ath79: add support for NEC Aterm WG800HP

NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <[email protected]>

target/linux/ath79/base-files/etc/board.d/02_network

@@ -89,6 +89,10 @@ ath79_setup_interfaces()
 	glinet,gl-x750)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		;;
+	nec,wg800hp)
+		ucidef_add_switch "switch0" \
+			"0@eth0" "2:lan" "3:lan" "4:lan" "1:wan"
+		;;
 	netgear,wndr3700|\
 	netgear,wndr3700v2|\
 	netgear,wndr3800)
@@ -238,6 +242,10 @@ ath79_setup_macs()
 		lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
 		wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
 		;;
+	nec,wg800hp)
+		lan_mac=$(mtd_get_mac_text board_data 640)
+		wan_mac=$(mtd_get_mac_text board_data 1152)
+		;;
 	netgear,wndr3700|\
 	netgear,wndr3700v2|\
 	netgear,wndr3800)

target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom

@@ -111,6 +111,10 @@ case "$FIRMWARE" in
 		ath9k_eeprom_extract "art" 4096 1088
 		ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
 		;;
+	nec,wg800hp)
+		ath9k_eeprom_extract "art" 4096 1088
+		ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2
+		;;
 	*)
 		ath9k_eeprom_die "board $board is not supported yet"
 		;;

target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -96,6 +96,10 @@ case "$FIRMWARE" in
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
 		;;
+	nec,wg800hp)
+		ath10kcal_extract "art" 20480 2116
+		ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
+		;;
 	ocedo,koala)
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(mtd_get_mac_binary art 12)

target/linux/ath79/dts/qca9563_nec_wg800hp.dts

@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	model = "NEC Aterm WG800HP";
+	compatible = "nec,wg800hp", "qca,qca9563";
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-boot = &power_green;
+		led-failsafe = &power_red;
+		led-running = &power_green;
+		led-upgrade = &power_green;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&jtag_disable_pins>;
+
+		wlan2g_red {
+			label = "wg800hp:red:wlan2g";
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+		};
+
+		active_red {
+			label = "wg800hp:red:active";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		active_green {
+			label = "wg800hp:green:active";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		power_red: power_red {
+			label = "wg800hp:red:power";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		power_green: power_green {
+			label = "wg800hp:green:power";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		wlan5g_red {
+			label = "wg800hp:red:wlan5g";
+			gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g_green {
+			label = "wg800hp:green:wlan5g";
+			gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan2g_green {
+			label = "wg800hp:green:wlan2g";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		br {
+			label = "br";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+			debounce-interval = <60>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+				read-only;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0x6f0000>;
+			};
+
+			partition@740000 {
+				label = "user_data";
+				reg = <0x740000 0x0a0000>;
+				read-only;
+			};
+
+			partition@7e0000 {
+				label = "board_data";
+				reg = <0x7e0000 0x010000>;
+				read-only;
+			};
+
+			art: partition@7f0000 {
+				label = "art";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+
+		qca,ar8327-initvals = <
+			0x04 0x00000080 /* PORT0 PAD MODE CTRL */
+			0x50 0xcc35cc35 /* LED_CTRL0 */
+			0x54 0xca35ca35 /* LED_CTRL1 */
+			0x58 0xc935c935 /* LED_CTRL2 */
+			0x5c 0x03ffff00 /* LED_CTRL3 */
+			0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&wmac {
+	status = "okay";
+	qca,no-eeprom;
+};

target/linux/ath79/image/generic.mk

@@ -43,6 +43,16 @@ define Build/elecom-header
 
 endef
 
+define Build/nec-fw
+  ( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
+  ( \
+    echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
+    echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
+    dd if=$@; \
+  ) > [email protected]
+  mv [email protected] $@
+endef
+
 define Device/avm_fritz300e
   ATH_SOC := ar7242
   DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
@@ -262,6 +272,19 @@ define Device/iodata_wn-ag300dgr
 endef
 TARGET_DEVICES += iodata_wn-ag300dgr
 
+define Device/nec_wg800hp
+  ATH_SOC := qca9563
+  DEVICE_TITLE := NEC Aterm WG800HP
+  IMAGE_SIZE := 7104k
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+    append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
+    xor-image -p 6A57190601121E4C004C1E1201061957 -x | \
+    nec-fw LASER_ATERM
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct-htt
+endef
+TARGET_DEVICES += nec_wg800hp
+
 define Device/ocedo_koala
   ATH_SOC := qca9558
   DEVICE_TITLE := OCEDO Koala