ramips: add support for Cudy WR1300

Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7612E
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
 - Power: DC 12V 1A tip positive

UART Serial:
  115200 baud
  Located on unpopulated 4 pin header near J4:

  J4
  [o] Rx
  [o] Tx
  [o] GND
  [ ] Vcc - Do not connect

Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:f0      label
WAN   *:f1      label + 1
2g    *:f0      label
5g    *:f2      label + 2

The label MAC address is found in bdinfo 0xde00.

Signed-off-by: Andrew Pikler <[email protected]>

target/linux/ramips/dts/mt7621_cudy_wr1300.dts

@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "cudy,wr1300", "mediatek,mt7621-soc";
+	model = "Cudy WR1300";
+
+	aliases {
+		led-boot = &led_sys;
+		led-failsafe = &led_sys;
+		led-running = &led_sys;
+		led-upgrade = &led_sys;
+		label-mac-device = &gmac0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_sys: sys {
+			label = "green:sys";
+			gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb {
+			label = "green:usb";
+			gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		wps {
+			label = "green:wps";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "u-boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition@40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0xf80000>;
+			};
+
+			partition@fd0000 {
+				label = "debug";
+				reg = <0xfd0000 0x10000>;
+				read-only;
+			};
+
+			partition@fe0000 {
+				label = "backup";
+				reg = <0xfe0000 0x10000>;
+				read-only;
+			};
+
+			bdinfo: partition@ff0000 {
+				label = "bdinfo";
+				reg = <0xff0000 0x10000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie0 {
+	wifi@0,0 {
+		compatible = "pci14c3,7603";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x0000>;
+		mtd-mac-address = <&bdinfo 0xde00>;
+		ieee80211-freq-limit = <2400000 2500000>;
+
+		led {
+			led-active-low;
+		};
+	};
+};
+
+&pcie1 {
+	wifi@0,0 {
+		compatible = "pci14c3,7662";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x8000>;
+		mtd-mac-address = <&bdinfo 0xde00>;
+		mtd-mac-address-increment = <2>;
+		ieee80211-freq-limit = <5000000 6000000>;
+
+		led {
+			led-sources = <2>;
+			led-active-low;
+		};
+	};
+};
+
+&gmac0 {
+	mtd-mac-address = <&bdinfo 0xde00>;
+};
+
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "lan4";
+		};
+
+		port@1 {
+			status = "okay";
+			label = "lan3";
+		};
+
+		port@2 {
+			status = "okay";
+			label = "lan2";
+		};
+
+		port@3 {
+			status = "okay";
+			label = "lan1";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "wan";
+			mtd-mac-address = <&bdinfo 0xde00>;
+			mtd-mac-address-increment = <1>;
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "wdt", "i2c", "jtag";
+		function = "gpio";
+	};
+};

target/linux/ramips/image/mt7621.mk

@@ -222,6 +222,16 @@ define Device/buffalo_wsr-600dhp
 endef
 TARGET_DEVICES += buffalo_wsr-600dhp
 
+define Device/cudy_wr1300
+  $(Device/dsa-migration)
+  IMAGE_SIZE := 15872k
+  DEVICE_VENDOR := Cudy
+  DEVICE_MODEL := WR1300
+  DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \
+	kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += cudy_wr1300
+
 define Device/dlink_dir-8xx-a1
   $(Device/dsa-migration)
   IMAGE_SIZE := 16000k