ath79: re-add accidentally dropped patch to kernel 5.4

Patch 0061-tty-serial-ar933x-uart-rs485-gpio.patch wasn't included
when adding support for kernel 5.4. Re-add it and refresh patches.

Fixes: 53ab9865c2 ("ath79: add support for kernel 5.4")
Signed-off-by: Daniel Golle <[email protected]>

target/linux/ath79/patches-5.4/0036-GPIO-add-named-gpio-exports.patch

@@ -22,8 +22,8 @@ Signed-off-by: John Crispin <[email protected]>
  
  #include "gpiolib.h"
  #include "gpiolib-of.h"
-@@ -895,3 +897,68 @@ void of_gpiochip_remove(struct gpio_chip
- 	gpiochip_remove_pin_ranges(chip);
+@@ -915,3 +917,68 @@ void of_gpiochip_remove(struct gpio_chip
+ {
  	of_node_put(chip->of_node);
  }
 +
@@ -141,7 +141,7 @@ Signed-off-by: John Crispin <[email protected]>
  {
 --- a/include/linux/gpio/consumer.h
 +++ b/include/linux/gpio/consumer.h
-@@ -661,6 +661,7 @@ static inline void devm_acpi_dev_remove_
+@@ -668,6 +668,7 @@ static inline void devm_acpi_dev_remove_
  
  #if IS_ENABLED(CONFIG_GPIOLIB) && IS_ENABLED(CONFIG_GPIO_SYSFS)
  
@@ -149,7 +149,7 @@ Signed-off-by: John Crispin <[email protected]>
  int gpiod_export(struct gpio_desc *desc, bool direction_may_change);
  int gpiod_export_link(struct device *dev, const char *name,
  		      struct gpio_desc *desc);
-@@ -668,6 +669,13 @@ void gpiod_unexport(struct gpio_desc *de
+@@ -675,6 +676,13 @@ void gpiod_unexport(struct gpio_desc *de
  
  #else  /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */
  

target/linux/ath79/patches-5.4/0061-tty-serial-ar933x-uart-rs485-gpio.patch

@@ -0,0 +1,267 @@
+From patchwork Fri Feb 21 21:23:31 2020
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+X-Patchwork-Submitter: Daniel Golle <[email protected]>
+X-Patchwork-Id: 1198835
+Date: Fri, 21 Feb 2020 22:23:31 +0100
+From: Daniel Golle <[email protected]>
+To: [email protected], [email protected]
+Cc: Greg Kroah-Hartman <[email protected]>,
+ Jiri Slaby <[email protected]>, Petr =?utf-8?q?=C5=A0tetiar?= <[email protected]>,
+ Chuanhong Guo <[email protected]>, Piotr Dymacz <[email protected]>
+Subject: [PATCH v2] serial: ar933x_uart: add RS485 support
+Message-ID: <[email protected]>
+MIME-Version: 1.0
+Content-Disposition: inline
+Sender: [email protected]
+Precedence: bulk
+List-ID: <linux-kernel.vger.kernel.org>
+X-Mailing-List: [email protected]
+
+Emulate half-duplex operation and use mctrl_gpio to add support for
+RS485 tranceiver with transmit/receive switch hooked to RTS GPIO line.
+This is needed to make use of the RS485 port found on Teltonika RUT955.
+
+Signed-off-by: Daniel Golle <[email protected]>
+---
+v2: use bool to indicate ongoing half-duplex send, use it afterwards
+    to decide whether we've just been in a send operation.
+
+ drivers/tty/serial/Kconfig       |   1 +
+ drivers/tty/serial/ar933x_uart.c | 113 +++++++++++++++++++++++++++++--
+ 2 files changed, 108 insertions(+), 6 deletions(-)
+
+--- a/drivers/tty/serial/Kconfig
++++ b/drivers/tty/serial/Kconfig
+@@ -1279,6 +1279,7 @@ config SERIAL_AR933X
+ 	tristate "AR933X serial port support"
+ 	depends on HAVE_CLK && ATH79
+ 	select SERIAL_CORE
++	select SERIAL_MCTRL_GPIO if GPIOLIB
+ 	help
+ 	  If you have an Atheros AR933X SOC based board and want to use the
+ 	  built-in UART of the SoC, say Y to this option.
+--- a/drivers/tty/serial/ar933x_uart.c
++++ b/drivers/tty/serial/ar933x_uart.c
+@@ -13,6 +13,7 @@
+ #include <linux/console.h>
+ #include <linux/sysrq.h>
+ #include <linux/delay.h>
++#include <linux/gpio/consumer.h>
+ #include <linux/platform_device.h>
+ #include <linux/of.h>
+ #include <linux/of_platform.h>
+@@ -29,6 +30,8 @@
+ 
+ #include <asm/mach-ath79/ar933x_uart.h>
+ 
++#include "serial_mctrl_gpio.h"
++
+ #define DRIVER_NAME "ar933x-uart"
+ 
+ #define AR933X_UART_MAX_SCALE	0xff
+@@ -47,6 +50,8 @@ struct ar933x_uart_port {
+ 	unsigned int		min_baud;
+ 	unsigned int		max_baud;
+ 	struct clk		*clk;
++	struct mctrl_gpios	*gpios;
++	struct gpio_desc	*rts_gpiod;
+ };
+ 
+ static inline unsigned int ar933x_uart_read(struct ar933x_uart_port *up,
+@@ -100,6 +105,18 @@ static inline void ar933x_uart_stop_tx_i
+ 	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
+ }
+ 
++static inline void ar933x_uart_start_rx_interrupt(struct ar933x_uart_port *up)
++{
++	up->ier |= AR933X_UART_INT_RX_VALID;
++	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
++}
++
++static inline void ar933x_uart_stop_rx_interrupt(struct ar933x_uart_port *up)
++{
++	up->ier &= ~AR933X_UART_INT_RX_VALID;
++	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
++}
++
+ static inline void ar933x_uart_putc(struct ar933x_uart_port *up, int ch)
+ {
+ 	unsigned int rdata;
+@@ -125,11 +142,21 @@ static unsigned int ar933x_uart_tx_empty
+ 
+ static unsigned int ar933x_uart_get_mctrl(struct uart_port *port)
+ {
+-	return TIOCM_CAR;
++	struct ar933x_uart_port *up =
++		container_of(port, struct ar933x_uart_port, port);
++	int ret = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
++
++	mctrl_gpio_get(up->gpios, &ret);
++
++	return ret;
+ }
+ 
+ static void ar933x_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+ {
++	struct ar933x_uart_port *up =
++		container_of(port, struct ar933x_uart_port, port);
++
++	mctrl_gpio_set(up->gpios, mctrl);
+ }
+ 
+ static void ar933x_uart_start_tx(struct uart_port *port)
+@@ -140,6 +167,37 @@ static void ar933x_uart_start_tx(struct
+ 	ar933x_uart_start_tx_interrupt(up);
+ }
+ 
++static void ar933x_uart_wait_tx_complete(struct ar933x_uart_port *up)
++{
++	unsigned int status;
++	unsigned int timeout = 60000;
++
++	/* Wait up to 60ms for the character(s) to be sent. */
++	do {
++		status = ar933x_uart_read(up, AR933X_UART_CS_REG);
++		if (--timeout == 0)
++			break;
++		udelay(1);
++	} while (status & AR933X_UART_CS_TX_BUSY);
++
++	if (timeout == 0)
++		dev_err(up->port.dev, "waiting for TX timed out\n");
++}
++
++static void ar933x_uart_rx_flush(struct ar933x_uart_port *up)
++{
++	unsigned int status;
++
++	/* clear RX_VALID interrupt */
++	ar933x_uart_write(up, AR933X_UART_INT_REG, AR933X_UART_INT_RX_VALID);
++
++	/* remove characters from the RX FIFO */
++	do {
++		ar933x_uart_write(up, AR933X_UART_DATA_REG, AR933X_UART_DATA_RX_CSR);
++		status = ar933x_uart_read(up, AR933X_UART_DATA_REG);
++	} while (status & AR933X_UART_DATA_RX_CSR);
++}
++
+ static void ar933x_uart_stop_tx(struct uart_port *port)
+ {
+ 	struct ar933x_uart_port *up =
+@@ -153,8 +211,7 @@ static void ar933x_uart_stop_rx(struct u
+ 	struct ar933x_uart_port *up =
+ 		container_of(port, struct ar933x_uart_port, port);
+ 
+-	up->ier &= ~AR933X_UART_INT_RX_VALID;
+-	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
++	ar933x_uart_stop_rx_interrupt(up);
+ }
+ 
+ static void ar933x_uart_break_ctl(struct uart_port *port, int break_state)
+@@ -336,11 +393,20 @@ static void ar933x_uart_rx_chars(struct
+ static void ar933x_uart_tx_chars(struct ar933x_uart_port *up)
+ {
+ 	struct circ_buf *xmit = &up->port.state->xmit;
++	struct serial_rs485 *rs485conf = &up->port.rs485;
+ 	int count;
++	bool half_duplex_send = false;
+ 
+ 	if (uart_tx_stopped(&up->port))
+ 		return;
+ 
++	if ((rs485conf->flags & SER_RS485_ENABLED) &&
++	    (up->port.x_char || !uart_circ_empty(xmit))) {
++		ar933x_uart_stop_rx_interrupt(up);
++		gpiod_set_value(up->rts_gpiod, !!(rs485conf->flags & SER_RS485_RTS_ON_SEND));
++		half_duplex_send = true;
++	}
++
+ 	count = up->port.fifosize;
+ 	do {
+ 		unsigned int rdata;
+@@ -368,8 +434,14 @@ static void ar933x_uart_tx_chars(struct
+ 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ 		uart_write_wakeup(&up->port);
+ 
+-	if (!uart_circ_empty(xmit))
++	if (!uart_circ_empty(xmit)) {
+ 		ar933x_uart_start_tx_interrupt(up);
++	} else if (half_duplex_send) {
++		ar933x_uart_wait_tx_complete(up);
++		ar933x_uart_rx_flush(up);
++		ar933x_uart_start_rx_interrupt(up);
++		gpiod_set_value(up->rts_gpiod, !!(rs485conf->flags & SER_RS485_RTS_AFTER_SEND));
++	}
+ }
+ 
+ static irqreturn_t ar933x_uart_interrupt(int irq, void *dev_id)
+@@ -427,8 +499,7 @@ static int ar933x_uart_startup(struct ua
+ 		AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+ 
+ 	/* Enable RX interrupts */
+-	up->ier = AR933X_UART_INT_RX_VALID;
+-	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
++	ar933x_uart_start_rx_interrupt(up);
+ 
+ 	spin_unlock_irqrestore(&up->port.lock, flags);
+ 
+@@ -511,6 +582,21 @@ static const struct uart_ops ar933x_uart
+ 	.verify_port	= ar933x_uart_verify_port,
+ };
+ 
++static int ar933x_config_rs485(struct uart_port *port,
++				struct serial_rs485 *rs485conf)
++{
++	struct ar933x_uart_port *up =
++		container_of(port, struct ar933x_uart_port, port);
++
++	if ((rs485conf->flags & SER_RS485_ENABLED) &&
++	    !up->rts_gpiod) {
++		dev_err(port->dev, "RS485 needs rts-gpio\n");
++		return 1;
++	}
++	port->rs485 = *rs485conf;
++	return 0;
++}
++
+ #ifdef CONFIG_SERIAL_AR933X_CONSOLE
+ static struct ar933x_uart_port *
+ ar933x_console_ports[CONFIG_SERIAL_AR933X_NR_UARTS];
+@@ -680,6 +766,8 @@ static int ar933x_uart_probe(struct plat
+ 		goto err_disable_clk;
+ 	}
+ 
++	uart_get_rs485_mode(&pdev->dev, &port->rs485);
++
+ 	port->mapbase = mem_res->start;
+ 	port->line = id;
+ 	port->irq = irq_res->start;
+@@ -690,6 +778,7 @@ static int ar933x_uart_probe(struct plat
+ 	port->regshift = 2;
+ 	port->fifosize = AR933X_UART_FIFO_SIZE;
+ 	port->ops = &ar933x_uart_ops;
++	port->rs485_config = ar933x_config_rs485;
+ 
+ 	baud = ar933x_uart_get_baud(port->uartclk, AR933X_UART_MAX_SCALE, 1);
+ 	up->min_baud = max_t(unsigned int, baud, AR933X_UART_MIN_BAUD);
+@@ -697,6 +786,18 @@ static int ar933x_uart_probe(struct plat
+ 	baud = ar933x_uart_get_baud(port->uartclk, 0, AR933X_UART_MAX_STEP);
+ 	up->max_baud = min_t(unsigned int, baud, AR933X_UART_MAX_BAUD);
+ 
++	up->gpios = mctrl_gpio_init(port, 0);
++	if (IS_ERR(up->gpios) && PTR_ERR(up->gpios) != -ENOSYS)
++		return PTR_ERR(up->gpios);
++
++	up->rts_gpiod = mctrl_gpio_to_gpiod(up->gpios, UART_GPIO_RTS);
++
++	if ((port->rs485.flags & SER_RS485_ENABLED) &&
++	    !up->rts_gpiod) {
++		dev_err(&pdev->dev, "lacking rts-gpio, disabling RS485\n");
++		port->rs485.flags &= ~SER_RS485_ENABLED;
++	}
++
+ #ifdef CONFIG_SERIAL_AR933X_CONSOLE
+ 	ar933x_console_ports[up->port.line] = up;
+ #endif

target/linux/ath79/patches-5.4/405-mtd-tp-link-partition-parser.patch

@@ -21,5 +21,5 @@
  obj-y				+= parsers/
 +obj-$(CONFIG_MTD_TPLINK_PARTS)	+= tplinkpart.o
  
- # 'Users' - code which presents functionality to userspace.
- obj-$(CONFIG_MTD_BLKDEVS)	+= mtd_blkdevs.o
+ obj-$(CONFIG_MTD_SPLIT)		+= mtdsplit/
+ 

target/linux/ath79/patches-5.4/910-unaligned_access_hacks.patch

@@ -305,7 +305,7 @@
  	list_for_each_entry(p, head, list) {
 --- a/net/ipv4/tcp_output.c
 +++ b/net/ipv4/tcp_output.c
-@@ -457,48 +457,53 @@ static void tcp_options_write(__be32 *pt
+@@ -460,48 +460,53 @@ static void tcp_options_write(__be32 *pt
  	u16 options = opts->options;	/* mungable copy */
  
  	if (unlikely(OPTION_MD5 & options)) {
@@ -382,7 +382,7 @@
  	}
  
  	if (unlikely(opts->num_sack_blocks)) {
-@@ -506,16 +511,17 @@ static void tcp_options_write(__be32 *pt
+@@ -509,16 +514,17 @@ static void tcp_options_write(__be32 *pt
  			tp->duplicate_sack : tp->selective_acks;
  		int this_sack;
  
@@ -406,7 +406,7 @@
  		}
  
  		tp->rx_opt.dsack = 0;
-@@ -528,13 +534,14 @@ static void tcp_options_write(__be32 *pt
+@@ -531,13 +537,14 @@ static void tcp_options_write(__be32 *pt
  
  		if (foc->exp) {
  			len = TCPOLEN_EXP_FASTOPEN_BASE + foc->len;
@@ -706,7 +706,7 @@
  EXPORT_SYMBOL(xfrm_parse_spi);
 --- a/net/ipv4/tcp_input.c
 +++ b/net/ipv4/tcp_input.c
-@@ -3953,14 +3953,16 @@ static bool tcp_parse_aligned_timestamp(
+@@ -3958,14 +3958,16 @@ static bool tcp_parse_aligned_timestamp(
  {
  	const __be32 *ptr = (const __be32 *)(th + 1);
  
@@ -754,7 +754,7 @@
  	ptr = ip6hoff + sizeof(struct ipv6hdr);
 --- a/include/net/neighbour.h
 +++ b/include/net/neighbour.h
-@@ -274,8 +274,10 @@ static inline bool neigh_key_eq128(const
+@@ -273,8 +273,10 @@ static inline bool neigh_key_eq128(const
  	const u32 *n32 = (const u32 *)n->primary_key;
  	const u32 *p32 = pkey;
  
@@ -780,7 +780,7 @@
   * No flags defined yet.
 --- a/net/core/utils.c
 +++ b/net/core/utils.c
-@@ -443,8 +443,14 @@ void inet_proto_csum_replace16(__sum16 *
+@@ -460,8 +460,14 @@ void inet_proto_csum_replace16(__sum16 *
  			       bool pseudohdr)
  {
  	__be32 diff[] = {
@@ -799,7 +799,7 @@
  		*sum = csum_fold(csum_partial(diff, sizeof(diff),
 --- a/include/linux/etherdevice.h
 +++ b/include/linux/etherdevice.h
-@@ -496,7 +496,7 @@ static inline bool is_etherdev_addr(cons
+@@ -489,7 +489,7 @@ static inline bool is_etherdev_addr(cons
   * @b: Pointer to Ethernet header
   *
   * Compare two Ethernet headers, returns 0 if equal.
@@ -808,7 +808,7 @@
   * aligned OR the platform can handle unaligned access.  This is the
   * case for all packets coming into netif_receive_skb or similar
   * entry points.
-@@ -519,11 +519,12 @@ static inline unsigned long compare_ethe
+@@ -512,11 +512,12 @@ static inline unsigned long compare_ethe
  	fold |= *(unsigned long *)(a + 6) ^ *(unsigned long *)(b + 6);
  	return fold;
  #else