V1
+  DEVICE_PROFILE := ARCHERC58V1
+  IMAGE_SIZE := 7936k
+  MTDPARTS := spi0.0:64k(u-boot)ro,64k(mac)ro,1344k(kernel),6592k(rootfs),64k(tplink)ro,64k(art)ro,7936k@0x20000(firmware)
+endef
+
 define Device/archer-c59-v1
   $(Device/archer-cxx)
   DEVICE_TITLE := TP-LINK Archer C59 v1
@@ -158,7 +169,7 @@ define Device/archer-c60-v1
   IMAGE_SIZE := 7936k
   MTDPARTS := spi0.0:64k(u-boot)ro,64k(mac)ro,1344k(kernel),6592k(rootfs),64k(tplink)ro,64k(art)ro,7936k@0x20000(firmware)
 endef
-TARGET_DEVICES += archer-c25-v1 archer-c59-v1 archer-c60-v1
+TARGET_DEVICES += archer-c25-v1 archer-c58-v1 archer-c59-v1 archer-c60-v1
 
 define Device/archer-c5-v1
   $(Device/tplink-16mlzma)

target/linux/ar71xx/mikrotik/config-default

@@ -17,6 +17,7 @@
 # CONFIG_ATH79_MACH_AP90Q is not set
 # CONFIG_ATH79_MACH_AP96 is not set
 # CONFIG_ATH79_MACH_ARCHER_C25_V1 is not set
+# CONFIG_ATH79_MACH_ARCHER_C58_V1 is not set
 # CONFIG_ATH79_MACH_ARCHER_C59_V1 is not set
 # CONFIG_ATH79_MACH_ARCHER_C60_V1 is not set
 # CONFIG_ATH79_MACH_ARCHER_C7 is not set

target/linux/ar71xx/nand/config-default

@@ -17,6 +17,7 @@
 # CONFIG_ATH79_MACH_AP90Q is not set
 # CONFIG_ATH79_MACH_AP96 is not set
 # CONFIG_ATH79_MACH_ARCHER_C25_V1 is not set
+# CONFIG_ATH79_MACH_ARCHER_C58_V1 is not set
 # CONFIG_ATH79_MACH_ARCHER_C59_V1 is not set
 # CONFIG_ATH79_MACH_ARCHER_C60_V1 is not set
 # CONFIG_ATH79_MACH_ARCHER_C7 is not set

tools/firmware-utils/src/tplink-safeloader.c

@@ -341,6 +341,41 @@ static struct device_info boards[] = {
 		.last_sysupgrade_partition = "file-system",
 	},
 
+	/** Firmware layout for the C58v1 */
+	{
+		.id	= "ARCHER-C58-V1",
+		.vendor	= "",
+		.support_list =
+			"SupportList:\r\n"
+			"{product_name:Archer C58,product_ver:1.0.0,special_id:00000000}\r\n"
+			"{product_name:Archer C58,product_ver:1.0.0,special_id:45550000}\r\n"
+			"{product_name:Archer C58,product_ver:1.0.0,special_id:55530000}\r\n",
+		.support_trail = '\x00',
+		.soft_ver = "soft_ver:1.0.0\n",
+
+		.partitions = {
+			{"fs-uboot", 0x00000, 0x10000},
+			{"default-mac", 0x10000, 0x00200},
+			{"pin", 0x10200, 0x00200},
+			{"product-info", 0x10400, 0x00100},
+			{"partition-table", 0x10500, 0x00800},
+			{"soft-version", 0x11300, 0x00200},
+			{"support-list", 0x11500, 0x00100},
+			{"device-id", 0x11600, 0x00100},
+			{"profile", 0x11700, 0x03900},
+			{"default-config", 0x15000, 0x04000},
+			{"user-config", 0x19000, 0x04000},
+			{"os-image", 0x20000, 0x150000},
+			{"file-system", 0x170000, 0x678000},
+			{"certyficate", 0x7e8000, 0x08000},
+			{"radio", 0x7f0000, 0x10000},
+			{NULL, 0, 0}
+		},
+
+		.first_sysupgrade_partition = "os-image",
+		.last_sysupgrade_partition = "file-system",
+	},
+
 	/** Firmware layout for the C59v1 */
 	{
 		.id	= "ARCHER-C59-V1",