ath79: add support for tl-wr1043nd v2/v3

Signed-off-by: Lucian Cristian <[email protected]>

target/linux/ath79/base-files/etc/board.d/02_network

@@ -57,6 +57,12 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
 		;;
+	"tplink,tl-wr1043nd-v2"|\
+	"tplink,tl-wr1043nd-v3")
+		ucidef_set_interfaces_lan_wan "eth1.1" "eth0.2"
+		ucidef_add_switch "switch0" \
+			"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
+		;;
 	"netgear,wndr3800")
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \

target/linux/ath79/dts/qca9557.dtsi

@@ -14,12 +14,19 @@
 
 		cpu@0 {
 			device_type = "cpu";
-			compatible = "mips,mips24Kc";
+			compatible = "mips,mips74Kc";
 			clocks = <&pll ATH79_CLK_CPU>;
 			reg = <0>;
 		};
 	};
 
+	extosc: ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-output-names = "ref";
+		clock-frequency = <40000000>;
+	};
+
 	ahb {
 		apb {
 			ddr_ctrl: memory-controller@18000000 {
@@ -46,6 +53,28 @@
 				status = "disabled";
 			};
 
+			usb_phy0: usb-phy@18030000 {
+				compatible ="qca,qca9550-usb-phy", "qca,ar7200-usb-phy";
+
+				reset-names = "usb-phy", "usb-suspend-override";
+				resets = <&rst 4>, <&rst 3>;
+
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+
+			usb_phy1: usb-phy {
+				compatible = "qca,qca9550-usb-phy", "qca,ar7200-usb-phy";
+
+				reset-names = "usb-phy", "usb-suspend-override";
+				resets = <&rst2 4>, <&rst2 3>;
+
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+
 			gpio: gpio@18040000 {
 				compatible = "qca,ar9557-gpio",
 						"qca,ar9340-gpio";
@@ -81,10 +110,12 @@
 			pll: pll-controller@18050000 {
 				compatible = "qca,ar9557-pll",
 						"qca,qca9550-pll";
-				reg = <0x18050000 0x20>;
+				reg = <0x18050000 0x50>;
 
 				#clock-cells = <1>;
 				clock-output-names = "cpu", "ddr", "ahb";
+
+				clocks = <&extosc>;
 			};
 
 			wdt: wdt@18060008 {
@@ -98,7 +129,7 @@
 			};
 
 			rst: reset-controller@1806001c {
-				compatible = "qca,ar9557-reset",
+				compatible = "qca,qca9550-reset",
 						"qca,ar7100-reset",
 						 "simple-bus";
 				reg = <0x1806001c 0x4>;
@@ -106,18 +137,6 @@
 				#reset-cells = <1>;
 				interrupt-parent = <&cpuintc>;
 
-				intc2: interrupt-controller@2 {
-					compatible = "qcom,qca9556-intc";
-
-					interrupts = <2>;
-
-					interrupt-controller;
-					#interrupt-cells = <1>;
-
-					qcom,pending-bits = <0x1f0>,	/* pcie rc1 */
-							    <0xf>;	/* wmac */
-				};
-
 				intc3: interrupt-controller@3 {
 					compatible = "qcom,qca9556-intc";
 
@@ -126,35 +145,90 @@
 					interrupt-controller;
 					#interrupt-cells = <1>;
 
-					qcom,pending-bits = <0x1f000>,		/* pcie rc2 */
+					qcom,pending-bits = <0x1f000>,		/* pcie rc */
 							    <0x1000000>,	/* usb1 */
 							    <0x10000000>;	/* usb2 */
 				};
 			};
 
-			pcie0: pcie-controller@180c0000 {
+			rst2: reset-controller@180600c0 {
+				compatible = "qca,qca9550-reset",
+						"qca,ar7100-reset",
+						 "simple-bus";
+				reg = <0x180600c0 0x4>;
+
+				#reset-cells = <1>;
+			};
+
+			pcie: pcie-controller@18250000 {
 				compatible = "qcom,ar7240-pci";
 				#address-cells = <3>;
 				#size-cells = <2>;
 				bus-range = <0x0 0x0>;
-				reg = <0x180c0000 0x1000>, /* CRP */
-				      <0x180f0000 0x100>,  /* CTRL */
-				      <0x14000000 0x1000>; /* CFG */
+				reg = <0x18250000 0x1000>, /* CRP */
+				      <0x18280000 0x100>,  /* CTRL */
+				      <0x16000000 0x1000>; /* CFG */
 				reg-names = "crp_base", "ctrl_base", "cfg_base";
-				ranges = <0x2000000 0 0x10000000 0x10000000 0 0x04000000	/* pci memory */
+				ranges = <0x2000000 0 0x12000000 0x12000000 0 0x02000000	/* pci memory */
 					  0x1000000 0 0x00000000 0x0000000 0 0x000001>;		/* io space */
-				interrupt-parent = <&intc2>;
+				interrupt-parent = <&intc3>;
 				interrupts = <0>;
 
 				interrupt-controller;
 				#interrupt-cells = <1>;
 
 				interrupt-map-mask = <0 0 0 1>;
-				interrupt-map = <0 0 0 0 &pcie0 0>;
+				interrupt-map = <0 0 0 0 &pcie 0>;
+				status = "disabled";
+			};
+
+			wmac: wmac@18100000 {
+				compatible = "qca,qca9550-wmac";
+				reg = <0x18100000 0x10000>;
+
+				interrupt-parent = <&cpuintc>;
+				interrupts = <2>;
+
 				status = "disabled";
 			};
 		};
 
+		usb0: usb@1b000000 {
+			compatible = "generic-ehci";
+			reg = <0x1b000000 0x1fc>;
+
+			interrupt-parent = <&intc3>;
+			interrupts = <1>;
+			resets = <&rst 5>;
+			reset-names = "usb-host";
+
+			has-transaction-translator;
+			caps-offset = <0x100>;
+
+			phy-names = "usb-phy0";
+			phys = <&usb_phy0>;
+
+			status = "disabled";
+		};
+
+		usb1: usb@1b400000 {
+			compatible = "generic-ehci";
+			reg = <0x1b400000 0x1fc>;
+
+			interrupt-parent = <&intc3>;
+			interrupts = <2>;
+			resets = <&rst2 5>;
+			reset-names = "usb-host";
+
+			has-transaction-translator;
+			caps-offset = <0x100>;
+
+			phy-names = "usb-phy1";
+			phys = <&usb_phy1>;
+
+			status = "disabled";
+	};
+
 		spi: spi@1f000000 {
 			compatible = "qca,ar9557-spi", "qca,ar7100-spi";
 			reg = <0x1f000000 0x10>;

target/linux/ath79/dts/qca9558_tl-wr1043nd-v2.dts

@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9558_tl-wr1043nd.dtsi"
+
+/ {
+	compatible = "tplink,tl-wr1043nd-v2", "qca,qca9557";
+	model = "TP-Link TL-WR1043ND Version 2";
+};

target/linux/ath79/dts/qca9558_tl-wr1043nd-v3.dts

@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9558_tl-wr1043nd.dtsi"
+
+/ {
+	compatible = "tplink,tl-wr1043nd-v3", "qca,qca9557";
+	model = "TP-Link TL-WR1043ND Version 3";
+};

target/linux/ath79/dts/qca9558_tl-wr1043nd.dtsi

@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-status = &system;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		system: system {
+			label = "tp-link:green:system";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		usb {
+			label = "tp-link:green:usb";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			trigger-sources = <&hub_port0>;
+			linux,default-trigger = "usbport";
+		};
+
+		wifi_green {
+			label = "tp-link:green:wlan";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wifi_wps {
+			label = "tp-link:green:wps";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wifi {
+			label = "RFKILL button";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	gpio-export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		gpio_usb_power {
+			gpio-export,name = "tp-link:power:usb";
+			gpio-export,output = <1>;
+			gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+
+	hub_port0: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			uboot:	partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			partition@20000 {
+				label = "firmware";
+				reg = <0x020000 0x7d0000>;
+			};
+
+			art: partition@7f0000 {
+				label = "art";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		qca,ar8327-initvals = <
+		    0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+		    0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
+		    0x10 0x81000080 /* POWER_ON_STRIP */
+		    0x50 0xcc35cc35 /* LED_CTRL0 */
+		    0x54 0xca35ca35 /* LED_CTRL1 */
+		    0x58 0xc935c935 /* LED_CTRL2 */
+		    0x5c 0x03ffff00 /* LED_CTRL3 */
+		    0x7c 0x0000007e /* PORT0_STATUS */
+		    0x94 0x0000007e /* PORT6 STATUS */
+		>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	mtd-mac-address = <&uboot 0x1fc00>;
+	mtd-mac-address-increment = <1>;
+	phy-handle = <&phy0>;
+};
+
+&eth1 {
+	status = "okay";
+
+	mtd-mac-address = <&uboot 0x1fc00>;
+	phy-handle = <&phy1>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&wmac {
+	status = "okay";
+	mtd-cal-data = <&art 0x1000>;
+	mtd-mac-address = <&uboot 0x1fc00>;
+};

target/linux/ath79/image/generic-tp-link.mk

@@ -28,6 +28,26 @@ define Device/tl-wr1043nd-v1
 endef
 TARGET_DEVICES += tl-wr1043nd-v1
 
+define Device/tl-wr1043nd-v2
+  $(Device/tplink-8mlzma)
+  ATH_SOC := qca9558
+  DEVICE_TITLE := TP-LINK TL-WR1043N/ND v2
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+  TPLINK_HWID := 0x10430002
+  SUPPORTED_DEVICES := tplink,tl-wr1043nd-v2 tl-wr1043nd-v2
+endef
+TARGET_DEVICES += tl-wr1043nd-v2
+
+define Device/tl-wr1043nd-v3
+  $(Device/tplink-8mlzma)
+  ATH_SOC := qca9558
+  DEVICE_TITLE := TP-LINK TL-WR1043N/ND v3
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+  TPLINK_HWID := 0x10430003
+  SUPPORTED_DEVICES := tplink,tl-wr1043nd-v3 tl-wr1043nd-v3
+endef
+TARGET_DEVICES += tl-wr1043nd-v3
+
 define Device/tl-wr1043nd-v4
   $(Device/tplink)
   ATH_SOC := qca9563