kernel: bump 6.12 to 6.12.63

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.63

Manually rebased:
  qualcommax/patches-6.12/0113-remoteproc-qcom-Add-secure-PIL-support.patch
  qualcommax/patches-6.12/0116-remoteproc-qcom-Update-regmap-offsets-for-halt-regis.patch

Removed upstreamed:
  airoha/patches-6.12/029-14-spi-airoha-snfi-en7523-workaround-flash-damaging.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.63&id=7be679104357439ff6eab076975f5f74368acd69

Build system: x86/64
Build-tested: flogic/glinet_gl-mt6000, ramips/tplink_archer-a6-v3, x86/64-glibc
Run-tested: flogic/glinet_gl-mt6000, ramips/tplink_archer-a6-v3, x86/64-glibc

Co-authored-by: Goetz Goerisch <[email protected]>
Signed-off-by: John Audia <[email protected]>
Link: https://github.com/openwrt/openwrt/pull/21329
Signed-off-by: Robert Marko <[email protected]>

target/linux/airoha/patches-6.12/029-12-v6.19-spi-airoha-avoid-reading-flash-page-settings-from-SN.patch

@@ -158,7 +158,7 @@ Signed-off-by: Mark Brown <[email protected]>
  	.supports_op = airoha_snand_supports_op,
  	.exec_op = airoha_snand_exec_op,
  	.dirmap_create = airoha_snand_dirmap_create,
-@@ -1101,36 +1026,6 @@ static int airoha_snand_setup(struct spi
+@@ -1106,36 +1031,6 @@ static int airoha_snand_setup(struct spi
  	return 0;
  }
  
@@ -195,7 +195,7 @@ Signed-off-by: Mark Brown <[email protected]>
  static const struct regmap_config spi_ctrl_regmap_config = {
  	.name		= "ctrl",
  	.reg_bits	= 32,
-@@ -1204,7 +1099,7 @@ static int airoha_snand_probe(struct pla
+@@ -1227,7 +1122,7 @@ static int airoha_snand_probe(struct pla
  	ctrl->setup = airoha_snand_setup;
  	device_set_node(&ctrl->dev, dev_fwnode(dev));
  

target/linux/airoha/patches-6.12/029-14-v6.19-spi-airoha-snfi-en7523-workaround-flash-damaging-if-.patch

@@ -1,102 +0,0 @@
-From 061795b345aff371df8f71d54ae7c7dc8ae630d0 Mon Sep 17 00:00:00 2001
-From: Mikhail Kshevetskiy <[email protected]>
-Date: Wed, 26 Nov 2025 02:40:45 +0300
-Subject: [PATCH 14/14] spi: airoha-snfi: en7523: workaround flash damaging if
- UART_TXD was short to GND
-
-Airoha EN7523 specific bug
---------------------------
-We found that some serial console may pull TX line to GROUND during board
-boot time. Airoha uses TX line as one of its bootstrap pins. On the EN7523
-SoC this may lead to booting in RESERVED boot mode.
-
-It was found that some flashes operates incorrectly in RESERVED mode.
-Micron and Skyhigh flashes are definitely affected by the issue,
-Winbond flashes are not affected.
-
-Details:
---------
-DMA reading of odd pages on affected flashes operates incorrectly. Page
-reading offset (start of the page) on hardware level is replaced by 0x10.
-Thus results in incorrect data reading. As result OS loading becomes
-impossible.
-
-Usage of UBI make things even worse. On attaching, UBI will detects
-corruptions (because of wrong reading of odd pages) and will try to
-recover. For recovering UBI will erase and write 'damaged' blocks with
-a valid information. This will destroy all UBI data.
-
-Non-DMA reading is OK.
-
-This patch detects booting in reserved mode, turn off DMA and print big
-fat warning.
-
-It's worth noting that the boot configuration is preserved across reboots.
-Therefore, to boot normally, you should do the following:
-- disconnect the serial console from the board,
-- power cycle the board.
-
-Fixes: a403997c12019 ("spi: airoha: add SPI-NAND Flash controller driver")
-Signed-off-by: Mikhail Kshevetskiy <[email protected]>
-Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
-Reviewed-by: Andy Shevchenko <[email protected]>
-Link: https://patch.msgid.link/[email protected]
-Signed-off-by: Mark Brown <[email protected]>
----
- drivers/spi/spi-airoha-snfi.c | 25 ++++++++++++++++++++++++-
- 1 file changed, 24 insertions(+), 1 deletion(-)
-
---- a/drivers/spi/spi-airoha-snfi.c
-+++ b/drivers/spi/spi-airoha-snfi.c
-@@ -1013,6 +1013,11 @@ static const struct spi_controller_mem_o
- 	.dirmap_write = airoha_snand_dirmap_write,
- };
- 
-+static const struct spi_controller_mem_ops airoha_snand_nodma_mem_ops = {
-+	.supports_op = airoha_snand_supports_op,
-+	.exec_op = airoha_snand_exec_op,
-+};
-+
- static int airoha_snand_setup(struct spi_device *spi)
- {
- 	struct airoha_snand_ctrl *as_ctrl;
-@@ -1057,7 +1062,9 @@ static int airoha_snand_probe(struct pla
- 	struct airoha_snand_ctrl *as_ctrl;
- 	struct device *dev = &pdev->dev;
- 	struct spi_controller *ctrl;
-+	bool dma_enable = true;
- 	void __iomem *base;
-+	u32 sfc_strap;
- 	int err;
- 
- 	ctrl = devm_spi_alloc_host(dev, sizeof(*as_ctrl));
-@@ -1092,12 +1099,28 @@ static int airoha_snand_probe(struct pla
- 		return dev_err_probe(dev, PTR_ERR(as_ctrl->spi_clk),
- 				     "unable to get spi clk\n");
- 
-+	if (device_is_compatible(dev, "airoha,en7523-snand")) {
-+		err = regmap_read(as_ctrl->regmap_ctrl,
-+				  REG_SPI_CTRL_SFC_STRAP, &sfc_strap);
-+		if (err)
-+			return err;
-+
-+		if (!(sfc_strap & 0x04)) {
-+			dma_enable = false;
-+			dev_warn(dev, "Detected booting in RESERVED mode (UART_TXD was short to GND).\n");
-+			dev_warn(dev, "This mode is known for incorrect DMA reading of some flashes.\n");
-+			dev_warn(dev, "Much slower PIO mode will be used to prevent flash data damage.\n");
-+			dev_warn(dev, "Unplug UART cable and power cycle board to get full performance.\n");
-+		}
-+	}
-+
- 	err = dma_set_mask(as_ctrl->dev, DMA_BIT_MASK(32));
- 	if (err)
- 		return err;
- 
- 	ctrl->num_chipselect = 2;
--	ctrl->mem_ops = &airoha_snand_mem_ops;
-+	ctrl->mem_ops = dma_enable ? &airoha_snand_mem_ops
-+				   : &airoha_snand_nodma_mem_ops;
- 	ctrl->bits_per_word_mask = SPI_BPW_MASK(8);
- 	ctrl->mode_bits = SPI_RX_DUAL;
- 	ctrl->setup = airoha_snand_setup;

target/linux/bcm27xx/patches-6.12/950-0073-ASoC-Add-support-for-all-the-downstream-rpi-sound-ca.patch

@@ -15556,7 +15556,7 @@ Signed-off-by: j-schambacher <[email protected]>
  	imply SND_SOC_MAX98088
  	imply SND_SOC_MAX98090
  	imply SND_SOC_MAX98095
-@@ -175,6 +177,7 @@ config SND_SOC_ALL_CODECS
+@@ -176,6 +178,7 @@ config SND_SOC_ALL_CODECS
  	imply SND_SOC_PCM179X_SPI
  	imply SND_SOC_PCM186X_I2C
  	imply SND_SOC_PCM186X_SPI
@@ -15564,7 +15564,7 @@ Signed-off-by: j-schambacher <[email protected]>
  	imply SND_SOC_PCM3008
  	imply SND_SOC_PCM3060_I2C
  	imply SND_SOC_PCM3060_SPI
-@@ -267,6 +270,7 @@ config SND_SOC_ALL_CODECS
+@@ -268,6 +271,7 @@ config SND_SOC_ALL_CODECS
  	imply SND_SOC_TLV320ADCX140
  	imply SND_SOC_TLV320AIC23_I2C
  	imply SND_SOC_TLV320AIC23_SPI
@@ -15572,7 +15572,7 @@ Signed-off-by: j-schambacher <[email protected]>
  	imply SND_SOC_TLV320AIC26
  	imply SND_SOC_TLV320AIC31XX
  	imply SND_SOC_TLV320AIC32X4_I2C
-@@ -424,12 +428,12 @@ config SND_SOC_AD193X
+@@ -425,12 +429,12 @@ config SND_SOC_AD193X
  	tristate
  
  config SND_SOC_AD193X_SPI
@@ -15587,7 +15587,7 @@ Signed-off-by: j-schambacher <[email protected]>
  	depends on I2C
  	select SND_SOC_AD193X
  
-@@ -1229,6 +1233,13 @@ config SND_SOC_LOCHNAGAR_SC
+@@ -1230,6 +1234,13 @@ config SND_SOC_LOCHNAGAR_SC
  	  This driver support the sound card functionality of the Cirrus
  	  Logic Lochnagar audio development board.
  
@@ -15601,7 +15601,7 @@ Signed-off-by: j-schambacher <[email protected]>
  config SND_SOC_MADERA
  	tristate
  	default y if SND_SOC_CS47L15=y
-@@ -1638,6 +1649,10 @@ config SND_SOC_RT5616
+@@ -1639,6 +1650,10 @@ config SND_SOC_RT5616
  	tristate "Realtek RT5616 CODEC"
  	depends on I2C
  
@@ -15612,7 +15612,7 @@ Signed-off-by: j-schambacher <[email protected]>
  config SND_SOC_RT5631
  	tristate "Realtek ALC5631/RT5631 CODEC"
  	depends on I2C
-@@ -1995,6 +2010,9 @@ config SND_SOC_TFA9879
+@@ -1996,6 +2011,9 @@ config SND_SOC_TFA9879
  	tristate "NXP Semiconductors TFA9879 amplifier"
  	depends on I2C
  
@@ -15622,7 +15622,7 @@ Signed-off-by: j-schambacher <[email protected]>
  config SND_SOC_TFA989X
  	tristate "NXP/Goodix TFA989X (TFA1) amplifiers"
  	depends on I2C
-@@ -2596,4 +2614,8 @@ config SND_SOC_LPASS_TX_MACRO
+@@ -2601,4 +2619,8 @@ config SND_SOC_LPASS_TX_MACRO
  	select SND_SOC_LPASS_MACRO_COMMON
  	tristate "Qualcomm TX Macro in LPASS(Low Power Audio SubSystem)"
  
@@ -15633,7 +15633,7 @@ Signed-off-by: j-schambacher <[email protected]>
  endmenu
 --- a/sound/soc/codecs/Makefile
 +++ b/sound/soc/codecs/Makefile
-@@ -820,3 +820,12 @@ obj-$(CONFIG_SND_SOC_LPASS_TX_MACRO)	+=
+@@ -822,3 +822,12 @@ obj-$(CONFIG_SND_SOC_LPASS_TX_MACRO)	+=
  
  # Mux
  obj-$(CONFIG_SND_SOC_SIMPLE_MUX)	+= snd-soc-simple-mux.o

target/linux/bcm27xx/patches-6.12/950-0348-usb-dwc3-Set-DMA-and-coherent-masks-early.patch

@@ -351,7 +351,7 @@ Signed-off-by: Jonathan Bell <[email protected]>
  
 --- a/drivers/usb/dwc3/host.c
 +++ b/drivers/usb/dwc3/host.c
-@@ -126,10 +126,12 @@ out:
+@@ -129,10 +129,12 @@ out:
  
  int dwc3_host_init(struct dwc3 *dwc)
  {
@@ -364,7 +364,7 @@ Signed-off-by: Jonathan Bell <[email protected]>
  
  	/*
  	 * Some platforms need to power off all Root hub ports immediately after DWC3 set to host
-@@ -141,7 +143,12 @@ int dwc3_host_init(struct dwc3 *dwc)
+@@ -144,7 +146,12 @@ int dwc3_host_init(struct dwc3 *dwc)
  	if (irq < 0)
  		return irq;
  

target/linux/bcm27xx/patches-6.12/950-0380-irqchip-irq-brcmstb-l2-Add-config-for-2711-controlle.patch

@@ -52,7 +52,7 @@ Signed-off-by: Dom Cobley <[email protected]>
  /* L2 intc private data structure */
  struct brcmstb_l2_intc_data {
  	struct irq_domain *domain;
-@@ -299,11 +309,18 @@ static int __init brcmstb_l2_lvl_intc_of
+@@ -295,11 +305,18 @@ static int brcmstb_l2_lvl_intc_of_init(s
  	return brcmstb_l2_intc_of_init(np, parent, &l2_lvl_intc_init);
  }
  

target/linux/generic/hack-6.12/902-debloat_proc.patch

@@ -409,7 +409,7 @@ Signed-off-by: Felix Fietkau <[email protected]>
  
 --- a/net/ipv4/inet_timewait_sock.c
 +++ b/net/ipv4/inet_timewait_sock.c
-@@ -296,7 +296,7 @@ void __inet_twsk_schedule(struct inet_ti
+@@ -285,7 +285,7 @@ void __inet_twsk_schedule(struct inet_ti
  	 */
  
  	if (!rearm) {

target/linux/generic/kernel-6.12

@@ -1,2 +1,2 @@
-LINUX_VERSION-6.12 = .62
-LINUX_KERNEL_HASH-6.12.62 = 13e2c685ac8fab5dd992dd105732554dae514aef350c2a8c7418e7b74eb62c13
+LINUX_VERSION-6.12 = .63
+LINUX_KERNEL_HASH-6.12.63 = 9502c5ffe4b894383c97abfccf74430a84732f04ee476b9c0d87635b29df7db3

target/linux/generic/pending-6.12/700-netfilter-nft_flow_offload-handle-netdevice-events-f.patch

@@ -55,7 +55,7 @@ Signed-off-by: Pablo Neira Ayuso <[email protected]>
  }
 --- a/net/netfilter/nft_flow_offload.c
 +++ b/net/netfilter/nft_flow_offload.c
-@@ -487,47 +487,14 @@ static struct nft_expr_type nft_flow_off
+@@ -494,47 +494,14 @@ static struct nft_expr_type nft_flow_off
  	.owner		= THIS_MODULE,
  };
  

target/linux/qualcommax/patches-6.12/0113-remoteproc-qcom-Add-secure-PIL-support.patch

@@ -25,7 +25,7 @@ Signed-off-by: Nikhil Prakash V <[email protected]>
 @@ -86,6 +87,9 @@
  #define TCSR_WCSS_CLK_ENABLE	0x14
  
- #define MAX_HALT_REG		3
+ #define MAX_HALT_REG		4
 +
 +#define WCNSS_PAS_ID		6
 +

target/linux/qualcommax/patches-6.12/0116-remoteproc-qcom-Update-regmap-offsets-for-halt-regis.patch

@@ -13,15 +13,6 @@ Signed-off-by: Sricharan R <[email protected]>
 
 --- a/drivers/remoteproc/qcom_q6v5_wcss.c
 +++ b/drivers/remoteproc/qcom_q6v5_wcss.c
-@@ -86,7 +86,7 @@
- #define TCSR_WCSS_CLK_MASK	0x1F
- #define TCSR_WCSS_CLK_ENABLE	0x14
- 
--#define MAX_HALT_REG		3
-+#define MAX_HALT_REG		4
- 
- #define WCNSS_PAS_ID		6
- 
 @@ -155,6 +155,7 @@ struct wcss_data {
  	u32 version;
  	bool aon_reset_required;
@@ -48,19 +39,6 @@ Signed-off-by: Sricharan R <[email protected]>
  	}
  
  	return 0;
-@@ -929,9 +933,9 @@ static int q6v5_wcss_init_mmio(struct q6
- 		return -EINVAL;
- 	}
- 
--	wcss->halt_q6 = halt_reg[0];
--	wcss->halt_wcss = halt_reg[1];
--	wcss->halt_nc = halt_reg[2];
-+	wcss->halt_q6 = halt_reg[1];
-+	wcss->halt_wcss = halt_reg[2];
-+	wcss->halt_nc = halt_reg[3];
- 
- 	return 0;
- }
 @@ -1173,6 +1177,7 @@ static const struct wcss_data wcss_ipq80
  	.crash_reason_smem = WCSS_CRASH_REASON,
  	.aon_reset_required = true,

target/linux/ramips/patches-6.12/850-awake-rt305x-dwc2-controller.patch

@@ -1,6 +1,6 @@
 --- a/drivers/usb/dwc2/platform.c
 +++ b/drivers/usb/dwc2/platform.c
-@@ -481,6 +481,12 @@ static int dwc2_driver_probe(struct plat
+@@ -484,6 +484,12 @@ static int dwc2_driver_probe(struct plat
  	if (retval)
  		return retval;
  

target/linux/realtek/patches-6.12/318-add-rtl83xx-clk-support.patch

@@ -23,7 +23,7 @@ Submitted-by: Markus Stockhausen <[email protected]>
  source "drivers/clk/rockchip/Kconfig"
 --- a/drivers/clk/Makefile
 +++ b/drivers/clk/Makefile
-@@ -123,6 +123,7 @@ obj-$(CONFIG_COMMON_CLK_PISTACHIO)	+= pi
+@@ -122,6 +122,7 @@ obj-$(CONFIG_COMMON_CLK_PISTACHIO)	+= pi
  obj-$(CONFIG_COMMON_CLK_PXA)		+= pxa/
  obj-$(CONFIG_COMMON_CLK_QCOM)		+= qcom/
  obj-y					+= ralink/

target/linux/rockchip/patches-6.12/001-01-v6.13-arm64-dts-rockchip-Split-up-RK3588-s-PCIe-pinctrls.patch

@@ -422,7 +422,7 @@ Signed-off-by: Heiko Stuebner <[email protected]>
  		};
 --- a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
 +++ b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
-@@ -310,7 +310,7 @@
+@@ -311,7 +311,7 @@
  };
  
  &pcie2x1l2 {
@@ -431,7 +431,7 @@ Signed-off-by: Heiko Stuebner <[email protected]>
  	pinctrl-names = "default";
  	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
  	vpcie3v3-supply = <&vcc3v3_wf>;
-@@ -328,6 +328,10 @@
+@@ -329,6 +329,10 @@
  		pow_en: pow-en {
  			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
  		};

target/linux/rockchip/patches-6.12/002-02-v6.13-arm64-dts-rockchip-Enable-HDMI0-on-rock-5a.patch

@@ -37,7 +37,7 @@ Signed-off-by: Heiko Stuebner <[email protected]>
  	leds {
  		compatible = "gpio-leds";
  		pinctrl-names = "default";
-@@ -301,6 +313,31 @@
+@@ -302,6 +314,31 @@
  	status = "okay";
  };
  
@@ -69,7 +69,7 @@ Signed-off-by: Heiko Stuebner <[email protected]>
  &mdio1 {
  	rgmii_phy1: ethernet-phy@1 {
  		/* RTL8211F */
-@@ -793,3 +830,18 @@
+@@ -794,3 +831,18 @@
  &usb_host2_xhci {
  	status = "okay";
  };

target/linux/rockchip/patches-6.12/002-05-v6.15-arm64-dts-rockchip-Fix-label-name-of-hdptxphy-for-RK.patch

@@ -15,7 +15,7 @@ Signed-off-by: Heiko Stuebner <[email protected]>
 
 --- a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
 +++ b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
-@@ -334,7 +334,7 @@
+@@ -335,7 +335,7 @@
  	};
  };
  

target/linux/rockchip/patches-6.12/002-06-v6.15-arm64-dts-rockchip-Add-GPU-power-domain-regulator-de.patch

@@ -35,7 +35,7 @@ Signed-off-by: Heiko Stuebner <[email protected]>
 
 --- a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
 +++ b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
-@@ -359,6 +359,10 @@
+@@ -360,6 +360,10 @@
  	status = "okay";
  };
  

target/linux/rockchip/patches-6.12/116-arm64-dts-rockchip-Update-LED-properties-for-Radxa-Ro.patch

@@ -44,7 +44,7 @@ Signed-off-by: Tianling Shen <[email protected]>
  		};
  	};
  
-@@ -365,8 +375,9 @@
+@@ -366,8 +376,9 @@
  
  &pinctrl {
  	leds {

target/linux/siflower/patches-6.12/005-clk-add-drivers-for-siflower-socs.patch

@@ -20,7 +20,7 @@ Signed-off-by: Chuanhong Guo <[email protected]>
  source "drivers/clk/sprd/Kconfig"
 --- a/drivers/clk/Makefile
 +++ b/drivers/clk/Makefile
-@@ -127,6 +127,7 @@ obj-y					+= renesas/
+@@ -126,6 +126,7 @@ obj-y					+= renesas/
  obj-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip/
  obj-$(CONFIG_COMMON_CLK_SAMSUNG)	+= samsung/
  obj-$(CONFIG_CLK_SIFIVE)		+= sifive/