lantiq: Add Support for Fritz!Box 7360 SL

Signed-off-by: Sebastian Ortwein <[email protected]>
Tested-by: Guido Lipke <[email protected]>

target/linux/lantiq/base-files/etc/board.d/02_network

@@ -76,6 +76,11 @@ DGN3500*)
 		"3:lan:1" "2:lan:2" "1:lan:3" "0:lan:4" "5t@eth0"
 	;;
 
+FRITZ7360SL)
+	ucidef_add_switch "switch0" \
+		"4:lan:1" "2:lan:2" "0:lan:3" "1:lan:4" "6t@eth0"
+	;;
+
 GR7000)
 	ucidef_set_interface_wan "eth0"
 	;;

target/linux/lantiq/dts/FRITZ7360SL.dts

@@ -0,0 +1,217 @@
+/dts-v1/;
+
+/include/ "vr9.dtsi"
+
+/ {
+	model = "FRITZ7360SL - 1&1 HomeServer";
+
+	chosen {
+		bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+
+		leds {
+			boot = &power_green;
+			failsafe = &power_red;
+			running = &power_green;
+
+			internet = &info_green;
+			dsl = &power_green;
+			wifi = &wifi;
+		};
+	};
+
+	memory@0 {
+		reg = <0x0 0x8000000>;
+	};
+
+	fpi@10000000 {
+		localbus@0 {
+			nor-boot@0 {
+				compatible = "lantiq,nor";
+				bank-width = <2>;
+				reg = <0 0x0 0x1000000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					urlader: partition@0 {
+						label = "urlader";
+						reg = <0x00000 0x20000>;
+						read-only;
+					};
+
+					partition@20000 {
+						label = "firmware";
+						reg = <0x20000 0xf60000>;
+					};
+
+					partition@f80000 {
+						label = "tffs (1)";
+						reg = <0xf80000 0x40000>;
+						read-only;
+					};
+
+					partition@fc0000 {
+						label = "tffs (2)";
+						reg = <0xfc0000 0x40000>;
+						read-only;
+					};
+				};
+			};
+		};
+
+		gpio: pinmux@E100B10 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				mdio {
+					lantiq,groups = "mdio";
+					lantiq,function = "mdio";
+				};
+				phy-rst {
+					lantiq,pins = "io37", "io44";
+					lantiq,pull = <2>;
+					lantiq,open-drain;
+					lantiq,output = <1>;
+				};
+				pcie-rst {
+					lantiq,pins = "io38";
+					lantiq,pull = <0>;
+					lantiq,output = <1>;
+				};
+			};
+		};
+
+		ifxhcd@E101000 {
+			status = "okay";
+			lantiq,portmask = <0x3>;
+		};
+
+		ifxhcd@E106000 {
+			status = "okay";
+		};
+	};
+
+	ath9k_eep {
+		compatible = "ath9k,eeprom";
+		ath,eep-flash = <&urlader 0x985>;
+		ath,eep-endian;
+		ath,eep-swap;
+		ath,pci-slot = <0>;
+	};
+
+	gphy-xrx200 {
+		compatible = "lantiq,phy-xrx200";
+		firmware = "lantiq/vr9_phy11g_a2x.bin";
+		phys = [ 00 01 ];
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+		dect {
+			label = "power";
+			gpios = <&gpio 1 0>;
+			linux,code = <0x102>;
+		};
+		wifi {
+			label = "wifi";
+			gpios = <&gpio 29 0>;
+			linux,code = <0x101>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power_green: power {
+			label = "fritz7360sl:green:power";
+			gpios = <&gpio 32 1>;
+			default-state = "keep";
+		};
+		power_red: power2 {
+			label = "fritz7360sl:red:power";
+			gpios = <&gpio 33 1>;
+		};
+		info_red {
+			label = "fritz7360sl:red:info";
+			gpios = <&gpio 34 1>;
+		};
+		info_green: info_green {
+			label = "fritz7360sl:green:info";
+			gpios = <&gpio 47 1>;
+		};
+		wifi: wifi {
+			label = "fritz7360sl:green:wlan";
+			gpios = <&gpio 36 1>;
+		};
+		dect {
+			label = "fritz7360sl:green:dect";
+			gpios = <&gpio 35 1>;
+		};
+	};
+};
+
+&eth0 {
+	lan: interface@0 {
+		compatible = "lantiq,xrx200-pdi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+		mac-address = [ 00 11 22 33 44 55 ];
+		lantiq,switch;
+
+		ethernet@0 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <0>;
+			phy-mode = "rmii";
+			phy-handle = <&phy0>;
+			// gpios = <&gpio 37 1>;
+		};
+		ethernet@1 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <1>;
+			phy-mode = "rmii";
+			phy-handle = <&phy1>;
+			// gpios = <&gpio 44 1>;
+		};
+		ethernet@2 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <2>;
+			phy-mode = "gmii";
+			phy-handle = <&phy11>;
+		};
+		ethernet@3 {
+			compatible = "lantiq,xrx200-pdi-port";
+			reg = <4>;
+			phy-mode = "gmii";
+			phy-handle = <&phy13>;
+		};
+	};
+
+	mdio@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "lantiq,xrx200-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0x00>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+		phy1: ethernet-phy@1 {
+			reg = <0x01>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+		phy11: ethernet-phy@11 {
+			reg = <0x11>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+		phy13: ethernet-phy@13 {
+			reg = <0x13>;
+			compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};

target/linux/lantiq/image/Makefile

@@ -642,6 +642,9 @@ FRITZ3370_UBI_OPTS:="-m 2048 -p 128KiB -s 512"
 Image/BuildKernel/Profile/FRITZ3370=$(call Image/BuildKernelEVA/Template,FRITZ3370)
 Image/Build/Profile/FRITZ3370=$(call Image/BuildEVA/$(1),$(1),FRITZ3370)
 
+Image/BuildKernel/Profile/FRITZ7360SL=$(call Image/BuildKernelEVA/Template,FRITZ7360SL)
+Image/Build/Profile/FRITZ7360SL=$(call Image/BuildEVA/$(1),$(1),FRITZ7360SL)
+
 Image/BuildKernel/Profile/VG3503J=$(call Image/BuildKernelLoader/Template,VG3503J)
 Image/Build/Profile/VG3503J=$(call Image/BuildLoader/$(1),$(1),VG3503J)
 

target/linux/lantiq/xrx200/config-default

@@ -1,5 +1,6 @@
 CONFIG_ADM6996_PHY=y
 CONFIG_AR8216_PHY=y
+CONFIG_AT803X_PHY=y
 CONFIG_CPU_MIPSR2_IRQ_EI=y
 CONFIG_CPU_MIPSR2_IRQ_VI=y
 CONFIG_CPU_RMAP=y

target/linux/lantiq/xrx200/profiles/avm.mk

@@ -4,3 +4,10 @@ define Profile/FRITZ3370
 endef
 
 $(eval $(call Profile,FRITZ3370))
+
+define Profile/FRITZ7360SL
+  NAME:=1&1 HomeServer - FRITZ7360SL
+  PACKAGES:=kmod-ath9k wpad-mini kmod-usb-dwc2
+endef
+
+$(eval $(call Profile,FRITZ7360SL))