kirkwood: move led triggers to dts

This patch moves led trigger settings from 01_leds file to dts.

Now "linux,default-trigger" property is used.

Tested-by: Alberto Bursi <[email protected]> [nsa310,nsa325]
Signed-off-by: Pawel Dembicki <[email protected]>

target/linux/kirkwood/base-files/etc/board.d/01_leds

@@ -16,16 +16,6 @@ case "$board" in
 "linksys,viper")
 	ucidef_set_led_default "pulse" "pulse" "viper:white:pulse" "1"
 	;;
-"zyxel,nsa310b")
-	ucidef_set_led_usbhost "usb" "USB" "nsa310:green:usb"
-	ucidef_set_led_ataport "hdd" "HDD" "nsa310:green:hdd" "1"
-	ucidef_set_led_ataport "esata" "eSata" "nsa310:green:esata" "2"
-	;;
-"zyxel,nsa325")
-	ucidef_set_led_usbhost "usb" "USB" "nsa325:green:usb"
-	ucidef_set_led_ataport "hdd1" "HDD1" "nsa325:green:hdd1" "1"
-	ucidef_set_led_ataport "hdd2" "HDD2" "nsa325:green:hdd2" "2"
-	;;
 esac
 
 board_config_flush

target/linux/kirkwood/files-5.4/arch/arm/boot/dts/kirkwood-nsa310b.dts

@@ -101,6 +101,7 @@
 		green-hdd {
 			label = "nsa310:green:hdd";
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata1";
 		};
 
 		red-hdd {
@@ -111,6 +112,7 @@
 		green-esata {
 			label = "nsa310:green:esata";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata2";
 		};
 
 		red-esata {
@@ -121,6 +123,7 @@
 		green-usb {
 			label = "nsa310:green:usb";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-host";
 		};
 
 		red-usb {

target/linux/kirkwood/patches-5.4/107-03-nsa325.patch

@@ -14,7 +14,7 @@
  	memory {
  		device_type = "memory";
  		reg = <0x00000000 0x20000000>;
-@@ -162,11 +169,12 @@
+@@ -162,17 +169,19 @@
  			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
  		pinctrl-names = "default";
  
@@ -29,3 +29,26 @@
  			label = "nsa325:orange:sys";
  			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
  		};
+ 		green-hdd1 {
+ 			label = "nsa325:green:hdd1";
+ 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata1";
+ 		};
+ 		red-hdd1 {
+ 			label = "nsa325:red:hdd1";
+@@ -181,6 +190,7 @@
+ 		green-hdd2 {
+ 			label = "nsa325:green:hdd2";
+ 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata2";
+ 		};
+ 		red-hdd2 {
+ 			label = "nsa325:red:hdd2";
+@@ -189,6 +199,7 @@
+ 		green-usb {
+ 			label = "nsa325:green:usb";
+ 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "usb-host";
+ 		};
+ 		green-copy {
+ 			label = "nsa325:green:copy";